An item consisting of primary cell(s), electrically connected to produce an electromotive force by electrochemical action. The item is a nonrechargeable battery that is completely inert until it is activated by a heating process which melts the electrolyte.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED60096*)
AEXT*DBATTERY ELECTROLYTE
THE COMPOSITION OF THE ELECTROLYTE USED IN THE BATTERY.
Enter the applicable reply code from the table below
(AEXTDF*;AEXTDU$DR*)
| Table 1 |
| Reply Code (AD52) | Reply |
| B | ACID |
| C | ALKALINE |
| Q | AMMONIUM CHLORIDE |
| A | ANY ACCEPTABLE |
| V | CARBON ZINC |
| R | CUPROUS CHLORIDE |
| E | LEAD ACID |
| N | LITHIUM |
| S | MAGNESIUM BROMIDE |
| T | MAGNESIUM PERCHLORATE |
| F | POTASSIUM HYDRATE |
| G | POTASSIUM HYDROXIDE |
| P | SALINE |
| H | SILICA-GEL |
| U | SILVER CHLORIDE |
AFKS*DCOMMERCIAL BATTERY SIZE DESIGNATION
THE COMMERCIAL DESIGNATION OF THE BATTERY SIZE.
Enter the applicable reply code from the table below
(AFKSDP)
ELECBVOLTAGE IN VOLTS
THE TOTAL ELECTRICAL VOLTAGE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ELECB2.0*;ELECB2.0$BM2.0;ELECB2.0$$BM2.0*)
AQGJ*BTAP VOLTAGE IN VOLTS
THE TOTAL ELECTRICAL VOLTAGE OF THE TAP/S/ ON THE ITEM,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AQGJB2.0*;AQGJB2.0$BM2.0;AQGJB2.0$$BM2.0*)
IF YOU ANSWER MRC AQGK, YOU MUST ANSWER MRC (AQGL)
AQGK*BAMPERE HOUR CAPACITY
THE AMOUNT OF ELECTRICAL ENERGY THE ITEM IS RATED TO DELIVER.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AQGKB2.0*;AQGKB2.0$BM2.0;AQGKB2.0$$BM2.0*)
AQGL*BTIME CAPACITY IN HOURS
THE SPECIFIED TIME AT WHICH THE CAPACITY OF THE ITEM IS RATED,EXPRESSED IN HOURS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AQGLB2.0*;AQGLB2.0$BM2.0;AQGLB2.0$$BM2.0*)
SHPEDSHAPE
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(SHPEDAN*;SHPEDFX$DBM*)
| Table 1 |
| Reply Code (AD07) | Reply |
| Z | ANY ACCEPTABLE |
| AN | CYLINDRICAL |
| BM | OBLONG |
| CT | OCTAGONAL |
| RT | RECTANGULAR |
| FX | RECTANGULAR W/CORNER OPTIONAL |
| FY | RECTANGULAR W/DIAGONAL CORNERS |
| FZ | RECTANGULAR W/ROUNDED CORNERS |
| GA | RECTANGULAR W/SLOPING SIDE |
AQGPJAPPROXIMATE SHELF LIFE
THE APPROXIMATE SHELF LIFE /STORAGE TIME/ OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AQGPJHR2.0*)
| Table 1 |
| Reply Code (AH68) | Reply |
| HR | HOURS |
| MN | MINUTES |
| MH | MONTHS |
| YR | YEARS |
AARAATERMINAL QUANTITY
THE NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARAA10*)
IF STYLE/REPLY CODE(s) BX WERE ENTERED FOR MRC AARB, YOU MUST ANSWER MRC (AFRA and AARD)
IF STYLE/REPLY CODE(s) KG WERE ENTERED FOR MRC AARB, YOU MUST ANSWER MRC (AFKA)
AARB*DTERMINAL TYPE
INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. PLEASE USE MRC CSCF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AARBDGT*;AARBDAA$DKM*;AARBDAA$$DKM*)
| Table 1 |
| Reply Code (AA58) | Reply |
| A | ANY ACCEPTABLE |
| BH | BANANA JACK |
| JS | BAYONET |
| AA | BINDING POST |
| KC | BOLT |
| JT | BUTTON |
| KD | CABLE |
| KE | CABLE W/CONNECTOR PLUG |
| KF | CABLE W/CONNECTOR RECEPTACLE |
| BM | CLIP |
| NQ | COIL SPRING |
| KG | CONNECTOR W/LEADS |
| KK | CONNECTOR, FEMALE |
| BP | CONNECTOR, PLUG |
| KH | CONTACT |
| KJ | CRIMPED LUGS ON WIRES |
| NR | ELECON CONNECTOR |
| KL | FLAT CONTACT |
| KM | FLAT SPRING |
| KN | FLAT SURFACE |
| KP | FLUSH DISK |
| CR | INSULATED WIRE LEAD |
| KQ | INTERNAL THREADED POST |
| KR | INTER-TRAY CONNECTOR |
| KS | LAMP BASE |
| FQ | LUG |
| KT | LUG BOLT |
| KW | NUT-BOLT |
| AM | PIN |
| GT | PLUG-IN |
| GW | POST |
| KX | POST W/BOLT |
| KY | QUICK DISCONNECT W/LEADS |
| KZ | RECTANGULAR POST |
| BE | SCREW |
| LA | SNAP-ON |
| BX | SOCKET |
| HN | SOLDER TAB |
| HR | SPRING CLIP |
| LB | SQUARE POST |
| LC | STRAIGHT POST |
| LG | STRAP |
| FX | STUD |
| LD | STUD W/NUT |
| LF | TAPER POST |
| LH | TAPER POST W/WING NUT |
| LE | TAP-SCREW |
| CH | THREADED HOLE |
| LJ | THREADED POST |
| AZ | THREADED STUD |
| LL | THREADED STUD W/NUT |
| LK | TUBE PIN |
| LM | UNTHREADED SOCKET |
| LP | WING NUT |
| BB | WIRE LEAD |
| LQ | WIRE LEAD W/MALE-FEMALE SLEEVE CONNECTOR |
| LN | WIRE LEAD W/SOCKET |
| PB | WIRE LEAD, FLEXIBLE |
AFRA*ACONTACT QUANTITY
THE NUMBER OF CONTACTS WHICH PROVIDE ELECTRICAL CONNECTION.
Enter the numeric reply with a minimum of one digit.
(AFRAA10*)
AARD*ADUMMY TERMINAL QUANTITY
THE NUMBER OF TERMINALS THAT DO NOT PROVIDE ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARDA10*)
AFKA*JWIRING PROVISION LENGTH
THE MEASUREMENT OF EACH WIRING PROVISION OF AN ITEM TAKEN FROM THE BODY TO THE ENDS OF THE WIRING PROVISION,INCLUDING ANY TERMINATIONS.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFKAJLBC2.0*;AFKAJLBC2.0$JLBC2.0*;AFKAJLBC2.0$$JLBC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AE17) | Reply |
| C | NEGATIVE LEAD |
| F | NONSPECIFIED LEAD |
| B | POSITIVE LEAD |
APXH*DTERMINAL LOCATION
THE POSITION OF THE TERMINAL/S/ FOR MAKING CONNECTION TO AN ITEM.PLEASE USE MRC CQTM IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(APXHDADG*;APXHDABA$DABB*;APXHDABA$$DABB*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABA | BOTTOM |
| ABB | END |
| ACZ | SIDE |
| ABD | TOP |
| ADG | TOP AT EACH END |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAB2.0*;ABFYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJAB2.0*;ADUMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKWA*GJOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM NAME
THE NAME ASSIGNED TO THE ITEM BY THE JOINT ELECTRONICS TYPE DESIGNATION SYSTEM.USE MRC AKSJ AND RELATIONSHIP TO MRC AMSB
Enter clear text.
(AKWAGCLEARTEXT)
AKWB*GJOINT ELECTRONICS TYPE DESIGNATION SYSTEM ITEM TYPE NUMBER
THE TYPE NUMBER ASSIGNED TO THE ITEM BY THE JOINT ELECTRONICS TYPE DESIGNATION SYSTEM. USE MRC AMSB
Enter clear text.
(AKWBGCLEARTEXT)
DDAC*ADOD AMMUNITION CODE
A NINE /9/ CHARACTER SEMISIGNIFICANT NUMBER DIVIDED INTO TWO PARTS BY A HYPHEN CENTRALLY ASSIGNED TO GENERIC DESCRIPTIONS APPLICABLE TO ITEMS OF SUPPLY IN FSG 13 AND 14.
Enter the applicable code.
(DDACA1340-H725*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAGA000*;PRMTDPTA000$$DRTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPTA000E2.0*;PMWTJPTA000E2.0$$JPTA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDBE*;BBRGDAL$DAD*;BBRGDAL$$DAD*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AL | TEMPERATURE CONTROLLED WAREHOUSE |
| AJ | UNHEATED WAREHOUSE |
| BE | VENTILATED WAREHOUSE |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information