An indicator for the display of current meteorological information. It is a component of a meteorological data display set.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED60645*)
ALBY*DUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDBQA*;ALBYDBLE$$DBKH*)
| Table 1 |
| Reply Code (AH21) | Reply |
| BJH | AILERON TRIM |
| BJJ | AIR SPEED |
| BJK | AIRPORT RUNWAY LINE-UP ANGLE |
| BJL | ALTITUDE |
| BJM | ANCHOR ORDER |
| BJP | ANGLE OF ATTACK |
| BJN | ANTENNA HORN |
| BJQ | AZIMUTH RANGE |
| BJR | BANK ANGLE |
| BJS | BINARY CODING DECIMAL |
| BJT | CAUTION RANGE DATA |
| BJU | CHANNEL ALIGNMENT-PORTABLE RADIO |
| BJV | COURSE-STEERING ORDER |
| BJW | CYLINDER HEAD |
| BJX | DIRECTIONAL GYROSCOPIC |
| BJY | DISPLAY FUNCTION |
| BJZ | DISPLAY MODE |
| BKA | ELEVATOR TRIM |
| BKB | ENGINE ORDER |
| BKC | ENGINE PROPELLER ORDER |
| BKD | ENVIRONMENTAL ALARM |
| BKE | FIBER OPTICS |
| BKF | FILM SPEED |
| BKG | FLAG ROTARY |
| BKH | FLIGHT DIRECTOR |
| BKJ | GROUND SYSTEMS GROUP |
| BKK | GYRO COURSE |
| BKL | HANDHELD |
| BKM | HEADING |
| BKN | HELICOPTER ROTOR SYNCHRONISM |
| BKP | INDICATED AIR SPEED |
| BKQ | LIQUID OXYGEN QUANTITY |
| BKR | LOW APPROACH |
| BKS | MAGNETIC LATCHING TYPE |
| BKT | MASTER |
| BKU | MOTOR ORDER |
| BKV | OIL BURNER ORDER |
| BKX | PANEL ANGLE AUXILIARY |
| BKW | PANEL MOUNTED |
| BKY | PLANE ANGLE BOW |
| BKZ | PLANE ANGLE STERN |
| BLA | POSITION |
| BLB | PRESET CHANNEL |
| BLC | PROPELLER ORDER |
| BLD | PROPELLER REVOLUTION SHIPBOARD |
| BQA | RATE OF FLOW |
| BLS | RATE OF TURN |
| BLE | RECORDER |
| BLF | REPEATER |
| BLG | REVOLUTION FORCED DRAFT BLOWER |
| BLH | RUDDER ANGLE |
| BLJ | RUDDER ANGLE ORDER |
| BLW | RUDDER TRIM |
| BLK | SHIP COURSE |
| BLL | SHIP ENGINE ORDER |
| BLM | SHIP SPEED |
| BMG | SIMULATOR |
| BMH | SIMULATOR, SYSTEM LASER |
| BMJ | SIMULATOR, SYSTEM LASER, W/INTEGRAL POWER SOURCE |
| BLN | TABLE MODEL |
| BLP | TACHOMETER |
| ADX | TRANSMISSION LINE |
| BLQ | TRIM ANGLE |
| BLR | TRUE AIR SPEED |
| BLT | VERTICAL SPEED |
| ADY | WAVEGUIDE |
| BLU | WIND DIRECTION |
| BLV | WIND SPEED |
ASKX*AELECTRICAL CONNECTION QUANTITY
THE NUMBER OF ELECTRICAL CONNECTIONS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ASKXA10*)
AMNL*DPRESENTATION TYPE
INDICATES THE TYPE OF PRESENTATION.
Enter the applicable reply code from the table below
(AMNLDBD*;AMNLDBX$$DBK*)
| Table 1 |
| Reply Code (AJ15) | Reply |
| BK | ALARM |
| BL | AMMETER |
| BM | BUZZER |
| AK | CATHODE RAY TUBE |
| BN | CHART |
| AL | CIRCUIT |
| AM | COUNTER |
| AN | DIAL |
| BP | DIGITAL DISPLAY |
| BQ | DIGITAL MICROCIRCUIT DECODER |
| BR | DIPOLE PICK-UP |
| AP | DROP FLAGS |
| AQ | DRUM DIAL |
| BS | ELECTRON TUBE |
| BT | ELECTRONIC VIBRATOR |
| BU | FIBER OPTIC TRANSMISSION |
| BE | FLASHING LIGHT |
| BV | GALVANOMETER |
| AR | GRAPHIC RECORDER |
| AS | ILLUMINATED WINDOW |
| AT | INDICATOR LIGHT |
| AX | METER |
| BW | PULSED LASER LIGHT |
| BA | REGISTER |
| BX | SELSYN MOTOR |
| BD | SERVO MOTOR |
| BB | SYNCHRO MOTOR |
| BY | TOTALIZING COUNTER |
| AA | VIBRATOR ALARM |
| BZ | VOLTMETER |
| BC | WINDOW |
BFQN*DDISPLAY TYPE
INDICATES THE TYPE OF DISPLAY PROVIDED.
Enter the applicable reply code from the table below
(BFQNDFJT*;BFQNDFJS$$DFVW*)
| Table 1 |
| Reply Code (AK54) | Reply |
| FVW | BALLAST |
| FJS | FLUORESCENT TUBE |
| FJT | GAS DISCHARGE TUBE |
| FJW | LIGHT EMITTING DIODE (L.E.D.). |
| FJX | LIQUID CRYSTAL |
ASKN*GINDIVIDUAL MARKING
AN INDICATION OF THE INDIVIDUAL MARKING ON THE ITEM.
Enter clear text.
(ASKNGCLEARTEXT)
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(HUES3EQQDWH0027*;HUES3EQQDWH0027$DBL0001*;HUES3EQQDWH0027$$DBL0001*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EQQ | BACKGROUND OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD06) | Reply |
| AM0000 | AMBER |
| BL0000 | BLACK |
| BL0036 | BLACK, DULL |
| BL0001 | BLACK, FED STD 595, 17038 |
| BL0033 | BLACK, FED STD 595, 37038 |
| BL0039 | BLACK, LUSTERLESS |
| BU0000 | BLUE |
| CL0000 | CLEAR |
| GR0000 | GREEN |
| GR0466 | GREEN, MIL-STD-3009, NVIS TYPE I, CLASS A |
| GR0473 | GREEN, MIL-STD-3009, NVIS TYPE I, CLASS B |
| GR0474 | GREEN, MIL-STD-3009, NVIS TYPE II, CLASS A |
| GR0475 | GREEN, MIL-STD-3009, NVIS TYPE II, CLASS B |
| GR0079 | GREEN, MUNSELL |
| GR0035 | GREEN, PALE |
| RG0000 | ORANGE |
| RE0000 | RED |
| RE0081 | RED, AVIATION |
| RE0080 | RED, BLOOD |
| RE0077 | RED, DULL |
| WH0000 | WHITE |
| WH0034 | WHITE, DULL |
| WH0027 | WHITE, FED STD 595, 37875 |
| WH0019 | WHITE, OPAQUE |
| WH0012 | WHITE, TRANSLUCENT |
| YE0000 | YELLOW |
| YE0009 | YELLOW, PALE |
IF STYLE/REPLY CODE(s) C WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (ACYR)
IF STYLE/REPLY CODE(s) D WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (ACYR and ACYN and FAAZ and ACZB)
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC ACDC, YOU MUST ANSWER MRC (ACYN and FAAZ and ACZB)
ACDC*DCURRENT TYPE
INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.
Enter the applicable reply code from the table below
(ACDCDD)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| D | AC/DC |
| C | DC |
ACYR*JDC VOLTAGE RATING
THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYRJLA2.0*;ACYRJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AB63) | Reply |
| K | KILOVOLTS |
| M | MEGAVOLTS |
| U | MICROVOLTS |
| L | MILLIVOLTS |
| V | VOLTS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACYN*JAC VOLTAGE RATING
THE VALUE,OR RANGE OF VALUES,OF ROOT MEAN SQUARE POTENTIAL FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYNJUA2.0*;ACYNJUA2.0$$JUA2.1*)
| Table 1 |
| Reply Code (AB63) | Reply |
| K | KILOVOLTS |
| M | MEGAVOLTS |
| U | MICROVOLTS |
| L | MILLIVOLTS |
| V | VOLTS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDA*;FAAZDB$$DC*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| C | THREE |
| B | TWO |
ACZB*JFREQUENCY RATING
THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACZBJGB2.0*;ACZBJGB2.0$$JGB2.1*)
| Table 1 |
| Reply Code (AC32) | Reply |
| G | GIGAHERTZ |
| E | HERTZ |
| K | KILOHERTZ |
| M | MEGAHERTZ |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMND*JINPUT IMPEDANCE RATING
THE TOTAL OPPOSITION (RESISTIVE AND REACTIVE) PRESENTED BY THE ITEM TO AN ALTERNATING CURRENT SOURCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMNDJGFC2.0*;AMNDJGFC2.0$$JGFC2.1*)
| Table 1 |
| Reply Code (AE75) | Reply |
| GF | GIGOHMS |
| KR | KILOHMS |
| MR | MEGOHMS |
| QR | OHMS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASLN*JFUSE CURRENT RATING IN AMPS
THE VALUE OF CURRENT FOR WHICH THE FUSE IS RATED,EXPRESSED IN AMPERES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASLNJB2.0*;ASLNJB2.0$$JB2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAB2.0*;ABTBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVGJAB2.0*;ABVGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJFA2.0*;ABRYJFA2.0$$JFA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Y | YARDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJYB2.0*;ABGLJYB2.0$$JYB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Y | YARDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMZ*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMZJAA2.0*;ABMZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HGTH*JHEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(HGTHJAB2.0*;HGTHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJZ*JDEPTH
A LINEAR MEASUREMENT FROM THE SURFACE TO A SPECIFIED INNER POINT ON AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJZJAC2.0*;AEJZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCCD)
| Table 1 |
| Reply Code (AN47) | Reply |
| BGA | ADAPTER |
| CWB | ASPIRATOR BULB |
| CWC | BELL SIGNAL |
| CWD | BEZEL |
| CWE | CALIBRATION CHART |
| CWF | CARRYING CASE WITH STRAP |
| CWG | CHARCOAL CARTRIDGE |
| CWH | COAXIAL ADAPTER |
| CWJ | COIL |
| BEM | COVER |
| CWK | CRYSTAL |
| CWL | DECAL |
| CWM | DIFFUSION RING |
| CWN | DILUTION VALVE |
| CCD | DRY CELL BATTERY |
| CWP | DUMMY LOAD |
| BNM | ENCAPSULATED |
| CWQ | EXCESSIVE OVER-TEMPERATURE SIGNAL |
| CWR | FILAMENT |
| BJE | FORDING FEATURE |
| CEG | HANDHELD |
| AQK | HANDLE |
| CWS | HEAT SINK |
| AAH | HERMETICALLY SEALED CASE |
| CWT | HOSE CLAMP COUPLING |
| CWU | HOSE COUPLING NUT |
| CWV | HOSE COUPLING SLEEVE |
| CCH | INCANDESCENT LAMP |
| CCJ | INSTRUCTION MANUAL |
| CWW | INTEGRAL SYNCHROSCOPE |
| DLP | INTERNAL POWER PACK |
| CWX | KNURLED RING |
| CWY | LAMP SOCKET |
| CWZ | LINE TRAP |
| CXA | LOW PASS FILTER |
| ABH | MARKER STRIP |
| AAJ | MOUNTING HARDWARE |
| EUS | NIGHT VISION COMPATIBILITY |
| CXB | PACKING O-RING |
| CXC | PITOT PRESSURE INSERT |
| CFY | PORTABLE |
| CXD | POWER SUPPLY |
| CXE | PROBE TUBE |
| ALS | PROTECTIVE CAP |
| CXF | RADIO FREQUENCY PROBE ADAPTER |
| CXG | REFERENCE INDEX SETTING |
| CXJ | RESISTOR TYPE VOLTAGE ADAPTER |
| CXK | RETAINING RING |
| CXL | REVOLUTION COUNTER |
| CXM | SAMPLING LINE |
| CXN | SELECTOR SWITCH |
| CXP | STABILIZER |
| CXQ | STATIC PRESSURE INSERT |
| CXR | SYNCHRO MOUNTING CLAMP |
| CXS | TECHNICAL MANUAL |
| BMS | WATERPROOF |
| CXT | WAVEGUIDE PROBE |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAQ8)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information