Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AAB1479	A1	PLAIN
AAB1488	A10	WEBBED OR SPOKED
AAB1489	A11	WEBBED OR SPOKED
AAB1490	A12	WEBBED OR SPOKED
AAB1491	A13	PLAIN
AAB1492	A14	WEBBED OR SPOKED
AAB1493	A15	WEBBED OR SPOKED
AAB1494	A16	WEBBED OR SPOKED
AAB1495	A17	WEBBED OR SPOKED
AAB1496	A18	WEBBED OR SPOKED
AAB1497	A19	WEBBED OR SPOKED
AAB1480	A2	PLAIN
AAB1498	A20	WEBBED OR SPOKED
AAB1499	A21	WEBBED OR SPOKED
AAB1500	A22	WEBBED OR SPOKED
AAB1501	A23	WEBBED OR SPOKED
AAB1502	A24	WEBBED OR SPOKED
AAB1503	A25	WEBBED OR SPOKED
AAB1504	A26	WEBBED OR SPOKED
AAB1505	A27	WEBBED OR SPOKED
AAB1506	A28	WEBBED OR SPOKED
AAB1481	A3	PLAIN
AAB1482	A4	WEBBED OR SPOKED
AAB1483	A5	WEBBED OR SPOKED
AAB1484	A6	WEBBED OR SPOKED
AAB1485	A7	WEBBED OR SPOKED
AAB1486	A8	WEBBED OR SPOKED
AAB1487	A9	WEBBED OR SPOKED

AAVL*JPILOT DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THAT PORTION USED TO GUIDE THE ITEM AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAVLJAB2.0*;AAVLJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABHE*JOUTSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHEJAA2.0*;ABHEJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABHP*JOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABKU*JFLANGE THICKNESS

A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABKUJAA2.0*;ABKUJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AGJS*JPITCH DIAMETER

A MEASUREMENT INDICATING THE DIAMETER-PITCH PER SPECIFIC MEASUREMENT SCALE OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AGJSJAA2.0*;AGJSJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AHTC*JFLANGE OUTSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AHTCJAB2.0*;AHTCJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AQPL*JFACE WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACE,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AQPLJAB2.0*;AQPLJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BYZG*JDISTANCE FROM PILOT END TO FLANGE FACE

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BYZGJAC2.0*;BYZGJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

IF STYLE/REPLY CODE(s) ADF OR ADG WERE ENTERED FOR MRC ARJD, YOU MUST ANSWER MRC (BXSH)

ARJDDDESIGN FORM

THE PHYSICAL CONFIGURATION OF THE ITEM.

Enter the applicable reply code from the table below

(ARJDDADF*;ARJDDAAM$DADG*)

Table 1
	Reply Code (AL52)	Reply
	AAM	PLAIN
	ADF	SPOKED
	ADG	WEBBED

BXSH*DWEB/SPOKE RELATIONSHIP TO FACE CENTERLINE

AN INDICATION OF THE RELATIONSHIP BETWEEN THE WEBBING OR SPOKES AND THE CENTERLINE OF THE FACE.

Enter the applicable reply code from the table below

(BXSHDA)

Table 1
	Reply Code (AE98)	Reply
	A	ANY ACCEPTABLE
	SW	NOT OFFSET
	TK	OFFSET

BXSJDLIGHTENING HOLE

AN INDICATION OF WHETHER A LIGHTENING HOLE/S/ IS/ARE INCLUDED. PLEASE USE MRC ABFF FOR NIINS THAT WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable reply code from the table below

(BXSJDB)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

BXSKDINTEGRAL COOLING VANE

AN INDICATION OF WHETHER OR NOT AN INTEGRAL COOLING VANE(S) IS INCLUDED.

Enter the applicable reply code from the table below

(BXSKDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

IF STYLE/REPLY CODE(s) PD WERE ENTERED FOR MRC BXSM, YOU MUST ANSWER MRC (AXHQ and ABGA and ABGF and AGWA)

IF STYLE/REPLY CODE(s) ZK WERE ENTERED FOR MRC BXSM, YOU MUST ANSWER MRC (AXHQ and ABGA and ABGF and AGGS)

BXSMDGROOVE SHAPE

THE PHYSICAL CONFIGURATION OF THE GROOVE.

Enter the applicable reply code from the table below

(BXSMDPD*;BXSMDZK$DPD*)

Table 1
	Reply Code (AD07)	Reply
	PD	U
	ZK	V

AXHQ*AGROOVE QUANTITY

THE NUMBER OF GROOVES PROVIDED.

Enter the numeric reply with a minimum of one digit.

(AXHQA10*)

ABGA*JGROOVE DEPTH

A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABGAJAC2.0*;ABGAJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABGF*JGROOVE WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABGFJAC2.0*;ABGFJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AGWA*JGROOVE RADIUS

A MEASUREMENT OF A LINE SEGMENT EXTENDING FROM THE CENTER OF A GROOVE TO THE INSIDE SURFACE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AGWAJAA2.0*;AGWAJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AGGS*BV GROOVE ANGLE IN DEG

THE ANGLE OF THE V GROOVE,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AGGSB2.0)

BXSN*ASTANDARD V-BELT SECTION DESIGNATION FOR WHICH DESIGNED

THE ALPHA AND/OR NUMERIC SECTION DESIGNATION OF THE STANDARD V-BELT FOR WHICH DESIGNED.

Enter the alpha-numeric reply with a minimum of one character.

(BXSNAJ3)

IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BYDS, YOU MUST ANSWER MRC (AWJQ and ASBP and AXND)

BYDSDBORE FEATURE

AN INDICATION OF WHETHER OR NOT A BORE FEATURE IS INCLUDED.

Enter the applicable reply code from the table below

(BYDSDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AWJQ, YOU MUST ANSWER MRC (BYDT and BDDY)

AWJQ*DBEARINGS

AN INDICATION OF WHETHER BEARINGS ARE INCLUDED. PLEASE USE MRC ABFF FOR NIINS THAT WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable reply code from the table below

(AWJQDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

IF STYLE/REPLY CODE(s) AF WERE ENTERED FOR MRC BYDT, YOU MUST ANSWER MRC (BYDW)

BYDT*DBEARING TYPE

INDICATES THE TYPE OF BEARING PROVIDED.

Enter the applicable reply code from the table below

(BYDTDA*;BYDTDAH$DAG*;BYDTDAH$$DAG*)

Table 1
	Reply Code (AH96)	Reply
	AD	ANNULAR ROLLER
	A	ANY ACCEPTABLE
	AE	BALL
	AF	BEARING ROLLER
	AG	FLANGED
	AH	NEEDLE ROLLER
	AJ	ROLLER
	AK	SLEEVE

BYDW*JSHAFT SIZE FOR WHICH DESIGNED

DESIGNATES THE SIZE OF THE SHAFT FOR WHICH THE ITEM IS DESIGNED.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BYDWJAA2.0*;BYDWJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BDDY*ABEARING QUANTITY

THE NUMBER OF BEARINGS PROVIDED ON THE ITEM.

Enter the numeric reply with a minimum of one digit.

(BDDYA10*)

IF STYLE/REPLY CODE(s) AK WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ABSA and AXFG and BDTX and AAUJ and ABSC and AXFH)

IF STYLE/REPLY CODE(s) AB WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ABXV and ADGE and BSGG)

IF STYLE/REPLY CODE(s) AM WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ABSA and AAUJ and ABSC and AXFH)

IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ADGE and ANAL and ANAM and BSGG)

ASBP*DBORE TYPE

INDICATES THE TYPE OF BORE USED ON THE ITEM.

Enter the applicable reply code from the table below

(ASBPDAM*;ASBPDAB$DAC*)

Table 1
	Reply Code (AL72)	Reply
	AK	INVOLUTE SPLINE
	AB	STRAIGHT
	AM	STRAIGHT SPLINE
	AC	TAPERED

ABSA*ASPLINE QUANTITY

THE NUMBER OF SPLINES ON OR IN THE ITEM.

Enter the numeric reply with a minimum of one digit.

(ABSAA10*)

AXFG*BSPLINE PRESSURE ANGLE IN DEG

THE PRESSURE ANGLE OF THE SPLINE,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AXFGB2.0)

BDTX*JSPLINE PITCH DIAMETER

A MEASUREMENT OF THE SPLINE PITCH DIAMETER.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BDTXJAA2.0*;BDTXJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AAUJ*JSPLINE MAJOR DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAUJJAC2.0*;AAUJJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABSC*JSPLINE MINOR DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. PLEASE USE MRC AAUH IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABSCJAC2.0*;ABSCJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AXFH*JSPLINE LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF A SPLINE,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AXFHJAB2.0*;AXFHJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABXV*JBORE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABXVJAB2.0*;ABXVJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADGE*JBORE LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF A BORE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADGEJAB2.0*;ADGEJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BYDX*DTAPERED SPLINE LARGEST MINOR DIAMETER LOCATION

INDICATES THE LOCATION OF THE TAPERED SPLINE LARGEST MINOR DIAMETER.

Enter the applicable reply code from the table below

(BYDXDBCA*;BYDXDBBZ$DBBZ*)

Table 1
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END

ANAL*JTAPER BORE MAJOR DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ANALJAC2.0*;ANALJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ANAM*JTAPER BORE MINOR DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ANAMJAC2.0*;ANAMJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AWPJ*DTAPER MAJOR DIAMETER LOCATION

INDICATES THE LOCATION OF THE TAPER MAJOR DIAMETER.

Enter the applicable reply code from the table below

(AWPJDBBZ*;AWPJDBCA$DBBZ*)

Table 1
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END

IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AXND, YOU MUST ANSWER MRC (BDYS and AAWY and AAWZ)

AXND*DCOUNTERBORE FEATURE

AN INDICATION OF WHETHER OR NOT A COUNTERBORE FEATURE IS INCLUDED.

Enter the applicable reply code from the table below

(AXNDDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

BDYS*DCOUNTERBORE LOCATION

INDICATES THE LOCATION OF THE COUNTERBORE ON THE ITEM.

Enter the applicable reply code from the table below

(BDYSDBCA*;BDYSDBBZ$DAHH*)

Table 1
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS

AAWY*JCOUNTERBORE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAWYJAB2.0*;AAWYJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AAWZ*JCOUNTERBORE DEPTH

THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AAWZJAC2.0*;AAWZJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BSGG, YOU MUST ANSWER MRC (BSGK)

BSGG*DKEYING FACILITY

AN INDICATION OF WHETHER OR NOT A KEYING FACILITY IS INCLUDED. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable reply code from the table below

(BSGGDC)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

IF STYLE/REPLY CODE(s) BZT WERE ENTERED FOR MRC BSGK, YOU MUST ANSWER MRC (NMBR and ABRR and AEVF)

BSGK*DKEYING FACILITY TYPE

INDICATES THE TYPE OF KEYING FACILITY PROVIDED.

Enter the applicable reply code from the table below

(BSGKDCDS*;BSGKDBZT$DBZS*)

Table 1
	Reply Code (AK54)	Reply
	BZS	INTEGRAL KEY
	BZT	KEYWAY
	CDS	TAPERED KEYWAY

NMBR*AQUANTITY

A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.

Enter the numeric reply with a minimum of one digit.

(NMBRA10*)

ABSF*JKEY WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEY,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABSFJAC2.0*;ABSFJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEVD*JDISTANCE FROM CENTER OF BORE TO TOP OF KEY

THE DISTANCE FROM THE CENTER OF THE BORE TO THE TOP OF THE KEY/S/.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEVDJAB2.0*;AEVDJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEVG*BKEY SPACING IN DEG

A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AEVGB2.0)

BYDY*DKEYING FACILITY LARGEST DIMENSION LOCATION

INDICATES THE LOCATION OF THE LARGEST DIMENSION OF THE KEYING FACILITY.

Enter the applicable reply code from the table below

(BYDYDBBZ*;BYDYDBCA$DBBZ*)

Table 1
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END

ABRR*JKEYWAY WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABRRJAA2.0*;ABRRJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEVF*JDISTANCE FROM CENTER OF BORE TO BOTTOM OF KEYWAY

THE DISTANCE FROM THE CENTER OF THE BORE TO THE BOTTOM OF THE KEYWAY(S).

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEVFJAB2.0*;AEVFJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEVJ*BKEYWAY SPACING IN DEG

A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEYWAY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AEVJB2.0)

BYDZ*DPROTRUDING HUB CHARACTERISTIC

AN INDICATION OF THE CHARACTERISTIC OF THE PROTRUDING HUB.

Enter the applicable reply code from the table below

(BYDZDAAG*;BYDZDAAH$DAAJ*)

Table 1
	Reply Code (AJ88)	Reply
	AAG	GROOVED
	AAJ	PLAIN
	AAH	STEPPED

BYZQ*JTHIRD STEP FACE LARGEST DIAMETER AND LOCATION

THE LARGEST DIAMETER AND LOCATION OF THE THIRD STEP FACE.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BYZQJACAHH2.0*;BYZQJACAHH2.0$$JACAHH2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS

Reference Notes

Refer to Reference Drawings for assitance in answering this MRC.

BYZX*JTHIRD STEP LENGTH AND LOCATION

THE LENGTH AND LOCATION OF THE THIRD STEP.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BYZXJAABBZ2.0*;BYZXJAABBZ2.0$$JAABBZ2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS

Reference Notes

Refer to Reference Drawings for assitance in answering this MRC.

BYZY*JFOURTH STEP LENGTH AND LOCATION

THE LENGTH AND LOCATION OF THE FOURTH STEP.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BYZYJAABBZ2.0*;BYZYJAABBZ2.0$$JAABBZ2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS

Reference Notes

Refer to Reference Drawings for assitance in answering this MRC.

BZBC*JSECOND END GROOVE DIAMETER AND LOCATION

THE DIAMETER AND LOCATION OF THE SECOND END GROOVE.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(BZBCJABAHH2.0*;BZBCJABAHH2.0$$JABAHH2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS

Reference Notes

Refer to Reference Drawings for assitance in answering this MRC.

CLYS*JDISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION

THE DISTANCE FROM THE OUTSIDE FLANGE OR RIM TO THE HUB END, AND ITS LOCATION.

Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CLYSJAABBZ2.0*;CLYSJAABBZ2.0$$JAABBZ2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

Table 3
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS

Reference Notes

Refer to Reference Drawings for assitance in answering this MRC.

IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BSYG, YOU MUST ANSWER MRC (BYFC and BYFD)

BSYGDSPLIT HUB FEATURE

AN INDICATION OF WHETHER OR NOT A SPLIT HUB FEATURE IS INCLUDED.

Enter the applicable reply code from the table below

(BSYGDB)

Table 1
	Reply Code (AA49)	Reply
	B	INCLUDED
	C	NOT INCLUDED

BYFC*DHUB SPLIT LOCATION

INDICATES THE LOCATION OF THE SPLIT(S) ON THE HUB.

Enter the applicable reply code from the table below

(BYFCDCBQ*;BYFCDCBP$DCBP*)

Table 1
	Reply Code (AJ91)	Reply
	CBP	THROUGH BOTH WALLS
	CBQ	THROUGH ONE WALL

BYFD*ACLAMPING BOLT QUANTITY

THE NUMBER OF CLAMPING BOLTS PROVIDED.

Enter the numeric reply with a minimum of one digit.

(BYFDA10*)

IF YOU ANSWER MRC BSNP, YOU MUST ANSWER MRC (BYFF)

IF STYLE/REPLY CODE(s) AHF WERE ENTERED FOR MRC BSNP, YOU MUST ANSWER MRC (AHYF and BFYT and ABUJ) or (AHYF and BFYT and THSD)

IF STYLE/REPLY CODE(s) BFY WERE ENTERED FOR MRC BSNP, YOU MUST ANSWER MRC (AHYF and BFYT and AGGP) or (AHYF and BFYT and BYFG)

BSNP*DSECURING METHOD

THE MEANS BY WHICH THE ITEM IS SECURED.

Enter the applicable reply code from the table below

(BSNPDBFG*;BSNPDBGB$DBGG*;BSNPDBGB$$DBGG*)

Table 1
	Reply Code (AM39)	Reply
	A	ANY ACCEPTABLE
	BFT	AXIALLY LOCATED SCREW
	BFW	BOLTED THROUGH BORE
	ABD	BUSHING
	ABH	CLAMP
	AEM	COMPRESSION
	BFX	COTTER PIN
	BFY	DRILLED HOLE
	BFG	KEY
	BFZ	MOUNTED BETWEEN BRACKETS
	BGA	NUT
	AAD	PIN
	ADC	PRESS FIT
	BGB	PRESS FIT BEARING
	AHK	RETAINING PLATE
	BGC	RETAINING RING
	AAG	RIVET
	AAF	SETSCREW
	BGD	SLOTTED
	AHL	SNAP RING
	BGE	SOLDERED
	ABZ	SPACER
	BGF	SPLIT-TAPERED BUSHING
	BGG	STAKED
	AAE	STUD
	BGH	TAPERED-LOCK BUSHING
	AHF	THREADED HOLE
	AKK	WELDED

BYFF*DSECURING LOCATION

INDICATES THE LOCATION FOR SECURING THE ITEM.

Enter the applicable reply code from the table below

(BYFFDADM*;BYFFDBCA$DBBZ*;BYFFDBCA$$DBBZ*)

Table 1
	Reply Code (AJ91)	Reply
	BBZ	AA END
	BCA	BB END
	AHH	BOTH ENDS
	ADM	PULLEY SURFACE

AHYF*ASECURING HOLE QUANTITY

THE NUMBER OF HOLES PROVIDED FOR SECURING THE ITEM IN A FIXED POSITION.

Enter the numeric reply with a minimum of one digit.

(AHYFA10*)

ABUJ*ATHREAD SIZE

DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.

Enter the alpha-numeric reply with a minimum of one character.

(ABUJAJ5)

IF YOU ANSWER MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJF and CQQR) or (CQJX and AAJF and AAJE)

THSD*DTHREAD SERIES DESIGNATOR

A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.

Enter the applicable reply code from the table below

(THSDDSS)

Table 1
	Reply Code (AH06)	Reply
	SM	ISO M
	SS	ISO S
	EM	M
	MJ	MJ
	SJ	SI
	SK	SI-M

CQJX*JNOMINAL THREAD SIZE

A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CQJXJA2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

CTTC*JTHREAD TOLERANCE CLASS

A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.

Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.

(CTTCJNTETEXT1234*)

Table 1
	Reply Code (AN73)	Reply
	EXT	EXTERNAL
	NTE	INTERNAL

CQQR*BTHREAD PITCH IN MILLIMETERS

A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(CQQRB2.0)

AAJE*JTHREAD PITCH DIAMETERS

THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.

(AAJEJAM32.0/P50.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

AAJF*DTHREAD DIRECTION

THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.

Enter the applicable reply code from the table below

(AAJFDAAG)

Table 1
	Reply Code (AA38)	Reply
	AAG	LEFT-HAND
	AAL	RIGHT-HAND

BFYT*GHOLE LOCATION

INDICATES THE LOCATION OF THE HOLE ON THE ITEM.

Enter clear text.

(BFYTGCLEARTEXT)

ABKG*JBOLT CIRCLE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABKGJAA2.0*;ABKGJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AGGP*JDRILLED HOLE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRILLED HOLE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AGGPJAB2.0*;AGGPJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

BYFG*ATAPERED HOLE SIZE

DESIGNATES THE STANDARD SIZE DESIGNATION OF THE TAPERED HOLE.

Enter the alpha-numeric reply with a minimum of one character.

(BYFGAI0)

AKYN*GFURNISHED ITEMS AND QUANTITY

THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.

Enter clear text.

(AKYNGCLEARTEXT)

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

SPCL*GSPECIAL TEST FEATURES

TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.

Enter the reply in clear text.

(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZW*GDEPARTURE FROM CITED DOCUMENT

THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.

Enter the reply in clear text.

(ZZZWGAS MODIFIED BY MATERIAL*)

ZZZX*GDEPARTURE FROM CITED DESIGNATOR

THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.

Enter the reply in clear text.

(ZZZXGAS MODIFIED BY MATERIAL*)

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION

A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.

Enter the Reply Code from the table below.

(ELCDDA*)

Table 1
	Reply Code (AN58)	Reply
	A	ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD

AWJN*JUNPACKAGED UNIT WEIGHT

THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AWJNJAS2.0*)

Table 1
	Reply Code (AG67)	Reply
	AJ	KILOGRAMS
	AS	POUNDS

PRMT*DPRECIOUS MATERIAL

IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.

Enter the applicable reply code from the table below

(PRMTDRHA000*;PRMTDAUA000$DAGA000*;PRMTDAUA000$$DAGA000*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

PMWT*JPRECIOUS MATERIAL AND WEIGHT

AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(PMWTJRTA000E2.0*;PMWTJRTA000E2.0$$JRTA000E2.1*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

Table 2
	Reply Code (AG14)	Reply
	E	GRAINS, TROY
	R	GRAMS
	F	OUNCES, TROY

PMLC*JPRECIOUS MATERIAL AND LOCATION

AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.

Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.

(PMLCJAUA0002.0*;PMLCJAUA0002.0$JAUA0002.0*;PMLCJAUA0002.0$$JAUA0002.1*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

SUPP*GSUPPLEMENTARY FEATURES

CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.

Enter the reply in clear text.Separate multiple replies with a semicolon.

(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)

ZZZV*GFSC APPLICATION DATA

THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.

Enter the name of the next higher classifiable assembly in clear text.

(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

MATTDMATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.

Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2

(MATT3AEEDALA000*;MATT3AEEDALA000$DMGB000*;MATT3AEEDALA000$$DMGB000*)

Table 1
	ISAC Field Indicator (5000)	Location
	3AAT	BODY
	3AEE	OVERALL
	3HOU	LOCATION NOT OTHERWISE SPECIFIED

Table 2
	Reply Code (MA01)	Reply
	ALA000	ALUMINUM
	ALB000	ALUMINUM ALLOY
	AL7075	ALUMINUM ALLOY 7075
	CUA000	COPPER
	CUB000	COPPER ALLOY
	FEA000	IRON
	MGB000	MAGNESIUM ALLOY
	PCA000	PLASTIC
	PCP000	PLASTIC POLYAMIDE (NYLON)
	PCAF00	PLASTIC POLYTETRAFLUOROETHYLENE
	STA000	STEEL
	STB000	STEEL CORROSION RESISTING

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)