A metallic or nonmetallic item specifically designed to be attached to a ARM, HAND CRANK parallel to its axis for transmitting motion to a shaft or object.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED42077*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEFDFEB000*;MATT3AEFDFEB000$DAL5052*;MATT3AEFDFEB000$$DAL5052*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AEF | HANDLE |
| 3AEI | WHEEL |
| 3CYA | ARM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HPQ | DRIVE END |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL3003 | ALUMINUM ALLOY 3003 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CUB000 | COPPER ALLOY |
| FEB000 | IRON CAST |
| FE0044 | IRON CAST UNS F11401 |
| FE0045 | IRON CAST UNS F11701 |
| FE0046 | IRON CAST UNS F12101 |
| FE0052 | IRON CAST UNS F12401 |
| FE0047 | IRON CAST UNS F12801 |
| FE0048 | IRON CAST UNS F13101 |
| FE0049 | IRON CAST UNS F13501 |
| FE0050 | IRON CAST UNS F13801 |
| FE0051 | IRON CAST UNS F14101 |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| STA000 | STEEL |
| ST1010 | STEEL COMP 1010 |
| ST1018 | STEEL COMP 1018 |
| ST1020 | STEEL COMP 1020 |
| ST1030 | STEEL COMP 1030 |
| ST1527 | STEEL COMP 1527 |
| ST4130 | STEEL COMP 4130 |
| ST4140 | STEEL COMP 4140 |
| ST0630 | STEEL COMP 630 |
| STB000 | STEEL CORROSION RESISTING |
| TTA000 | TITANIUM ALLOY |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AEF | HANDLE |
| 3AEI | WHEEL |
| 3CYA | ARM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HPQ | DRIVE END |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) 115, 116, 127, 150, 151 OR 162 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABSA and AAUK and AAUH and AAUJ)
IF STYLE/REPLY CODE(s) 117 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWGN and AARX)
IF STYLE/REPLY CODE(s) 118 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABNC and AARX)
IF STYLE/REPLY CODE(s) 119, 128, 130, 154, 163 OR 165 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWGN)
IF STYLE/REPLY CODE(s) 120 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AARX and AXFE and ABSF)
IF STYLE/REPLY CODE(s) 121 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AARX and ABRV and ABRR)
IF STYLE/REPLY CODE(s) 122 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AEVE and AARX and ABRV and ABRR)
IF STYLE/REPLY CODE(s) 123 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AARX)
IF STYLE/REPLY CODE(s) 124 OR 159 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWGN and AWKQ)
IF STYLE/REPLY CODE(s) 125 OR 160 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ADVR and ABGG)
IF STYLE/REPLY CODE(s) 126 OR 161 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AAUH and ADDW and AAUJ)
IF STYLE/REPLY CODE(s) 129 OR 164 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWGN and ABGG)
IF STYLE/REPLY CODE(s) 131 OR 166 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABGB and AWGN)
IF STYLE/REPLY CODE(s) 132 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AARX and ABFY and AAWZ and AAWY)
IF STYLE/REPLY CODE(s) 133 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABGE and ABFY and ABGK and AARX)
IF STYLE/REPLY CODE(s) 134 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABSF and AXFE and ABFY and AARX)
IF STYLE/REPLY CODE(s) 135 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABSF and AXFE and ADDW and ABFY and AARX)
IF STYLE/REPLY CODE(s) 136 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABSF and ABFY and AXFE and AWKQ and AWGN)
IF STYLE/REPLY CODE(s) 137 OR 138 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AFYS and AAWZ and ABFY and ABRR and AARX and AAWY)
IF STYLE/REPLY CODE(s) 139 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AAUB and AAZQ and ADVR and ASXK and AWKN)
IF STYLE/REPLY CODE(s) 152 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWGN and AWKN)
IF STYLE/REPLY CODE(s) 153 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABNC and AWKN)
IF STYLE/REPLY CODE(s) 155 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWKN and ABRV and ABRR)
IF STYLE/REPLY CODE(s) 156 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AXFE and AWKN and ABSF)
IF STYLE/REPLY CODE(s) 157 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AEVC and AXFE and AWKN and ABSF)
IF STYLE/REPLY CODE(s) 158 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWKN)
IF STYLE/REPLY CODE(s) 167 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AWKN and ABHP and AAVK and AAVH)
IF STYLE/REPLY CODE(s) 168 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABGE and ABGK and ABHP and AWKN)
IF STYLE/REPLY CODE(s) 169 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABRR and ABRV and ABHP and AWKN)
IF STYLE/REPLY CODE(s) 170 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABRR and ABRV and ADDW and ABHP and AWKN)
IF STYLE/REPLY CODE(s) 171 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (ABRR and ABRV and ABHP and AWKQ and AWGN)
IF STYLE/REPLY CODE(s) 172 OR 173 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AAST and ABSF and AAVK and ABHP and AAVH and AWKN)
IF STYLE/REPLY CODE(s) 174 WERE ENTERED FOR MRC AWJY, YOU MUST ANSWER MRC (AKRS and ABVV and ADVR and AWKP and AWKN)
AWJYLDRIVE FACILITY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE DRIVE FACILITY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AWJYL134)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAG1054 | 115 | INVOLUTE SPLINE FLAT ROOT |
| AAG1055 | 116 | INVOLUTE SPLINE FILLET ROOT |
| AAG1056 | 117 | FLATTED, TWO SIDES PARALLEL |
| AAG1057 | 118 | FLATTED, ONE SIDE |
| AAG1058 | 119 | HEXAGON |
| AAG1059 | 120 | KEY |
| AAG1060 | 121 | SINGLE KEYWAY |
| AAG1061 | 122 | PARALLEL KEYWAYS |
| AAG1062 | 123 | ROUND |
| AAG1063 | 124 | RECTANGULAR |
| AAG1064 | 125 | SECTOR |
| AAG1065 | 126 | INVOLUTE SERRATION |
| AAG1066 | 127 | PARALLEL SPLINE |
| AAG1067 | 128 | EQUIANGULAR |
| AAG1068 | 129 | FLATTED, TWO SIDES 90 DEGREES |
| AAG1069 | 130 | SQUARE |
| AAG1070 | 131 | SQUARE WITH DIAGONAL CORNER |
| AAG1071 | 132 | COUNTERBORED |
| AAG1072 | 133 | TAPERED |
| AAG1073 | 134 | INTERNAL KEY, KEY |
| AAG1074 | 135 | INVOLUTE SERRATION INTERNAL KEY |
| AAG1075 | 136 | INTERNAL KEY, RECTANGULAR |
| AAG1076 | 137 | COUNTERBORED WITH RECTANGULAR KEYWAY |
| AAI1351 | 138 | COUNTERBORED WITH ROUND KEYWAY |
| AAI1352 | 139 | PARALLEL HOLES |
| AAI1353 | 150 | INVOLUTE SPLINE FLAT ROOT |
| AAI1354 | 151 | INVOLUTE SPLINE FILLET ROOT |
| AAI1355 | 152 | FLATTED, TWO SIDES PARALLEL |
| AAI1356 | 153 | FLATTED, ONE SIDE |
| AAI1357 | 154 | HEXAGON |
| AAI1358 | 155 | KEYWAY |
| AAI1359 | 156 | SINGLE KEY |
| AAI1360 | 157 | PARALLEL KEYS |
| AAI1361 | 158 | ROUND |
| AAI1362 | 159 | RECTANGULAR |
| AAI1363 | 160 | SECTOR |
| AAI1364 | 161 | INVOLUTE SERRATION |
| AAI1365 | 162 | PARALLEL SPLINE |
| AAI1366 | 163 | EQUIANGULAR |
| AAI1367 | 164 | FLATTED TWO SIDES 90 DEG |
| AAI1368 | 165 | SQUARE |
| AAI1369 | 166 | SQUARE WITH DIAGONAL CORNER |
| AAI1370 | 167 | SHOULDERED |
| AAI1371 | 168 | TAPERED |
| AAI1372 | 169 | INTERNAL KEYWAY |
| AAI1373 | 170 | INVOLUTE SERRATION INTERNAL KEYWAY |
| AAI1374 | 171 | INTERNAL KEYWAY RECTANGULAR |
| AAI1375 | 172 | SHOULDERED WITH RECTANGULAR KEY |
| AAI1376 | 173 | SHOULDERED WITH ROUND KEY |
| AAI1377 | 174 | PARALLEL PINS |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAB2.0*;AARXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAST*JKEY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A KEY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASTJAB2.0*;AASTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJAC2.0*;AAUBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUH*JSPLINE MINOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUHJAA2.0*;AAUHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUJ*JSPLINE MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUJJAB2.0*;AAUJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUK*JSPLINE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUKJAA2.0*;AAUKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAVH*JSHOULDER DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHOULDER,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVHJAC2.0*;AAVHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAVK*JSHOULDER LENGTH
THE LENGTH OF THE ENLARGED PORTION/S/ LOCATED ON THE SHANK OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVKJAA2.0*;AAVKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWY*JCOUNTERBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWYJAC2.0*;AAWYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWZ*JCOUNTERBORE DEPTH
THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWZJAA2.0*;AAWZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZQ*JHOLE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZQJAC2.0*;AAZQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAA2.0*;ABFYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGB*JWIDTH ACROSS CORNERS
A MEASUREMENT OF THE DISTANCE DIAGONALLY FROM ONE CORNER TO THE OPPOSITE CORNER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGBJAB2.0*;ABGBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGE*JTAPERED END MINOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGEJAC2.0*;ABGEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGG*JRADIUS
THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGGJAC2.0*;ABGGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNC*JFLAT HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNCJAC2.0*;ABNCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRR*JKEYWAY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRRJAC2.0*;ABRRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRV*JKEYWAY DEPTH
A MEASUREMENT FROM THE TOP SURFACE TO THE BOTTOM OF THE KEYWAY GROOVE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRVJAC2.0*;ABRVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSF*JKEY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABSFJAA2.0*;ABSFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXFE*JKEY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF A KEY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXFEJAC2.0*;AXFEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVV*JPIN DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVVJAC2.0*;ABVVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFYS*JKEYWAY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A KEYWAY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFYSJAC2.0*;AFYSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKRS*JPIN LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE PIN,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKRSJAA2.0*;AKRSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AWGN*JDRIVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWGNJAC2.0*;AWGNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AWKN*JDRIVE FACILITY OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWKNJAB2.0*;AWKNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AWKQ*JDRIVE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWKQJAA2.0*;AWKQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGK*BTAPER ANGLE IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ABGKB2.0)
ADVR*BANGLE IN DEG
THE ANGLE FORMED BY THE ANGULAR PORTION OF THE ITEM,EXPRESSED IN DEGREES. PLEASE USE MRC CSXS IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ADVRB2.0)
ABSA*ASPLINE QUANTITY
THE NUMBER OF SPLINES ON OR IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ABSAA10*)
ADDW*ASERRATION QUANTITY
THE NUMBER OF SERRATIONS ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ADDWA10*)
AEVC*AKEY QUANTITY
THE NUMBER OF KEYS CONTAINED IN OR ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEVCA10*)
AEVE*AKEYWAY QUANTITY
THE NUMBER OF KEYWAYS CONTAINED IN OR ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEVEA10*)
ASXK*AHOLE QUANTITY
THE NUMBER OF HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ASXKA10*)
AWKP*APIN QUANTITY
THE NUMBER OF PINS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AWKPA10*)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE, NF, NM, NS, NJ OR UN WERE ENTERED FOR MRC AWJZ, YOU MUST ANSWER MRC (AWDP and CMLP and AAJF and CFHL) or (AWDP and CMLP and AAJF and APJC and AAJE)
IF STYLE/REPLY CODE(s) AM WERE ENTERED FOR MRC AWJZ, YOU MUST ANSWER MRC (AWDP and CMLP and CFHL and APJC and AAJF)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC AWJZ, YOU MUST ANSWER MRC (AWDP and CQQR and AAJF) or (AWDP and CTTC and AAJF) or (AWDP and AAJE and AAJF)
AWJZ*DDRIVE FACILITY THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A GIVEN DIAMETER OF THE DRIVE FACILITY.
Enter the applicable reply code from the table below
(AWJZDNJ)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| SM | ISO M |
| SS | ISO S |
| SJ | SI |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
AWDP*JTHREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWDPJAB2.0*;AWDPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAK4)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
CFHL*DTHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH-DIAMETER TOLERANCE AND THE EXTERNAL OR INTERNAL LOCATION OF THE THREAD.
Enter the applicable reply code from the table below
(CFHLDAS)
| Table 1 |
| Reply Code (AN53) | Reply |
| AB | 1A |
| AD | 1B |
| AE | 2A |
| AG | 2B |
| AN | 2C |
| AP | 2G |
| AJ | 3A |
| AK | 3B |
| AQ | 3C |
| AR | 3G |
| AS | 4C |
| AT | 4G |
| AW | 5C |
| AX | 6C |
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJEXTTEXT1234*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
APJC*DTHREAD LOCATION
INDICATES THE LOCATION OF THE THREAD ON THE ITEM.
Enter the applicable reply code from the table below
(APJCDABX)
| Table 1 |
| Reply Code (AJ91) | Reply |
| ABY | EXTERNAL |
| ABX | INTERNAL |
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
IF STYLE/REPLY CODE(s) AAB, AAC, AAD, AAE, AAF OR AAG WERE ENTERED FOR MRC AWKC, YOU MUST ANSWER MRC (ALMP)
AWKC*DHANDLE MOUNTING METHOD
THE MEANS USED TO ATTACH THE HANDLE TO THE ITEM.
Enter the applicable reply code from the table below
(AWKCDAMG)
| Table 1 |
| Reply Code (AM39) | Reply |
| AAC | BOLT |
| AMG | CRIMP |
| AAB | INTEGRAL |
| BCW | MACHINE SCREW |
| BGA | NUT |
| BMY | PEEN |
| AAD | PIN |
| ADC | PRESS FIT |
| AAG | RIVET |
| AAF | SETSCREW |
| AHL | SNAP RING |
| AAE | STUD |
| ACS | THREAD |
BTFP*JHANDLE MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HANDLE MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BTFPJAB2.0*;BTFPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 60, 61, 62, 63, 64, 65 OR 66 WERE ENTERED FOR MRC ALMP, YOU MUST ANSWER MRC (AASN)
ALMPLHANDLE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HANDLE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ALMPL65)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAG1037 | 60 | RECESSED FLAT |
| AAG1038 | 61 | RECESSED ROUND |
| AAG1039 | 62 | RECESSED POINT |
| AAG1040 | 63 | BALL |
| AAG1041 | 64 | ROUND |
| AAG1042 | 65 | ROUND WITH CAP |
| AAG1043 | 66 | ROUND WITH GROOVE AND CAP |
AASN*JHANDLE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASNJAB2.0*;AASNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(HUES3CYADWH0000*;HUES3CYADWH0000$DRE0000*;HUES3CYADWH0000$$DRE0000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AEF | HANDLE |
| 3CYA | ARM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| BL0033 | BLACK, FED STD 595, 37038 |
| GR0000 | GREEN |
| LD0000 | OLIVE DRAB |
| RE0000 | RED |
| WH0000 | WHITE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDPHA000*;SFTT3AEEDPHA000$DCDA000*;SFTT3AEEDPHA000$$DCDA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CYA | ARM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CRA000 | CHROMIUM |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CYA | ARM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
AWKDDHANDLE ROTATING FEATURE
AN INDICATION OF WHETHER OR NOT A HANDLE ROTATING FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(AWKDDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AWKEDHANDLE COUNTERBALANCING WEIGHT
AN INDICATION OF WHETHER OR NOT A WEIGHT IS INCLUDED TO OFFSET THE WEIGHT OF THE HANDLE.
Enter the applicable reply code from the table below
(AWKEDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AWKFDRATCHET
AN INDICATION OF WHETHER OR NOT A RATCHET IS INCLUDED.
Enter the applicable reply code from the table below
(AWKFDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AWJN*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWJNJAS2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| CH | HECTOGRAMS |
| AJ | KILOGRAMS |
| AN | OUNCES |
| AS | POUNDS |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDBB*;ABFFDHY$$DJA*)
| Table 1 |
| Reply Code (AB28) | Reply |
| GG | BOLT |
| JA | COTTER PIN |
| BB | LOCKNUT |
| DZ | LOOSE KEY |
| ED | NUT |
| GM | PIN |
| HZ | RIVET |
| GJ | SCREW |
| HY | STUD NUT |
| JB | WASHER |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDRTA000$DAUA000*;PRMTDRTA000$$DAUA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAGA000F2.0*;PMWTJAGA000F2.0$$JAGA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAGA0002.0*;PMLCJAGA0002.0$JAGA0002.0*;PMLCJAGA0002.0$$JAGA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
PKQT*AINTERMEDIATE PACKAGE QUANTITY
THE NUMBER OF WRAPS,BOXES,OR BUNDLES,WHICH CONTAINS TWO OR MORE UNITS OF ISSUE,PLACED INSIDE AN EXTERIOR CONTAINER.
Enter the numeric reply with a minimum of one digit.
(PKQTA10*)
EXQT*AEXTERIOR CONTAINER QUANTITY
THE NUMBER OF UNITS OF ISSUE PLACED INSIDE THE EXTERIOR CONTAINER. PLEASE USE MRC NMBR WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the numeric reply with a minimum of one digit.
(EXQTA10*)
SUWT*JUNIT OF ISSUE WEIGHT
THE MEASURED WEIGHT OF THE ACTUAL CONTAINER(S) OR SUPPORTING DEVICE(S) WHICH IS IN DIRECT CONTACT WITH THE ITEM AND ITS CONTENTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUWTJLB2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
ECWT*JEXTERIOR CONTAINER WEIGHT
THE MEASURED WEIGHT OF THE EXTERIOR CONTAINER. PLEASE USE MRC AJWK WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ECWTJLB2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
SUCB*JUNIT OF ISSUE CUBE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE UNIT OF ISSUE AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUCBJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
EXME*JEXTERIOR CONTAINER CUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE EXTERIOR CONTAINER AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(EXMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information