A resistor whose ohmic value cannot be adjusted or varied.The resistor element consists of either a thin layer or conductive material, containing neither binders or insulating materials, deposited on an insulated form, or an alloy of metal and ceramic materials, usually fused to an insulated form.Opposition to the flow of current is an inherent property of the materials used and is manifest by the heat dissipation in the resistor.Primarily intended for incorporation into microelectronic circuits and surface mounted applications.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED67164*)
AAPPJELECTRICAL RESISTANCE
A MEASURE OF THE OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAPPJQ2.0*)
| Table 1 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
AAPQFRESISTANCE TOLERANCE IN PERCENT
THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AAPQFM2.0/P4.7*)
AEFBJPOWER DISSIPATION RATING IN WATTS
THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY AN ITEM,EXPRESSED IN WATTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFBJC2.0*)
| Table 1 |
| Reply Code (AC89) | Reply |
| B | FREE AIR |
| C | HEAT SINK |
AAQFBAMBIENT TEMP IN DEG CELSIUS AT FULL RATED POWER
THE AMBIENT TEMPERATURE OF THE MEDIUM SURROUNDING AN ITEM AT WHICH IT CAN BE OPERATED CONTINUOUSLY AT FULL RATED POWER,EXPRESSED IN DEGREES CELSIUS. PLEASE USE MRC AEHY IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAQFB2.0)
AAQGBAMBIENT TEMP IN DEG CELSIUS AT ZERO PERCENT RATED POWER
THE AMBIENT TEMPERATURE AT WHICH THE POWER DISSIPATION OF AN ITEM IS OPERATED TO ZERO PERCENT OF THE FULL RATED POWER,EXPRESSED IN DEGREES CELSIUS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAQGB2.0)
AAQZDINCLOSURE METHOD
THE MEANS PROVIDED TO COAT,COVER,OR PROTECT THE ITEM. PLEASE USE MRC AKNA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AAQZDA*;AAQZDD$DC*)
| Table 1 |
| Reply Code (AA59) | Reply |
| B | ENCAPSULATED |
| C | ENCASED |
| D | HERMETICALLY SEALED |
| A | UNINCLOSED |
AARBDTERMINAL TYPE
INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. PLEASE USE MRC CSCF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AARBDAN*;AARBDAW$DAT*;AARBDAW$$DAT*)
| Table 1 |
| Reply Code (AA58) | Reply |
| AB | BRACKET |
| AC | CLAMP |
| AF | EYELET |
| AJ | FERRULE |
| AK | FERRULE W/TAB |
| AL | FERRULE W/WIRE LEAD |
| FU | ONE SURFACE |
| AM | PIN |
| AN | SCREW BASE |
| AQ | SOLDER STUD |
| AU | TAB W/SCREW |
| AV | TAB W/WIRE LEAD |
| AW | TAB W/WIRE LEAD W/TAB |
| AT | TAB, SOLDER LUG |
| AX | TAPERED FERRULE |
| BD | TERMINAL TYPE PER BODY STYLE |
| AZ | THREADED STUD |
| BA | TURRET |
| XL | WIRE CLAMP |
| BB | WIRE LEAD |
| ET | WRAP AROUND |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) E WERE ENTERED FOR MRC AARG, YOU MUST ANSWER MRC (AARH)
AARGDRELIABILITY INDICATOR
AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.
Enter the applicable reply code from the table below
(AARGDN)
| Table 1 |
| Reply Code (AA61) | Reply |
| E | ESTABLISHED |
| N | NOT ESTABLISHED |
IF STYLE/REPLY CODE(s) 4, 5, 6, 7, 8, 1, 40, 52, 14, 15, 18, 20, 23, 25, 26, 27, 29, 30, 31, 37, 38, 43, 44, 45, 46, 47, 48, 50, 57, 58, 59, 60, 61, 63, 65, 66, 67, 73, 74, 75, 78, 81, 82, 85, 86, 87, 90, 91, 92, 93, 95, 97, 98, 99, 113, 116, 117, 119, 132, 100, 101, 102, 105, 106, 108, 109, 110, 121, 122, 123, 124, 126, 128, 141, 143, 146, 155, 159, 160, 161, 166, 167, 169, 172, 177, 193 OR 184 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ABPM)
IF STYLE/REPLY CODE(s) 10 OR 69 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ)
IF STYLE/REPLY CODE(s) 19, 71, 154, 156 OR 168 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ABPM and AEBY and BYML)
IF STYLE/REPLY CODE(s) 197 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU and ADAG)
IF STYLE/REPLY CODE(s) 144 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEBY and ADAT)
IF STYLE/REPLY CODE(s) 148 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and BYML and ADAT and AEBY and ADAU)
IF STYLE/REPLY CODE(s) 149, 151, 153, 157, 174 OR 183 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ABPM and AEBY)
IF STYLE/REPLY CODE(s) 140 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEBY and BYML and ADAT and AEHA)
IF STYLE/REPLY CODE(s) 178 OR 179 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ABPM and ADAP and AFYE)
IF STYLE/REPLY CODE(s) 34, 35, 70, 129, 135, 163 OR 173 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEBY and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 13, 21, 22, 24, 36, 103, 111, 137 OR 165 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT)
IF STYLE/REPLY CODE(s) 2, 28, 49, 68, 84, 88, 94, 107, 130, 139, 142, 152, 164, 170, 171, 194, 195, 196 OR 198 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 16, 62, 76, 77, 96, 104, 134, 136, 150, 162 OR 182 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEBY and BYML and ADAT and ADAU)
IF STYLE/REPLY CODE(s) 9, 53, 12, 79, 83, 127, 145 OR 181 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEBY and BYML and ADAT)
IF STYLE/REPLY CODE(s) 158 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAQ and AEBY and BYML and ADAT and ADAU and AEHA)
IF STYLE/REPLY CODE(s) 218, 219 OR 220 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAU and ADAQ and ADAT)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL100)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BO10048 | 1 | AXIAL TERMINAL EACH END |
| BO10010 | 10 | AXIAL TERMINAL EACH END |
| BO10035 | 100 | RADIAL TERMINALS |
| BO10024 | 101 | AXIAL TERMINALS ONE END |
| BO10032 | 102 | RADIAL TERMINAL EACH END |
| BO10129 | 103 | TERMINALS EACH END |
| BO10163 | 104 | TERMINALS ONE SIDE |
| BO10057 | 105 | AXIAL TERMINALS ONE END |
| BO10062 | 106 | AXIAL TERMINALS ONE END |
| BO10164 | 107 | TERMINALS ONE END |
| BO10101 | 108 | TERMINALS ONE END |
| BO10107 | 109 | RADIAL TERMINAL EACH END |
| BO10002 | 110 | AXIAL TERMINAL EACH END |
| BO10162 | 111 | TERMINALS ONE EDGE |
| BO10008 | 113 | RADIAL TERMINAL EACH END |
| BO10072 | 116 | RADIAL TERMINAL EACH END |
| BO10104 | 117 | AXIAL TERMINALS ONE END |
| BO10042 | 119 | AXIAL TERMINAL EACH END |
| BO10157 | 12 | TERMINALS ONE EDGE |
| BO10066 | 121 | RADIAL TERMINALS ONE END |
| BO10022 | 122 | RADIAL TERMINAL EACH END |
| BO10112 | 123 | AXIAL END TERMINATIONS, RADIAL TAP TERMINAL(S) |
| BO10091 | 124 | AXIAL TERMINAL EACH END |
| BO10110 | 126 | AXIAL END TERMINATIONS, RADIAL TAP TERMINAL(S) |
| BO10158 | 127 | TERMINALS ONE EDGE |
| BO10109 | 128 | AXIAL TERMINAL EACH END |
| BO10179 | 129 | TERMINALS ONE END |
| BO10160 | 13 | TERMINALS ONE EDGE |
| BO10151 | 130 | TERMINALS ONE END |
| BO10073 | 132 | RADIAL TERMINAL EACH END |
| BO10165 | 134 | TERMINALS ONE SIDE |
| BO10166 | 135 | TERMINALS ONE SIDE |
| BO10167 | 136 | TERMINALS ONE SIDE |
| BO10132 | 137 | TERMINALS EACH END |
| BO10144 | 139 | TERMINALS EACH END |
| BO10001 | 14 | AXIAL TERMINAL EACH END |
| BO10150 | 140 | TERMINALS ONE SIDE |
| BO10060 | 141 | RADIAL TERMINAL EACH END |
| BO10125 | 142 | TERMINALS ONE EDGE |
| BO10038 | 143 | AXIAL TERMINALS ONE END |
| BO10149 | 144 | TERMINALS ONE SIDE |
| BO10168 | 145 | TERMINALS ONE SIDE |
| BO10105 | 146 | AXIAL TERMINALS ONE END |
| BO10189 | 148 | AXIAL TERMINAL (S) |
| BO10098 | 149 | RADIAL TERMINALS |
| BO10111 | 15 | AXIAL TERMINAL EACH END |
| BO10187 | 150 | TERMINALS ONE SIDE |
| BO10040 | 151 | RADIAL TERMINAL EACH END |
| BO10130 | 152 | TERMINALS ONE END |
| BO10031 | 153 | RADIAL TERMINAL EACH END |
| BO10037 | 154 | RADIAL TERMINAL EACH END |
| BO10071 | 155 | RADIAL TERMINAL EACH END |
| BO10084 | 156 | AXIAL TERMINAL EACH END |
| BO10029 | 157 | RADIAL TERMINAL EACH END |
| BO10188 | 158 | TERMINALS ONE SIDE |
| BO10041 | 159 | AXIAL TERMINAL EACH END |
| BO10190 | 16 | TERMINALS ONE EDGE |
| BO10027 | 160 | RADIAL TERMINAL EACH END |
| BO10063 | 161 | RADIAL TERMINAL EACH END |
| BO10131 | 162 | TERMINALS ONE EDGE |
| BO10186 | 163 | TERMINALS ONE EDGE |
| BO10169 | 164 | TERMINALS EACH END |
| BO10170 | 165 | TERMINALS EACH END |
| BO10012 | 166 | AXIAL TERMINAL EACH END |
| BO10058 | 167 | RADIAL TERMINAL EACH END |
| BO10085 | 168 | AXIAL TERMINAL EACH END |
| BO10064 | 169 | RADIAL TERMINAL EACH END |
| BO10171 | 170 | TERMINALS EACH END |
| BO10172 | 171 | TERMINALS EACH END |
| BO10046 | 172 | RADIAL TERMINAL EACH END |
| BO10152 | 173 | TERMINALS EITHER END |
| BO10043 | 174 | AXIAL TERMINAL EACH END |
| BO10099 | 177 | AXIAL TERMINAL EACH END |
| BO10044 | 178 | AXIAL TERMINALS ONE END |
| BO10045 | 179 | AXIAL TERMINAL EACH END |
| BO10009 | 18 | RADIAL TERMINAL EACH END |
| BO10153 | 181 | TERMINALS ONE EDGE |
| BO10173 | 182 | TERMINALS EACH END |
| BO10069 | 183 | RADIAL TERMINAL EACH END |
| BO10011 | 184 | RADIAL TERMINAL EACH END |
| BO10051 | 19 | TERMINAL MOUNTED |
| BO10097 | 193 | CONCENTRIC TERMINATION PADS |
| BO10180 | 194 | TERMINAL EACH END |
| BO10181 | 195 | TERMINAL TWO SIDES |
| BO10182 | 196 | TERMINATION PAD EACH END |
| BO10183 | 197 | TERMINAL ONE END |
| BO10184 | 198 | TERMINATION PAD EACH END |
| BO10174 | 2 | TERMINALS ONE END |
| BO10070 | 20 | RADIAL TERMINAL EACH END |
| BO10159 | 21 | TERMINALS ONE EDGE |
| BO10191 | 218 | SINGLE INLINE |
| BO10192 | 219 | FLAT PACK |
| BO10161 | 22 | TERMINALS ONE EDGE |
| BO10193 | 220 | DUAL INLINE |
| BO10081 | 222 | RADIAL TERMINAL EACH END |
| BO10108 | 23 | RADIAL TERMINAL EACH END |
| BO10124 | 24 | TERMINALS ONE EDGE |
| BO10018 | 25 | RADIAL TERMINAL EACH END |
| BO10090 | 26 | AXIAL TERMINAL EACH END |
| BO10093 | 27 | AXIAL TERMINAL EACH END |
| BO10146 | 28 | TERMINALS ONE EDGE |
| BO10087 | 29 | AXIAL TERMINAL EACH END |
| BO10034 | 30 | RADIAL TERMINAL EACH END |
| BO10089 | 31 | AXIAL TERMINAL EACH END |
| BO10156 | 34 | TERMINALS ONE EDGE |
| BO10175 | 35 | TERMINALS ONE EDGE |
| BO10145 | 36 | TERMINALS ONE EDGE |
| BO10054 | 37 | RADIAL TERMINAL EACH END |
| BO10061 | 38 | RADIAL TERMINAL EACH END |
| BO10086 | 4 | AXIAL TERMINAL EACH END |
| BO10095 | 40 | AXIAL AND RADIAL TERMINALS |
| BO10096 | 43 | RADIAL TERMINALS |
| BO10049 | 44 | RADIAL TERMINAL EACH END |
| BO10003 | 45 | OPPOSING RADIAL TERMINALS EACH END |
| BO10056 | 46 | AXIAL TERMINALS ONE END |
| BO10023 | 47 | AXIAL TERMINALS ONE END |
| BO10004 | 48 | AXIAL TERMINALS ONE END |
| BO10126 | 49 | TERMINALS EACH END |
| BO10094 | 5 | SCREW BASE TERMINATION |
| BO10067 | 50 | RADIAL TERMINALS ONE END |
| BO10075 | 52 | RADIAL TERMINAL EACH END |
| BO10140 | 53 | TERMINALS EACH END |
| BO10016 | 57 | AXIAL TERMINAL EACH END |
| BO10055 | 58 | AXIAL TERMINAL EACH END |
| BO10030 | 59 | RADIAL TERMINAL EACH END |
| BO10065 | 6 | RADIAL TERMINAL EACH END |
| BO10005 | 60 | AXIAL TERMINALS ONE END |
| BO10103 | 61 | AXIAL TERMINALS ONE END |
| BO10139 | 62 | TERMINALS ONE EDGE |
| BO10020 | 63 | RADIAL TERMINAL EACH END |
| BO10092 | 65 | RADIAL TERMINAL EACH END |
| BO10007 | 66 | RADIAL TERMINAL EACH END |
| BO10052 | 67 | RADIAL TERMINAL EACH END |
| BO10155 | 68 | TERMINALS ONE SIDE |
| BO10127 | 69 | TERMINALS EACH END |
| BO10074 | 7 | RADIAL TERMINAL EACH END |
| BO10176 | 70 | TERMINALS ONE END |
| BO10050 | 71 | TERMINAL MOUNTED |
| BO10068 | 73 | RADIAL TERMINALS ONE END |
| BO10017 | 74 | RADIAL TERMINAL EACH END |
| BO10019 | 75 | RADIAL TERMINAL EACH END |
| BO10154 | 76 | TERMINALS EACH END |
| BO10141 | 77 | TERMINALS EACH END |
| BO10083 | 78 | AXIAL TERMINAL EACH END |
| BO10148 | 79 | TERMINALS ONE SIDE |
| BO10113 | 8 | AXIAL TERMINAL EACH END |
| BO10059 | 81 | RADIAL TERMINAL EACH END |
| BO10102 | 82 | AXIAL TERMINALS ONE END |
| BO10142 | 83 | TERMINALS EACH END |
| BO10143 | 84 | TERMINALS EACH END |
| BO10100 | 85 | CONCENTRIC TERMINALS |
| BO10053 | 86 | RADIAL TERMINAL EACH END |
| BO10106 | 87 | AXIAL TERMINAL EACH END |
| BO10177 | 88 | TERMINALS TWO EDGES |
| BO10147 | 9 | TERMINALS ONE SIDE |
| BO10036 | 90 | RADIAL TERMINAL EACH END |
| BO10025 | 91 | RADIAL TERMINALS ONE END |
| BO10006 | 92 | RADIAL TERMINALS |
| BO10033 | 93 | RADIAL TERMINALS ONE END |
| BO10178 | 94 | TERMINALS ONE END |
| BO10026 | 95 | AXIAL TERMINALS EACH END |
| BO10128 | 96 | TERMINALS ONE EDGE |
| BO10088 | 97 | AXIAL TERMINAL EACH END |
| BO10039 | 98 | RADIAL TERMINAL EACH END |
| BO10028 | 99 | AXIAL TERMINAL EACH END |
AAPE*FTEMP COEFFICIENT OF RESISTANCE IN PPM PER DEG CELSIUS
A CONSTANT THAT REPRESENTS THE PROPORTIONATE CHANGE IN RESISTANCE CAUSED BY A CHANGE IN TEMPERATURE,EXPRESSED IN PARTS PER MILLION CHANGE PER DEGREE CELSIUS.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AAPEFM2.0/P4.7*)
AAQH*FTEMP RANGE OF TEMP COEFFICIENT IN DEG CELSIUS
THE MAXIMUM AND MINIMUM TEMPERATURES TO WHICH THE TEMPERATURE COEFFICIENT APPLIES,EXPRESSED IN DEGREES CELSIUS.
Enter the range of numeric values with a minimum of one digit on both sides of the decimal. Separating range values with a slash and preceding negative values with an ‘M’ and positive values with a ‘P’.
(AAQHFM2.0/P4.7*)
ABPM*JBODY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPMJAC2.0*;ABPMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAG*JMOUNTING STUD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING STUD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAGJAB2.0*;ADAGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAP*JMOUNTING BUSHING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAPJAC2.0*;ADAPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAB2.0*;ADAQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAA2.0*;ADATJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAC2.0*;ADAUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBY*JDISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY LENGTH
THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE LENGTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBYJAA2.0*;AEBYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEHA*JDISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO BODY WIDTH
THE DISTANCE BETWEEN CENTERLINES OF MOUNTING FACILITIES PARALLEL TO THE WIDTH OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHAJAC2.0*;AEHAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYE*JMOUNTING BUSHING DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYEJAC2.0*;AFYEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYML*JMOUNTING HOLE SIZE
DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSION OF THE MOUNTING HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYMLJAC2.0*;BYMLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AARF*AMIL-STD-1276 WIRE LEAD TYPE DESIGNATOR
INDICATES THE TYPE DESIGNATOR,PER MIL-STD-1276,OF THE DETAIL REQUIREMENTS OF LEADS USED ON ELECTRONIC COMPONENTS.
Enter the alpha-numeric reply with a minimum of one character.
(AARFAE0)
AARH*BRELIABILITY FAILURE RATE LEVEL IN PERCENT
THE RATE OF FAILURE DETERMINED UNDER SPECIFIED CONDITIONS TO ESTABLISH THE RELIABILITY OF AN ITEM,EXPRESSED IN PERCENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AARHB2.0)
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAC2.0*;ABJTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFWW*JTERMINAL WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE TERMINAL,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFWWJAA2.0*;AFWWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBSZ*;CBBLDANY$$DAAJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BSZ | ELECTROSTATIC SENSITIVE |
| GJK | MOISTURE SENSITIVE |
| AAJ | MOUNTING HARDWARE |
| ANY | RADIOGRAPHICALLY INSPECTED |
| ANZ | RATED FOR CIRCUIT PROTECTION CAPABILITY |
| FNY | ROHS DIRECTIVE COMPLIANCE |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDQH*;ENACDAK$DQD*;ENACDAK$$DQD*)
| Table 1 |
| Reply Code (EN02) | Reply |
| QD | HEXAVALENT CHROMIUM ALTERNATIVE |
| AK | NON-CADMIUM PRODUCT |
| QH | NON-LEAD ALTERNATIVE PRODUCTS |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
AAQA*JHEAT SINK LENGTH
THE LARGEST DIMENSION OF A FLAT RECTANGULAR/ELLIPTICAL,OR A CHASSIS TYPE OF HEAT SINK.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQAJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAQB*JHEAT SINK WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLAT RECTANGULAR/ELLIPTICAL,OR CHASSIS TYPE HEAT SINK,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAQC*JHEAT SINK DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLAT DISK TYPE HEAT SINK,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQCJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAQD*JHEAT SINK HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A CHASSIS TYPE HEAT SINK,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQDJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAQE*JHEAT SINK THICKNESS
A MEASUREMENT OF THE SMALLEST PHYSICAL DIMENSION OF A HEAT SINK,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAQEJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PKWT*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PKWTJOZ2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| GM | GRAMS |
| KG | KILOGRAMS |
| OZ | OUNCES |
| LB | POUNDS |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAUA0002.0*;PMLCJAUA0002.0$JAUA0002.0*;PMLCJAUA0002.0$$JAUA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)