A wheel with an integral or removable rim designed to mount a pneumatic tire. Includes wheels without rims but designed to accommodate pneumatic tire rims. May include tire(s). Excludes:WHEEL, LANDING GEAR., WHEEL ASSEMBLY, AIRCRAFT
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED80956*)
CBBLDFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDGNH*;CBBLDGNJ$$DGNJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| GNH | LIGHTENING HOLE HUB CAP MOUNTING |
| GNJ | MOUNTING BOLT/STUD FACILITY |
ABFFDFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDCRV*;ABFFDCRX$$DAQW*)
| Table 1 |
| Reply Code (AB28) | Reply |
| CRW | BERRINGS |
| BNL | HUB |
| CRV | HUB CAP |
| CRU | LIGHTING HOLE |
| BAV | LUBRICANT FITTING |
| CRX | RIM FASTENING THREADED FACILITY |
| AQW | RING |
ABKVJOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKV3AEEJAB2.0*;ABKV3AEEJAB2.0$JAB2.0*;ABKV3AEEJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CYY | RIM |
| 3CZW | TIRE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BCNXDMOUNTING TYPE FOR WHICH DESIGNED
INDICATES THE TYPE OF MOUNTING FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BCNXDBJG)
| Table 1 |
| Reply Code (AM39) | Reply |
| BJJ | DUAL TIRE |
| BJG | SINGLE TIRE |
| BJH | SINGLE-DUAL TIRE |
AJXEASIZE DESIGNATOR
A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED.
Enter the alpha-numeric reply with a minimum of one character.
(AJXEAF5)
AAGL*JMAXIMUM INFLATION PRESSURE
THE MAXIMUM INFLATION PRESSURE FOR WHICH THE ITEM HAS BEEN RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAGLJV2.0*;AAGLJV2.0$$JV2.1*)
| Table 1 |
| Reply Code (AB18) | Reply |
| P | POUNDS |
| V | POUNDS PER SQUARE INCH |
CFHQ*JTIRE RIM NOMINAL DIAMETER
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE TIRE RIM,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHQJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CRDX*JTIRE LOAD MAXIMUM CAPACITY
THE DETERMINATION OF THE MAXIMUM OPERATIONAL LOAD CARRYING CAPACITY FOR WHICH THE TIRE IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRDXJKL2.0*;CRDXJKL2.0$$JKL2.1*)
| Table 1 |
| Reply Code (AN93) | Reply |
| K | KILOGRAMS |
| P | POUNDS |
| Table 2 |
| Reply Code (AN82) | Reply |
| D | DYNAMIC LOAD |
| X | EXTRA LOAD |
| G | LIGHT LOAD |
| L | LOAD LIMITS |
| T | LOAD RANGE B |
| U | LOAD RANGE C |
| V | LOAD RANGE D |
| W | LOAD RANGE E |
| N | STANDARD LOAD |
| S | STATIC LOAD |
DAAH*DITEM TYPE CATEGORY
THE CATEGORY THAT IDENTIFIES THE TYPE OF ITEM.
Enter the applicable reply code from the table below
(DAAHDAA*;DAAHDAB$DAC*;DAAHDAB$$DAC*)
| Table 1 |
| Reply Code (TC01) | Reply |
| AA | ACCESSORY |
| AD | INNER RIM |
| AC | ONE PIECE RIM |
| AE | OUTER RIM |
| AB | TIRE |
| AF | WHEEL ASSEMBLY |
ADVX*JRIM SURFACE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVXJAB2.0*;ADVXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
DAAA*AWHEEL ASSEMBLY NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER THAT DESIGNATES THE WHEEL ASSEMBLY.
Enter the numeric reply with a minimum of one digit.
(DAAAA10*)
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
DAAB*AONE PIECE RIM NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER THAT DESIGNATES THE ONE PIECE RIM.
Enter the numeric reply with a minimum of one digit.
(DAABA10*)
DAAC*AINNER RIM NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER THAT DESIGNATES THE INNER RIM.
Enter the numeric reply with a minimum of one digit.
(DAACA10*)
AAFV*APLY RATING
THE NUMERIC TERM PLY RATING IS USED AS AN INDEX OF STRENGTH AND DOES NOT NECESSARILY REPRESENT THE ACTUAL NUMBER OF CORD PLIES IN THE TIRE.
Enter the numeric reply with a minimum of one digit.
(AAFVA10*)
DAAD*AOUTER RIM NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER THAT DESIGNATES THE OUTER RIM.
Enter the numeric reply with a minimum of one digit.
(DAADA10*)
DAAE*ATIRE NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER THAT DESIGNATES THE TIRE.
Enter the numeric reply with a minimum of one digit.
(DAAEA10*)
IF STYLE/REPLY CODE(s) AFC OR AFD WERE ENTERED FOR MRC ARJD, YOU MUST ANSWER MRC (BPLM)
IF STYLE/REPLY CODE(s) AFE WERE ENTERED FOR MRC ARJD, YOU MUST ANSWER MRC (AWKJ)
ARJDDDESIGN FORM
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(ARJDDAFD)
| Table 1 |
| Reply Code (AL52) | Reply |
| AFC | DISK |
| AFD | DISK W/REINFORCING SPOKES |
| AFE | SPOKE |
DAAJ*DACCESSORY TYPE
THE CATEGORY THAT IDENTIFIES THE TYPE OF ACCESSORY.
Enter the applicable reply code from the table below
(DAAJDAG*;DAAJDAK$DAF*;DAAJDAK$$DAF*)
| Table 1 |
| Reply Code (AC47) | Reply |
| AK | ADAPTER |
| AD | CAP |
| AE | CHAIN |
| AB | EQUIPMENT |
| AJ | FLAP |
| AG | INNER TUBE |
| AM | RUN FLAT INSERT |
| AF | STRAP |
| AL | TIRE GAGE |
| AA | TOOL |
| AH | VALVE |
| AC | WHEEL WEIGHT |
IF STYLE/REPLY CODE(s) ACY WERE ENTERED FOR MRC BPLM, YOU MUST ANSWER MRC (CFHS)
BPLMDDISK TYPE
INDICATES THE TYPE OF DISK.
Enter the applicable reply code from the table below
(BPLMDACY)
| Table 1 |
| Reply Code (AK95) | Reply |
| AHE | DOUBLE |
| ACY | SINGLE |
IF STYLE/REPLY CODE(s) BL OR BM WERE ENTERED FOR MRC CFHS, YOU MUST ANSWER MRC (CFHT)
CFHS*DMOUNTING FACE TYPE
INDICATES THE TYPE OF MOUNTING FACE.
Enter the applicable reply code from the table below
(CFHSDBM)
| Table 1 |
| Reply Code (AG89) | Reply |
| BK | CENTERED |
| BL | CONCAVE |
| BM | CONVEX |
CFHT*JOFFSET DISTANCE FROM RIM CENTERLINE TO OUTSIDE WHEEL MOUNTING FACE
THE OFFSET DISTANCE FROM THE CENTERLINE OF THE RIM TO THE OUTSIDE OF THE WHEEL MOUNTING FACE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHTJAC2.0*;CFHTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CNJK*ALIGHTENING HOLE QUANTITY
THE NUMBER OF LIGHTENING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(CNJKA10*)
CNJM*JHUB CAP MOUNTING DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HUB CAP MOUNTING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNJMJAA2.0*;CNJMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AWKJ*ASPOKE QUANTITY
THE NUMBER OF SPOKES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AWKJA10*)
CNJG*JSPOKE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SPOKE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNJGJAA2.0*;CNJGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CNJH*JSPOKE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A SPOKE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNJHJAC2.0*;CNJHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CNJJ*JSPOKE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A SPOKE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNJJJAB2.0*;CNJJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) EJP WERE ENTERED FOR MRC APGF, YOU MUST NOT ANSWER MRC (CNJG and CNJH and CNJJ)
APGFDDESIGN TYPE
INDICATES THE DESIGN TYPE OF THE ITEM.
Enter the applicable reply code from the table below
(APGFDEJO*;APGFDEJL$DEJK*)
| Table 1 |
| Reply Code (AK54) | Reply |
| EJK | DEMOUNTABLE RIM |
| EJL | DIVIDED RIM |
| EJM | DIVIDED WHEEL |
| EJN | INTEGRAL RIM |
| EJP | SPIDER |
ABGA*JGROOVE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGAJAA2.0*;ABGAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGF*JGROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGFJAB2.0*;ABGFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMKJOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEUA*JEFFECTIVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEUAJAB2.0*;AEUAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGFF*JFLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLANGE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGFFJAC2.0*;AGFFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BNPQ*JMETAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE METAL,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BNPQJAA2.0*;BNPQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFJB*JWHEEL WIDTH AT OUTSIDE DIAMETER
THE WIDTH OF THE WHEEL AT THE OUTSIDE DIAMETER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFJBJAC2.0*;CFJBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1, 4, 6, 7, 9 OR 22 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and BNPQ)
IF STYLE/REPLY CODE(s) 2 OR 5 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and ABGF and BNPQ and ABGA)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and ABGF and AGFF and BNPQ)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and ABGA and ABGF and BNPQ and AGFF)
IF STYLE/REPLY CODE(s) 10, 11, 12, 13, 14, 15, 16, 17, 18 OR 24 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and BNPQ and ABGA)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and BNPQ and AGFF)
IF STYLE/REPLY CODE(s) 20, 21 OR 23 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (AGFF and ABMK and ABGA and BNPQ)
IF STYLE/REPLY CODE(s) 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42 OR 43 WERE ENTERED FOR MRC AJUP, YOU MUST ANSWER MRC (ABMK and AEUA and ABGA)
AJUP*LRIM STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RIM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AJUPL31)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAA1166 | 1 | FLAT |
| AAA1175 | 10 | DROP CENTER |
| AAA1176 | 11 | DROP CENTER |
| AAA1177 | 12 | FULL DROP CENTER |
| AAA1178 | 13 | FLAT BASE |
| AAA1179 | 14 | FULL DROP CENTER |
| AAA1180 | 15 | CURVED BASE |
| AAA1181 | 16 | V CENTER |
| AAA1182 | 17 | CLINCHER |
| AAA1183 | 18 | DROP CENTER |
| AAA1184 | 19 | SINGLE FLANGE |
| AAA1167 | 2 | DROP CENTER |
| AAA1185 | 20 | U BASE |
| AAA1186 | 21 | REVERSE CLINCHER |
| AAA1187 | 22 | ANGLE L |
| AAA1188 | 23 | SLANT |
| AAA1189 | 24 | LOW CENTER CLINCHER |
| AAA1190 | 25 | DROP CENTER LOCK |
| AAA1191 | 26 | FLAT LOCK |
| AAA1192 | 27 | DROP CENTER LOCK |
| AAA1193 | 28 | FLAT LOCK |
| AAA1194 | 29 | DROP CENTER LOCK |
| AAA1168 | 3 | DROP CENTER |
| AAA1195 | 30 | FLAT LOCK |
| AAA1196 | 31 | DROP CENTER LOCK |
| AAA1197 | 32 | DROP CENTER LOCK |
| AAA1198 | 33 | DROP CENTER LOCK |
| AAA1199 | 34 | FLAT LOCK |
| AAA1200 | 35 | FLAT LOCK |
| AAA1201 | 36 | MODERATE DROPCENTER LOCK |
| AAA1202 | 37 | DEEP DROP CENTERLOCK |
| AAA1203 | 38 | FLAT CENTER LOCK |
| AAA1204 | 39 | DROP CENTER LOCK |
| AAA1169 | 4 | HALF MOON |
| AAA1205 | 40 | DROP CENTER LOCK |
| AAA1206 | 41 | FLAT CENTER LOCK |
| AAA1207 | 42 | FLAT CENTER LOCK |
| AAA1208 | 43 | FLAT CENTER LOCK |
| AAA1170 | 5 | FLAT RIM |
| AAA1171 | 6 | CONCAVE |
| AAA1172 | 7 | CONVEX |
| AAA1173 | 8 | GROOVED |
| AAA1174 | 9 | FLANGED |
IF STYLE/REPLY CODE(s) ACP WERE ENTERED FOR MRC CFJD, YOU MUST ANSWER MRC (CNSN and CNSQ)
IF STYLE/REPLY CODE(s) AAE WERE ENTERED FOR MRC CFJD, YOU MUST ANSWER MRC (CNSN and CNSQ and CNSR)
CFJD*DRIM FASTENING FACILITY
THE FACILITY FOR WHICH THE RIM IS FASTENED.
Enter the applicable reply code from the table below
(CFJDDACP)
| Table 1 |
| Reply Code (AM39) | Reply |
| ACP | HOLE |
| AAE | STUD(S) |
CNSN*ARIM FASTENING FACILITY QUANTITY
THE NUMBER OF FACILITIES FOR FASTENING THE RIM.
Enter the numeric reply with a minimum of one digit.
(CNSNA10*)
CNSQ*DRIM FASTENING FACILITY THREAD DIRECTION
THE DIRECTION OF THE THREAD FOR A RIM FASTENING FACILITY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CNSQDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CNSR*JRIM FASTENING STUD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE RIM FASTENING STUD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNSRJAC2.0*;CNSRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAB2.0*;AARXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZT*JSLOT DEPTH
THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE SLOT,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZTJAB2.0*;AAZTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJAC2.0*;ABNMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQYZ*JINSIDE CIRCUMFERENCE
THE DISTANCE AROUND THE INSIDE SURFACE OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQYZJAA2.0*;BQYZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXHR*JMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AXHRJAAE2*)
| Table 1 |
| Reply Code (AM39) | Reply |
| BHE | BOLT HOLE |
| AAE | STUD(S) |
CNSS*JMOUNTING FACILITY BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FACILITY BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CNSSJAC2.0*;CNSSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) APL WERE ENTERED FOR MRC CDMC, YOU MUST ANSWER MRC (BFYT)
CDMC*DVALVE HOLE SHAPE
THE PHYSICAL CONFIGURATION OF THE VALVE HOLE.
Enter the applicable reply code from the table below
(CDMCDARY)
| Table 1 |
| Reply Code (AD07) | Reply |
| APL | ROUND |
| ARY | SLOTTED |
BFYT*GHOLE LOCATION
INDICATES THE LOCATION OF THE HOLE ON THE ITEM.
Enter clear text.
(BFYTGCLEARTEXT)
CFJHDHUB CHARACTERISTIC
AN INDICATION OF THE CHARACTERISTIC OF THE HUB.
Enter the applicable reply code from the table below
(CFJHDAAY)
| Table 1 |
| Reply Code (AJ88) | Reply |
| AAX | DEMOUNTABLE |
| AAY | INTEGRAL |
IF STYLE/REPLY CODE(s) C1, C2, C3, C5, C6, C7, C9, C10 OR C11 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (ABKW and AAZT and AARX and BQYZ)
IF STYLE/REPLY CODE(s) C4 OR C8 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (ABKW)
IF STYLE/REPLY CODE(s) D1, D2, D3, D4, D5, D6, D8, D10, D12 OR D13 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (ABKW and AAZT and AARX and BQYZ)
IF STYLE/REPLY CODE(s) D7 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (ABKW and BQYZ and ABNM)
IF STYLE/REPLY CODE(s) D9 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (BQYZ and AARX and ABNM and ABKW)
IF STYLE/REPLY CODE(s) D11 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (ABKW and BQYZ and AAZT)
IF STYLE/REPLY CODE(s) E1, E2, E3, E4, E5, E6, E7 OR E8 WERE ENTERED FOR MRC ACXD, YOU MUST ANSWER MRC (ABKW and BQYZ and AARX and AAZT)
ACXD*LRING STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE RING.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACXDLC2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAA1216 | C1 | RIM LOCK RING SLOTTED |
| AAA1225 | C10 | RIM LOCK RING SLOTTED |
| AAA1226 | C11 | RIM LOCK RING SLOTTED |
| AAA1217 | C2 | RIM LOCK RING SLOTTED |
| AAA1218 | C3 | RIM LOCK RING SLOTTED |
| AAA1219 | C4 | RIM LOCK RING SLOTTED |
| AAA1220 | C5 | RIM LOCK RING SLOTTED |
| AAA1221 | C6 | RIM LOCK RING SLOTTED |
| AAA1222 | C7 | RIM LOCK RING SLOTTED |
| AAA1223 | C8 | RIM LOCK RING SLOTTED |
| AAA1224 | C9 | RIM LOCK RING SLOTTED |
| AAA1227 | D1 | RIM SIDE RING SLOTTED |
| AAA1236 | D10 | RIM SIDE RING SLOTTED |
| AAA1237 | D11 | RIM SIDE RING SLOTTED |
| AAA1238 | D12 | RIM SIDE RING SLOTTED |
| AAA1239 | D13 | RIM SIDE KEY SLOTTED |
| AAA1228 | D2 | RIM SIDE RING SLOTTED |
| AAA1229 | D3 | RIM SIDE RING SLOTTED |
| AAA1230 | D4 | RIM SIDE RING SLOTTED |
| AAA1231 | D5 | RIM SIDE RING SLOTTED |
| AAA1232 | D6 | RIM SIDE RING SLOTTED |
| AAA1233 | D7 | RIM SIDE RING SLOTTED |
| AAA1234 | D8 | RIM SIDE RING SLOTTED |
| AAA1235 | D9 | RIM SIDE RING KEY |
| AAA1240 | E1 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1241 | E2 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1242 | E3 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1243 | E4 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1244 | E5 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1245 | E6 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1246 | E7 | RIM SIDE AND LOCK RING SLOTTED |
| AAA1247 | E8 | RIM SIDE AND LOCK RING SLOTTED |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHSX*JAXLE RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHSXJAA2.0*;CHSXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHSY*JAXLE RECESS MAJOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHSYJAB2.0*;CHSYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHSZ*JAXLE RECESS MINOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHSZJAB2.0*;CHSZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTB*JSAND BAND RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTBJAA2.0*;CHTBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTC*JSAND BAND RECESS MAJOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTCJAA2.0*;CHTCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTD*JSAND BAND RECESS MINOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTDJAC2.0*;CHTDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTF*JBEARING RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTFJAB2.0*;CHTFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTG*JSAND BAND RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTGJAB2.0*;CHTGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTH*JMAJOR SAND BAND RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTHJAB2.0*;CHTHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTJ*JMINOR SAND BAND RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTJJLA2.0*;CHTJJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CHTK*JBEARING RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CHTKJAB2.0*;CHTKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYDT*DBEARING TYPE
INDICATES THE TYPE OF BEARING PROVIDED.
Enter the applicable reply code from the table below
(BYDTDAK*;BYDTDA$$DAR*)
| Table 1 |
| Reply Code (AH96) | Reply |
| A | ANY ACCEPTABLE |
| AE | BALL |
| AS | OIL IMPREGNATED BRONZE |
| AB | PLAIN |
| AT | PLAIN SLEEVE |
| AR | PLAIN, SELF-LUBRICATED |
| AJ | ROLLER |
| BG | SEALED ROLLER |
| AW | SELF-LUBRICATING POROUS BRONZE FLANGED |
| AK | SLEEVE |
| AX | STANDARD ROLLER |
| AY | STRAIGHT ROLLER |
| AQ | TAPERED ROLLER |
BDDY*ABEARING QUANTITY
THE NUMBER OF BEARINGS PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(BDDYA10*)
BDFN*JBEARING INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BEARING,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDFNJAB2.0*;BDFNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUV*JBEARING SURFACE WIDTH
A MEASUREMENT TAKEN ACROSS THE BEARING SURFACE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUVJAB2.0*;ADUVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHEG*JPILOT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PILOT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHEGJAB2.0*;AHEGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (ABHP and CHSX and CHTB and CHTG)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (CHTC and ABHP and CHSY and CHTH and CHSZ and CHTD and CHTJ)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (ABHP and CHSX)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (ABHP and CHSY and CHSX)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (ABHP and CHTF and CHSX and CHTB and CHTG and CHTK)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (ABHP and CHSY and CHSX)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC CXQW, YOU MUST ANSWER MRC (ABHP and CHSX)
CXQW*LHUB STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HUB.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CXQWL3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAA1209 | 1 | SINGLE RECESS STRAIGHT |
| AAA1210 | 2 | SINGLE RECESS TAPERED |
| AAA1211 | 3 | STRAIGHT |
| AAA1212 | 4 | TAPERED |
| AAA1213 | 5 | DOUBLE RECESS STRAIGHT |
| AAA1214 | 6 | TAPERED |
| AAA1215 | 7 | STRAIGHT |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFFL*JMOUNTING BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFFLJAB2.0*;AFFLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAVGEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ALQF*DRING TYPE
THE TYPE OF RING(S) USED ON THE ITEM.
Enter the applicable reply code from the table below
(ALQFDPJ*;ALQFDPK$DPL*;ALQFDPK$$DPL*)
| Table 1 |
| Reply Code (AB47) | Reply |
| PJ | LOCK |
| PK | SIDE |
| PL | SIDE-LOCK |
ABUJ*ATHREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the alpha-numeric reply with a minimum of one character.
(ABUJAI7)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information