Several disks stacked to form a heatsink. Half of the disks are keyed to rotate with the wheel alternated with nonrotating disks keyed to an anchor bracket. It is a component of a BRAKE,MULTIPLE DISK or a BRAKE,SEGMENTED ROTOR. All except USA Removed on 2/7/2020.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED68077*)
Reply to this MRC in accordance with Volume 3.
AGAVGEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ALBY*DUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDABZ)
| Table 1 |
| Reply Code (AH21) | Reply |
| AHX | AIRCRAFT |
| BPX | COMBAT VEHICLE |
| BDM | FIRE FIGHTING TRUCK |
| BGH | FULL-TRACKED VEHICLE |
| AGQ | GENERATOR |
| BTE | MISSLE SYSTEMS |
| AMJ | SEMITRAILER |
| AHY | SHIP |
| ACA | SUBMARINE |
| ABY | TRAILER |
| ABZ | TRUCK |
| AMF | VEHICULAR |
| BTB | WINCH |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDST1092*;MATTDRCB000$DST1068*;MATTDRCB000$$DST1068*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL5052 | ALUMINUM ALLOY 5052 |
| ZSU000 | ALUMINUM ALLOY 5059 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL6061 | ALUMINUM ALLOY 6061 |
| CUB000 | COPPER ALLOY |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| FEJ000 | IRON DUCTILE |
| PCA000 | PLASTIC |
| RCE000 | RUBBER |
| RCB000 | RUBBER SYNTHETIC |
| STA000 | STEEL |
| ST1035 | STEEL COMP 1035 |
| ST1036 | STEEL COMP 1036 |
| ST1037 | STEEL COMP 1037 |
| ST1038 | STEEL COMP 1038 |
| ST1039 | STEEL COMP 1039 |
| ST1040 | STEEL COMP 1040 |
| ST1041 | STEEL COMP 1041 |
| ST1042 | STEEL COMP 1042 |
| ST1043 | STEEL COMP 1043 |
| ST1044 | STEEL COMP 1044 |
| ST1045 | STEEL COMP 1045 |
| ST1046 | STEEL COMP 1046 |
| ST1048 | STEEL COMP 1048 |
| ST1049 | STEEL COMP 1049 |
| ST1050 | STEEL COMP 1050 |
| ST1051 | STEEL COMP 1051 |
| ST1052 | STEEL COMP 1052 |
| ST1053 | STEEL COMP 1053 |
| ST1054 | STEEL COMP 1054 |
| ST1055 | STEEL COMP 1055 |
| ST1059 | STEEL COMP 1059 |
| ST1060 | STEEL COMP 1060 |
| ST1061 | STEEL COMP 1061 |
| ST1062 | STEEL COMP 1062 |
| ST1064 | STEEL COMP 1064 |
| ST1065 | STEEL COMP 1065 |
| ST1066 | STEEL COMP 1066 |
| ST1069 | STEEL COMP 1069 |
| ST1070 | STEEL COMP 1070 |
| ST1071 | STEEL COMP 1071 |
| ST1072 | STEEL COMP 1072 |
| ST1074 | STEEL COMP 1074 |
| ST1075 | STEEL COMP 1075 |
| ST1078 | STEEL COMP 1078 |
| ST1080 | STEEL COMP 1080 |
| ST1084 | STEEL COMP 1084 |
| ST1085 | STEEL COMP 1085 |
| ST1086 | STEEL COMP 1086 |
| ST1090 | STEEL COMP 1090 |
| ST1095 | STEEL COMP 1095 |
| ST0303 | STEEL COMP 303 |
| ST0304 | STEEL COMP 304 |
| ST1094 | STEEL COMP 410S |
| ST4140 | STEEL COMP 4140 |
| ST1047 | STEEL COMP 422 |
| ST4340 | STEEL COMP 4340 |
| ST1093 | STEEL COMP E3316 |
| STB000 | STEEL CORROSION RESISTING |
| ST1092 | STEEL UNS J11442 |
| ST1089 | STEEL UNS J91309 |
| ST1091 | STEEL UNS J91459 |
| ST1067 | STEEL UNS K11547 |
| ST1081 | STEEL UNS K11562 |
| ST1079 | STEEL UNS K11597 |
| ST1082 | STEEL UNS K12047 |
| ST1057 | STEEL UNS K14072 |
| ST1068 | STEEL UNS K21509 |
| ST1076 | STEEL UNS K41245 |
| ST1073 | STEEL UNS K51545 |
| ST1058 | STEEL UNS S33100 |
| ST1063 | STEEL UNS S34809 |
| ST1083 | STEEL UNS T12001 |
| ST1087 | STEEL UNS T12002 |
| ST1088 | STEEL UNS T12005 |
| STF000 | STEEL,CARBON |
CYHX*AVEHICLE DESIGN CONTROL ACTIVITY
THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE VEHICLE.
Enter the alpha-numeric reply with five character(s) exactly.
(CYHXAM0L4Q)
CYHY*AVEHICLE IDENTIFICATION DESIGNATOR
THE NAME OR COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC VEHICLE.
Enter the alpha-numeric reply with a minimum of one character.
(CYHYAV5)
CYHZ*AVEHICLE YEAR(S)
THE FOUR (4) DIGIT NUMBER INDICATING THE PRODUCTION YEAR(S) OF THE VEHICLE.
Enter the alpha-numeric reply with a minimum of one character.
(CYHZAO2)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAS0)
CYPT*ASERIES AND/OR SERIAL NUMBER FOR WHICH DESIGNED
THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED SERIES/SERIAL NUMBER OF THE UNIT FOR WHICH THE ITEM IS DESIGNED.
Enter the alpha-numeric reply with a minimum of one character.
(CYPTAM5)
AFZC*DFUNCTION FOR WHICH DESIGNED
THE SPECIFIC PURPOSE FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AFZCDBU)
| Table 1 |
| Reply Code (AE74) | Reply |
| AU | EMERGENCY BRAKING |
| AM | GENERAL PURPOSE |
| BU | PARKING BRAKING |
| BV | SERVICE BRAKING |
| AV | SWITCHING |
TMQY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TMQYJBQG2*;TMQYJBQG2$$JBQG3*)
| Table 1 |
| Reply Code (AB28) | Reply |
| ABR | BOLT |
| ABS | BRACKET |
| AEL | CAP |
| BWQ | DIPSTICK CAP |
| AZA | FILTER |
| ACN | GASKET |
| AJR | INSERT |
| ABW | NUT |
| ABY | PIN |
| BCW | ROD |
| ACW | SIGHT GAGE |
| BQG | TUBE |
| AJW | WASHER |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDERH*;CBBLDERK$$DERJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| ERG | FLANGED END |
| ERH | FRONT DISC BRAKE DESIGN |
| DES | LEFT HAND |
| ERJ | PISTON TYPE SPRING BRAKE |
| ERK | REAR DISC BRAKE DESIGN |
| DFG | RIGHT HAND |
| ERL | WEDGE TYPE SPRING BRAKE |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAA2.0*;ADAVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJLC2.0*;ABTBJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXV*JBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXVJAC2.0*;ABXVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACHY*DMOUNTING HOLE TYPE
INDICATES THE TYPE OF HOLES PROVIDED IN THE ITEM TO FACILITATE MOUNTING TO ANOTHER ITEM.
Enter the applicable reply code from the table below
(ACHYDD)
| Table 1 |
| Reply Code (AB68) | Reply |
| A | COUNTERBORED |
| B | COUNTERSUNK |
| C | PLAIN |
| P | SLOTTED |
| D | THREADED |
| U | THRU HOLE |
| E | UNTHREADED |
ACUN*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM. THIS MRC IS BEING DISCONTINUED. PLEASE USE MRC AXGY IF AVAILABLE.
Enter the applicable reply code from the table below
(ACUNDACJ)
| Table 1 |
| Reply Code (AB89) | Reply |
| APP | BOLTED |
| AAH | RIVETED |
| ACJ | SCREW |
AFGA*JOPERATING TEMP RANGE
THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFGAJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AGJS*JPITCH DIAMETER
A MEASUREMENT INDICATING THE DIAMETER-PITCH PER SPECIFIC MEASUREMENT SCALE OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGJSJAC2.0*;AGJSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJLA*ATEETH QUANTITY
THE NUMBER OF TEETH INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJLAA10*)
AJJW*ACOMPONENT QUANTITY
THE NUMBER OF COMPONENTS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJJWA10*)
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
CQFM*JHARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQFMJRAA2.0*)
| Table 1 |
| Reply Code (AC26) | Reply |
| BN | BRINELL |
| RA | ROCKWELL A |
| RB | ROCKWELL B |
| RC | ROCKWELL C |
| RD | ROCKWELL D |
| RE | ROCKWELL E |
| RQ | ROCKWELL H |
| SA | SHORE DUROMETER A |
| SB | SHORE DUROMETER B |
| SE | SHORE DUROMETER C |
| SD | SHORE DUROMETER D |
| SC | SHORE SCLEROSCOPE |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQQF*JOPERATING PRESSURE
THE PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQQFJMAB2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| LM | BAR |
| FB | POUNDS PER SQUARE INCH |
| MA | POUNDS PER SQUARE INCH DIFFERENTIAL |
| JS | POUNDS PER SQUARE INCH GAGE |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDTA0099)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| GY0000 | GRAY/GREY |
| TA0000 | TAN |
| TA0099 | TAN, 686A |
AXYS*DSPLINE TYPE
INDICATES THE TYPE OF SPLINE PROVIDED.
Enter the applicable reply code from the table below
(AXYSDBM)
| Table 1 |
| Reply Code (AA85) | Reply |
| BE | EXTERNAL INVOLUTE |
| BF | EXTERNAL STRAIGHT |
| BG | INTERNAL INVOLUTE |
| BH | INTERNAL STRAIGHT |
| BS | INVOLUTE |
| BM | THREADED |
AMWN*AMODEL NUMBER
THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(AMWNAB3)
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJAA2.0*;ADUMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEQC*BOPERATING SPEED AT RATED CAPACITY IN RPM
THE SPEED OF THE DRIVE SHAFT REQUIRED TO PRODUCE THE RATED CAPACITY OF AN ITEM,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEQCB2.0)
AJJX*DCOMPONENT DOCUMENT ORIGIN
THE ORIGINATOR /GOVERNMENTAL,INDUSTRIAL,OR OTHERWISE/ OF THE AVAILABLE DOCUMENT WHICH LISTS THE COMPONENT/S/ OF THE ITEM.
Enter the applicable reply code from the table below
(AJJXDAD)
| Table 1 |
| Reply Code (AF59) | Reply |
| AF | GOVERNMENT |
| AD | INDUSTRIAL |
AJJZ*DDOCUMENT TYPE
INDICATES THE TYPE OF DOCUMENT BY THE TITLE.
Enter the applicable reply code from the table below
(AJJZDAG)
| Table 1 |
| Reply Code (AF70) | Reply |
| BE | CATALOG SHEET |
| BK | INDUSTRIAL DRAWING |
| BN | MILITARY DRAWING |
| BT | PARTS LIST |
| FE | SOURCE CONTROL DRAWING |
| AB | TECHNICAL MANUAL |
| AG | TECHNICAL ORDER |
BBJX*DMOUNTING POSITION
THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BBJXDAAW)
| Table 1 |
| Reply Code (AM84) | Reply |
| ACH | LEFT FRONT |
| AFJ | LEFT REAR |
| ACK | RIGHT FRONT |
| AFK | RIGHT REAR |
| AAW | UNIVERSAL |
HEAT*DHEAT TREATMENT
A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM.
Enter the applicable reply code from the table below
(HEATDCR)
| Table 1 |
| Reply Code (AD05) | Reply |
| BP | ANNEALED |
| CZ | CASEHARDENED |
| CR | COLD DRAWN |
| CX | COLD ROLLED |
| CU | EXTRUDED |
| EX | H-111 STRAIN HARDENED |
| GB | H-116 SPECIALLY TREATED |
| TP | H-24 STRAIN HARDENED, PARTIALLY ANNEALED TO 1/2 HARD |
| TQ | H-32 STRAIN HARDENED, STABILIZED TO 1/4 HARD |
| QP | H-321 STRAIN HARDENED |
| LL | H-323 STRAIN HARDENED AND STABILIZED |
| TR | H-34 STRAIN HARDENED, STABILIZED TO 1/2 HARD |
| TS | H-36 STRAIN HARDENED, STABILIZED TO 3/4 HARD |
| TT | H-38 STRAIN HARDENED, STABILIZED TO FULL HARD |
| CH | HARD |
| CY | HARDENED |
| CT | HOT ROLLED |
| JR | OILED |
| JQ | PICKLED |
| EN | QUENCHED |
| JT | ROLLED |
| DZ | T-52 COOLED STRESS RELIEVED AND ARTIFICALLY AGED |
| TW | T-6 SOLUTION HEAT TREATED, ARTIFICALLY AGED |
| RX | T-651 SOLUTION HEAT TREATED, ARTIFICALLY AGED, AND STRESS RELIEVED BY STRETCHING |
| RK | T-6510 SOLUTION HEAT TREATED |
| RL | T-6511 SOLUTION HEAT TREATED |
| EP | TEMPERED |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
MEDA*DMEDIA FOR WHICH DESIGNED
THE TYPE OF MEDIA FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(MEDADAAQ)
| Table 1 |
| Reply Code (AN91) | Reply |
| ABH | BRAKE FLUID, NONMINERAL OIL |
| AAQ | GAS |
| AAR | GREASE |
| AGT | HYDRAULIC FLUID, MINERAL BASE |
| AAT | HYDRAULIC FLUID, WATER BASE |
| ACE | OIL, HYDRAULIC |
| ADE | OIL, LUBRICATING |
| AGG | OIL, MINERAL |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDCDC000*;SFTTDANA000$DPRA001*;SFTTDANA000$$DPRA001*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDC000 | CADMIUM PLATED |
| AAA000 | PAINTED |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PHD000 | PHOSPHATE ZINC |
| PRA000 | PRIMER |
| PRF000 | PRIMER EPOXY |
| PRA001 | PRIMER EPOXY-LEAD AND CHROMIUM FREE |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information