A metallic item of circular-shaped design with open center area to permit positioning over a shock strut cylinder or piston.It must have one or more mounting bosses to provide for attachment of torque arm(s), connecting link(s), or the like for desired directional control of the aircraft wheels.Thisdevice is utilized for both nose and main landing gear applications.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED49874*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDSTA000*;MATTDALB000$DAL2024*;MATTDALB000$$DAL2024*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| AL2024 | ALUMINUM ALLOY 2024 |
| STA000 | STEEL |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDCDA000*;SFTTDCDA000$DCDA000*;SFTTDCDA000$$DCDA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| CDA000 | CADMIUM |
IF STYLE/REPLY CODE(s) A1 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABNM)
IF STYLE/REPLY CODE(s) A2 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and AEUZ and AATE and ABNM)
IF STYLE/REPLY CODE(s) A3 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABNM and ABGG)
IF STYLE/REPLY CODE(s) A4 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ABXV and AATE and AEUZ and ABNM)
IF STYLE/REPLY CODE(s) A5 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABNM)
IF STYLE/REPLY CODE(s) A6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABNM)
IF STYLE/REPLY CODE(s) A7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and AEUY and ABNM)
IF STYLE/REPLY CODE(s) A8 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABPH and AEUZ and ABNM)
IF STYLE/REPLY CODE(s) A9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABPH and ABKV and AEUY and AEUZ and ABNM)
IF STYLE/REPLY CODE(s) A10 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and AEUZ and ABPH and ABNM)
IF STYLE/REPLY CODE(s) A11 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and AEUZ and ABPH and ABNM)
IF STYLE/REPLY CODE(s) A12 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABNM)
IF STYLE/REPLY CODE(s) A13 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and ABKV and ABNM)
IF STYLE/REPLY CODE(s) A14 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABXV and AEUY and ABHP and ABMK and ABNM)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLA10)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAJ1204 | A1 | PLAIN ROUND |
| AAJ1213 | A10 | ROUND STEPPED |
| AAJ1214 | A11 | ROUND STEPPED |
| AAJ1215 | A12 | ROUND SECTIONAL |
| AAJ1216 | A13 | ROUND SECTIONAL |
| AAJ1217 | A14 | PLAIN RECTANGULAR |
| AAJ1205 | A2 | ROUND W/SINGLE CHAMFER |
| AAJ1206 | A3 | ROUND W/ SINGLE EDGE |
| AAJ1207 | A4 | ROUND W/DOUBLE CHAMFER |
| AAJ1208 | A5 | ROUND W/GROOVED PERIPHERY |
| AAJ1209 | A6 | ROUND W/GROOVED PERIPHERY |
| AAJ1210 | A7 | ROUND W/SINGLE LOBE |
| AAJ1211 | A8 | ROUND STEPPED |
| AAJ1212 | A9 | ROUND STEPPED |
AATE*BCHAMFER ANGLE IN DEG
THE MEASUREMENT OF THE CHAMFER ANGLE,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AATEB2.0)
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAB2.0*;ABKVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJAC2.0*;ABNMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPH*JSMALL END DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALL END,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPHJAA2.0*;ABPHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXV*JBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXVJAB2.0*;ABXVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEUY*JDISTANCE FROM BORE CENTERLINE TO END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEUYJAC2.0*;AEUYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEUZ*JLARGEST DIAMETER LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEUZJAC2.0*;AEUZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGG*JRADIUS
THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGGJAC2.0*;ABGGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHYK*JCENTER TO CENTER DISTANCE BETWEEN SHAFT HOLE AND BORE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYKJAC2.0*;AHYKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF YOU ANSWER MRC AHYF, YOU MUST ANSWER MRC (CQKB)
AHYF*ASECURING HOLE QUANTITY
THE NUMBER OF HOLES PROVIDED FOR SECURING THE ITEM IN A FIXED POSITION.
Enter the numeric reply with a minimum of one digit.
(AHYFA10*)
AHYG*BANGLE BETWEEN CENTERLINES OF SECURING HOLES IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE HOLE INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AHYGB2.0*;AHYGB2.0$$BM2.0*)
CQKB*HSECURING HOLE TYPE AND LOCATION
INDICATES THE TYPE OF SECURING HOLE AND THE LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CQKBHHAFC2.0*;CQKBHHAFC2.0$$HHAFC2.1*)
| Table 1 |
| Reply Code (AB68) | Reply |
| F | TAPER PIN PILOT |
| D | THREADED |
| G | THREADED-COUNTERBORED |
| H | THREADED-COUNTERSUNK |
| E | UNTHREADED |
| J | UNTHREADED-COUNTERSUNK |
| Table 2 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
CRZW*JHOLE DIAMETER AND LOCATION
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE,AND THE LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRZWJABAFA2.0*;CRZWJABAFA2.0$$JABAFA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
CRLR*JCOUNTERBORE DIAMETER AND LOCATION
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE,AND THE LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRLRJAAAFE2.0*;CRLRJAAAFE2.0$$JAAAFE2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
CQZD*JCOUNTERBORE DEPTH AND LOCATION
A MEASUREMENT BETWEEN SPECIFIED POINTS OF A COUNTERBORE AND THE LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQZDJABAHL2.0*;CQZDJABAHL2.0$$JABAHL2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
CSFB*JCOUNTERSINK MAJOR DIAMETER AND LOCATION
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST DIMENSION OF A COUNTERSINK,AND TERMINATES AT THE INNER CIRCUMFERENCE,AND THE LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSFBJAASNH2.0*;CSFBJAASNH2.0$$JAASNH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
IF STYLE/REPLY CODE(s) UN WERE ENTERED FOR MRC CQBP, YOU MUST ANSWER MRC (CQTP)
CQBP*HSCREW THREAD SERIES DESIGNATOR AND LOCATION
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER,AND THE THREAD LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CQBPHAHLNF*)
| Table 1 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
| Table 2 |
| Reply Code (AH06) | Reply |
| NP | NPT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
CQTP*JSCREW THREAD QUANTITY PER INCH AND LOCATION
THE NUMBER OF SCREW THREADS ON THE ITEM PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS AND THE THREAD LOCATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQTPJSNH2*)
| Table 1 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
ACYD*JTHREAD PITCH IN MILLIMETERS AND LOCATION
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS, EXPRESSED IN MILLIMETERS, AND THE THREAD LOCATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYDJAFA2.0*)
| Table 1 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
CQNY*JCOUNTERSUNK HOLE ANGLE IN DEG AND LOCATION
THE COUNTERSUNK HOLE ANGLE,EXPRESSED IN DEGREES,AND THE LOCATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQNYJAFG2.0*)
| Table 1 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
CSMJ*HTAPERED PIN SIZE ACCOMMODATED AND LOCATION
DESIGNATES THE SIZE OF THE TAPERED PIN THAT THE ITEM IS DESIGNED TO ACCOMMODATE AND THE LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CSMJHAKAFH*)
| Table 1 |
| Reply Code (AP16) | Reply |
| AK | 0 |
| AL | 1 |
| AX | 10 |
| AY | 11 |
| AZ | 12 |
| BA | 13 |
| BB | 14 |
| AM | 2 |
| AJ | 2/0 |
| AN | 3 |
| AH | 3/0 |
| AP | 4 |
| AG | 4/0 |
| AQ | 5 |
| AF | 5/0 |
| AR | 6 |
| AE | 6/0 |
| AS | 7 |
| AD | 7/0 |
| AT | 8 |
| AC | 8/0 |
| AW | 9 |
| AB | 9/0 |
| Table 2 |
| Reply Code (AN73) | Reply |
| AFA | 1ST HOLE |
| AFB | 2ND HOLE |
| AFC | 3RD HOLE |
| AFD | 4TH HOLE |
| AFE | 5TH HOLE |
| AFF | 6TH HOLE |
| AFG | 7TH HOLE |
| AFH | 8TH HOLE |
| AHL | ALL HOLES |
| SNH | SINGLE HOLE |
IF YOU ANSWER MRC AEVC, YOU MUST ANSWER MRC (ABLJ and AEVD)
AEVC*AKEY QUANTITY
THE NUMBER OF KEYS CONTAINED IN OR ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEVCA10*)
AEVG*BKEY SPACING IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEVGB2.0)
ABLJ*JINTERNAL STRAIGHT KEY WIDTH
THE MEASUREMENT FROM ONE FLAT SURFACE OF THE KEY TO THE OPPOSITE FLAT SURFACE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABLJJAB2.0*;ABLJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEVD*JDISTANCE FROM CENTER OF BORE TO TOP OF KEY
THE DISTANCE FROM THE CENTER OF THE BORE TO THE TOP OF THE KEY/S/.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVDJAC2.0*;AEVDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF YOU ANSWER MRC AEVE, YOU MUST ANSWER MRC (ABLM and AEVF)
AEVE*AKEYWAY QUANTITY
THE NUMBER OF KEYWAYS CONTAINED IN OR ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEVEA10*)
AEVJ*BKEYWAY SPACING IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEYWAY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEVJB2.0)
ABLM*JINTERNAL KEYWAY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN INTERNAL KEYWAY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABLMJAA2.0*;ABLMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEVF*JDISTANCE FROM CENTER OF BORE TO BOTTOM OF KEYWAY
THE DISTANCE FROM THE CENTER OF THE BORE TO THE BOTTOM OF THE KEYWAY(S).
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVFJAC2.0*;AEVFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) JG WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (BDPK)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDJG)
| Table 1 |
| Reply Code (EN02) | Reply |
| JG | ASBESTOS ALTERNATIVE PRODUCTS |
BDPK*JASBESTOS CONTENT PERCENTAGE
THE ASBESTOS CONTENT OF THE ITEM,EXPRESSED IN PERCENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDPKJA2.0*;BDPKJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
PKWT*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PKWTJLB2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAR*;BBRGDAX$DAG*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AB | ABOVE GROUND MAGAZINE |
| AT | DOCK LEVEL HEATED WAREHOUSE |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AS | GROUND LEVEL HEATED WAREHOUSE |
| AW | GROUND LEVEL UNHEATED WAREHOUSE |
| AF | IGLOO MAGAZINE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AK | UNIMPROVED OPEN |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
TMQY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TMQYJAFY2*;TMQYJAFY2$$JAFY3*)
| Table 1 |
| Reply Code (AB28) | Reply |
| ABR | BOLT |
| ACA | FLAT WASHER |
| AFX | HEADLESS STRAIGHT PIN |
| ACB | LOCK WASHER |
| AGA | MACHINE SCREW |
| ABW | NUT |
| AFJ | SETSCREW |
| AFZ | SOCKET HEAD CAP SCREW |
| AFW | SPRING PIN |
| AFY | TAPERED PIN |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDRTA000$DAZA000*;PRMTDRTA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAGA000F2.0*;PMWTJAGA000F2.0$$JAGA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PKQT*AINTERMEDIATE PACKAGE QUANTITY
THE NUMBER OF WRAPS,BOXES,OR BUNDLES,WHICH CONTAINS TWO OR MORE UNITS OF ISSUE,PLACED INSIDE AN EXTERIOR CONTAINER.
Enter the numeric reply with a minimum of one digit.
(PKQTA10*)
EXQT*AEXTERIOR CONTAINER QUANTITY
THE NUMBER OF UNITS OF ISSUE PLACED INSIDE THE EXTERIOR CONTAINER. PLEASE USE MRC NMBR WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the numeric reply with a minimum of one digit.
(EXQTA10*)
SUWT*JUNIT OF ISSUE WEIGHT
THE MEASURED WEIGHT OF THE ACTUAL CONTAINER(S) OR SUPPORTING DEVICE(S) WHICH IS IN DIRECT CONTACT WITH THE ITEM AND ITS CONTENTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUWTJLB2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
ECWT*JEXTERIOR CONTAINER WEIGHT
THE MEASURED WEIGHT OF THE EXTERIOR CONTAINER. PLEASE USE MRC AJWK WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ECWTJKG2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
SUCB*JUNIT OF ISSUE CUBE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE UNIT OF ISSUE AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUCBJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
EXME*JEXTERIOR CONTAINER CUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE EXTERIOR CONTAINER AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(EXMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information