A self-contained item consisting of a water tank, electric heating element and faucet for economical dispensing of small amounts of hot water for beverage use.
expandFSC Information
7310Food Cooking, Baking, and Serving Equipment
expandColloquial Information
No Colloquials assigned to this Approve Item Name at this time
expandChange List
MRC AMKA has been deleted
MRC AFJK has been deleted
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED41977*)
AMHRJHEATING CAPACITY PER HOUR
THE RATED HEATING CAPACITY OF THE ITEM PER HOUR.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMHRJL2.0*)
Table 1
Reply Code (AB10)Reply
GGALLONS
LLITERS
CSBHJVOLTAGE IN VOLTS AND CURRENT TYPE
THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHETHER ALTERNATING OR DIRECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBHJDC2.0*;CSBHJDC2.0$$JDC2.1*)
Table 1
Reply Code (AN87)Reply
ACAC
ADAC/DC
DCDC
AMHXJTEMP RISE PER HOUR
THE NUMBER OF DEGREES THE TEMPERATURE RISES PER HOUR.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMHXJF2.0*)
Table 1
Reply Code (AB36)Reply
CCELSIUS
FFAHRENHEIT
FREQ*BFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(FREQB2.0)
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDA*;FAAZDC$DB*)
Table 1
Reply Code (AD02)Reply
ASINGLE
ESINGLE/THREE
CTHREE
BTWO
ABALDHEATING ELEMENT TYPE
INDICATES THE TYPE OF HEATING UNIT WHICH IMPARTS HEAT.
Enter the applicable reply code from the table below
(ABALDW*;ABALDP$DN*)
Table 1
Reply Code (AA93)Reply
ZANY ACCEPTABLE
NDOUBLE
PSINGLE
WTRIPLE
AMRKJHEATING ELEMENT WATTAGE RATING
THE RATED POWER WHICH A HEATING ELEMENT CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMRKJAB2.0*;AMRKJAB2.0$$JAB2.1*)
Table 1
Reply Code (AJ11)Reply
ABLOWER
AEMIDDLE
ACSINGLE
ADUPPER
ALHGDATTACHMENT DEVICE
AN INDICATION OF WHETHER OR NOT AN ATTACHMENT DEVICE IS INCLUDED.
Enter the applicable reply code from the table below
(ALHGDB*;ALHGDC$DC*)
Table 1
Reply Code (AA49)Reply
BINCLUDED
CNOT INCLUDED
AMJXDTHERMOSTATIC SWITCH
AN INDICATION OF WHETHER OR NOT A THERMOSTATIC SWITCH IS INCLUDED.
Enter the applicable reply code from the table below
(AMJXDC*;AMJXDB$DB*)
Table 1
Reply Code (AA49)Reply
BINCLUDED
CNOT INCLUDED
AEEA*DSWITCH TYPE
INDICATES THE TYPE OF SWITCH INCLUDED IN THE ITEM.
Enter the applicable reply code from the table below
(AEEADAK*;AEEADAL$DAL*)
Table 1
Reply Code (AC82)Reply
AKDOUBLE THROW
ALSINGLE THROW
AAJJJMAXIMUM OPERATING PRESSURE
THE MAXIMUM PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE. PLEASE USE MRC CQQF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAJJJP2.0*)
Table 1
Reply Code (AB18)Reply
ZKILOGRAMS
KKILOGRAMS PER SQUARE CENTIMETER
PPOUNDS
VPOUNDS PER SQUARE INCH
AHGRDINSULATED FEATURE
AN INDICATION OF WHETHER OR NOT AN INSULATED FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(AHGRDB*;AHGRDC$DC*)
Table 1
Reply Code (AA49)Reply
BINCLUDED
CNOT INCLUDED
AMLQAWATER INLET CONNECTION QUANTITY
THE NUMBER OF WATER INLET CONNECTIONS.
Enter the numeric reply with a minimum of one digit.
(AMLQA10*)
AMLLJWATER INLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE WATER INLET CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(AMLLJBS2.0*;AMLLJBS2.0$JBS2.1*)
Table 1
Reply Code (AH06)Reply
BSBSP.TR EXT
BRBSP.TR INT
FPF-PTF
SMISO M
SSISO S
NPNPT
NTNPTF
PTPTF-SAE SHORT
PPPTF-SPL
PEPTF-SPL EXTRA SHORT
PFPTF-SPL SHORT
NFUNF
NSUNS
WWWHITWORTH
AMLRAWATER OUTLET CONNECTION QUANTITY
THE NUMBER OF WATER OUTLET CONNECTIONS.
Enter the numeric reply with a minimum of one digit.
(AMLRA10*)
AMLMJWATER OUTLET CONNECTION THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF THE WATER OUTLET CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(AMLMJSM2.0*;AMLMJSM2.0$JSM2.1*)
Table 1
Reply Code (AH06)Reply
BSBSP.TR EXT
BRBSP.TR INT
FPF-PTF
SMISO M
SSISO S
NPNPT
NTNPTF
PTPTF-SAE SHORT
PPPTF-SPL
PEPTF-SPL EXTRA SHORT
PFPTF-SPL SHORT
NFUNF
NSUNS
WWWHITWORTH
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJLC2.0*;ABKWJLC2.0$$JLC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJLC2.0*;ABFYJLC2.0$$JLC2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJLB2.0*;ADUMJLB2.0$$JLB2.1*)
Table 1
Reply Code (AA05)Reply
AINCHES
LMILLIMETERS
Table 2
Reply Code (AC20)Reply
ANOMINAL
BMINIMUM
CMAXIMUM
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
Table 1
Reply Code (AN62)Reply
VFEDERAL MOTOR VEHICLE SAFETY STANDARD
FFLAMMABILITY STANDARD
SGOVERNMENT SPECIFICATION
TGOVERNMENT STANDARD
UINTERNATIONAL STD/SPEC
DMANUFACTURERS SOURCE CONTROL
RMANUFACTURERS SPECIFICATION
NMANUFACTURERS SPECIFICATION CONTROL
MMANUFACTURERS STANDARD
BNATIONAL STD/SPEC
APROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
PPROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
Table 1
Reply Code (AD08)Reply
ALALLOY
BEANNEALED
ANANNEX
APAPPENDIX
ACAPPLICABILITY CLASS
ARARRANGEMENT
ASASSEMBLY
ABASSORTMENT
BFBOND
BXBOX
CYCAPACITY
CACASE
CTCATEGORY
CFCIRCUMFERENCE
CLCLASS
CECODE
CRCOLOR
CCCOMBINATION CODE
CNCOMPONENT
CPCOMPOSITION
CMCOMPOUND
CDCONDITION
AVCONFIGURATION
CSCONSTRUCTION
BGCORE CONDITION
CBCUT OFF
AMDELAY CLASS
DEDESIGN
DGDESIGNATOR
DWDRAWING NUMBER
DUDUPLEX
EGEDGE
ENEND
FYFAMILY
FGFIGURE
AKFILE NUMBER
FNFINISH
FBFLAVOR
BHFLUX PERCENTAGE
FMFORM
FAFORMULA
AJGAGE STOCK NUMBER
GRGRADE
GAGRADUATION
AXGRANULES
AYGRIT
GBGROUND
GPGROUP
HAHEAVY DUTY
BAIMAGE COLOR
NSINSERT
TMITEM
KDKIND
KTKIT
LGLENGTH
LVLEVEL
LTLIMIT
MKMARK
AAMARKER
ADMASK APERTURE
MLMATERIAL
BBMAXIMUM DENSITY
TAMEDIUM TEMPER
MHMESH
MEMETHOD
BCMINIMUM DENSITY
MDMODEL
MTMOUNTING
AQNATURAL
AUNON-DELAY CLASS
NRNUMBER
BLOUTFIT NUMBER
PAPARAGRAPH
PTPART
PNPATTERN
PCPHYSICAL CONDITION
PSPIECE
PLPLAN
PRPOINT
PDPOLISHED
PBPRESSURE RATING
QAQUALITY
QBQUENCHED
RNRANGE
AERAPID
RTRATING
RFREFERENCE NUMBER
RAREGULAR DUTY
BJRMA FLUX
SJSALIENT CHARACTERISTICS
SCSCHEDULE
SBSECTION
SLSELECTION
BDSERIALIZED
SESERIES
SVSERVICE
SXSET
SASHADE
SHSHAPE
SGSHEET
SZSIZE
AGSLOW
TCSOFT TEMPER
SKSOURCE
PZSPECIES
SQSPECIFICATION SHEET
SDSPEED
AWSTANDARD
SRSTRAIGHT
STSTYLE
SSSUBCLASS
SFSUBFORM
SPSUBTYPE
BKSUPPORT
SNSURFACE CONDITION
SYSYMBOL
SMSYSTEM
TBTABLE
TNTANNAGE
TPTEMPER
TXTEXTURE
TKTHICKNESS
TTTREATMENT
TRTRIM
TYTYPE
YNUNIT
AZUNSERIALIZED
VAVARIETY
WTWEIGHT
WDWIDTH
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
IF STYLE/REPLY CODE(s) FN WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (AHWS)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDDS*;ENACDFM$$DDJ*)
Table 1
Reply Code (EN02)Reply
FNENERGY EFFICIENT - FEMP - RESIDENTIAL EQUIPMENT - GAS WATER HEATERS
DKHEAT PUMPS, RESIDENTIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
NRREVIEWED - DOES NOT MEET SOME ENAC CRITERIA
FMWATER HEATERS, ELECTRIC RESISTANCE, RESIDENTIAL - FEMP-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
DJWATER HEATERS, GAS, COMMERCIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
DLWATER HEATERS, GAS, RESIDENTIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
DSWATER HEATERS, SOLAR, RESIDENTIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
DMWATER HEATERS, WHOLE-HOME, TANKLESS, RESIDENTIAL - ENERGY STAR-HEATING AND COOLING - ENERGY EFFICIENT PRODUCTS
AHWS*JENERGY CONSUMPTION RATING
THE ENERGY CONSUMPTION OF THE ITEM AS DETERMINED BY A GOVERNMENT OR INDUSTRY STANDARD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHWSJAA2.0*)
Table 1
Reply Code (AD68)Reply
AAKILOWATT-HOURS OF ELECTRICITY PER 100 POUNDS (42 KG) OF ICE PRODUCED, CERTIFIED TO ARI STANDARD 810
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
Table 1
Reply Code (AN58)Reply
AADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
SUWT*JUNIT OF ISSUE WEIGHT
THE MEASURED WEIGHT OF THE ACTUAL CONTAINER(S) OR SUPPORTING DEVICE(S) WHICH IS IN DIRECT CONTACT WITH THE ITEM AND ITS CONTENTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUWTJLB2.0*)
Table 1
Reply Code (AN75)Reply
KGKILOGRAMS
LBPOUNDS
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)