An item fabricated from electrically nonconductive material specifically designed to provide a support for mounting an electrical and/or an electronic component such as a semiconductor device, relay, or resistor into the next higher assembly. It isolates the component from the mounting surface of the next higher assembly, it may act as a strain relief to avoid damage to the component seal, and it may permit soldering of the component to the next higher assembly without damage. It includes holes, notches, or other provisions for physical alignment and spacing of electrical leads and/or other mounting facilities projecting from the component it mounts. It may also afford protection from shock or vibration. It may be either nonthermally conductive which protects the component from temperature changes in the next higher assembly or it may be thermally conductive which permits heat generated in the component to be drained out to a heat sink. For items whose function is electrical insulation only, see INSULATOR, (as modified). Excludes:HOLDER, (as modified); RETAINER, (as modified), and SPACER, PLATE.
ISAC Reply 3AEE added to MRC MATT.
ISAC Reply 3HOU added to MRC MATT.
ISAC Reply 3AEE added to MRC MDCL.
ISAC Reply 3HOU added to MRC MDCL.
ISAC Reply 3AEE added to MRC AXHR.
ISAC Reply 3ASZ added to MRC AXHR.
ISAC Reply 3ATA added to MRC AXHR.
ISAC Reply 3ATB added to MRC AXHR.
ISAC Reply 3ATC added to MRC AXHR.
ISAC Reply 3ATD added to MRC AXHR.
ISAC Reply 3BHK added to MRC AXHR.
ISAC Reply 3HOU added to MRC AXHR.
ISAC Reply 1A deleted from MRC AXHR.
ISAC Reply 1B deleted from MRC AXHR.
ISAC Reply 1C deleted from MRC AXHR.
ISAC Reply 1D deleted from MRC AXHR.
ISAC Reply 1X deleted from MRC AXHR.
ISAC Reply 1Z deleted from MRC AXHR.
ISAC Reply 3AEE added to MRC AEBV.
ISAC Reply 3ASZ added to MRC AEBV.
ISAC Reply 3ATA added to MRC AEBV.
ISAC Reply 3ATB added to MRC AEBV.
ISAC Reply 3ATC added to MRC AEBV.
ISAC Reply 3ATD added to MRC AEBV.
ISAC Reply 3BHK added to MRC AEBV.
ISAC Reply 3HOU added to MRC AEBV.
ISAC Reply 1A deleted from MRC AEBV.
ISAC Reply 1B deleted from MRC AEBV.
ISAC Reply 1C deleted from MRC AEBV.
ISAC Reply 1D deleted from MRC AEBV.
ISAC Reply 1X deleted from MRC AEBV.
ISAC Reply 1Z deleted from MRC AEBV.
ISAC Reply 3AEE added to MRC ABVG.
ISAC Reply 3ASZ added to MRC ABVG.
ISAC Reply 3ATA added to MRC ABVG.
ISAC Reply 3ATD added to MRC ABVG.
ISAC Reply 3BHK added to MRC ABVG.
ISAC Reply 3HOU added to MRC ABVG.
ISAC Reply 1A deleted from MRC ABVG.
ISAC Reply 1B deleted from MRC ABVG.
ISAC Reply 1C deleted from MRC ABVG.
ISAC Reply 1D deleted from MRC ABVG.
ISAC Reply 1X deleted from MRC ABVG.
ISAC Reply 1Z deleted from MRC ABVG.
ISAC Reply 3AEE added to MRC THSD.
ISAC Reply 3ASZ added to MRC THSD.
ISAC Reply 3ATD added to MRC THSD.
ISAC Reply 3BHK added to MRC THSD.
ISAC Reply 3HOU added to MRC THSD.
ISAC Reply 1A deleted from MRC THSD.
ISAC Reply 1B deleted from MRC THSD.
ISAC Reply 1C deleted from MRC THSD.
ISAC Reply 1D deleted from MRC THSD.
ISAC Reply 1X deleted from MRC THSD.
ISAC Reply 1Z deleted from MRC THSD.
ISAC Reply 3AEE added to MRC CQJX.
ISAC Reply 3ASZ added to MRC CQJX.
ISAC Reply 3ATD added to MRC CQJX.
ISAC Reply 3BHK added to MRC CQJX.
ISAC Reply 3HOU added to MRC CQJX.
ISAC Reply 1A deleted from MRC CQJX.
ISAC Reply 1B deleted from MRC CQJX.
ISAC Reply 1C deleted from MRC CQJX.
ISAC Reply 1D deleted from MRC CQJX.
ISAC Reply 1X deleted from MRC CQJX.
ISAC Reply 1Z deleted from MRC CQJX.
ISAC Reply 3AEE added to MRC AAJD.
ISAC Reply 3ASZ added to MRC AAJD.
ISAC Reply 3ATD added to MRC AAJD.
ISAC Reply 3BHK added to MRC AAJD.
ISAC Reply 3HOU added to MRC AAJD.
ISAC Reply 1A deleted from MRC AAJD.
ISAC Reply 1B deleted from MRC AAJD.
ISAC Reply 1C deleted from MRC AAJD.
ISAC Reply 1D deleted from MRC AAJD.
ISAC Reply 1X deleted from MRC AAJD.
ISAC Reply 1Z deleted from MRC AAJD.
ISAC Reply 3AEE added to MRC CTTC.
ISAC Reply 3ATD added to MRC CTTC.
ISAC Reply 3HOU added to MRC CTTC.
ISAC Reply 1A deleted from MRC CTTC.
ISAC Reply 1B deleted from MRC CTTC.
ISAC Reply 1C deleted from MRC CTTC.
ISAC Reply 1D deleted from MRC CTTC.
ISAC Reply 1X deleted from MRC CTTC.
ISAC Reply 1Z deleted from MRC CTTC.
ISAC Reply 3AEE added to MRC CMLP.
ISAC Reply 3ASZ added to MRC CMLP.
ISAC Reply 3ATD added to MRC CMLP.
ISAC Reply 3BHK added to MRC CMLP.
ISAC Reply 3HOU added to MRC CMLP.
ISAC Reply 1A deleted from MRC CMLP.
ISAC Reply 1B deleted from MRC CMLP.
ISAC Reply 1C deleted from MRC CMLP.
ISAC Reply 1D deleted from MRC CMLP.
ISAC Reply 1X deleted from MRC CMLP.
ISAC Reply 1Z deleted from MRC CMLP.
ISAC Reply 3AEE added to MRC CQQR.
ISAC Reply 3ASZ added to MRC CQQR.
ISAC Reply 3HOU added to MRC CQQR.
ISAC Reply 1A deleted from MRC CQQR.
ISAC Reply 1B deleted from MRC CQQR.
ISAC Reply 1C deleted from MRC CQQR.
ISAC Reply 1D deleted from MRC CQQR.
ISAC Reply 1X deleted from MRC CQQR.
ISAC Reply 1Z deleted from MRC CQQR.
MRC AAJE has been deleted
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED61934*)
IF STYLE/REPLY CODE(s) 1B, 20B, 21B, 22B, 23B, 24B, 25B OR 26B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKW and ADAV)
IF STYLE/REPLY CODE(s) 2B, 3B, 4B, 5B, 6B, 7B, 8B, 9B, 10B, 11B, 12B, 13B, 14B, 15B, 16B, 17B, 18B, 19B, 27B, 28B, 29B OR 30B WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABKW and ABMK)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL26B)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BX10140 | 10B | RECTANGULAR |
| BX10141 | 11B | SQUARE |
| BX10142 | 12B | SQUARE |
| BX10143 | 13B | RECTANGULAR |
| BX10144 | 14B | SQUARE |
| BX10145 | 15B | RECTANGULAR |
| BX10146 | 16B | RECTANGULAR |
| BX10147 | 17B | RECTANGULAR |
| BX10148 | 18B | RECTANGULAR |
| BX10149 | 19B | STRIP |
| BX10263 | 1B | CYLINDRICAL |
| BX10150 | 20B | DISK |
| BX10151 | 21B | DISK |
| BX10152 | 22B | DISK |
| BX10153 | 23B | DISK |
| BX10154 | 24B | DISK |
| BX10155 | 25B | DISK |
| BX10156 | 26B | DISK |
| BX10157 | 27B | SQUARE |
| BX10158 | 28B | IRREGULAR |
| BX10159 | 29B | SQUARE |
| BX10264 | 2B | 90 DEGREE MOUNT |
| BX10160 | 30B | RECTANGULAR |
| BX10265 | 3B | STRIP-MOUNT |
| BX10266 | 4B | RECTANGULAR |
| BX10267 | 5B | RECTANGULAR |
| BX10268 | 6B | OVAL |
| BX10269 | 7B | VERTI-MOUNT |
| BX10270 | 8B | AXIAL-MOUNT |
| BX10139 | 9B | ANGLE-MOUNT |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HUESDCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDBL0000)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| BU0000 | BLUE |
| BR0000 | BROWN |
| CL0000 | CLEAR |
| GL0000 | GOLD |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| VY0000 | IVORY |
| NA0000 | NATURAL |
| RG0000 | ORANGE |
| RE0000 | RED |
| WH0000 | WHITE |
| YE0000 | YELLOW |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDST1117*;MATT3AEEDST1117$DPCR000*;MATT3AEEDST1117$$DPCR000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL2011 | ALUMINUM ALLOY 2011 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2018 | ALUMINUM ALLOY 2018 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL2025 | ALUMINUM ALLOY 2025 |
| AL2218 | ALUMINUM ALLOY 2218 |
| AL2219 | ALUMINUM ALLOY 2219 |
| AL2618 | ALUMINUM ALLOY 2618 |
| AL3003 | ALUMINUM ALLOY 3003 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL0051 | ALUMINUM ALLOY 357.0 |
| AL0029 | ALUMINUM ALLOY 360.0 |
| AL0031 | ALUMINUM ALLOY 380.0 |
| AL0054 | ALUMINUM ALLOY 383.0 |
| AL0032 | ALUMINUM ALLOY 384.0 |
| AL4032 | ALUMINUM ALLOY 4032 |
| AL0027 | ALUMINUM ALLOY 413.0 |
| AL0044 | ALUMINUM ALLOY 443.0 |
| AL5005 | ALUMINUM ALLOY 5005 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL0050 | ALUMINUM ALLOY 518.0 |
| AL5454 | ALUMINUM ALLOY 5454 |
| AL5456 | ALUMINUM ALLOY 5456 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6062 | ALUMINUM ALLOY 6062 |
| AL6063 | ALUMINUM ALLOY 6063 |
| AL6066 | ALUMINUM ALLOY 6066 |
| AL6101 | ALUMINUM ALLOY 6101 |
| AL6151 | ALUMINUM ALLOY 6151 |
| AL6262 | ALUMINUM ALLOY 6262 |
| AL7049 | ALUMINUM ALLOY 7049 |
| AL7075 | ALUMINUM ALLOY 7075 |
| AL7076 | ALUMINUM ALLOY 7076 |
| AL7178 | ALUMINUM ALLOY 7178 |
| AL0028 | ALUMINUM ALLOY A380.0 |
| AL0030 | ALUMINUM ALLOY A413.0 |
| ASA000 | ASBESTOS |
| BEA000 | BERYLLIUM |
| BEC000 | BERYLLIUM OXIDE |
| CDA000 | CADMIUM |
| CNA000 | CARBON |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0059 | COPPER ALLOY 101 |
| CU0249 | COPPER ALLOY 102 |
| CU0282 | COPPER ALLOY 103 |
| CU0286 | COPPER ALLOY 104 |
| CU0287 | COPPER ALLOY 105 |
| CU0288 | COPPER ALLOY 107 |
| CU0283 | COPPER ALLOY 108 |
| CU0063 | COPPER ALLOY 110 |
| CU0289 | COPPER ALLOY 113 |
| CU0290 | COPPER ALLOY 114 |
| CU0291 | COPPER ALLOY 116 |
| CU0247 | COPPER ALLOY 120 |
| CU0248 | COPPER ALLOY 122 |
| CU0292 | COPPER ALLOY 123 |
| CU0278 | COPPER ALLOY 125 |
| CU0324 | COPPER ALLOY 127 |
| CU0326 | COPPER ALLOY 128 |
| CU0315 | COPPER ALLOY 130 |
| CU0279 | COPPER ALLOY 142 |
| CU0281 | COPPER ALLOY 145 |
| CU0284 | COPPER ALLOY 147 |
| CU0285 | COPPER ALLOY 162 |
| CU0297 | COPPER ALLOY 165 |
| CU0068 | COPPER ALLOY 170 |
| CU0069 | COPPER ALLOY 172 |
| CU0233 | COPPER ALLOY 173 |
| CU0265 | COPPER ALLOY 175 |
| CU0338 | COPPER ALLOY 182 |
| CU0317 | COPPER ALLOY 184 |
| CU0318 | COPPER ALLOY 185 |
| CU0280 | COPPER ALLOY 187 |
| CU0263 | COPPER ALLOY 210 |
| CU0264 | COPPER ALLOY 220 |
| CU0074 | COPPER ALLOY 230 |
| CU0076 | COPPER ALLOY 240 |
| CU0079 | COPPER ALLOY 260 |
| CU0304 | COPPER ALLOY 262 |
| CU0080 | COPPER ALLOY 268 |
| CU0081 | COPPER ALLOY 270 |
| CU0272 | COPPER ALLOY 272 |
| CU0274 | COPPER ALLOY 274 |
| CU0302 | COPPER ALLOY 280 |
| CU0314 | COPPER ALLOY 314 |
| CU0316 | COPPER ALLOY 316 |
| CU0320 | COPPER ALLOY 320 |
| CU0330 | COPPER ALLOY 330 |
| CU0305 | COPPER ALLOY 331 |
| CU0332 | COPPER ALLOY 332 |
| CU0335 | COPPER ALLOY 335 |
| CU0340 | COPPER ALLOY 340 |
| CU0088 | COPPER ALLOY 342 |
| CU0306 | COPPER ALLOY 344 |
| CU0307 | COPPER ALLOY 345 |
| CU0308 | COPPER ALLOY 347 |
| CU0309 | COPPER ALLOY 348 |
| CU0310 | COPPER ALLOY 350 |
| CU0089 | COPPER ALLOY 353 |
| CU0090 | COPPER ALLOY 356 |
| CU0091 | COPPER ALLOY 360 |
| CU0370 | COPPER ALLOY 370 |
| CU0092 | COPPER ALLOY 377 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0465 | COPPER ALLOY 465 |
| CU0466 | COPPER ALLOY 466 |
| CU0467 | COPPER ALLOY 467 |
| CU0100 | COPPER ALLOY 482 |
| CU0101 | COPPER ALLOY 485 |
| CU0298 | COPPER ALLOY 502 |
| CU0299 | COPPER ALLOY 507 |
| CU0300 | COPPER ALLOY 508 |
| CU0103 | COPPER ALLOY 510 |
| CU0104 | COPPER ALLOY 511 |
| CU0105 | COPPER ALLOY 521 |
| CU0106 | COPPER ALLOY 524 |
| CU0108 | COPPER ALLOY 534 |
| CU0109 | COPPER ALLOY 544 |
| CU0111 | COPPER ALLOY 606 |
| CU0301 | COPPER ALLOY 607 |
| CU0115 | COPPER ALLOY 614 |
| CU0122 | COPPER ALLOY 630 |
| CU0303 | COPPER ALLOY 638 |
| CU0127 | COPPER ALLOY 642 |
| CU0129 | COPPER ALLOY 651 |
| CU0131 | COPPER ALLOY 655 |
| CU0706 | COPPER ALLOY 706 |
| CU0294 | COPPER ALLOY 710 |
| CU0715 | COPPER ALLOY 715 |
| CU0295 | COPPER ALLOY 732 |
| CU0146 | COPPER ALLOY 735 |
| CU0296 | COPPER ALLOY 740 |
| CU0148 | COPPER ALLOY 745 |
| CU0150 | COPPER ALLOY 752 |
| CU0757 | COPPER ALLOY 757 |
| CU0151 | COPPER ALLOY 762 |
| CU0152 | COPPER ALLOY 764 |
| CU0153 | COPPER ALLOY 766 |
| CU0157 | COPPER ALLOY 770 |
| CU0162 | COPPER ALLOY 794 |
| CU0172 | COPPER ALLOY 836 |
| CU0173 | COPPER ALLOY 838 |
| CU0174 | COPPER ALLOY 842 |
| CU0175 | COPPER ALLOY 844 |
| CU0178 | COPPER ALLOY 854 |
| CU0183 | COPPER ALLOY 863 |
| CU0185 | COPPER ALLOY 865 |
| CU0195 | COPPER ALLOY 903 |
| CU0196 | COPPER ALLOY 905 |
| CU0198 | COPPER ALLOY 910 |
| CU0202 | COPPER ALLOY 922 |
| CU0203 | COPPER ALLOY 923 |
| CU0206 | COPPER ALLOY 932 |
| CU0207 | COPPER ALLOY 934 |
| CU0208 | COPPER ALLOY 935 |
| CU0210 | COPPER ALLOY 938 |
| CU0212 | COPPER ALLOY 940 |
| CU0214 | COPPER ALLOY 943 |
| CUD000 | COPPER GRAPHITE |
| FBA000 | FIBER |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| MTC000 | METAL |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCD000 | PLASTIC ACRYLIC |
| PCAX00 | PLASTIC ACRYLONITRILE |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCE000 | PLASTIC ALKYD |
| PCF000 | PLASTIC ALLYL |
| PCAAM0 | PLASTIC AMINO |
| PCAN00 | PLASTIC CELLULOSE ACETATE |
| PCBN00 | PLASTIC CELLULOSE ACETATE BUTYRATE |
| PCBJ00 | PLASTIC CELLULOSE NITRATE |
| PCAAN0 | PLASTIC CELLULOSE PROPIONATE |
| PCAAB0 | PLASTIC CELLULOSE TRIACETATE |
| PCAAZ0 | PLASTIC CHLORINATED POLYESTER |
| PCAAQ0 | PLASTIC CHLOROTRIFLUOROETHYLENE |
| PCBP00 | PLASTIC DIALLYL ISOPHTHALATE |
| PCG000 | PLASTIC DIALLYL PHTHALATE |
| PCAAK0 | PLASTIC DIALLYL PHTHALATE MINERAL FILLED |
| PCH000 | PLASTIC EPOXY |
| PCBY00 | PLASTIC ETHYL CELLULOSE |
| PCBR00 | PLASTIC FLUORINATED ETHYLENE PROPYLENE |
| PCAAD0 | PLASTIC FLUOROCARBON |
| PCAAE0 | PLASTIC FLUOROSILICONE |
| PCAAR0 | PLASTIC FURANE |
| PCAAS0 | PLASTIC ISOCYANATE |
| PCJ000 | PLASTIC MELAMINE |
| PCAAJ0 | PLASTIC MELAMINE MINERAL FILLED |
| PCBB00 | PLASTIC METHACRYLATE |
| PCAAG0 | PLASTIC MINERAL FILLED |
| PCM000 | PLASTIC PHENOL FORMALDEHYDE (PMO) |
| PCN000 | PLASTIC PHENOLIC |
| PCAAH0 | PLASTIC PHENOLIC MINERAL FILLED |
| PCBK00 | PLASTIC PHENOXY |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCS000 | PLASTIC POLYCHLOROFLUOROETHYLENE |
| PCT000 | PLASTIC POLYCHLOROTRIFLUOROETHYLENE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE (PET) |
| PCAAY0 | PLASTIC POLYHYDROXY |
| PCBE00 | PLASTIC POLYPHENYLENE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAD00 | PLASTIC POLYSTYRENE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAG00 | PLASTIC POLYTRIFLUOROCHLOROETHYLENE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCBM00 | PLASTIC POLYVINYL ACETATE |
| PCAAT0 | PLASTIC POLYVINYL ALCOHOL |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE (PVC) |
| PCBT00 | PLASTIC POLYVINYL FLUORIDE |
| PCBG00 | PLASTIC POLYVINYLIDENE CHLORIDE |
| PCAY00 | PLASTIC PYROXYLIN |
| PCAK00 | PLASTIC SILICONE |
| PCAAL0 | PLASTIC SILICONE MINERAL FILLED |
| PCBC00 | PLASTIC STYRENE |
| PCAAW0 | PLASTIC STYRENE ACRYLONITRILE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PCAL00 | PLASTIC UREA |
| PCAAX0 | PLASTIC UREA-FORMALDEHYDE |
| PCAAA0 | PLASTIC VINYL ACETATE |
| RCE000 | RUBBER |
| RC0019 | RUBBER BUTADIENE-ACRYLONITRILE CLASS NBR |
| RC0022 | RUBBER BUTADIENE-STYRENE CLASS SBR |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RC0014 | RUBBER FLUOROSILICONE CLASS FQ |
| RCA000 | RUBBER NATURAL |
| RCJ000 | RUBBER POLYBUTADIENE |
| RCP000 | RUBBER POLYISOBUTYLENE |
| RC0021 | RUBBER SILICONE CLASS Q |
| RCB000 | RUBBER SYNTHETIC |
| STA000 | STEEL |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1010 | STEEL COMP 1010 |
| ST1011 | STEEL COMP 1011 |
| ST1012 | STEEL COMP 1012 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1021 | STEEL COMP 1021 |
| ST1022 | STEEL COMP 1022 |
| ST1023 | STEEL COMP 1023 |
| ST1024 | STEEL COMP 1024 |
| ST1025 | STEEL COMP 1025 |
| ST1026 | STEEL COMP 1026 |
| ST1027 | STEEL COMP 1027 |
| ST1029 | STEEL COMP 1029 |
| ST1030 | STEEL COMP 1030 |
| ST1031 | STEEL COMP 1031 |
| ST1033 | STEEL COMP 1033 |
| ST1035 | STEEL COMP 1035 |
| ST1036 | STEEL COMP 1036 |
| ST1037 | STEEL COMP 1037 |
| ST1038 | STEEL COMP 1038 |
| ST1039 | STEEL COMP 1039 |
| ST1040 | STEEL COMP 1040 |
| ST1041 | STEEL COMP 1041 |
| ST1042 | STEEL COMP 1042 |
| ST1045 | STEEL COMP 1045 |
| ST1046 | STEEL COMP 1046 |
| ST1049 | STEEL COMP 1049 |
| ST1050 | STEEL COMP 1050 |
| ST1051 | STEEL COMP 1051 |
| ST1052 | STEEL COMP 1052 |
| ST1053 | STEEL COMP 1053 |
| ST1055 | STEEL COMP 1055 |
| ST1059 | STEEL COMP 1059 |
| ST1060 | STEEL COMP 1060 |
| ST1061 | STEEL COMP 1061 |
| ST1064 | STEEL COMP 1064 |
| ST1065 | STEEL COMP 1065 |
| ST1069 | STEEL COMP 1069 |
| ST1070 | STEEL COMP 1070 |
| ST1072 | STEEL COMP 1072 |
| ST1074 | STEEL COMP 1074 |
| ST1075 | STEEL COMP 1075 |
| ST1078 | STEEL COMP 1078 |
| ST1080 | STEEL COMP 1080 |
| ST1084 | STEEL COMP 1084 |
| ST1085 | STEEL COMP 1085 |
| ST1086 | STEEL COMP 1086 |
| ST1090 | STEEL COMP 1090 |
| ST1095 | STEEL COMP 1095 |
| ST1108 | STEEL COMP 1108 |
| ST1109 | STEEL COMP 1109 |
| ST1110 | STEEL COMP 1110 |
| ST1115 | STEEL COMP 1115 |
| ST1116 | STEEL COMP 1116 |
| ST1117 | STEEL COMP 1117 |
| ST1118 | STEEL COMP 1118 |
| ST1119 | STEEL COMP 1119 |
| ST1120 | STEEL COMP 1120 |
| ST1126 | STEEL COMP 1126 |
| ST1132 | STEEL COMP 1132 |
| ST1137 | STEEL COMP 1137 |
| ST1138 | STEEL COMP 1138 |
| ST1139 | STEEL COMP 1139 |
| ST1140 | STEEL COMP 1140 |
| ST1141 | STEEL COMP 1141 |
| ST1144 | STEEL COMP 1144 |
| ST1145 | STEEL COMP 1145 |
| ST1146 | STEEL COMP 1146 |
| ST1151 | STEEL COMP 1151 |
| ST1211 | STEEL COMP 1211 |
| ST1212 | STEEL COMP 1212 |
| ST1213 | STEEL COMP 1213 |
| ST1215 | STEEL COMP 1215 |
| ST0063 | STEEL COMP 12L14 |
| ST1330 | STEEL COMP 1330 |
| ST1345 | STEEL COMP 1345 |
| ST0201 | STEEL COMP 201 |
| ST0202 | STEEL COMP 202 |
| ST0159 | STEEL COMP 203EZ |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0180 | STEEL COMP 302B |
| ST0303 | STEEL COMP 303 |
| ST0166 | STEEL COMP 303 PLUS X |
| ST0157 | STEEL COMP 303CU |
| ST0165 | STEEL COMP 303MA |
| ST0158 | STEEL COMP 303PB |
| ST0078 | STEEL COMP 303S |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0305 | STEEL COMP 305 |
| ST0152 | STEEL COMP 308 |
| ST0309 | STEEL COMP 309 |
| ST0153 | STEEL COMP 309S |
| ST0310 | STEEL COMP 310 |
| ST0154 | STEEL COMP 310S |
| ST0155 | STEEL COMP 314 |
| ST0316 | STEEL COMP 316 |
| ST0354 | STEEL COMP 316F |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0254 | STEEL COMP 317L |
| ST0321 | STEEL COMP 321 |
| ST0322 | STEEL COMP 322 |
| ST0323 | STEEL COMP 323 |
| ST0324 | STEEL COMP 324 |
| ST0347 | STEEL COMP 347 |
| ST0348 | STEEL COMP 348 |
| ST0384 | STEEL COMP 384 |
| ST0385 | STEEL COMP 385 |
| ST0403 | STEEL COMP 403 |
| ST0405 | STEEL COMP 405 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST0414 | STEEL COMP 414 |
| ST4140 | STEEL COMP 4140 |
| ST0416 | STEEL COMP 416 |
| ST0255 | STEEL COMP 416 PLUS X |
| ST0099 | STEEL COMP 416SE |
| ST0420 | STEEL COMP 420 |
| ST0100 | STEEL COMP 420F |
| ST0284 | STEEL COMP 420FSE |
| ST0430 | STEEL COMP 430 |
| ST0101 | STEEL COMP 430F |
| ST0172 | STEEL COMP 430FSE |
| ST0431 | STEEL COMP 431 |
| ST4340 | STEEL COMP 4340 |
| ST0105 | STEEL COMP 440A |
| ST0106 | STEEL COMP 440B |
| ST0107 | STEEL COMP 440C |
| ST0108 | STEEL COMP 440F |
| ST0285 | STEEL COMP 440FSE |
| ST0446 | STEEL COMP 446 |
| ST4620 | STEEL COMP 4620 |
| ST6150 | STEEL COMP 6150 |
| ST0129 | STEEL COMP 6150H |
| ST0630 | STEEL COMP 630 |
| ST8620 | STEEL COMP 8620 |
| ST0143 | STEEL COMP 8650H |
| ST0145 | STEEL COMP 8660H |
| ST0014 | STEEL COMP B1111 |
| ST0015 | STEEL COMP B1112 |
| ST0016 | STEEL COMP B1113 |
| ST0298 | STEEL COMP W110 |
| STB000 | STEEL CORROSION RESISTING |
| ST0628 | STEEL UNS S34720 |
| ST0629 | STEEL UNS S34723 |
| TLA000 | TELLURIUM |
| SNB000 | TIN |
| SNA000 | TIN ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDXXB000*;SFTTDALA000$DPBA000*;SFTTDALA000$$DPBA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ALA000 | ALUMINUM ALLOY |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CNA000 | CARBON |
| CLB000 | CERAMIC |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| DCA000 | DICHROMATE |
| DCB000 | DICHROMATE POTASSIUM |
| DCD000 | DICHROMATE SODIUM |
| DCC000 | DICHROMATE ZINC |
| ENA000 | ENAMEL |
| AUA000 | GOLD |
| LQA000 | LACQUER |
| PBA000 | LEAD |
| PBB000 | LEAD ALLOY |
| LCC000 | LUBRICANT DRY FILM |
| NLA000 | NICKEL |
| NLC000 | NICKEL ALLOY |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PDA000 | PALLADIUM |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PCA000 | PLASTIC |
| PCK000 | PLASTIC ACRYLIC |
| PCN000 | PLASTIC DIALLYL PHTHALATE |
| PCL000 | PLASTIC MELAMINE |
| PCM000 | PLASTIC PHENOLIC |
| PCJ000 | PLASTIC POLYSTYRENE |
| PCP000 | PLASTIC POLYSULFONE |
| PCB000 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCH000 | PLASTIC VINYL |
| RHA000 | RHODIUM |
| RCA000 | RUBBER |
| RCB000 | RUBBER SYNTHETIC |
| SLA000 | SILICON |
| AGA000 | SILVER |
| AGB000 | SILVER ALLOY |
| SRA000 | SOLDER |
| SNA000 | TIN |
| ZNA000 | ZINC |
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
CZGX*LACCOMMODATED DEVICE MOUNTING HOLE PATTERN STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE PATTERN OF THE FACILITY BY WHICH THE DEVICE CAN BE MOUNTED.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(CZGXL204B)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BX10053 | 1000B | TEN HOLE |
| BX10054 | 1001B | TEN HOLE |
| BX10055 | 1002B | TEN HOLE |
| BX10056 | 1003B | TEN HOLE |
| BX10057 | 1004B | TEN HOLE |
| BX10058 | 1005B | TEN HOLE |
| DR01198 | 1006B | TEN HOLE - 0.200 INCH |
| DR01199 | 1007B | TEN HOLE - 0.230 INCH |
| DR01204 | 1008B | TEN HOLE - 0.350 INCH |
| DR01205 | 1009B | TEN HOLE - 0.380 INCH |
| DR01207 | 1010B | TEN HOLE - 0.420 INCH |
| DR01200 | 1012B | TEN HOLE - 0.250 INCH |
| DR01201 | 1013B | TEN HOLE - 0.273 INCH |
| DR01202 | 1014B | TEN HOLE - 0.320 INCH |
| DR01203 | 1015B | TEN HOLE - 0.330 INCH |
| DR01206 | 1016B | TEN HOLE - 0.400 INCH |
| DR01208 | 1017B | TEN HOLE - 0.430 INCH |
| DR01209 | 1018B | TEN HOLE - 0.830 INCH |
| DR01211 | 1019B | TEN HOLE - 0.100 INCH |
| DR01212 | 1020B | TEN HOLE - 0.200 INCH |
| BX10051 | 1021B | TEN HOLE |
| DR01261 | 1022B | TEN HOLE - 0.200 INCH |
| DR01262 | 1023B | TEN HOLE - 0.300 INCH |
| DR01263 | 1024B | TEN HOLE - 0.450 INCH |
| DR01129 | 1100B | ELEVEN HOLE - 0.200 INCH |
| DR01130 | 1101B | ELEVEN HOLE - 0.230 INCH |
| DR01136 | 1102B | ELEVEN HOLE - 0.350 INCH |
| DR01137 | 1103B | ELEVEN HOLE - 0.380 INCH |
| DR01131 | 1104B | ELEVEN HOLE - 0.250 INCH |
| DR01132 | 1105B | ELEVEN HOLE - 0.273 INCH |
| DR01133 | 1106B | ELEVEN HOLE - 0.290 INCH |
| DR01134 | 1107B | ELEVEN HOLE - 0.320 INCH |
| DR01135 | 1108B | ELEVEN HOLE - 0.330 INCH |
| DR01138 | 1109B | ELEVEN HOLE - 0.400 INCH |
| DR01139 | 1110B | ELEVEN HOLE - 0.420 INCH |
| DR01140 | 1111B | ELEVEN HOLE - 0.430 INCH |
| DR01160 | 1112B | ELEVEN HOLE - 0.830 INCH |
| BX10045 | 1113B | ELEVEN HOLE |
| BX10046 | 1114B | ELEVEN HOLE |
| BX10047 | 1115B | ELEVEN HOLE |
| BX10048 | 1116B | ELEVEN HOLE |
| DR01120 | 1117B | ELEVEN HOLE - 0.100 INCH |
| DR01121 | 1118B | ELEVEN HOLE - 0.200 INCH |
| BX10040 | 1200B | TWELVE HOLE |
| BX10041 | 1201B | TWELVE HOLE |
| DR01010 | 1202B | TWELVE HOLE - 0.215 INCH |
| DR01011 | 1203B | TWELVE HOLE - 0.230 INCH |
| DR01016 | 1204B | TWELVE HOLE - 0.365 INCH |
| DR01017 | 1205B | TWELVE HOLE - 0.380 INCH |
| DR01125 | 1206B | TWELVE HOLE - 0.100 INCH |
| DR01126 | 1207B | TWELVE HOLE - 0.200 INCH |
| BX10043 | 1208B | TWELVE HOLE |
| DR01009 | 1209B | TWELVE HOLE - 0.200 INCH |
| DR01012 | 1210B | TWELVE HOLE - 0.250 INCH |
| DR01013 | 1211B | TWELVE HOLE - 0.275 INCH |
| DR01014 | 1212B | TWELVE HOLE - 0.300 INCH |
| DR01015 | 1213B | TWELVE HOLE - 0.350 INCH |
| DR01018 | 1214B | TWELVE HOLE - 0.400 INCH |
| DR01019 | 1215B | TWELVE HOLE - 0.420 INCH |
| DR01020 | 1216B | TWELVE HOLE - 0.510 INCH |
| BX10036 | 1217B | TWELVE HOLE |
| BX10037 | 1218B | TWELVE HOLE |
| BX10038 | 1219B | TWELVE HOLE |
| BX10031 | 1220B | TWELVE HOLE |
| BX10032 | 1221B | TWELVE HOLE |
| BX10033 | 1222B | TWELVE HOLE |
| BX10034 | 1223B | TWELVE HOLE |
| BX10026 | 1300B | THIRTEEN HOLE |
| BX10028 | 1301B | THIRTEEN HOLE |
| BX10029 | 1302B | THIRTEEN HOLE |
| DR00994 | 1303B | THIRTEEN HOLE - 0.215 INCH |
| DR00995 | 1304B | THIRTEEN HOLE - 0.230 INCH |
| DR01000 | 1305B | THIRTEEN HOLE - 0.365 INCH |
| DR01001 | 1306B | THIRTEEN HOLE - 0.380 INCH |
| DR00993 | 1307B | THIRTEEN HOLE - 0.200 INCH |
| DR00996 | 1308B | THIRTEEN HOLE - 0.250 INCH |
| DR00997 | 1309B | THIRTEEN HOLE - 0.275 INCH |
| DR00998 | 1310B | THIRTEEN HOLE - 0.300 INCH |
| DR00999 | 1311B | THIRTEEN HOLE - 0.350 INCH |
| DR01002 | 1312B | THIRTEEN HOLE - 0.400 INCH |
| DR01003 | 1313B | THIRTEEN HOLE - 0.420 INCH |
| DR01004 | 1314B | THIRTEEN HOLE - 0.510 INCH |
| BX10245 | 1400B | FOURTEEN HOLE |
| BX10013 | 1401B | FOURTEEN HOLE |
| BX10023 | 1402B | FOURTEEN HOLE |
| DR00915 | 1403B | FOURTEEN HOLE - 0.250 INCH |
| DR00920 | 1404B | FOURTEEN HOLE - 0.420 INCH |
| DR00978 | 1405B | FOURTEEN HOLE - 0.300 INCH |
| DR00977 | 1406B | FOURTEEN HOLE - 0.100 INCH |
| DR00979 | 1407B | FOURTEEN HOLE - 0.450 INCH |
| DR00980 | 1408B | FOURTEEN HOLE - 1.300 INCH |
| DR00916 | 1409B | FOURTEEN HOLE - 0.290 INCH |
| DR00917 | 1410B | FOURTEEN HOLE - 0.350 INCH |
| DR00918 | 1411B | FOURTEEN HOLE - 0.380 INCH |
| DR00919 | 1412B | FOURTEEN HOLE - 0.400 INCH |
| DR00921 | 1413B | FOURTEEN HOLE - 0.450 INCH |
| DR00922 | 1414B | FOURTEEN HOLE - 0.750 INCH |
| DR00897 | 1417B | FOURTEEN HOLE - 0.100 INCH |
| DR00898 | 1418B | FOURTEEN HOLE - 0.200 INCH |
| DR00905 | 1500B | FIFTEEN HOLE - 0.250 INCH |
| DR00910 | 1501B | FIFTEEN HOLE - 0.420 INCH |
| DR00906 | 1502B | FIFTEEN HOLE - 0.290 INCH |
| DR00907 | 1503B | FIFTEEN HOLE - 0.350 INCH |
| DR00908 | 1504B | FIFTEEN HOLE - 0.380 INCH |
| DR00909 | 1505B | FIFTEEN HOLE - 0.400 INCH |
| DR00911 | 1506B | FIFTEEN HOLE - 0.450 INCH |
| DR00913 | 1507B | FIFTEEN HOLE - 0.750 INCH |
| BX10021 | 1508B | FIFTEEN HOLE |
| BX10019 | 1509B | FIFTEEN HOLE |
| BX10022 | 1510B | FIFTEEN HOLE |
| DR01725 | 1600B | SIXTEEN HOLE - 0.200 INCH |
| DR01726 | 1601B | SIXTEEN HOLE - 0.300 INCH |
| DR01724 | 1602B | SIXTEEN HOLE - 0.100 INCH |
| DR01727 | 1603B | SIXTEEN HOLE - 0.450 INCH |
| DR01728 | 1604B | SIXTEEN HOLE - 0.600 INCH |
| BX10014 | 1605B | SIXTEEN HOLE |
| BX10015 | 1606B | SIXTEEN HOLE |
| BX10016 | 1607B | SIXTEEN HOLE |
| BX10017 | 1608B | SIXTEEN HOLE |
| BX10213 | 1609B | SIXTEEN HOLE |
| BX10214 | 1610B | SIXTEEN HOLE |
| BX10215 | 1611B | SIXTEEN HOLE |
| BX10217 | 1612B | SIXTEEN HOLE |
| DR00991 | 1613B | SIXTEEN HOLE - 0.100 INCH |
| DR00992 | 1614B | SIXTEEN HOLE - 0.200 INCH |
| BX10216 | 1700B | SEVENTEEN HOLE |
| BX10218 | 1800B | EIGHTEEN HOLE |
| DR01735 | 1801B | EIGHTEEN HOLE - 0.300 INCH |
| DR01736 | 1802B | EIGHTEEN HOLE - 0.450 INCH |
| DR01731 | 1803B | EIGHTEEN HOLE 0.100 INCH |
| DR01732 | 1804B | EIGHTEEN HOLE - 0.200 INCH |
| BX10221 | 1900B | NINETEEN HOLE |
| BX10222 | 2000B | TWENTY HOLE |
| DR01753 | 2001B | TWENTY HOLE - 0.100 INCH |
| DR01754 | 2002B | TWENTY HOLE - 0.200 INCH |
| BX10224 | 2003B | TWENTY HOLE |
| DR01659 | 200B | TWO HOLE - 0.050 INCH |
| DR01660 | 201B | TWO HOLE - 0.075 INCH |
| DR01661 | 202B | TWO HOLE - 0.100 INCH |
| DR01662 | 203B | TWO HOLE - 0.115 INCH |
| DR01663 | 204B | TWO HOLE - 0.143 INCH |
| DR01664 | 205B | TWO HOLE - 0.192 INCH |
| DR01665 | 206B | TWO HOLE - 0.200 INCH |
| DR01666 | 207B | TWO HOLE - 0.238 INCH |
| DR01667 | 208B | TWO HOLE - 0.275 INCH |
| DR01668 | 209B | TWO HOLE - 0.430 INCH |
| DR01669 | 210B | TWO HOLE - 0.486 INCH |
| DR01670 | 211B | TWO HOLE - 0.500 INCH |
| DR01671 | 212B | TWO HOLE - 0.750 INCH |
| DR01672 | 213B | TWO HOLE - 0.875 INCH |
| DR01673 | 214B | TWO HOLE - 2.125 INCH |
| BX10225 | 2200B | TWENTY TWO HOLE |
| BX10226 | 2201B | TWENTY TWO HOLE |
| BX10227 | 2202B | TWENTY TWO HOLE |
| BX10228 | 2203B | TWENTY TWO HOLE |
| BX10229 | 2204B | TWENTY TWO HOLE |
| BX10230 | 2300B | TWENTY THREE HOLE |
| DR01756 | 2400B | TWENTY FOUR HOLE - 0.600 INCH |
| DR01755 | 2401B | TWENTY FOUR HOLE - 0.500 INCH |
| DR01757 | 2402B | TWENTY FOUR HOLE - 0.625 INCH |
| DR01758 | 2403B | TWENTY FOUR HOLE - 0.750 INCH |
| DR01759 | 2404B | TWENTY FOUR HOLE - 1.300 INCH |
| BX10232 | 2405B | TWENTY FOUR HOLE |
| BX10233 | 2406B | TWENTY FOUR HOLE |
| BX10234 | 2407B | TWENTY FOUR HOLE |
| DR01763 | 2408B | TWENTY FOUR HOLE - 0.100 INCH |
| DR01764 | 2409B | TWENTY FOUR HOLE - 0.200 INCH |
| BX10236 | 2410B | TWENTY FOUR HOLE |
| BX10237 | 2411B | TWENTY FOUR HOLE |
| BX10238 | 2500B | TWENTY FIVE HOLE |
| BX10239 | 2501B | TWENTY FIVE HOLE |
| DR00242 | 2800B | TWENTY EIGHT HOLE - 0.600 INCH |
| DR00243 | 2801B | TWENTY EIGHT HOLE - 0.625 INCH |
| DR00244 | 2802B | TWENTY EIGHT HOLE - 0.750 INCH |
| BX10241 | 2803B | TWENTY EIGHT HOLE |
| DR00245 | 2804B | TWENTY EIGHT HOLE - 0.100 INCH |
| DR00252 | 2805B | TWENTY EIGHT HOLE - 0.200 INCH |
| BX10243 | 2806B | TWENTY EIGHT HOLE |
| BX10244 | 2807B | TWENTY EIGHT HOLE |
| BX10011 | 2900B | TWENTY NINE HOLE |
| BX10012 | 3000B | THIRTY HOLE |
| BX10107 | 300B | THREE HOLE |
| BX10108 | 301B | THREE HOLE |
| DR01692 | 302B | THREE HOLE - 0.100 INCH |
| DR01694 | 303B | THREE HOLE - 0.141 INCH |
| DR01697 | 304B | THREE HOLE - 0.200 INCH |
| DR01700 | 305B | THREE HOLE - 0.250 INCH |
| DR01701 | 306B | THREE HOLE - 0.291 INCH |
| DR01703 | 307B | THREE HOLE - 0.350 INCH |
| DR01693 | 308B | THREE HOLE - 0.115 INCH |
| DR01695 | 309B | THREE HOLE - 0.150 INCH |
| DR01696 | 310B | THREE HOLE - 0.180 INCH |
| DR01698 | 311B | THREE HOLE - 0.230 INCH |
| DR01699 | 312B | THREE HOLE - 0.243 INCH |
| DR01702 | 313B | THREE HOLE - 0.300 INCH |
| DR01704 | 314B | THREE HOLE - 0.200-0.220 |
| DR01705 | 315B | THREE HOLE - 0.190-0.165 |
| BX10111 | 316B | THREE HOLE |
| DR00846 | 3200B | THIRTY TWO HOLE - 0.600 INCH |
| DR00847 | 3201B | THIRTY TWO HOLE - 0.624 INCH |
| DR00848 | 3202B | THIRTY TWO HOLE - 0.750 INCH |
| DR00887 | 3203B | THIRTY TWO HOLE - 0.100 INCH |
| DR00888 | 3204B | THIRTY TWO HOLE - 0.200 INCH |
| DR00889 | 3600B | THIRTY TWO HOLE - 0.600 INCH |
| DR00890 | 3601B | THIRTY SIX HOLE - 0.625 INCH |
| DR00891 | 3602B | THIRTY SIX HOLE - 0.750 INCH |
| BX10008 | 3603B | THIRTY SIX HOLE |
| BX10009 | 3604B | THIRTY SIX HOLE |
| DR00895 | 3605B | THIRTY SIX HOLE - 0.100 INCH |
| DR00896 | 3606B | THIRTY SIX HOLE - 0.200 INCH |
| DR00843 | 4000B | FORTY HOLE - 0.600 INCH |
| DR00844 | 4001B | FORTY HOLE - 0.625 INCH |
| DR00845 | 4002B | FORTY HOLE - 0.750 INCH |
| BX10099 | 400B | FOUR HOLE |
| DR01607 | 401B | FOUR HOLE - 0.200 INCH |
| DR01610 | 402B | FOUR HOLE - 0.250 INCH |
| DR01611 | 403B | FOUR HOLE - 0.291 INCH |
| DR01613 | 404B | FOUR HOLE - 0.350 INCH |
| DR01624 | 405B | FOUR HOLE - 0.100 INCH |
| DR01626 | 406B | FOUR HOLE - 0.141 INCH |
| DR01631 | 407B | FOUR HOLE - 0.250 INCH |
| DR01633 | 408B | FOUR HOLE - 0.291 INCH |
| DR01634 | 409B | FOUR HOLE - 0.350 INCH |
| DR01604 | 410B | FOUR HOLE - 0.100 INCH |
| DR01605 | 411B | FOUR HOLE - 0.150 INCH |
| DR01606 | 412B | FOUR HOLE - 0.180 INCH |
| DR01608 | 413B | FOUR HOLE - 0.230 INCH |
| DR01609 | 414B | FOUR HOLE - 0.243 INCH |
| DR01612 | 415B | FOUR HOLE - 0.300 INCH |
| DR01625 | 416B | FOUR HOLE - 0.115 INCH |
| DR01627 | 417B | FOUR HOLE - 0.150 INCH |
| DR01628 | 418B | FOUR HOLE - 0.180 INCH |
| DR01629 | 419B | FOUR HOLE - 0.200 INCH |
| BX10002 | 4200B | FORTY TWO HOLE |
| DR01630 | 420B | FOUR HOLE - 0.230 INCH |
| DR01632 | 421B | FOUR HOLE - 0.282 INCH |
| DR01635 | 422B | FOUR HOLE - 0.376 INCH |
| DR01636 | 423B | FOUR HOLE - 0.406 INCH |
| DR01637 | 424B | FOUR HOLE - 0.415 INCH |
| DR01638 | 425B | FOUR HOLE - 0.687 INCH |
| DR01639 | 426B | FOUR HOLE - 0.971 INCH |
| BX10102 | 427B | FOUR HOLE |
| BX10103 | 428B | FOUR HOLE |
| DR01657 | 429B | FOUR HOLE - 0.100 INCH |
| DR01658 | 430B | FOUR HOLE - 0.200 INCH |
| BX10105 | 431B | FOUR HOLE |
| DR01597 | 432B | FOUR HOLE - 0.958 - 0.190 |
| DR01598 | 433B | FOUR HOLE - 1.177-.420 |
| BX10003 | 4800B | FORTY EIGHT HOLE |
| BX10246 | 500B | FIVE HOLE |
| BX10091 | 501B | FIVE HOLE |
| DR01601 | 502B | FIVE HOLE - 0.048 INCH |
| DR01602 | 503B | FIVE HOLE - 0.100 INCH |
| DR01603 | 504B | FIVE HOLE - 0.200 INCH |
| BX10093 | 505B | FIVE HOLE |
| DR01507 | 506B | FIVE HOLE - 0.100 INCH |
| DR01508 | 507B | FIVE HOLE - 0.115 INCH |
| DR01509 | 508B | FIVE HOLE - 0.141 INCH |
| DR01510 | 509B | FIVE HOLE - 0.150 INCH |
| DR01511 | 510B | FIVE HOLE - 0.180 INCH |
| DR01515 | 511B | FIVE HOLE - 0.291 INCH |
| DR01516 | 512B | FIVE HOLE - 0.350 INCH |
| DR01512 | 513B | FIVE HOLE - 0.200 INCH |
| DR01513 | 514B | FIVE HOLE - 0.250 INCH |
| DR01514 | 515B | FIVE HOLE - 0.282 INCH |
| DR01517 | 516B | FIVE HOLE - 0.376 INCH |
| DR01518 | 517B | FIVE HOLE - 0.406 INCH |
| DR01526 | 600B | SIX HOLE - 0.141 INCH |
| DR01527 | 601B | SIX HOLE - 0.200 INCH |
| DR01531 | 602B | SIX HOLE - 0.291 INCH |
| DR01533 | 603B | SIX HOLE - 0.350 INCH |
| DR01537 | 604B | SIX HOLE - 0.141 INCH |
| DR01538 | 605B | SIX HOLE - 0.200 INCH |
| DR01543 | 606B | SIX HOLE - 0.310 INCH |
| DR01544 | 607B | SIX HOLE - 0.350 INCH |
| DR01525 | 608B | SIX HOLE - 0.100 INCH |
| DR01528 | 609B | SIX HOLE - 0.230 INCH |
| DR01529 | 610B | SIX HOLE - 0.243 INCH |
| DR01530 | 611B | SIX HOLE - 0.250 INCH |
| DR01532 | 612B | SIX HOLE - 0.312 INCH |
| DR01534 | 613B | SIX HOLE - 0.400 INCH |
| DR01535 | 614B | SIX HOLE - 0.406 INCH |
| BX10088 | 615B | SIX HOLE - 0.100 INCH |
| DR01539 | 616B | SIX HOLE - 0.230 INCH |
| DR01540 | 617B | SIX HOLE - 0.243 INCH |
| DR01541 | 618B | SIX HOLE - 0.250 INCH |
| DR01542 | 619B | SIX HOLE - 0.291 INCH |
| DR01545 | 620B | SIX HOLE - 0.400 INCH |
| DR01546 | 621B | SIX HOLE - 0.406 INCH |
| DR01570 | 622B | SIX HOLE - 0.300 INCH |
| DR01572 | 623B | SIX HOLE - 1.300 INCH |
| DR01571 | 624B | SIX HOLE - 0.450 INCH |
| BX10082 | 700B | SEVEN HOLE |
| DR01310 | 701B | SEVEN HOLE - 0.200 INCH |
| DR01314 | 702B | SEVEN HOLE - 0.291 INCH |
| DR01316 | 703B | SEVEN HOLE - 0.350 INCH |
| DR01422 | 704B | SEVEN HOLE - 0.200 INCH |
| DR01427 | 705B | SEVEN HOLE - 0.310 INCH |
| DR01428 | 706B | SEVEN HOLE - 0.350 INCH |
| DR01308 | 707B | SEVEN HOLE - 0.100 INCH |
| DR01309 | 708B | SEVEN HOLE - 0.141 INCH |
| DR01311 | 709B | SEVEN HOLE - 0.230 INCH |
| DR01312 | 710B | SEVEN HOLE - 0.243 INCH |
| DR01313 | 711B | SEVEN HOLE - 0.250 INCH |
| DR01315 | 712B | SEVEN HOLE - 0.312 INCH |
| DR01317 | 713B | SEVEN HOLE - 0.400 INCH |
| DR01318 | 714B | SEVEN HOLE - 0.406 INCH |
| DR01420 | 715B | SEVEN HOLE - 0.100 INCH |
| DR01421 | 716B | SEVEN HOLE - 0.141 INCH |
| DR01423 | 717B | SEVEN HOLE - 0.230 INCH |
| DR01424 | 718B | SEVEN HOLE - 0.243 INCH |
| DR01425 | 719B | SEVEN HOLE - 0.250 INCH |
| DR01426 | 720B | SEVEN HOLE - 0.291 INCH |
| DR01429 | 721B | SEVEN HOLE - 0.400 INCH |
| DR01430 | 722B | SEVEN HOLE - 0.406 INCH |
| BX10085 | 723B | SEVEN HOLE |
| BX10076 | 724B | SEVEN HOLE |
| BX10077 | 725B | SEVEN HOLE |
| BX10004 | 8000B | EIGHTY HOLE |
| BX10078 | 800B | EIGHT HOLE |
| BX10079 | 801B | EIGHT HOLE |
| BX10080 | 802B | EIGHT HOLE |
| BX10081 | 803B | EIGHT HOLE |
| BX10070 | 804B | EIGHT HOLE |
| DR01306 | 805B | EIGHT HOLE - 0.300 INCH |
| BX10071 | 806B | EIGHT HOLE |
| BX10073 | 807B | EIGHT HOLE |
| BX10074 | 808B | EIGHT HOLE |
| BX10075 | 809B | EIGHT HOLE |
| DR01307 | 810B | EIGHT HOLE - 0.450 INCH |
| DR01259 | 811B | EIGHT HOLE - 0.287-0.740 |
| BX10068 | 812B | EIGHT HOLE |
| DR01256 | 813B | EIGHT HOLE - 0.100 INCH |
| DR01257 | 814B | EIGHT HOLE - 0.200 INCH |
| DR01258 | 815B | EIGHT HOLE - 0.287-0.687 |
| DR01260 | 816B | EIGHT HOLE - 0.298-0.740 |
| DR01264 | 817B | EIGHT HOLE - 0.141 INCH |
| DR01265 | 818B | EIGHT HOLE - 0.200 INCH |
| DR01272 | 819B | EIGHT HOLE - 0.310 INCH |
| DR01274 | 820B | EIGHT HOLE - 0.350 INCH |
| DR01275 | 821B | EIGHT HOLE - 0.380 INCH |
| DR01266 | 822B | EIGHT HOLE - 0.230 INCH |
| DR01267 | 823B | EIGHT HOLE - 0.243 INCH |
| DR01268 | 824B | EIGHT HOLE - 0.250 INCH |
| DR01269 | 825B | EIGHT HOLE - 0.260 INCH |
| DR01270 | 826B | EIGHT HOLE - 0.273 INCH |
| DR01271 | 827B | EIGHT HOLE - 0.291 INCH |
| DR01273 | 828B | EIGHT HOLE - 0.328 INCH |
| DR01276 | 829B | EIGHT HOLE - 0.400 INCH |
| DR01277 | 830B | EIGHT HOLE - 0.812 INCH |
| DR01278 | 831B | EIGHT HOLE - 1.125 INCH |
| BX10061 | 900B | NINE HOLE |
| BX10062 | 901B | NINE HOLE |
| BX10063 | 902B | NINE HOLE |
| BX10064 | 903B | NINE HOLE |
| DR01228 | 904B | NINE HOLE - 0.200 INCH |
| DR01235 | 905B | NINE HOLE - 0.310 INCH |
| DR01237 | 906B | NINE HOLE - 0.350 INCH |
| DR01254 | 907B | NINE HOLE - 0.100 INCH |
| DR01255 | 908B | NINE HOLE - 0.200 INCH |
| DR01227 | 909B | NINE HOLE - 0.141 INCH |
| DR01229 | 910B | NINE HOLE - 0.230 INCH |
| DR01230 | 911B | NINE HOLE - 0.243 INCH |
| DR01231 | 912B | NINE HOLE - 0.250 INCH |
| DR01232 | 913B | NINE HOLE - 0.260 INCH |
| DR01233 | 914B | NINE HOLE - 0.273 INCH |
| DR01234 | 915B | NINE HOLE - 0.291 INCH |
| DR01236 | 916B | NINE HOLE - 0.328 INCH |
| DR01238 | 917B | NINE HOLE - 0.380 INCH |
| DR01239 | 918B | NINE HOLE - 0.400 INCH |
| DR01240 | 919B | NINE HOLE - 0.812 INCH |
| DR01241 | 920B | NINE HOLE - 1.125 INCH |
| DR01215 | 921B | NINE HOLE - 0.390 INCH |
| DR01216 | 922B | NINE HOLE - 0.572 INCH |
| DR01217 | 923B | NINE HOLE - 0.781 INCH |
| DR01218 | 924B | NINE HOLE - 0.810 INCH |
| DR01219 | 925B | NINE HOLE - 0.836 INCH |
CZGY*AACCOMMODATED DEVICE MOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES ACCOMMODATED ON THE DEVICE.
Enter the numeric reply with a minimum of one digit.
(CZGYA10*)
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (AEBV)
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (ABVG)
IF STYLE/REPLY CODE(s) AAC, ABW, ACE, AET, AHF, ALF OR BWB WERE ENTERED FOR MRC AXHR, YOU MUST ANSWER MRC (THSD)
AXHRJMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(AXHR3ATDJAHD2*;AXHR3ATDJAHD2$$JAHD3*;AXHR3ATDJAHD2$JAHD2*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AM39) | Reply |
| BTZ | BAIL HANDLE |
| ABB | BASE |
| AAC | BOLT |
| ABC | BRACKET(S) |
| ABH | CLAMP |
| AFL | CLIP |
| AFQ | CONNECTOR |
| ACR | FLANGE |
| ABL | FRICTION |
| BWA | LAG(S) |
| BDK | LOOP(S) |
| AHN | MAGNETIC |
| BWB | NUT PLATE(S) |
| ABP | PLUG-IN |
| AAG | RIVET |
| ABW | SCREW |
| ALF | SELF-LOCKING NUT |
| ABY | SLOT |
| AHA | SOLDER |
| AER | SPRING |
| ACB | STRAP(S) |
| AAE | STUD(S) |
| ACC | TAB |
| ACE | THREADED BASE |
| AHF | THREADED HOLE(S) |
| AET | THREADED STUD(S) |
| AHD | TWIST LOCK |
| ACQ | UNTHREADED HOLE(S) |
| AEW | UNTHREADED STUD |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBV3AEEJAC2.0*;AEBV3AEEJAC2.0$JAC2.0*;AEBV3AEEJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVG3BHKJAC2.0*;ABVG3BHKJAC2.0$JAC2.0*;ABVG3BHKJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CTTC) or (CQJX and CQQR) or (CQJX)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CTTC and CQQR)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and CMLP)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD)
IF STYLE/REPLY CODE(s) JS OR NS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and CMLP) or (CQJX and CMLP)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX and CQQR)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(THSD3ASZDJE*;THSD3ASZDJE$DEM*;THSD3ASZDJE$$DEM*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NM | UNM |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJX3ATDJA2.0*;CQJX3ATDJA2.0$JA2.0*;CQJX3ATDJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(AAJD3BHKAX6)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CTTC3AEEJNTE2.0*;CTTC3AEEJNTE2.0$JNTE2.0*;CTTC3AEEJNTE2.0$$JNTE2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CMLP3BHKAQ1)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3BHK | ALL MOUNTING FACILITIES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(CQQR3ASZB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBCR*;CBBLDBWQ$$DAAJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| ASQ | ADJUSTABLE |
| BCW | ANGLE BRACKET ENDS |
| BZP | BOLT |
| BGH | BRACKET |
| AMR | CLIP |
| BBA | COUNTERBORED BOLT HOLES |
| BHM | DETACHABLE MOUNTING BRACKET |
| CQW | FLAT WASHER |
| BBR | FLOATING NUT |
| BQN | GASKET |
| ALW | GROMMET |
| DRG | LEFT HAND LOCK |
| BZW | LOCK |
| DRH | LOCK RETAINER TAB |
| AFY | LOCK WASHER |
| AKG | LOCKING DEVICE |
| BBL | LOCKNUT |
| ARA | MOUNTING BRACKET |
| AAJ | MOUNTING HARDWARE |
| AFZ | NUT |
| DRK | PLAIN LOCKING |
| BWQ | RADIATION HARDENED |
| CQY | RETAINING CLIP |
| DRJ | RIGHT HAND LOCK |
| AGC | SCREW |
| ALX | SEAL |
| CQZ | SHIM |
| BFT | SHOCK MOUNTS |
| BCR | SLOTTED |
| CRB | SPACER |
| BRP | SPECIAL MARKING |
| BAY | SPRING LOADED |
| CRC | SQUARE NUT |
| BQE | W/SPRING |
| BEQ | WASHER |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAGA000*;PRMTDRHA000$DIRA000*;PRMTDRHA000$$DIRA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000E2.0*;PMWTJAUA000E2.0$JAUA000E2.0*;PMWTJAUA000E2.0$$JAUA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| C | CARAT |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJRHA0002.0*;PMLCJRHA0002.0$JRHA0002.0*;PMLCJRHA0002.0$$JRHA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ008*;HZRDDHAZ042$$DHAZ030*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ008 | CADMIUM |
| HAZ030 | MAGNESIUM ALLOY |
SHPN*ADOT PROPER SHIPPING NAME
THE PROPER SHIPPING NAME AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE.
Enter the alpha-numeric reply with a minimum of one character.
(SHPNAI6)
DENN*ADOT IDENTIFICATION NUMBER
THE IDENTIFICATION NUMBER ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PROPER SHIPPING NAME. IDENTIFICATION NUMBERS PRECEDED BY THE LETTERS "UN" ARE ASSOCIATED WITH INTERNATIONAL AS WELL AS DOMESTIC TRANSPORTATION AND THOSE PRECEDED BY THE LETTERS "NA" ARE NOT RECOGNIZED FOR INTERNATIONAL TRANSPORTATION OF HAZARDOUS MATERIALS (DANGEROUS GOODS) EXCEPT TO AND FROM THE UNITED STATES AND CANADA.
Enter the alpha-numeric reply with a minimum of one character.
(DENNAV2)
WLBL*ADOT WARNING LABEL CODE
THE WARNING LABEL CODE ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PACKAGE OR CONTAINMENT DEVICE OFFERED FOR TRANSPORTATION OF A HAZARDOUS MATERIAL WHICH MEETS ONE OR MORE HAZARD CLASS DEFINITIONS IN ACCORDANCE WITH THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE. THIS MRC HAS BEEN DISCONTINUED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG G OF THE TIR.
Enter the alpha-numeric reply with a minimum of one character.
(WLBLAN6)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information