An item specifically designed to contain a CARTRIDGE, EXPLOSIVE BOLT or an encapsulated explosive charge, or the like. When ignited the explosive furnishes the shock which causes the bolt to separate. May include connectors, bridge wires, or the like.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED60121*)
BTJYDBOLT TYPE
INDICATES THE TYPE OF BOLT PROVIDED.
Enter the applicable reply code from the table below
(BTJYDGAW)
| Table 1 |
| Reply Code (AK54) | Reply |
| GAX | EJECTING |
| GAW | TRACTION |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) ADM WERE ENTERED FOR MRC AHUF, YOU MUST ANSWER MRC (ATFZ)
AHUF*DCARTRIDGE DESIGN TYPE
INDICATES THE DESIGN TYPE CHARACTERISTIC OF THE CARTRIDGE.
Enter the applicable reply code from the table below
(AHUFDADL)
| Table 1 |
| Reply Code (AF43) | Reply |
| ADL | INSTANTANEOUS |
| ADM | TIME DELAY |
ATFZ*BDELAY TIME IN SECONDS
A NUMERIC VALUE INDICATING THE ELAPSED TIME INTERVAL OF THE ITEM,EXPRESSED IN SECONDS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ATFZB2.0)
AHUE*ACARTRIDGE MODEL NUMBER
THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE CARTRIDGE.
Enter the alpha-numeric reply with a minimum of one character.
(AHUEAI1)
AHVNDDETONATION INITIATION METHOD
THE MEANS USED TO INITIATE DETONATION OF THE ITEM.
Enter the applicable reply code from the table below
(AHVNDF)
| Table 1 |
| Reply Code (AF48) | Reply |
| E | AUTOMATIC |
| B | ELECTRIC |
| F | GAS |
| G | MANUAL |
| H | MECHANICAL |
AWCH*JELECTRICAL LEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ELECTRICAL LEAD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWCHJLC2.0*;AWCHJLC2.0$JLC2.0*;AWCHJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APCC*JELECTRICAL RESISTANCE
A MEASUREMENT OF THE OPPOSITION TO THE FLOW OF DIRECT OR ALTERNATING CURRENT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APCCJMB2.0*)
| Table 1 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APHB*JOPERATING CURRENT IN AMPS
THE AMOUNT OF OPERATING CURRENT,EXPRESSED IN AMPERES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APHBJB2.0*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANNY*AQUANTITY WITHIN EACH IMMEDIATE CONTAINER
THE NUMBER OF ITEMS WITHIN EACH IMMEDIATE CONTAINER.
Enter the alpha-numeric reply with a minimum of one character.
(ANNYAL0)
DDACADOD AMMUNITION CODE
A NINE /9/ CHARACTER SEMISIGNIFICANT NUMBER DIVIDED INTO TWO PARTS BY A HYPHEN CENTRALLY ASSIGNED TO GENERIC DESCRIPTIONS APPLICABLE TO ITEMS OF SUPPLY IN FSG 13 AND 14.
Enter the applicable code.
(DDACA1340-H725*)
AMWN*AMODEL NUMBER
THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(AMWNAQ3)
IF STYLE/REPLY CODE(s) AM, NS, RC, RF, RT OR WW WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP)
IF STYLE/REPLY CODE(s) BA, SJ, SK, SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CQQR)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CQQR)
IF STYLE/REPLY CODE(s) TT WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP)
IF STYLE/REPLY CODE(s) DD WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP)
IF STYLE/REPLY CODE(s) LH WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CQQR)
IF STYLE/REPLY CODE(s) NP OR SQ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM)
IF STYLE/REPLY CODE(s) JC, JE, JF, JS, NC, NE, NF, NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP) or (CQQR)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDDD)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| TT | BUTTRESS |
| DD | DARDALET |
| SM | ISO M |
| SS | ISO S |
| LH | LOWENHERZ |
| EM | M |
| MJ | MJ |
| NP | NPT |
| SJ | SI |
| SK | SI-M |
| SQ | SQUARE |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NM | UNM |
| RC | UNRC |
| RF | UNRF |
| RT | UNRS |
| NS | UNS |
| WW | WHITWORTH |
Reference NotesFor reply code NM, disregard the "with options" phrase. The options are to answer either MRCs AHYM and CMLP or MRC CQQR.
AHYM*JNOMINAL THREAD DIAMETER
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAM8)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASAJLB2.0*;AASAJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASB*JFASTENER LENGTH
THE DIMENSION,MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS,FROM THE LARGEST BEARING SURFACE OF THE FASTENER HEAD TO THE EXTREME OPPOSITE END,OR AS SPECIFICALLY DESIGNATED FOR OTHER TYPE FASTENERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASBJAC2.0*;AASBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Fastener length is indicated by Legend L.
AASK*LHEAD STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HEAD.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AASKLC48)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| CF10094 | C1 | HEXAGON |
| CF10103 | C10 | DOUBLE HEXAGON W/ HOLE |
| CF10187 | C100 | KNURLED NO. 5 |
| CF10188 | C101 | HEADLESS (SETSCREW) |
| CF10104 | C11 | SPLINE EXTENDED WASHER |
| CF10200 | C113 | OVAL |
| CF10201 | C114 | COUNTERSUNK CYLINDRICAL CONVEX |
| DQ00266 | C115 | TORX EXTENDED WASHER |
| DQ01038 | C116 | CHAMFER SERRATED FLANGE |
| DQ01039 | C117 | CHAMFER FLANGE |
| CF10105 | C12 | SPLINE DRIVE SHEAR HEAD |
| CF10106 | C13 | SQUARE |
| CF10107 | C14 | SQUARE COUNTERSUNK |
| CF10108 | C15 | SQUARE EXTENDED WASHER |
| CF10109 | C16 | SQUARE WEDGE |
| CF10110 | C17 | TEE NO. 1 |
| CF10111 | C18 | TEE NO. 2 |
| CF10112 | C19 | TEE NO. 3 |
| CF10095 | C2 | UNDERCUT HEXAGON |
| CF10113 | C20 | TEE NO. 4 |
| CF10114 | C21 | TEE NO. 5 |
| CF10115 | C22 | TEE NO. 6 |
| CF10116 | C23 | ROUND W/ WRENCH FLATS |
| CF10117 | C24 | ROUND W/ WRENCH FLATS CHAMFERED |
| CF10118 | C25 | DEE |
| CF10119 | C26 | DEE CHAMFER |
| CF10120 | C27 | DRIVE |
| CF10121 | C28 | BEVEL-CONICAL |
| CF10122 | C29 | BINDING |
| CF10096 | C3 | DISHED HEXAGON |
| CF10123 | C30 | BUTTON |
| CF10124 | C31 | OVAL |
| CF10125 | C32 | PAN |
| CF10126 | C33 | PAN NO. 2 |
| CF10127 | C34 | MODIFIED PAN |
| CF10128 | C35 | UNDERCUT PAN NO. 2 |
| CF10129 | C36 | ROOF |
| CF10130 | C37 | ROUND |
| CF10131 | C38 | ROUND EXTENDED WASHER |
| CF10132 | C39 | ROUND WEDGE |
| CF10097 | C4 | CROWNED HEXAGON |
| CF10133 | C40 | TRUSS |
| CF10134 | C41 | UNDERCUT UNIVERSAL |
| CF10135 | C43 | DOUBLE CHAMFER |
| CF10136 | C44 | FILLISTER |
| CF10137 | C45 | FILLISTER EXTENDED WASHER |
| CF10138 | C46 | FILLISTER COUNTERSUNK |
| CF10139 | C47 | FLUSH |
| CF10140 | C48 | FLAT FILLISTER |
| CF10141 | C49 | FLAT CHAMFER |
| CF10098 | C5 | HEXAGON COUNTERSUNK |
| CF10142 | C50 | FLAT COUNTERSUNK |
| CF10143 | C51 | FLAT COUNTERSUNK UNDERCUT |
| CF10144 | C53 | FLAT TOP ELEVATOR |
| CF10145 | C54 | OVAL COUNTERSUNK |
| CF10146 | C55 | OVAL COUNTERSUNK UNDERCUT |
| CF10147 | C57 | WATERTIGHT |
| CF10148 | C58 | WATERTIGHT |
| CF10149 | C59 | FLAT COUNTERSUNK KEYED |
| CF10099 | C6 | HEXAGON COUNTERSUNK UNDERCUT |
| CF10150 | C61 | FLAT COUNTERSUNK REVERSE KEYED |
| CF10151 | C62 | FLAT COUNTERSUNK REVERSE KEYED NO. 2 |
| CF10152 | C63 | FLAT KEYED |
| CF10153 | C64 | PALM GRIP |
| CF10154 | C65 | STAR KNOB |
| CF10155 | C66 | KNURLED NO. 1 |
| CF10156 | C67 | KNURLED NO. 2 |
| CF10157 | C68 | KNURLED NO. 3 |
| CF10158 | C69 | KNURLED NO. 4 |
| CF10100 | C7 | HEXAGON EXTENDED WASHER |
| CF10159 | C70 | KNURLED NO. 6 |
| CF10160 | C71 | BLIND |
| CF10161 | C72 | BALL |
| CF10162 | C73 | SPADE |
| CF10163 | C76 | SWIVEL HANDLE |
| CF10164 | C77 | THUMB NO. 1 |
| CF10165 | C78 | THUMB NO. 2 |
| CF10166 | C79 | THUMB NO. 3 |
| CF10101 | C8 | DOUBLE HEXAGON |
| CF10167 | C80 | THUMB NO. 4 |
| CF10168 | C81 | THUMB NO. 5 |
| CF10169 | C82 | THUMB NO. 6 |
| CF10170 | C83 | THUMB NO. 7 |
| CF10171 | C84 | THUMB NO. 8 |
| CF10172 | C85 | THUMB NO. 9 |
| CF10173 | C86 | WING NO. 1 |
| CF10174 | C87 | WING NO. 2 |
| CF10175 | C88 | WING NO. 3 |
| CF10176 | C89 | WING NO. 4 |
| CF10102 | C9 | DOUBLE HEXAGON EXTENDED WASHER |
| CF10177 | C90 | DISTORTED HEAD |
| CF10178 | C91 | DOUBLE HEXAGON EXTENDED WASHER |
| CF10179 | C92 | FLAT EXTENDED WASHER |
| CF10180 | C93 | FIXED HANDLE |
| CF10186 | C99 | SLIDING HANDLE |
AASL*JHEAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HEAD,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASLJLB2.0*;AASLJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASM*JBOTTOM COUNTERSINK DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASMJAA2.0*;AASMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASN*JHANDLE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASNJAA2.0*;AASNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASQ*JHANDLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HANDLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASQJLA2.0*;AASQJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASR*JHEAD INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASRJAC2.0*;AASRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAST*JKEY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A KEY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASTJAB2.0*;AASTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASU*JHEAD HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEAD,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASUJAA2.0*;AASUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASV*JHEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASVJAA2.0*;AASVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASW*JKEY PROJECTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASWJAC2.0*;AASWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASX*JTEE BOLT CYLINDRICAL HEAD DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASXJLC2.0*;AASXJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASY*JDISTANCE FROM CENTERLINE TO FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASYJLB2.0*;AASYJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASZ*JTEE HEAD FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASZJLA2.0*;AASZJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATB*JWIDTH BETWEEN FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATBJAA2.0*;AATBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATC*JEXTENDED WASHER DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATCJLC2.0*;AATCJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATD*JEXTENDED WASHER THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATDJAB2.0*;AATDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZG*JHEAD MAJOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZGJLB2.0*;AAZGJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZH*JHEAD MINOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZHJLB2.0*;AAZHJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRSQ*JCOUNTERSINK ANGLE
THE INCLUDED ANGLE OF THE COUNTERSINK.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRSQJRB2.0*;CRSQJRB2.0$$JRB2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSYT*JCHAMFER ANGLE
THE INCLUDED ANGLE OF THE CHAMFER(S).
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYTJDB2.0*;CSYTJDB2.0$$JDB2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDPCCB00*;MATT3AEEDPCCB00$DCUA000*;MATT3AEEDPCCB00$$DCUA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CDA000 | CADMIUM |
| CLD000 | CERAMIC |
| CRA000 | CHROMIUM |
| CTB000 | COBALT ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| GSB000 | GLASS FIBER |
| AUB000 | GOLD ALLOY |
| IRA000 | IRIDIUM |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| FEB000 | IRON CAST |
| PBA000 | LEAD |
| PBB000 | LEAD ALLOY |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| AYA000 | MICA |
| MBA000 | MOLYBDENUM |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCD000 | PLASTIC ACRYLIC |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCF000 | PLASTIC ALLYL |
| PCG000 | PLASTIC DIALLYL PHTHALATE |
| PCH000 | PLASTIC EPOXY |
| PCK000 | PLASTIC METHYL METHACRYLATE |
| PCCB00 | PLASTIC NYLON |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCCW00 | PLASTIC POLYBUTYLENE TEREPHTHALATE |
| PCQ000 | PLASTIC POLYCAPROLACTAM |
| PCR000 | PLASTIC POLYCARBONATE |
| PCT000 | PLASTIC POLYCHLOROTRIFLUOROETHYLENE |
| PCX000 | PLASTIC POLYETHYLENE |
| PCZ000 | PLASTIC POLYHEXAMETHYLENE ADIPAMIDE |
| PCAM00 | PLASTIC POLYHEXAMETHYLENE AMIDE |
| PCAA00 | PLASTIC POLYHEXAMETHYLENE SEBACAMIDE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE (PVC) |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PCBD00 | PLASTIC VINYL CHLORIDE |
| PTA000 | PLATINUM |
| LRL000 | RAWHIDE |
| RC0019 | RUBBER BUTADIENE-ACRYLONITRILE CLASS NBR |
| RC0009 | RUBBER ETHYLENE-PROPYLENE CLASS EPM |
| RC0014 | RUBBER FLUOROSILICONE CLASS FQ |
| RCA000 | RUBBER NATURAL |
| RC0021 | RUBBER SILICONE CLASS Q |
| RCB000 | RUBBER SYNTHETIC |
| AGA000 | SILVER |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
| MTF000 | TANTALUM |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TNC000 | TUNGSTEN ALLOY |
| VNA000 | VANADIUM |
| VNB000 | VANADIUM ALLOY |
| ZNA000 | ZINC ALLOY |
CQBC*JMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CQBCJPTEXT1234*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
CQSX*JSHEAR STRENGTH
THE MINIMUM LOAD,APPLIED PERPENDICULARLY TO THE LONGITUDINAL AXIS OF AN ITEM,AT WHICH POINT THE ITEM WILL FRACTURE WHEN SUBJECTED TO THE STANDARD SHEAR TEST METHOD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit.
(CQSXJBZ2*)
| Table 1 |
| Reply Code (AF09) | Reply |
| B | DOUBLE |
| C | SINGLE |
| Table 2 |
| Reply Code (AN71) | Reply |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAGA000)
| Table 1 |
| Reply Code (MA01) | Reply |
| AGA000 | SILVER |
GRWT*JGROSS WEIGHT
THE COMBINED WEIGHT OF THE ITEM AND ITS LOADED CONTENTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(GRWTJEBAJ2.0*)
| Table 1 |
| Reply Code (AD28) | Reply |
| AR | PALLET |
| EJ | PALLET DOMESTIC, US NAVY |
| EK | PALLET FLEET, US NAVY |
| ED | PALLET, US AIR FORCE |
| EE | PALLET, US ARMY |
| EF | PALLET, US MARINE CORPS |
| EB | SHIPPING CONTAINER |
| Table 2 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
CZKA*JPACKAGE REFERENCE NUMBER
AN ALPHA-NUMERIC CODE IDENTIFYING THE DRAWING AND/OR SPECIFICATION WHICH CONTROLS THE LOADING OF THE PACKAGE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CZKAJADTEXT1234*)
| Table 1 |
| Reply Code (AF94) | Reply |
| AB | US AIR FORCE |
| AC | US ARMY |
| AD | US MARINE CORPS |
| AE | US NAVY |
EXWT*JNET EXPLOSIVE WEIGHT
THE NET WEIGHT OF THE EXPLOSIVE CONTENT OF THE ITEM FOR TRANSPORTATION AND/OR STORAGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(EXWTJBBRAJ2.0*;EXWTJBBRAJ2.0$$JBBRAJ2.1*)
| Table 1 |
| Reply Code (AH21) | Reply |
| BBQ | STORAGE |
| BBR | TRANSPORTATION |
| Table 2 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
HMCC*JHAZARDOUS MATERIAL CLASSIFICATION CODE
AN ALPHA-NUMERIC CODE IDENTIFYING A GROUP OR CLASSIFICATION OF VARIOUS MATERIALS AS TO THEIR POTENTIAL TO CAUSE EXPLOSIONS,FIRES OR DAMAGE BY CHEMICAL ACTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(HMCCJAC2.0*;HMCCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AP66) | Reply |
| AB | COAST GUARD CLASS |
| AC | DEPARTMENT OF DEFENSE HAZARD CLASS DIVISION |
| AD | DEPARTMENT OF TRANSPORTATION CLASS |
| AE | DEPARTMENT OF TRANSPORTATION EXEMPTION |
| AF | FIREFIGHTING GROUP |
| AG | HAZARD SYMBOL |
| AH | INHABITED BUILDING DISTANCE |
| AJ | LOADING-STOWAGE |
| AK | STORAGE COMPATIBILITY GROUP |
SHPN*ADOT PROPER SHIPPING NAME
THE PROPER SHIPPING NAME AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE.
Enter the alpha-numeric reply with a minimum of one character.
(SHPNAA6)
DENN*ADOT IDENTIFICATION NUMBER
THE IDENTIFICATION NUMBER ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PROPER SHIPPING NAME. IDENTIFICATION NUMBERS PRECEDED BY THE LETTERS "UN" ARE ASSOCIATED WITH INTERNATIONAL AS WELL AS DOMESTIC TRANSPORTATION AND THOSE PRECEDED BY THE LETTERS "NA" ARE NOT RECOGNIZED FOR INTERNATIONAL TRANSPORTATION OF HAZARDOUS MATERIALS (DANGEROUS GOODS) EXCEPT TO AND FROM THE UNITED STATES AND CANADA.
Enter the alpha-numeric reply with a minimum of one character.
(DENNAK4)
HAZD*ADOT HAZARD CLASS/DIVISION
A DESIGNATION OF THE HAZARD CLASS OR DIVISION CORRESPONDING TO EACH PROPER SHIPPING NAME FOR HAZARDOUS MATERIAL AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE.
Enter the alpha-numeric reply with a minimum of one character.
(HAZDAG5)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
DTRC*ADOT REGISTRATION CODE
AN ALPHA-NUMERIC CODE ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION IDENTIFYING THE FINAL HAZARD CLASSIFICATION.
Enter the alpha-numeric reply with a minimum of one character.
(DTRCAO1)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
NAAC*AAMMUNITION CODE
A SIGNIFICANT CODE CONSISTING OF A COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS ASSIGNED TO ITEMS OF SUPPLY IN FSG 13 AND 14. IDENTICAL CODES SIGNIFY FUNCTIONALLY INTERCHANGEABLE ITEMS FOR ISSUE AND USE.
Enter the alpha-numeric reply with a minimum of one character.
(NAACAA8)
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
CTJT*JPACKAGE NOMINAL OVERALL LENGTH AND TYPE
THE NOMINAL DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS,AND THE TYPE OF PACKAGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTJTJLED2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AD28) | Reply |
| ED | PALLET, US AIR FORCE |
| EE | PALLET, US ARMY |
| EF | PALLET, US MARINE CORPS |
| EG | PALLET, US NAVY |
| EB | SHIPPING CONTAINER |
CTKG*JPACKAGE NOMINAL OVERALL WIDTH AND TYPE
THE NOMINAL OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE PACKAGE,IN DISTINCTION FROM THICKNESS,AND THE TYPE OF PACKAGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTKGJLEE2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AD28) | Reply |
| ED | PALLET, US AIR FORCE |
| EE | PALLET, US ARMY |
| EF | PALLET, US MARINE CORPS |
| EG | PALLET, US NAVY |
| EB | SHIPPING CONTAINER |
CTHR*JPACKAGE NOMINAL OVERALL HEIGHT AND TYPE
THE NOMINAL DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP,AND THE TYPE OF PACKAGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTHRJLEF2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AD28) | Reply |
| ED | PALLET, US AIR FORCE |
| EE | PALLET, US ARMY |
| EF | PALLET, US MARINE CORPS |
| EG | PALLET, US NAVY |
| EB | SHIPPING CONTAINER |
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAB4)
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAE)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AC | EXPLOSIVE |
| AD | FLAMMABLE |
| AE | FRAGILE |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)