Table 1
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

Table 2
	Reply Code (AE09)	Reply
	B	COMPOSITION
	M	CONDUCTIVE PLASTIC
	C	FILM
	N	HYBRID
	D	WIRE WOUND

CQCCJELECTRICAL RESISTANCE PER SECTION

A MEASURE OF THE OPPOSITION TO THE FLOW OF DIRECT OR ALTERNATING CURRENT PER SECTION.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CQCCJKZCY2.0*;CQCCJKZCY2.0$$JKZCY2.1*)

Table 1
	Reply Code (AN86)	Reply
	GZ	GIGOHMS
	KZ	KILOHMS
	MZ	MEGOHMS
	ZZ	OHMS

Table 2
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

CRSSJRESISTANCE TOLERANCE PER SECTION IN PERCENT

THE LIMITS OF PERMISSIBLE VARIATION IN THE ELECTRICAL RESISTANCE VALUE PER SECTION OF AN ITEM FROM ITS RATED VALUE,EXPRESSED IN PERCENT.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.

(CRSSJCRM32.0/P50.0*;CRSSJCRM32.0/P50.0$$JCR*)

Table 1
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

CYEJ*HSTANDARD TAPER CURVE PER SECTION

THE RATE OF CHANGE AND DISTRIBUTION OF RESISTANCE PER SECTION,IN RELATION TO THE ROTATION OF THE CONTROL SHAFT,WHICH ESTABLISHES A STANDARD TAPER CURVE DESIGNATED BY AN ALPHABETIC CHARACTER AND ACCEPTED FOR COMMON USAGE.

Enter the applicable Reply Code from Tables 1 & 2 below.

(CYEJHCRFN2.0*;CYEJHCRFN2.0$$HCRFN2.1*)

Table 1
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

Table 2
	Reply Code (AF63)	Reply
	AG	LINEAR
	FL	MODIFIED CCW LOGARITHMIC
	FM	MODIFIED CW LOGARITHMIC
	FN	MODIFIED LINEAR

CRGM*HFUNCTION CONFORMITY PER SECTION

THE FIDELITY OF THE RELATIONSHIP BETWEEN THE ACTUAL FUNCTION CHARACTERISTICS AND THE THEORETICAL FUNCTION PER SECTION.

Enter the applicable Reply Code from Tables 1 & 2 below.

(CRGMHEQD2.0*;CRGMHEQD2.0$$HEQD2.1*)

Table 1
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

Table 2
	Reply Code (AC86)	Reply
	F	ABSOLUTE CONFORMITY
	E	ABSOLUTE LINEARITY
	B	INDEPENDENT LINEARITY
	G	PROPORTIONAL CONFORMITY
	H	STEPPED CONFORMITY
	D	TERMINAL BASE LINEARITY
	C	ZERO BASED LINEARITY

CSBX*HFUNCTION CHARACTERISTIC PER SECTION

THE SPECIFIED MATHEMATICAL RELATION PER SECTION BETWEEN THE TERMINAL RESISTANCE,OR OUTPUT RATIO,AND THE ROTATION OF THE ACTUATOR.

Enter the applicable Reply Code from Tables 1 & 2 below.

(CSBXHCXAH2.0*;CSBXHCXAH2.0$$HCXAH2.1*)

Table 1
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

Table 2
	Reply Code (AC85)	Reply
	AF	180 DEG SINE
	AK	20 DB LOG.
	AD	360 DEG COSINE
	AC	360 DEG SINE
	AB	360 DEG SINE-COSINE
	AL	40 DB LOG.
	AM	50 DB LOG.
	AH	90 DEG SINE
	AE	DOUBLE SIDED SQUARE
	AQ	EQUATION
	AP	GRAPH
	AA	LINEAR
	AG	SINGLE SIDED SQUARE
	AN	TABLE
	AJ	TANGENTIAL PORM 75 DEG

CQFL*JFUNCTION CONFORMITY TOLERANCE PER SECTION

THE PERMISSIBLE RANGE PER SECTION BY WHICH THE ACTUAL VALUE OF RESISTANCE OR VOLTAGE AT ANY SPECIFIED POINT MAY DEVIATE FROM THE THEORETICAL VALUE FOR THE LINEAR OR NONLINEAR FUNCTION,EXPRESSED AS A MINUS AND PLUS PERCENT.

(CQFLJEPM32.0/P50.0*;CQFLJEPM32.0/P50.0$$JEP*)

Table 1
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

CRGDJPOWER DISSIPATION RATING PER SECTION IN WATTS

THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED PER SECTION,EXPRESSED IN WATTS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CRGDJBCZ2.0*;CRGDJBCZ2.0$$JBCZ2.1*)

Table 1
	Reply Code (AC89)	Reply
	B	FREE AIR
	C	HEAT SINK

Table 2
	Reply Code (AH19)	Reply
	DA	10TH SECTION
	EM	11TH SECTION
	EN	12TH SECTION
	EP	13TH SECTION
	EQ	14TH SECTION
	ER	15TH SECTION
	CP	1ST SECTION
	CQ	2ND SECTION
	CR	3RD SECTION
	CS	4TH SECTION
	CT	5TH SECTION
	CW	6TH SECTION
	CX	7TH SECTION
	CY	8TH SECTION
	CZ	9TH SECTION
	CM	ALL SECTIONS
	CN	SINGLE SECTION

IF STYLE/REPLY CODE(s) 1A, 3A, 5A, 7A, 9A OR 10A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ABPM and ADAP)

IF STYLE/REPLY CODE(s) 2A OR 4A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ABPM)

IF STYLE/REPLY CODE(s) 6A OR 8A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADAQ and ADAP and ADAT and ADAU)

AAQLLBODY STYLE

THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.

Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.

(AAQLL10A)

Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
AAO1356	10A	CYLINDRICAL BUSHING MOUNTED
AAO1347	1A	CYLINDRICAL BUSHING MOUNTED
AAO1348	2A	CYLINDRICAL SERVO MOUNTED
AAO1349	3A	CYLINDRICAL BUSHING MOUNTED
AAO1350	4A	CYLINDRICAL SERVO MOUNTED
AAO1351	5A	CYLINDRICAL BUSHING MOUNTED
AAO1352	6A	RECTANGULAR BUSHING MOUNTED
AAO1353	7A	CYLINDRICAL BUSHING MOUNTED
AAO1354	8A	RECTANGULAR BUSHING MOUNTED
AAO1355	9A	CYLINDRICAL BUSHING MOUNTED

ABPM*JBODY DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABPMJAA2.0*;ABPMJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADAQ*JBODY LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAQJAA2.0*;ADAQJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADAT*JBODY WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADATJAB2.0*;ADATJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADAU*JBODY HEIGHT

A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAUJAA2.0*;ADAUJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADAP*JMOUNTING BUSHING LENGTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAPJAA2.0*;ADAPJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

IF STYLE/REPLY CODE(s) 1B, 3B, 4B, 5B, 6B, 7B, 8B, 12B, 13B, 14B, 15B, 18B, 22B, 23B, 24B, 27B, 29B, 30B, 31B, 33B, 34B, 40B, 41B, 43B, 46B, 53B, 54B OR 56B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABWV and ABXF)

IF STYLE/REPLY CODE(s) 2B, 9B, 10B, 21B, 25B, 32B, 36B, 42B, 44B, 48B, 49B, 50B, 52B OR 55B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABNC and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 11B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (AEDS and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 16B OR 17B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (AEDQ and AGQL and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 19B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (AEDQ and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 20B OR 26B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 28B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ADAS and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 35B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (AEDH and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 37B OR 51B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (AEDS and ABXF)

IF STYLE/REPLY CODE(s) 38B OR 39B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNB and AEDS and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 45B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABND and ABXF and ABWV)

IF STYLE/REPLY CODE(s) 47B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABNE and ABNB and AEDQ and ABNC and AGQL and ABXF and CXJQ and ABWV)

IF STYLE/REPLY CODE(s) 57B OR 58B WERE ENTERED FOR MRC AEDX, YOU MUST ANSWER MRC (ABXF and ABNB and ABNC and AATB and ABWV)

AEDXLSHAFT STYLE

THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SHAFT.

(AEDXL10B)

Table 1
Physical Drawing ID	Reply Code (STYL)	Reply
DQ00078	10B	ROUND, PARALLEL, FLATTED
DQ00079	11B	ROUND, SQUARE
DQ00080	12B	ROUND, MILLED, SPRING SLIT
DQ00081	13B	ROUND, KNURLED
DQ00082	14B	ROUND, SLOTTED, KNURLED
AAO1357	15B	ROUND, MILLED
AAO1358	16B	ROUND, STEPPED, KNURLED
AAO1359	17B	ROUND, STEPPED
AAO1360	18B	ROUND, STEPPED, UNDERCUT
AAO1361	19B	ROUND, SLOTTED, STEPPED, MILLED, UNDERCUT
DQ00069	1B	ROUND
AAO1362	20B	ROUND, V FLATTED
AAO1363	21B	ROUND, WEDGE, FLATTED
AAO1364	22B	ROUND, T SLOTTED
AAO1365	23B	ROUND, TAPERED DOUBLE FLAT
AAO1366	24B	ROUND, CROSS SLOTTED
AAO1367	25B	ROUND, TAPERED FLAT
AAO1368	26B	ROUND, NON-PARALLEL FLATTED
AAO1369	27B	ROUND, PARALLEL FLATTED, SINGLE FLATTED
AAO1370	28B	ROUND, HOLLOW
AAO1371	29B	ROUND, HOLLOWED, SLOTTED
DQ00070	2B	ROUND, FLATTED
AAO1372	30B	ROUND, DOUBLE GROOVED
AAO1373	31B	ROUND, SQUARE CHANNELED
AAO1374	32B	ROUND, FLATTED FURROWED
AAO1375	33B	ROUND, DOUBLE V CHANNELED
AAO1376	34B	ROUND, V CHANNELLED
AAO1377	35B	ROUND, U CHANNELLED
AAO1378	36B	ROUND, FLATTED, TRIPLE FURROWED
AAO1379	37B	SQUARE
AAO1380	38B	ROUND, SQUARED SLOTTED
AAO1381	39B	ROUND, SQUARED, V CHANNELLED
DQ00071	3B	ROUND, SLOTTED
AAO1382	40B	ROUND, BEVEL GEARED END
AAO1383	41B	ROUND, FLUTTED
AAO1384	42B	ROUND, FLATTED, FLUTED
AAO1385	43B	ROUND, FLATTED, KNURLED GROOVED
AAO1386	44B	ROUND, SLOTTED, PARALLEL FLATTED
AAO1387	45B	ROUND TAPERED
AAO1388	46B	HEXAGON SHAPE
AAO1389	47B	ROUND, STEPPED, FLATTED
AAO1390	48B	ROUND, FLATTED W/THRU HOLE
AAO1391	49B	ROUND, HOLLOWED, FLATTED
DQ00072	4B	FLAT, ROUND UNDERCUT
AAO1392	50B	ROUND, PARALLEL FLATTED, THREADED HOLE
AAO1393	51B	SQUARE, THREADED HOLE
AAO1394	52B	ROUND, SQUARE, THREADED HOLE
AAO1395	53B	ROUND, THREADED HOLE
AAO1396	54B	ROUND, W/THRU HOLE
AAO1397	55B	ROUND, FLATTED, THREADED HOLE
AAO1398	56B	ROUND, FLUTTED THREADED HOLE
AAO1399	57B	ROUND, TRIPLE FLATTED, THREADED HOLE
AAO1400	58B	ROUND, TRIPLE FLATTED
DQ00073	5B	ROUND, UNDERCUT
DQ00074	6B	ROUND, SLOTTED, UNDERCUT
DQ00075	7B	ROUND, SLOTTED, UNDERCUT
DQ00076	8B	ROUND, THREADED
DQ00077	9B	ROUND, SLOTTED, FLATTED

AATB*JWIDTH BETWEEN FLATS

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AATBJAA2.0*;AATBJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABNB*JFIRST FLAT LENGTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABNBJAC2.0*;ABNBJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABNC*JFLAT HEIGHT

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABNCJAB2.0*;ABNCJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABND*JTAPER LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF THE TAPERED PORTION OF AN ITEM,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABNDJAB2.0*;ABNDJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABNEJSECOND FLAT LENGTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABNEJAC2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABWV*JSHAFT DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABWVJAB2.0*;ABWVJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABXF*JSHAFT LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABXFJAB2.0*;ABXFJAB2.0$$JAB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ADAS*JBODY INSIDE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADASJAA2.0*;ADASJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEDH*JCHANNEL LENGTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEDHJAC2.0*;AEDHJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEDQ*JUNDERCUT DIAMETER

NONE. PLEASE USE MRC ABPA IN PLACE OF THIS DISCONTINUED MRC.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEDQJAC2.0*;AEDQJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEDSJSQUARE SHAFT WIDTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEDSJAC2.0*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AGQL*JUNDERCUT LENGTH

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AGQLJAA2.0*;AGQLJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

CXJQ*JSECOND FLAT HEIGHT

NONE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CXJQJAC2.0*;CXJQJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AEFH*JEFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION

THAT PART OF THE TOTAL ROTATIONAL TRAVEL OF THE ACTUATOR THAT PRODUCES A CHANGE IN OUTPUT,EXPRESSED IN DEGREE ANGULAR ROTATION.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AEFHJC2.0*;AEFHJC2.0$$JC2.1*)

Table 1
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

IF STYLE/REPLY CODE(s) AGM OR AJN WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AJYP and AJYQ and AJYN)

IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and ABTD)

IF STYLE/REPLY CODE(s) AHF WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and AJYP and AJYQ and AJYN)

IF STYLE/REPLY CODE(s) AET WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and AJYP and AJYQ and AJYN and ADAG)

IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and ABTB)

AXGYDMOUNTING METHOD

THE MEANS OF ATTACHING THE ITEM.

Enter the applicable reply code from the table below

(AXGYDAGM*;AXGYDANF$$DACQ*)

Table 1
	Reply Code (AM39)	Reply
	ABC	BRACKET
	ACX	CLAMP RING
	ACR	FLANGE
	ABL	FRICTION
	AGM	LOCKING BUSHING
	ABY	SLOT
	ANF	SPRING CLIP
	AJN	STANDARD BUSHING
	ACD	TERMINAL
	AHF	THREADED HOLE
	AET	THREADED STUD
	ACQ	UNTHREADED HOLE

AKPV*AMOUNTING FACILITY QUANTITY

THE NUMBER OF MOUNTING FACILITIES PROVIDED.

Enter the numeric reply with a minimum of one digit.

(AKPVA10*)

ABTB*JMOUNTING HOLE DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABTBJAA2.0*;ABTBJAA2.0$$JAA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABTD*JMOUNTING SLOT WIDTH

A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABTDJAC2.0*;ABTDJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE, NF, NJ OR UN WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (AJYN and AJYQ)

IF STYLE/REPLY CODE(s) BF WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (AJYN)

IF STYLE/REPLY CODE(s) NM, NS, SM OR SS WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (AJYN and CQQR)

AJYP*DSCREW THREAD SERIES DESIGNATOR

A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.

Enter the applicable reply code from the table below

(AJYPDNM*;AJYPDJC$$DUN*)

Table 1
	Reply Code (AH06)	Reply
	BF	BSF
	SM	ISO M
	SS	ISO S
	UN	UN
	NC	UNC
	NE	UNEF
	NF	UNF
	NJ	UNJ
	JC	UNJC
	JE	UNJEF
	JF	UNJF
	NM	UNM
	NS	UNS

AJYN*JSCREW THREAD DIAMETER

THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COAXIAL CYLINDER WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(AJYNJAC2.0*;AJYNJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

CQQR*BTHREAD PITCH IN MILLIMETERS

A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(CQQRB2.0*;CQQRB2.02.0$BM2.0*)

AJYQ*BSCREW THREAD QUANTITY PER INCH

THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS,INCLUDING INCOMPLETE THREADS.

Enter a reply with a minimum of one digit on either side of the decimal point.

(AJYQB2.0*;AJYQB2.0$$BM2.0*)

ADAG*JMOUNTING STUD LENGTH

A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING STUD,IN DISTINCTION FROM WIDTH.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAGJAC2.0*;ADAGJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

CBBL*DFEATURES PROVIDED

THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.

Enter the applicable reply code from the table below

(CBBLDASF*;CBBLDAAR$$DCNW*)

Table 1
	Reply Code (AN47)	Reply
	AAR	NONMETALLIC SHAFT
	ASF	PANEL SEAL
	AAS	SHAFT LOCKING DEVICE
	CNW	SHAFT SEAL

ANJNDMOTOR TYPE

INDICATES THE TYPE OF MOTOR PROVIDED.

Enter the applicable reply code from the table below

(ANJNDAAD)

Table 1
	Reply Code (AJ71)	Reply
	AAD	AC HYSTERESIS
	AAH	INDUCTION
	AAQ	NONSYNCHRONOUS
	AAK	PERMANENT MAGNET
	AAB	SERIES-GOVERNED
	AAL	SERVO
	AAC	SYNCHRONOUS

CYEHJMOTOR VOLTAGE TYPE AND RATING IN VOLTS

INDICATES THE TYPE OF ELECTRICAL VOLTAGE AND RATING FOR WHICH THE MOTOR WAS DESIGNED,EXPRESSED IN VOLTS.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(CYEHJAC2.0*;CYEHJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AN87)	Reply
	AC	AC
	DC	DC

CYEKBGEAR RATIO

INDICATES THE RATIO OF THE OUTPUT GEAR TO THE INPUT GEAR.

Enter a reply with a minimum of one digit on either side of the decimal point.

(CYEKB2.0)

TTQYJTERMINAL TYPE AND QUANTITY

INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.

Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.

(TTQYJAAM2*;TTQYJAAM2$$JAAM3*)

Table 1
	Reply Code (AN89)	Reply
	AAF	CONNECTOR, RECEPTACLE
	AAM	PIN
	AAS	SOLDER STUD
	ABX	TAB W/SCREW
	ABB	TAB, SOLDER LUG
	ACC	WIRE LEAD
	ACD	WIRE LOOP

PMLC*JPRECIOUS MATERIAL AND LOCATION

AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.

Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.

(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)

Table 1
	Reply Code (MA01)	Reply
	AUA000	GOLD
	IRA000	IRIDIUM
	AZA000	OSMIUM
	PDA000	PALLADIUM
	PTA000	PLATINUM
	RHA000	RHODIUM
	RTA000	RUTHENIUM
	AGA000	SILVER

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	CS	CONSTRUCTION
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	FN	FINISH
	FM	FORM
	FA	FORMULA
	GR	GRADE
	GP	GROUP
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LT	LIMIT
	MK	MARK
	AA	MARKER
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	NR	NUMBER
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	QA	QUALITY
	RN	RANGE
	RT	RATING
	RF	REFERENCE NUMBER
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH