A rigid item of various shapes permanently attached to a structure of an aircraft, designed to provide access for inspection, service, replacement of components and/or adjustments.It is designed to be attached by means of hinges or similar device.It may include self-closing features and have a quick release or other type latching to permit access with a minimum of effort.It may include an observation window. Excludes:COVER, ACCESS; COVER ACCESS, AIRCRAFT; DOOR, ACCESS; DOOR, AIRCRAFT and all doors not specficially designed to provide access for the purposes listed above.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED51576*)
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC ABMW, YOU MUST ANSWER MRC (ABRY and ABGL)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ABMW, YOU MUST ANSWER MRC (ABRY and ABGL and ADPD and ADPC)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC ABMW, YOU MUST ANSWER MRC (ABRY and ADNV and ADPD and ABGL and ADNY and ADPC)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC ABMW, YOU MUST ANSWER MRC (ABRY and ADPD and ADPB and ABGL and ADPA and ADPC)
IF STYLE/REPLY CODE(s) 13 WERE ENTERED FOR MRC ABMW, YOU MUST ANSWER MRC (ABRY and ADNY and ADPC and ADPD and ADNZ and ABGL)
ABMWLPERIPHERAL SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE PERIPHERAL SHAPE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABMWL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AV10001 | 1 | RECTANGLE, NO HOLES |
| AV10010 | 10 | RECTANGLE, TWO HOLES |
| AV10103 | 103 | TRIANGLE, ROUNDED CORNERS, THREE HOLES |
| AV10107 | 107 | OVAL, FOUR HOLES |
| AV10112 | 112 | PENTAGON, MULTI HOLES |
| AV10115 | 115 | IRREGULAR PENTAGON, NO HOLES |
| AV10117 | 117 | IRREGULAR PENTAGON, THREE HOLES |
| AV10119 | 119 | IRREGULAR PENTAGON, FIVE HOLES |
| AV10122 | 122 | OVAL, MULTI HOLES |
| AV10123 | 123 | RECTANGLE, ROUNDED CORNERS, MULTI HOLES |
| AV10124 | 124 | ROUND, MULTI HOLES |
| AV10126 | 125 | DIAMOND, ROUNDED CORNERS, NO HOLES |
| AV10127 | 126 | BAND TYPE |
| DQ01120 | 129 | TRAPEZOID, MULTI HOLE |
| AV10013 | 13 | RECTANGLE, FOUR HOLES |
| AV10016 | 16 | RECTANGLE, MULTI HOLES |
| AV10019 | 19 | RECTANGLE, MULTI HOLES |
| AV10022 | 22 | RECTANGLE, MULTI HOLES |
| AV10028 | 28 | RECTANGLE, MULTI HOLES |
| AV10031 | 31 | RECTANGLE, MULTI HOLES |
| AV10034 | 34 | RECTANGLE, MULTI HOLES |
| AV10037 | 37 | RECTANGLE, EIGHT HOLES |
| AV10004 | 4 | RECTANGLE, ONE CENTER HOLE |
| AV10040 | 40 | RECTANGLE, MULTI HOLES |
| AV10043 | 43 | RECTANGLE, MULTI HOLES |
| AV10046 | 46 | RECTANGLE, MULTI HOLES |
| AV10068 | 68 | IRRECGULAR, THREE HOLES |
| AV10007 | 7 | RECTANGLE, MULTI HOLES |
| AV10077 | 77 | ROUND, NO HOLES |
| AV10078 | 78 | ROUND, ONE HOLE |
| AV10079 | 79 | ROUND, MULTI HOLES |
| AV10080 | 80 | ROUND, MULTI HOLES |
| AV10082 | 82 | OVAL, NO HOLES |
| AV10083 | 83 | OVAL, ONE HOLE |
| AV10084 | 84 | OVAL, MULTI HOLES |
| AV10090 | 90 | ROUND, TWO EARS AND HOLES |
| AV10095 | 95 | TRIANGLE, SHARP CORNERS, NO HOLES |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAC2.0*;ABGLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAC2.0*;ABKGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAB2.0*;ABKVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAC2.0*;ABRYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNX*JBODY RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNXJAB2.0*;ADNXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPA*JDISTANCE BETWEEN HOLE CENTERLINE AND FIRST HOLE ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPAJAA2.0*;ADPAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPB*JDISTANCE BETWEEN HOLE CENTERLINE AND FIRST HOLE ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPBJAA2.0*;ADPBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPC*JDISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPCJAA2.0*;ADPCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPD*JDISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPDJAA2.0*;ADPDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPF*JINVERTED RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPFJAC2.0*;ADPFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPG*JEAR RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPGJAC2.0*;ADPGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVJ*JBOLT HOLE CENTERLINE TO NEAREST EDGE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVJJAB2.0*;ADVJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPK*JCORNER HOLE CENTERLINE RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPKJAC2.0*;ADPKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BPCJ*JDISTANCE BETWEEN HOLE CENTERS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BPCJJAB2.0*;BPCJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BPYD*JMINOR LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BPYDJAB2.0*;BPYDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNY*JDISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNYJAA2.0*;ADNYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNZ*JDISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNZJAC2.0*;ADNZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNV*AHOLE QUANTITY ALONG LENGTH
NONE.
Enter the numeric reply with a minimum of one digit.
(ADNVA10*)
ADNW*AHOLE QUANTITY ALONG WIDTH
NONE.
Enter the numeric reply with a minimum of one digit.
(ADNWA10*)
ADPJ*ACORNER QUANTITY
NONE.
Enter the numeric reply with a minimum of one digit.
(ADPJA10*)
ADPM*ABOLT CIRCLE HOLE QUANTITY
THE NUMBER OF HOLES IN A BOLT CIRCLE.
Enter the numeric reply with a minimum of one digit.
(ADPMA10*)
CKWB*DCORNER CUT TYPE
INDICATES THE TYPE OF CUT ON THE CORNER/S/.
Enter the applicable reply code from the table below
(CKWBDER*;CKWBDEQ$DAA*)
| Table 1 |
| Reply Code (AL18) | Reply |
| AA | BEVEL |
| EQ | ROUND |
| ER | SQUARE |
ADNU*JCORNER RADIUS
A MEASUREMENT OF A STRAIGHT LINE FROM THE MIDPOINT OF A ROUNDED CORNER TO ITS PERIPHERY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNUJAC2.0*;ADNUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPE*JCORNER BEVEL LENGTH
THE LENGTH OF A LINEAR BREAK AT AN ANGLE TO THE SURFACES FORMING THE EDGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPEJAC2.0*;ADPEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1, 2 OR 3 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPR and ADPQ and ADPN and AARX and ABKU)
IF STYLE/REPLY CODE(s) 4, 5 OR 6 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPN and ADPQ and ADPR and ADJT and ABKU and ADJU)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABKU and ADPN and ADPR)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPX and ADPW and CWCJ and ADPR and ADPQ and AARX and ADPN and ABKU)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPQ and AARX and ABKU and ADPN)
IF STYLE/REPLY CODE(s) 16 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (CWCJ and AARX and ABKU and ADPN)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABKU)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPQ and ADPR and ADJT and ADJU and ADPN and ABKU)
IF STYLE/REPLY CODE(s) 26 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPR)
IF STYLE/REPLY CODE(s) 27 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPR)
IF STYLE/REPLY CODE(s) 28 OR 29 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPR and ABKU)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADPQ and ADPR)
IF STYLE/REPLY CODE(s) 31 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ADJU and ADJT and ADPN and ABKU)
IF STYLE/REPLY CODE(s) 32 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (AARX and ADPR)
AAGRLCROSS-SECTIONAL SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAGRL29)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AV10130 | 1 | SPHERICAL RECESS |
| AV10139 | 10 | CIRCULAR RECESS |
| AV10140 | 11 | CIRCULAR RECESS |
| AV10145 | 16 | CIRCULAR RECESS |
| AV10146 | 17 | LOUVERED OPENING |
| AV10165 | 19 | SQUARE OR RECTANGULAR RECESS |
| AV10131 | 2 | CIRCULAR RECESS |
| AV10147 | 26 | FLAT |
| AV10148 | 27 | FLAT W/OPEN CENTER |
| AV10149 | 28 | FLAT, ROUND RIB REINFORCED |
| AV10150 | 29 | FLAT, SQUARE OR RECTANGULAR RIB REINFORCED |
| AV10132 | 3 | CIRCULAR RECESS |
| AV10151 | 30 | ARCHED |
| AV10152 | 31 | RECESS, OTHER THAN ROUND |
| AV10153 | 32 | CYLINDER W/O LINER |
| AV10133 | 4 | OBLONG RECESS |
| AV10134 | 5 | OBLONG RECESS |
| AV10135 | 6 | SQUARE OR RECTANGULAR RECESS |
| AV10138 | 9 | RECESS, SAME SHAPE AS THE PERIPHERY |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAB2.0*;AARXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKU*JFLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKUJAA2.0*;ABKUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJT*JINSIDE WIDTH
AN INSIDE MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJTJAA2.0*;ADJTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADJU*JINSIDE LENGTH
A MEASUREMENT OF THE LONGEST INSIDE DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADJUJAA2.0*;ADJUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPN*JFIRST RECESS INSIDE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPNJAC2.0*;ADPNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPQ*JINSIDE CORNER RADIUS
A MEASUREMENT OF THE LINE SEGMENT EXTENDING FROM THE CENTER OF A CIRCLE OR SPHERE TO THE CURVE OF AN INSIDE CORNER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPQJAB2.0*;ADPQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPR*JBODY THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A BODY,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPRJAA2.0*;ADPRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPW*JOUTSIDE CORNER RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPWJAA2.0*;ADPWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPX*JBODY OUTSIDE RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPXJAA2.0*;ADPXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWCJ*JINSIDE ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWCJJRB2.0*;CWCJJRB2.0$$JRB2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDPCH000*;MATTDGFA000$DPCP000*;MATTDGFA000$$DPCP000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL2219 | ALUMINUM ALLOY 2219 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7075 | ALUMINUM ALLOY 7075 |
| AL7076 | ALUMINUM ALLOY 7076 |
| AL7178 | ALUMINUM ALLOY 7178 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| GSB000 | GLASS FIBER |
| GFA000 | GRAPHITE |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| MG0001 | MAGNESIUM ALLOY AZ31B |
| MG0007 | MAGNESIUM ALLOY AZ63A |
| MG0008 | MAGNESIUM ALLOY AZ91C |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCCX00 | PLASTIC ARAMID |
| PCH000 | PLASTIC EPOXY |
| PCP000 | PLASTIC POLYAMIDE |
| PCR000 | PLASTIC POLYCARBONATE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE |
| WDB000 | PLYWOOD |
| FBC000 | POLYESTER |
| RCE000 | RUBBER |
| RCC000 | RUBBER SILICONE |
| RCB000 | RUBBER SYNTHETIC |
| STA000 | STEEL |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0321 | STEEL COMP 321 |
| ST0347 | STEEL COMP 347 |
| STB000 | STEEL CORROSION RESISTING |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TT0052 | TITANIUM ALLOY UNS R56400 |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| B | FED SPEC |
| C | FED STD |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| B | 1ST MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDXXA000*;SFTTDPNA000$DPSA000*;SFTTDPNA000$$DPSA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| MSL000 | ALODIZE |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PNC000 | PAINT ALUMINUM |
| PND000 | PAINT EPOXY |
| PSA000 | PASSIVATE |
| PRA000 | PRIMER |
| PRD000 | PRIMER EPOXY-POLYAMIDE |
| PRC000 | PRIMER ZINC CHROMATE |
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| B | FED SPEC |
| C | FED STD |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ADQBDSECURING DEVICE TYPE
INDICATES THE TYPE OF DEVICE USED TO FASTEN THE ITEM.
Enter the applicable reply code from the table below
(ADQBDAA*;ADQBDAG$DAB*;ADQBDAG$$DAB*)
| Table 1 |
| Reply Code (AC52) | Reply |
| AA | ELBOW CATCH |
| AB | FLUSH CATCH |
| AC | FRICTION CATCH |
| AD | HINGE |
| AE | PAWL |
| AF | SLIDE FASTENER |
| JF | SPECIAL |
| AG | SPRING CLIP |
| AH | STRAP CLAMP |
| AJ | THREADED FASTENER |
| AK | TURNLOCK FASTENER |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC ADQK, YOU MUST ANSWER MRC (AAUB)
ADQK*LMOUNTING OPENING SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE MOUNTING OPENING.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ADQKL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AV10157 | 1 | UNTHREADED HOLE |
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJAA2.0*;AAUBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAQA*;CBBLDBRP$$DAPZ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BRN | HANDLE FOR OPENING, LIFTING, CLOSING, OR THE LIKE |
| APY | MAGNETIC SELF-CLOSING |
| APZ | OBSERVATION FACILITY |
| BRQ | SEALING CAPABILITY |
| BRP | SPECIAL MARKING |
| AQA | SPRING LOADED SELF-CLOSING |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information