An axle mounted in place of a normal axle on a machine, on a hoisting unit on a chairlift, and the like, to measure loads or forces to prevent overloads.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED80593*)
CSBHJVOLTAGE IN VOLTS AND CURRENT TYPE
THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHETHER ALTERNATING OR DIRECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBHJAP2.0*;CSBHJAP2.0$JAP2.0*;CSBHJAP2.0$$JAP2.1*)
| Table 1 |
| Reply Code (AN87) | Reply |
| AC | AC |
| AD | AC/DC |
| AP | AC-PEAK |
| AR | AC-RMS |
| DC | DC |
| AA | VOLTAGE DIRECT CURRENT |
AFGAJOPERATING TEMP RANGE
THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFGAJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
ACDCDCURRENT TYPE
INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.
Enter the applicable reply code from the table below
(ACDCDC*;ACDCDB$DD*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| D | AC/DC |
| C | DC |
AYMPJGROSS WEIGHT
THE WEIGHT OF THE ITEM FULLY EQUIPPED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYMPJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
BGSTJPRESSURE RATING
THE PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGSTJJSB2.0*;BGSTJJSB2.0$$JJSB2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| ES | GRAMS PER SQUARE METER |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| FB | POUNDS PER SQUARE INCH |
| JS | POUNDS PER SQUARE INCH GAGE |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBLDFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDGGZ*;CBBLDGGY$$DGGY*)
| Table 1 |
| Reply Code (AN47) | Reply |
| GGZ | ZERO ADJUSTER NOT PROVIDED |
| GGY | ZERO ADJUSTER PROVIDED |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDSTA000*;MATTDCUB000$DSTB000*;MATTDCUB000$$DSTB000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUB000 | COPPER ALLOY |
| PCA000 | PLASTIC |
| RCE000 | RUBBER |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
ANSLJINPUT IMPEDANCE RATING
THE TOTAL OPPOSITON (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE INPUT FLOW OF ALTERNATING CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANSLJKR2.0*)
| Table 1 |
| Reply Code (AE75) | Reply |
| GF | GIGOHMS |
| KR | KILOHMS |
| MR | MEGOHMS |
| QR | OHMS |
ANSRJOUTPUT IMPEDANCE RATING
THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) WHICH THE ITEM OFFERS TO THE OUTPUT FLOW OF ALTERNATING CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANSRJGF2.0*)
| Table 1 |
| Reply Code (AE75) | Reply |
| GF | GIGOHMS |
| KR | KILOHMS |
| MR | MEGOHMS |
| QR | OHMS |
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDAPY)
| Table 1 |
| Reply Code (AM39) | Reply |
| AQP | BACKPLATE |
| APY | BENCH |
| AFF | BEZEL RING |
| AQQ | BOARD |
| AQS | BODY |
| AAC | BOLT |
| ABC | BRACKET |
| ABD | BUSHING |
| ANR | CABINET |
| AQT | CABLE |
| AQW | CABLE ATTACHED TO SHACKLES |
| ABF | CASE |
| ABH | CLAMP |
| ACX | CLAMP RING |
| ADR | CLEVIS |
| AFL | CLIP |
| AFQ | CONNECTOR |
| ACR | FLANGE |
| AGQ | FLUSH |
| AFW | FRAME |
| ABL | FRICTION |
| AQX | HANDLE |
| ACP | HOLE |
| AGG | HOOK |
| AED | PANEL |
| ABP | PLUG-IN |
| ABR | RACK |
| AAN | ROD END |
| ABW | SCREW |
| AGY | SCREW CLAMP |
| AGZ | SCREW LOCK |
| AQY | SEMIFLUSH |
| AQZ | SHACKLE |
| ARA | SHEAVES |
| APH | SHOCK |
| ARB | SHOCKPROOF BASE |
| AGX | SIDE |
| ARC | SLING |
| AEF | SOCKET |
| AJM | STAND |
| AAE | STUD |
| AEG | SURFACE |
| ARD | TABLE |
| ACD | TERMINAL |
| AQR | TERMINAL BOARD |
| ARE | UNIVERSAL |
| ARF | WAVEGUIDE |
CTHB*JBREAKING STRENGTH
THE MEASURED LOAD REQUIRED TO BREAK THE ITEM IN TENSION.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTHBJBWC2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BW | DECANEWTON |
| AJ | KILOGRAMS |
| BT | NEWTON |
| AS | POUNDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGBD*DELECTRICAL CONNECTION TYPE
INDICATES THE TYPE OF ELECTRICAL CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AGBDDEL)
| Table 1 |
| Reply Code (AE79) | Reply |
| EK | CONNECTOR |
| EB | CONNECTOR PLUG |
| AB | CONNECTOR RECEPTACLE |
| AJ | CORD W/ATTACHED PLUG |
| EL | LEAD, MOLDED-IN |
| EJ | LUG |
| AG | TERMINAL |
| AF | TERMINAL BLOCK |
| EM | TERMINAL BOX |
| AH | WIRE LEAD |
BGRQ*DCABLE TYPE
INDICATES THE TYPE OF CABLE PROVIDED.
Enter the applicable reply code from the table below
(BGRQDB)
| Table 1 |
| Reply Code (AC00) | Reply |
| B | INPUT |
| M | INPUT-OUTPUT |
| F | OUTPUT |
ABJP*JPOWER CABLE LENGTH
THE LENGTH MEASURED FROM THE ELEMENT TO THE EXTREME END OF THE POWER CABLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJPJMB2.0*;ABJPJMB2.0$$JMB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGBG*ACONNECTOR IDENTIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURER'S NUMBER OR SYMBOL USED TO IDENTIFY THE CONNECTOR.
Enter the alpha-numeric reply with a minimum of one character.
(AGBGAU5)
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJLC2.0*;ABMKJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJLC2.0*;ADAVJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
GRWT*JGROSS WEIGHT
THE COMBINED WEIGHT OF THE ITEM AND ITS LOADED CONTENTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(GRWTJBMMT2.0*;GRWTJBMMT2.0$$JBMMT2.1*)
| Table 1 |
| Reply Code (AD28) | Reply |
| CU | 1 HANDLE AT EACH END |
| DX | 1 HANDLE AT EACH SIDE |
| CW | 1 WEBBING LOOP EACH SIDE |
| CX | 1 WEBBING LOOP ON 4 CORNERS |
| DW | 2 HANDLES AT EACH END |
| CZ | 3 OBLONG METAL RINGS EITHER SIDE |
| CY | 3 WEBBING LOOPS EITHER SIDE |
| AV | AUTOMATIC DATA PROCESSING SERVER |
| CD | BAIL |
| CR | BAR |
| BW | BECKET |
| AB | BELT ATTACHMENTS |
| CF | BELT STRAP |
| AY | BOLT ON EAR |
| CJ | BOW |
| DY | BOW HANDLE |
| AC | BRAKE TYPE CASTERS |
| AA | CAMERA |
| CE | CASTERS |
| CM | CONTROL HEAD ASSEMBLY |
| AW | CRADLE |
| AX | DAVIT |
| CG | DETACHABLE SHOULDER STRAP |
| BU | DISPLAY UNIT |
| DS | D-RING |
| DP | D-RING W/TAB |
| DE | FIXED CASTERS |
| AE | FIXED EXTERNAL HANDLES |
| DJ | FIXED KNOB |
| AZ | FIXED LIFTING EARS ON CRADLE |
| DK | FIXED LOOP |
| EA | FOLD OVER HANDLE |
| DZ | FOLDING |
| BA | GRIPS |
| BB | GRIPS, FINGERHOLE |
| DC | HAND PUSHED |
| AJ | HAND STRAP |
| CP | HANDHOLES |
| BY | HANDLE |
| BD | HANDLE ON END |
| BE | HANDLE ON SIDE |
| BF | HANDLE ON TOP |
| AL | HANDLE, ADJUSTABLE |
| BH | HANDLE, EACH END, FOLDING |
| BL | HANDLE, EACH END, RING |
| BJ | HANDLE, FRONT, FOLDING |
| AM | HANDLE, NONADJUSTABLE |
| BK | HANDLE, PULL, REMOVABLE |
| BG | HANDLES, FLUSH FOLDING |
| BC | HANDLES, METAL |
| AF | HINGED EXTERNAL HANDLES |
| DT | HOOK |
| AN | KNOB |
| CB | L-HANDLE |
| CV | LIFTING CHAIN |
| BM | LIFTING EAR |
| AH | LIFTING EYES |
| BN | LIFTING FLANGE |
| BP | LIFTING LUGS |
| BX | LOOP |
| EH | LOW SLOPING TOP |
| DG | MANUAL |
| CH | NECK STRAP |
| AD | NONBRAKE TYPE CASTERS |
| DV | OPEN CONTOURED HANDLE |
| DU | OPEN FINGER GRIP |
| AR | PALLET |
| EJ | PALLET DOMESTIC, US NAVY |
| EK | PALLET FLEET, US NAVY |
| ED | PALLET, US AIR FORCE |
| EE | PALLET, US ARMY |
| EF | PALLET, US MARINE CORPS |
| EG | PALLET, US NAVY |
| DN | PISTOL GRIP |
| DH | POWER |
| CA | PULL RING |
| AS | PULL RING/TAB |
| DA | PUSHED |
| AG | RECESSED HANDLES |
| DL | REMOVABLE LOOP |
| CS | RETRACTABLE HANDLES |
| CL | ROD |
| BZ | ROPE |
| DD | SELF-PROPELLED |
| EB | SHIPPING CONTAINER |
| AK | SHOULDER STRAP |
| CN | SIDE DROP HANDLES |
| AP | SKID |
| DQ | SLIDE LOCK KEEPER |
| DM | SLIDING LOOP |
| AT | SLING |
| BQ | SLING, ENDLESS |
| BR | SNAP CATCH |
| EL | SNAP FASTENER |
| DR | SNAP HOOK |
| CK | STAFF |
| AU | STEERING FLANGE |
| BS | STRAP |
| BT | STRAP, NYLON WEB |
| DF | SWIVEL CASTERS |
| BV | TERMINAL |
| CC | T-HANDLE |
| DB | TOWED |
| CT | TRACKS |
| EC | W/HANDLES OR GRIPS |
| AQ | WHEELS |
| Table 2 |
| Reply Code (AG67) | Reply |
| HU | 120MIN/4.7GB |
| EU | 18MIN/150MB |
| EJ | 21MIN/180MB |
| HV | 240MIN/8.5GB |
| JU | 260MIN/9.4GB |
| GU | 30MIN/1.4GB |
| JV | 480MIN/17.1GB |
| GV | 60MIN/2.8GB |
| DV | 63MIN/550MB |
| DU | 74MIN/650MB |
| FV | 80MIN/700MB |
| GY | AWG |
| BF | BAG |
| BG | BALL |
| LM | BAR |
| HA | BARRELS |
| KB | BED |
| BH | BUNDLE |
| GP | BUSHELS |
| MT | BYTES |
| AB | CAPSULES |
| JJ | CARAT |
| KE | CARTRIDGES |
| KJ | CENTIGRADE |
| BS | CENTILITER |
| MP | CENTIMETER |
| BU | CENTIMETERS PER MINUTE |
| MU | CHARACTERS |
| GZ | CIR MIL |
| HE | CIRCULAR MIL |
| AC | CUBIC CENTIMETERS |
| MW | CUBIC CENTIMETERS PER MINUTE |
| BZ | CUBIC DECIMETERS |
| CY | CUBIC FEET |
| EM | CUBIC FEET PER HOUR |
| EK | CUBIC FEET PER MINUTE |
| CP | CUBIC INCHES |
| KV | CUBIC INCHES PER MINUTE |
| LD | CUBIC METERS |
| HD | CUBIC METERS PER MINUTE |
| MC | CUBIC METERS PER SECOND |
| CA | CUBIC MILLIMETERS |
| DR | CUBIC YARDS |
| HS | CUBIC YARDS PER MINUTE |
| DJ | CUPS |
| JF | CURIES |
| GL | DAYS |
| BW | DECANEWTON |
| CB | DECILITERS |
| GT | DEG CELSIUS |
| GW | DEG FAHRENHEIT |
| LU | DEG KELVIN |
| CE | DEGREES |
| JY | DENTAL FILM PACKET |
| DM | DIVISIONS PER INCH |
| MR | DOSES |
| BJ | DOZEN |
| CD | DRAMS |
| KU | DYNAMIC HOOK LOAD, POUNDS |
| HL | DYNES |
| KG | ENVELOPES PER HOUR |
| KH | ENVELOPES PER MINUTE |
| KK | FAHRENHEIT |
| BB | FEET |
| FE | FEET PER MINUTE |
| HH | FEET PER POUND |
| KL | FILM PACKET |
| JZ | FLASKS |
| AD | FLUID DRAMS |
| AE | FLUID OUNCES |
| GG | FOOT |
| BK | FOOT, ROLL |
| FK | GALLON, IMPERIAL MEASURE |
| FJ | GALLON, US MEASURE |
| AF | GALLONS |
| EV | GALLONS IMPERIAL MEASURE |
| GH | GALLONS PER DAY |
| HQ | GALLONS PER GALLON |
| LN | GALLONS PER HOUR |
| CQ | GALLONS PER MINUTE |
| FU | GALLONS US MEASURE |
| DX | GAUSS |
| MF | GIGABECQUERELS |
| ML | GIGABYTES |
| NC | GIGAOCTETS |
| EZ | GILLS |
| AG | GRAINS |
| JP | GRAINS PER INGOT |
| KW | GRAMMES PER CUBIC CENTIMETRE |
| BA | GRAMS |
| LX | GRAMS PER CUBIC CENTIMETER |
| FT | GRAMS PER LINEAR CENTIMETER |
| LC | GRAMS PER LINEAR METER |
| CF | GRAMS PER LITER |
| JT | GRAMS PER LITER OF SOLUTION |
| KR | GRAMS PER MILLIMETER |
| ES | GRAMS PER SQUARE METER |
| HT | HECTOBARS |
| CH | HECTOGRAMS |
| LW | HECTOPASCAL |
| FQ | HOURS |
| DS | HUNDREDTHS OF A FOOT |
| BC | INCHES |
| FR | INCHES OF MERCURY |
| FA | INCHES OF MERCURY ABSOLUTE PRESSURE |
| AU | INCHES PER MINUTE |
| MH | JAR |
| MM | KILOBYTES |
| DY | KILOGAUSS |
| AJ | KILOGRAMS |
| GS | KILOGRAMS OF WATER |
| HX | KILOGRAMS OF WATER PER HOUR |
| EH | KILOGRAMS PER 100 SQUARE METERS |
| MG | KILOGRAMS PER CUBIC DECIMETER |
| DB | KILOGRAMS PER CUBIC METER |
| JE | KILOGRAMS PER HECTARE |
| GQ | KILOGRAMS PER HOUR |
| CT | KILOGRAMS PER METER |
| CN | KILOGRAMS PER MILLIMETER |
| HB | KILOGRAMS PER MINUTE |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| KS | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| CX | KILOGRAMS PER SQUARE METER |
| JA | KILOGRAMS PER SQUARE MILLIMETER |
| EA | KILOMAXWELLS |
| GM | KILOMETERS PER HOUR |
| LT | KILONEWTONS |
| LG | KILOPASCALS |
| MJ | KIT |
| GC | KNOTS |
| CC | LITERS |
| GK | LITERS PER DAY |
| GJ | LITERS PER HOUR |
| HR | LITERS PER LITER |
| CR | LITERS PER MINUTE |
| AH | LOZENGE |
| GB | MAN-HOURS |
| GA | MAN-MINUTES |
| HY | MANOMETRIC |
| DZ | MAXWELLS |
| LE | MEGABECQUERELS |
| MN | MEGABYTES |
| LJ | MEGAPASCALS |
| CK | METERS |
| KM | METERS PER KILOGRAM |
| FH | METERS PER MINUTE |
| CV | METERS PER SECOND |
| BX | METRIC TONS |
| FG | METRIC TONS PER HOUR |
| JH | MICROCURIES |
| AK | MICROGRAMS |
| HN | MICROLITERS |
| GD | MICRONS |
| CJ | MILE |
| GE | MILES PER HOUR |
| DN | MILES PER INCH |
| KN | MILLIBARS |
| JG | MILLICURIES |
| AL | MILLIGRAMS |
| JK | MILLIGRAMS PER CUBIC CENTIMETER |
| AM | MILLILITERS |
| LF | MILLILITERS PER GALLON |
| HG | MILLILITERS PER MINUTE |
| HC | MILLIMETERS |
| KZ | MILLIMETERS OF MERCURY |
| KX | MILLIVOLTS |
| DL | MILS |
| HP | MINIMS |
| DF | MINUTES |
| BT | NEWTON |
| LS | NEWTONS PER 10 MILLIMETERS WIDE |
| LP | NEWTONS PER 15 MILLIMETERS WIDE |
| LQ | NEWTONS PER 25 MILLIMETERS WIDE |
| LR | NEWTONS PER 50 MILLIMETERS WIDE |
| LH | NEWTONS PER MILLIMETER |
| JR | NEWTONS PER SQUARE CENTIMETER |
| LV | NEWTONS PER SQUARE MILLIMETER |
| EB | OERSTEDS |
| MQ | OIL FLOW RATE |
| AN | OUNCES |
| KQ | OUNCES PER INCH |
| FS | OUNCES PER LINEAR FOOT |
| LB | OUNCES PER LINEAR YARD |
| MK | OUNCES PER SECOND |
| EX | OUNCES PER SQUARE FOOT |
| KY | OUNCES PER SQUARE INCH |
| ER | OUNCES PER SQUARE YARD |
| DG | OUNCES, AVOIRDUPOIS |
| DH | OUNCES, FLUID |
| KT | OUNCES, TROY |
| BL | PACK, FOIL |
| BM | PACKET |
| MX | PAD |
| DP | PARTS PER INCH |
| KC | PATIENT |
| FX | PECK |
| AP | PELLETS |
| JL | PENNYWEIGHT |
| JQ | PENNYWEIGHT PER PLATE |
| FZ | PER CYCLE |
| FY | PER HOUR |
| ET | PER INCH OF LENGTH |
| JC | PER KILOGRAM |
| EW | PER MILLIMETER OF LENGTH |
| MV | PER MINUTE |
| JB | PER POUND |
| MD | PER SQUARE INCH |
| ME | PER SQUARE METER |
| CG | PERCENT |
| EE | PERCENT PER DEG CELSIUS |
| EF | PERCENT PER DEG FAHRENHEIT |
| AQ | PILLS |
| FM | PINT, IMPERIAL MEASURE |
| FL | PINT, US MEASURE |
| AR | PINTS |
| JW | POLLEN UNITS |
| KA | PORTIONS |
| AS | POUNDS |
| GR | POUNDS OF WATER |
| HW | POUNDS OF WATER PER HOUR |
| EG | POUNDS PER 100 SQUARE FEET |
| JD | POUNDS PER ACRE |
| DA | POUNDS PER CUBIC FOOT |
| EN | POUNDS PER DAY |
| CZ | POUNDS PER FOOT |
| EP | POUNDS PER HOUR |
| CM | POUNDS PER INCH |
| EC | POUNDS PER MINUTE |
| CW | POUNDS PER SQUARE FOOT |
| FB | POUNDS PER SQUARE INCH |
| LZ | POUNDS PER SQUARE INCH ABSOLUTE |
| MA | POUNDS PER SQUARE INCH DIFFERENTIAL |
| JS | POUNDS PER SQUARE INCH GAGE |
| MB | POUNDS PER SQUARE INCH VACUUM |
| ED | POUNDS PER SQUARE YARD |
| CS | POUNDS PER YARD |
| JX | PROTEIN NITROGEN UNITS |
| FP | QUART, IMPERIAL MEASURE |
| FN | QUART, US MEASURE |
| AT | QUARTS |
| HF | QUARTS PER HOUR |
| JM | RECIPROCAL ERGS PER SQ CM |
| JN | RECIPROCAL ROENTGENS |
| FC | REVOLUTIONS PER MINUTE |
| FD | REVOLUTIONS PER SECOND |
| BN | ROLL |
| DK | SECONDS |
| BD | SHEET |
| HM | SHEETS |
| KP | SPONGE |
| DE | SQUARE CENTIMETERS |
| DQ | SQUARE FEET |
| DD | SQUARE INCHES |
| HJ | SQUARE INCHES PER POUND |
| EL | SQUARE METERS |
| GN | SQUARE MILLIMETERS |
| HK | SQUARE MILLIMETERS PER KILOGRAM |
| AV | STRIP |
| AW | SUPPOSITORIES |
| BP | SWAB |
| LK | TABLESPOON |
| AX | TABLETS |
| MY | TABS |
| GF | TANK |
| LL | TEASPOON |
| CU | TERABYTES |
| LY | TESTS |
| DT | THOUSANDTHS OF A FOOT |
| DW | THOUSANDTHS OF A METER |
| BY | TONS |
| EQ | TONS PER DAY |
| FF | TONS PER HOUR |
| NB | TORR |
| BQ | TRAY |
| AY | TROCHE |
| KD | TROOP |
| KF | TUBES |
| CL | TURNS |
| AZ | UNITS |
| MS | US TEST UNITS |
| BV | USP UNITS |
| NA | VOLT |
| MZ | VOLTAGE DIRECT CURRENT |
| HZ | VOLUMETRIC |
| LA | WEBERS PER SQUARE METER |
| BR | YARD, ROLL |
| BE | YARDS |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJLB2.0*;ABKWJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| K | KELVIN |
BKFB*JEXTERNAL DC OPERATING VOLTAGE IN VOLTS
THE VALUE(S) OF THE POTENTIAL SUPPLIED FROM AN EXTERIOR DIRECT CURRENT SOURCE TO OPERATE THE ITEM,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BKFBJAAC2.0*;BKFBJAAC2.0$$JAAC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 2 |
| Reply Code (AD88) | Reply |
| AC | 1ST VOLTAGE |
| AD | 2ND VOLTAGE |
| AA | SINGLE VOLTAGE |
BKFC*JEXTERNAL AC OPERATING VOLTAGE IN VOLTS
THE VALUE(S) OF THE POTENTIAL SUPPLIED FROM AN EXTERIOR ALTERNATING CURRENT SOURCE TO OPERATE THE ITEM,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BKFCJAAA2.0*;BKFCJAAA2.0$$JAAA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 2 |
| Reply Code (AD88) | Reply |
| AC | 1ST VOLTAGE |
| AD | 2ND VOLTAGE |
| AA | SINGLE VOLTAGE |
ANPL*JINPUT FREQUENCY RATING IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE INPUT ALTERNATING CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANPLJB2.0*;ANPLJB2.0$$JB2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASSB*AMECHANICAL CONNECTION QUANTITY
THE NUMBER OF MECHANICAL CONNECTIONS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ASSBA10*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
ASSC*GMECHANICAL CONNECTION SIZE
DESIGNATES THE THREAD SIZE,DIAMETER,OR THE LIKE,OF THE MECHANICAL CONNECTION.
Enter clear text.
(ASSCGCLEARTEXT)
ASSD*DMECHANICAL CONNECTION TYPE
INDICATES THE TYPE OF MECHANICAL CONNECTION/S/ PROVIDED.
Enter the applicable reply code from the table below
(ASSDDACD*;ASSDDACM$DABR*)
| Table 1 |
| Reply Code (AJ68) | Reply |
| ACD | BOSS |
| AED | EXTERNAL THREAD |
| ABF | FLANGE |
| ACM | INTERNAL STRAIGHT THREAD |
| ABR | SCREW |
| AEK | THREADED MALE FLARED TUBE |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDABW*;ADZCDABE$$DAAE*)
| Table 1 |
| Reply Code (AA65) | Reply |
| ADG | DRIP TIGHT |
| AAE | DUSTPROOF |
| AAT | MOISTURE PROOF |
| AAY | OIL TIGHT |
| AAZ | PRESSURE PROOF |
| ABE | SHOCK RESISTANT |
| ABR | SPLASH PROOF |
| ABW | SUBMERSIBLE |
| AHC | VIBRATION |
| ABL | WATERTIGHT |
| ABM | WEATHERPROOF |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ATJB*JWEIGHING CAPACITY
THE WEIGHING CAPACITY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ATJBJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BA | GRAMS |
| AJ | KILOGRAMS |
| AL | MILLIGRAMS |
BHYN*JVERNIER SCALE MEASUREMENT RESOLUTION
THE RESOLVED MEASUREMENT OF A VERNIER SCALE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BHYNJK2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| G | KILOGRAMS |
| K | KILOMETERS |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information