Table 1
	Reply Code (AM39)	Reply
	ABH	CLAMP
	AFL	CLIP
	ABY	SLOT
	ACD	TERMINAL
	AFA	THREADED BUSHING
	AJZ	THREADED BUSHING WITH PANEL SEAL
	AHF	THREADED HOLE(S)
	AET	THREADED STUD(S)
	ACQ	UNTHREADED HOLE(S)

IF STYLE/REPLY CODE(s) EM, MJ, SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CTTC) or (CQJX and CQQR) or (CQJX and AAJE)

IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX)

IF STYLE/REPLY CODE(s) JS, NJ, NS OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP)

IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX and CQQR)

THSD*DTHREAD SERIES DESIGNATOR

A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.

Enter the applicable reply code from the table below

(THSDDJE*;THSDDNF$$DJC*)

Table 1
	Reply Code (AH06)	Reply
	SM	ISO M
	SS	ISO S
	EM	M
	MJ	MJ
	UN	UN
	NE	UNEF
	NF	UNF
	NC	UNIFIED NATIONAL COARSE (UNC)
	NJ	UNIFIED NATIONAL JOINT (UNJ)
	JF	UNIFIED NATIONAL JOINT FINE (UNJF)
	JC	UNJC
	JE	UNJEF
	JS	UNJS
	NM	UNM
	NS	UNS

CQJX*JNOMINAL THREAD SIZE

A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CQJXJA2.0*;CQJXJA2.0$$JA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

CTTC*JTHREAD TOLERANCE CLASS

A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.

Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.

(CTTCJNTE2.0*;CTTCJNTE2.0$$JNTE2.1*)

Table 1
	Reply Code (AN73)	Reply
	EXT	EXTERNAL
	NTE	INTERNAL

CMLP*ATHREAD QUANTITY PER INCH

THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.

Enter the alpha-numeric reply with a minimum of one character.

(CMLPAB4)

CQQR*BTHREAD PITCH IN MILLIMETERS

A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(CQQRB2.0*;CQQRB2.0$$BM2.0*)

AAJE*JTHREAD PITCH DIAMETERS

THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.

(AAJEJAM32.0/P50.0*;AAJEJAM32.0/P50.0$$JA*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

AEBV*JUNTHREADED MOUNTING HOLE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEBVJAB2.0*;AEBVJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABTD*JMOUNTING SLOT WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABTDJAB2.0*;ABTDJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

CPRT*JMANUAL ACTUATOR TYPE AND QUANTITY

INDICATES THE TYPE AND NUMBER OF ACTUATORS PROVIDED FOR MANUAL CONTROL.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.

(CPRTJAAHZ2*;CPRTJAAHZ2$$JAAHZ3*;CPRTJAAHZ2$JAAHZ2*)

Table 1
	Reply Code (AC58)	Reply
	AAEW	PUSH BUTTON
	AAHZ	PUSH-PULL
	AAHX	ROTARY
	AAHY	TOGGLE

CPRW*DACTUATOR FUNCTION

DENOTES THE ACTION IMPARTED BY ACTUATOR OPERATION.

Enter the applicable reply code from the table below

(CPRWDBZ*;CPRWDBY$DCA*;CPRWDBY$$DCA*)

Table 1
	Reply Code (AE74)	Reply
	BY	RESET
	CA	TRIP W/SEPARATE RESET
	BZ	TRIP-RESET

CPRX*DACTUATOR POSITION DESIGNATION

AN INDICATION OF THE DESIGNATED POSITION OF THE ACTUATOR.

Enter the applicable reply code from the table below

(CPRXDEAR*;CPRXDEBA$$DEAS*)

Table 1
	Reply Code (AJ50)	Reply
	EAR	AT EACH POLE
	EAY	AT POLE FIVE
	EAX	AT POLE FOUR
	EAS	AT POLE ONE
	EAZ	AT POLE SIX
	EAW	AT POLE THREE
	EAT	AT POLE TWO
	EBE	BETWEEN POLE FIVE AND SIX
	EBD	BETWEEN POLE FOUR AND FIVE
	EBA	BETWEEN POLE ONE AND TWO
	EBC	BETWEEN POLE THREE AND FOUR
	EBB	BETWEEN POLE TWO AND THREE

CPRY*DEXTERNAL ACTUATOR LINKAGE ARRANGEMENT

INDICATES THE ARRANGEMENT OF THE EXTERNALLY CONNECTED ACTUATORS.

Enter the applicable reply code from the table below

(CPRYDBM*;CPRYDBW$$DBK*)

Table 1
	Reply Code (AH86)	Reply
	BN	FIVE AND SIX LINKED
	BM	FOUR AND FIVE LINKED
	BS	FOUR, FIVE, AND SIX LINKED
	BJ	ONE AND TWO LINKED
	BP	ONE, TWO, AND THREE LINKED
	BT	ONE, TWO, THREE, AND FOUR LINKED
	BY	ONE, TWO, THREE, FOUR, AND FIVE LINKED
	CA	ONE, TWO, THREE, FOUR, FIVE, AND SIX LINKED
	BL	THREE AND FOUR LINKED
	BR	THREE, FOUR, AND FIVE LINKED
	BX	THREE, FOUR, FIVE, AND SIX LINKED
	BK	TWO AND THREE LINKED
	BQ	TWO, THREE, AND FOUR LINKED
	BW	TWO, THREE, FOUR, AND FIVE LINKED
	BZ	TWO, THREE, FOUR, FIVE, AND SIX LINKED

TTQYJTERMINAL TYPE AND QUANTITY

INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.

(TTQYJAEC2*;TTQYJAEC2$$JAEC3*;TTQYJAEC2$JAEC2*)

Table 1
	Reply Code (AN89)	Reply
	AEM	BUS BAR
	ADB	CLIP
	AEB	COMPRESSION
	AFJ	DOUBLE SCREW
	ABR	EYELET
	AEC	KNIFE BLADE
	AAM	PIN
	ADA	QUICK DISCONNECT, FEMALE
	ACZ	QUICK DISCONNECT, MALE
	ABQ	SCREW
	ABT	SCREW BASE
	AAS	SOLDER STUD
	AJJ	STAB
	ABX	TAB W/SCREW
	ABB	TAB, SOLDER LUG
	ABD	THREADED STUD
	ACB	TURRET
	ACM	WIRE HOOK
	ACC	WIRE LEAD

CPRZ*JAUXILIARY SWITCH FUNCTION AND QUANTITY

THE FUNCTION FOR WHICH THE AUXILIARY SWITCH IS DESIGNED AND THE NUMBER PROVIDED.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.

(CPRZJCC2*)

Table 1
	Reply Code (AE74)	Reply
	CB	ALARM
	CC	CONTROL

CQSM*HSWITCH LOCATION AND POSITION DESIGNATION

INDICATES THE LOCATION OF THE SWITCH IN RELATION TO ITS DESIGNATED POSITION.

Enter the applicable Reply Code from Tables 1 & 2 below.

(CQSMHNTEEAT2.0*;CQSMHNTEEAT2.0$$HNTEEAT2.1*)

Table 1
	Reply Code (AN73)	Reply
	EXT	EXTERNAL
	NTE	INTERNAL

Table 2
	Reply Code (AJ50)	Reply
	EAR	AT EACH POLE
	EAY	AT POLE FIVE
	EAX	AT POLE FOUR
	EAS	AT POLE ONE
	EAZ	AT POLE SIX
	EAW	AT POLE THREE
	EAT	AT POLE TWO
	EBE	BETWEEN POLE FIVE AND SIX
	EBD	BETWEEN POLE FOUR AND FIVE
	EBA	BETWEEN POLE ONE AND TWO
	EBC	BETWEEN POLE THREE AND FOUR
	EBB	BETWEEN POLE TWO AND THREE

AEGJ*DSWITCH CONTACT ARRANGEMENT

A DESIGNATION THAT DESCRIBES THE BASIC ELECTRICAL CONFIGURATION OF A SWITCH.

Enter the applicable reply code from the table below

(AEGJDCK*;AEGJDBG$$DBD*)

Table 1
	Reply Code (AD85)	Reply
	BF	DOUBLE POLE, DOUBLE THROW
	BE	DOUBLE POLE, SINGLE THROW, NORMALLY CLOSED
	BD	DOUBLE POLE, SINGLE THROW, NORMALLY OPEN
	CK	SINGLE POLE, DOUBLE THROW
	BG	SINGLE POLE, SINGLE THROW, NORMALLY CLOSED
	CN	SINGLE POLE, SINGLE THROW, NORMALLY OPEN

CSSX*JSWITCH CURRENT RATING AND TYPE IN AMPS

THE AMOUNT OF CURRENT,EXPRESSED IN AMPERES,AND THE TYPE FOR WHICH THE SWITCH IS RATED.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CSSXJDC2.0*;CSSXJDC2.0$$JDC2.1*)

Table 1
	Reply Code (AN87)	Reply
	AC	AC
	DC	DC

CSWP*JSWITCH VOLTAGE RATING AND TYPE IN VOLTS

THE VOLTAGE,EXPRESSED IN VOLTS,AND CURRENT TYPE FOR WHICH THE SWITCH IS RATED.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CSWPJDC2.0*;CSWPJDC2.0$$JDC2.1*)

Table 1
	Reply Code (AN87)	Reply
	AC	AC
	DC	DC

CRTK*DSWITCH TERMINAL TYPE

INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE SWITCH.

Enter the applicable reply code from the table below

(CRTKDADA*;CRTKDABD$$DAEB*)

Table 1
	Reply Code (AN89)	Reply
	AEM	BUS BAR
	ADB	CLIP
	AEB	COMPRESSION
	AFJ	DOUBLE SCREW
	ABR	EYELET
	AEC	KNIFE BLADE
	AAM	PIN
	ADA	QUICK DISCONNECT, FEMALE
	ACZ	QUICK DISCONNECT, MALE
	ABQ	SCREW
	ABT	SCREW BASE
	AAS	SOLDER STUD
	AJJ	STAB
	ABX	TAB W/SCREW
	ABB	TAB, SOLDER LUG
	ABD	THREADED STUD
	ACB	TURRET
	ACM	WIRE HOOK
	ACC	WIRE LEAD

CQXF*DINCLOSURE PROTECTION TYPE FOR WHICH DESIGNED

INDICATES THE TYPE OF PROTECTION FOR WHICH THE INCLOSURE IS DESIGNED.

Enter the applicable reply code from the table below

(CQXFDAAY*;CQXFDABT$$DABD*)

Table 1
	Reply Code (AP30)	Reply
	AAX	ARC RESISTANT
	AAY	COMBUSTION PROOF
	AAZ	CORROSION RESISTANT
	ABA	DRIPPROOF
	ABB	DUSTPROOF
	ABC	DUSTTIGHT
	ABD	EXPLOSION PROOF
	ABE	EXPLOSION RESISTANT
	ABF	FLAME RESISTANT
	ABG	FUNGUS PROOF
	ABH	FUNGUS RESISTANT
	ABJ	GENERAL PURPOSE
	ABK	HERMETICALLY SEALED
	ABL	HUMIDITY PROOF
	ABM	HUMIDITY RESISTANT
	ABP	MOISTURE PROOF
	ABN	MOISTURE RESISTANT
	AAQ	OIL RESISTANT
	ABQ	OILTIGHT
	ABR	RAINTIGHT
	ABS	SALT SPRAY PROOF
	ABT	SALT WATER RESISTANT
	ABX	SAND RESISTANT
	ABW	SANDTIGHT
	ABZ	SHOCK RESISTANT
	ABY	SHOCKPROOF
	ACA	SPLASHPROOF
	ACB	TAMPERPROOF
	ACC	VAPORTIGHT
	ACE	VIBRATION RESISTANT
	ACD	VIBRATIONPROOF
	ACF	WATER RESISTANT
	AAS	WATERPROOF
	ACG	WATERTIGHT
	ACH	WEATHERPROOF

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDAPN*;CBBLDAPM$$DAPF*)

Table 1
	Reply Code (AN47)	Reply
	APE	ADJUSTABLE TRIP RELEASE
	APF	CURRENT LIMITER
	APG	CURRENT LIMITER ACCOMMODATION
	APT	GROUND FAULT PROTECTION
	APH	HANDLE LOCK
	BQG	HIGH INRUSH PROTECTION
	APJ	INTERCHANGEABLE TRIP RELEASE
	APK	KEY INTERLOCK
	APL	NEUTRAL POLE, GROUNDED
	APM	NEUTRAL POLE, INSULATED-GROUNDABLE
	APN	NEUTRAL POLE, SWITCHABLE
	APP	OFFSET HANDLE EXTENSION
	APQ	PADLOCK ATTACHMENT
	APR	SLIDING BAR INTERLOCK
	CCZ	TRIP INDICATOR
	APS	WALKING BEAM INTERLOCK

IF STYLE/REPLY CODE(s) P WERE ENTERED FOR MRC RADC, YOU MUST ANSWER MRC (RADD)

RADC*DRADIOACTIVE CONTENT

AN INDICATION OF WHETHER OR NOT THE ITEM CONTAINS RADIOACTIVE MATERIALS.

Enter the applicable reply code from the table below

(RADCDP)

Table 1
	Reply Code (AN54)	Reply
	P	CONTAINS RADIOACTIVE MATERIAL

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE

AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.

Enter the applicable reply code from the table below

(NHCFDCY)

Table 1
	Reply Code (AD05)	Reply
	CY	HARDENED

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)

Table 1
	Reply Code (AN58)	Reply
	A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

APNQ*DARC QUENCHING METHOD

THE MEANS OF QUENCHING AN ARC.

Enter the applicable reply code from the table below

(APNQDAJ)

Table 1
	Reply Code (AK63)	Reply
	AB	AIR
	AH	AIR BLAST
	AJ	DEION
	AK	MAGNETIC BLOWOUT
	AL	OIL BLOWOUT

AEFP*JNONTURN DEVICE RADIUS

THE LINEAR MEASUREMENT OF THE DISTANCE FROM THE ACTUATOR CENTERLINE TO THE CENTERLINE OF THE NONTURN DEVICE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEFPJAA2.0*;AEFPJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEFQ*JNONTURN DEVICE LENGTH

THE MEASUREMENT OF THE DISTANCE THAT THE NONTURN DEVICE PROTRUDES ABOVE THE MOUNTING SURFACE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEFQJAA2.0*;AEFQJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEFR*JNONTURN DEVICE WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A NONTURN DEVICE,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEFRJAB2.0*;AEFRJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEFS*JNONTURN DEVICE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NONTURN DEVICE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEFSJAC2.0*;AEFSJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BBRG*DSTORAGE TYPE

INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.

Enter the applicable reply code from the table below

(BBRGDA*;BBRGDAE$DAG*)

Table 1
	Reply Code (AM81)	Reply
	AB	ABOVE GROUND MAGAZINE
	A	ANY ACCEPTABLE
	AC	CLOSED SHED
	AM	DEHUMIDIFIED WAREHOUSE
	AT	DOCK LEVEL HEATED WAREHOUSE
	AX	DOCK LEVEL UNHEATED WAREHOUSE
	AE	GENERAL PURPOSE WAREHOUSE
	AS	GROUND LEVEL HEATED WAREHOUSE
	AW	GROUND LEVEL UNHEATED WAREHOUSE
	AN	HEATED WAREHOUSE
	AF	IGLOO MAGAZINE
	AG	IMPROVED OPEN
	AH	OPEN SHED
	AR	SHED
	AJ	UNHEATED WAREHOUSE
	AK	UNIMPROVED OPEN