An externally threaded fastener whose threaded portion is of one nominal diameter, without machined (or equivalent) surfaces, having a countersunk head surmounted by a square or hexagonal head to facilitate installation, after which the square or hexagonal head is removed. This INC was converted from AEUSA to General Use on 12/15/2020.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED40018*)
AAJFDTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AASAJTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASAJAC2.0*;AASAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASBJFASTENER LENGTH
THE DIMENSION,MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS,FROM THE LARGEST BEARING SURFACE OF THE FASTENER HEAD TO THE EXTREME OPPOSITE END,OR AS SPECIFICALLY DESIGNATED FOR OTHER TYPE FASTENERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASBJAC2.0*;AASBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANEEJGRIP LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE GRIP,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANEEJAA2.0*;ANEEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAURJGRIP DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE GRIP,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAURJAC2.0*;AAURJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AM, NS, RC, RF, RT OR WW WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP and AAJD) or (CFSG)
IF STYLE/REPLY CODE(s) BA, SJ, SK, SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CQQR and CQWR) or (CFSG)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CQQR) or (CFSG)
IF STYLE/REPLY CODE(s) TT WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP and CFSG)
IF STYLE/REPLY CODE(s) DD WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP)
IF STYLE/REPLY CODE(s) LH WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CQQR)
IF STYLE/REPLY CODE(s) NP OR SQ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM)
IF STYLE/REPLY CODE(s) JC, JE, JF, JS, NC, NE, NF, NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP and AAJD) or (CFSG)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (AHYM and CMLP) or (CQQR)
THSDDTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDMJ)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| BA | BA |
| TT | BUTTRESS |
| DD | DARDALET |
| SM | ISO M |
| SS | ISO S |
| LH | LOWENHERZ |
| EM | M |
| MJ | MJ |
| NP | NPT |
| SJ | SI |
| SK | SI-M |
| SQ | SQUARE |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NJ | UNIFIED NATIONAL JOINT (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NM | UNM |
| RC | UNRC |
| RF | UNRF |
| RT | UNRS |
| NS | UNS |
| WW | WHITWORTH |
AHYM*JNOMINAL THREAD DIAMETER
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE THREADED PORTION,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHYMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAP4)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAH4)
CQWR*AEXTERNAL THREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITIONS AND GRADES OF AN EXTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(CQWRAE0)
CFSG*JNONSTANDARD THREAD PITCH DIAMETER
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A NONSTANDARD STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CFSGJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQBC*JMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CQBCJSTEXT1234*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
CQHQ*JMINIMUM YIELD STRENGTH
THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQHQJS2*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| P | POUNDS PER SQUARE INCH |
IF STYLE/REPLY CODE(s) C1, C2, C3, C4, C8, C13 OR C16 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASU and AATB)
IF STYLE/REPLY CODE(s) C5 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (CRSQ and AATB and AASU)
IF STYLE/REPLY CODE(s) C6 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (CRSQ and AATB and AASU and AASM)
IF STYLE/REPLY CODE(s) C7, C9 OR C10 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATB and AATD and AASU and AATC)
IF STYLE/REPLY CODE(s) C11 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATC and AATD and AASU and AAZH)
IF STYLE/REPLY CODE(s) C12 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AAZH and AASU)
IF STYLE/REPLY CODE(s) C14 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (CRSQ and AATB)
IF STYLE/REPLY CODE(s) C17 OR C19 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATB and AASV and AASU)
IF STYLE/REPLY CODE(s) C18 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AATB and AASZ and AASU)
IF STYLE/REPLY CODE(s) C20 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AASX and AASR)
IF STYLE/REPLY CODE(s) C21 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AASX)
IF STYLE/REPLY CODE(s) C22 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AATB and AASU and CSYT)
IF STYLE/REPLY CODE(s) C23 OR C24 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AATB and AASU)
IF STYLE/REPLY CODE(s) C25 OR C26 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU and AASY)
IF STYLE/REPLY CODE(s) C27, C28, C29, C30, C31, C32, C33, C34, C35, C36, C37, C39, C40, C41, C43, C44, C47, C48, C57, C58, C66, C67, C68, C69, C70, C72 OR C100 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU)
IF STYLE/REPLY CODE(s) C38 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AATD and AASU and AATC)
IF STYLE/REPLY CODE(s) C45 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATC and AASL and AATD and AASU)
IF STYLE/REPLY CODE(s) C46 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (CRSQ and AASL and AASU)
IF STYLE/REPLY CODE(s) C49 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AASU)
IF STYLE/REPLY CODE(s) C50, C53 OR C54 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (CRSQ and AASL)
IF STYLE/REPLY CODE(s) C51 OR C55 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (CRSQ and AASL and AASU)
IF STYLE/REPLY CODE(s) C59 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASW and AASL and AASU and CRSQ)
IF STYLE/REPLY CODE(s) C61 OR C62 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AAST and CRSQ and AASU)
IF STYLE/REPLY CODE(s) C63 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AAST and AASL and AASU)
IF STYLE/REPLY CODE(s) C71 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATB and AASL)
IF STYLE/REPLY CODE(s) C73 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AASU and AATB)
IF STYLE/REPLY CODE(s) C76 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASQ and AASL and AASU and AASN)
IF STYLE/REPLY CODE(s) C77, C78, C79, C80, C81, C82, C83, C84, C85, C86, C87, C88, C89 OR C90 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATB and AASU)
IF STYLE/REPLY CODE(s) C64 OR C65 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATB and AASU)
IF STYLE/REPLY CODE(s) C114 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AAZG and CRSQ)
IF STYLE/REPLY CODE(s) C15 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATD and AATB and AATC and AASU)
IF STYLE/REPLY CODE(s) C91 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATB and AATC and AASU and AATD)
IF STYLE/REPLY CODE(s) C92 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASL and AATC and AASU and AATD)
IF STYLE/REPLY CODE(s) C93 OR C99 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASQ and AASU and AASL and AASN)
IF STYLE/REPLY CODE(s) C113 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASV and AASU)
IF STYLE/REPLY CODE(s) C115 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AATC and AATB and AASU and AATD)
IF STYLE/REPLY CODE(s) C116 OR C117 WERE ENTERED FOR MRC AASK, YOU MUST ANSWER MRC (AASU and AATB and AATC)
AASKLHEAD STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE HEAD.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AASKLC7)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| CF10094 | C1 | HEXAGON |
| CF10103 | C10 | DOUBLE HEXAGON W/HOLE |
| CF10187 | C100 | KNURLED NO. 5 |
| CF10188 | C101 | HEADLESS (SETSCREW) |
| CF10104 | C11 | SPLINE EXTENDED WASHER |
| CF10200 | C113 | OVAL |
| CF10201 | C114 | COUNTERSUNK CYLINDRICAL CONVEX |
| DQ00266 | C115 | TORX EXTENDED WASHER |
| DQ01038 | C116 | CHAMFER SERRATED FLANGE |
| DQ01039 | C117 | CHAMFER FLANGE |
| CF10105 | C12 | SPLINE DRIVE SHEAR HEAD |
| CF10106 | C13 | SQUARE |
| CF10107 | C14 | SQUARE COUNTERSUNK |
| CF10108 | C15 | SQUARE EXTENDED WASHER |
| CF10109 | C16 | SQUARE WEDGE |
| CF10110 | C17 | TEE NO. 1 |
| CF10111 | C18 | TEE NO. 2 |
| CF10112 | C19 | TEE NO. 3 |
| CF10095 | C2 | UNDERCUT HEXAGON |
| CF10113 | C20 | TEE NO. 4 |
| CF10114 | C21 | TEE NO. 5 |
| CF10115 | C22 | TEE NO. 6 |
| CF10116 | C23 | ROUND W/WRENCH FLATS |
| CF10117 | C24 | ROUND W/WRENCH FLATS CHAMFERED |
| CF10118 | C25 | DEE |
| CF10119 | C26 | DEE CHAMFER |
| CF10120 | C27 | DRIVE |
| CF10121 | C28 | BEVEL-CONICAL |
| CF10122 | C29 | BINDING |
| CF10096 | C3 | DISHED HEXAGON |
| CF10123 | C30 | BUTTON |
| CF10124 | C31 | OVAL |
| CF10125 | C32 | PAN |
| CF10126 | C33 | PAN NO. 2 |
| CF10127 | C34 | MODIFIED PAN |
| CF10128 | C35 | UNDERCUT PAN NO. 2 |
| CF10129 | C36 | ROOF |
| CF10130 | C37 | ROUND |
| CF10131 | C38 | ROUND EXTENDED WASHER |
| CF10132 | C39 | ROUND WEDGE |
| CF10097 | C4 | CROWNED HEXAGON |
| CF10133 | C40 | TRUSS |
| CF10134 | C41 | UNDERCUT UNIVERSAL |
| CF10135 | C43 | DOUBLE CHAMFER |
| CF10136 | C44 | FILLISTER |
| CF10137 | C45 | FILLISTER EXTENDED WASHER |
| CF10138 | C46 | FILLISTER COUNTERSUNK |
| CF10139 | C47 | FLUSH |
| CF10140 | C48 | FLAT FILLISTER |
| CF10141 | C49 | FLAT CHAMFER |
| CF10098 | C5 | HEXAGON CUNTERSUNK |
| CF10142 | C50 | FLAT COUNTERSUNK |
| CF10143 | C51 | FLAT COUNTERSUNK UNDERCUT |
| CF10144 | C53 | FLAT TOP ELEVATOR |
| CF10145 | C54 | OVAL COUNTERSUNK |
| CF10146 | C55 | OVAL COUNTERSUNK UNDERCUT |
| CF10147 | C57 | WATERTIGHT |
| CF10148 | C58 | WATERTIGHT |
| CF10149 | C59 | FLAT COUNTERSUNK KEYED |
| CF10099 | C6 | HEXAGON COUNTERSUNK UNDERCUT |
| CF10150 | C61 | FLAT COUNTERSUNK REVERSE KEYED |
| CF10151 | C62 | FLAT COUNTERSUNK REVERSE KEYED NO. 2 |
| CF10152 | C63 | FLAT KEYED |
| CF10153 | C64 | PALM GRIP |
| CF10154 | C65 | STAR KNOB |
| CF10155 | C66 | KNURLED NO. 1 |
| CF10156 | C67 | KNURLED NO. 2 |
| CF10157 | C68 | KNURLED NO. 3 |
| CF10158 | C69 | KNURLED NO. 4 |
| CF10100 | C7 | HEXAGON EXTENDED WASHER |
| CF10159 | C70 | KNURLED NO. 6 |
| CF10160 | C71 | BLIND |
| CF10161 | C72 | BALL |
| CF10162 | C73 | SPADE |
| CF10163 | C76 | SWIVEL HANDLE |
| CF10164 | C77 | THUMB NO. 1 |
| CF10165 | C78 | THUMB NO. 2 |
| CF10166 | C79 | THUMB NO. 3 |
| CF10101 | C8 | DOUBLE HEXAGON |
| CF10167 | C80 | THUMB NO. 4 |
| CF10168 | C81 | THUMB NO. 5 |
| CF10169 | C82 | THUMB NO. 6 |
| CF10170 | C83 | THUMB NO. 7 |
| CF10171 | C84 | THUMB NO. 8 |
| CF10172 | C85 | THUMB NO. 9 |
| CF10173 | C86 | WING N0. 1 |
| CF10174 | C87 | WING N0. 2 |
| CF10175 | C88 | WING N0. 3 |
| CF10176 | C89 | WING N0. 4 |
| CF10102 | C9 | DOUBLE HEXAGON EXTENDED WASHER |
| CF10177 | C90 | DISTORTED HEAD |
| CF10178 | C91 | DOUBLE HEXAGON EXTENDED WASHER |
| CF10179 | C92 | FLAT EXTENDED WASHER |
| CF10180 | C93 | FIXED HANDLE |
| CF10186 | C99 | SLIDING HANDLE |
AASL*JHEAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HEAD,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASLJAA2.0*;AASLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASM*JBOTTOM COUNTERSINK DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASMJAC2.0*;AASMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASN*JHANDLE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HANDLE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASNJAA2.0*;AASNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASQ*JHANDLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HANDLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASQJAC2.0*;AASQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASR*JHEAD INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASRJAB2.0*;AASRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAST*JKEY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A KEY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASTJAB2.0*;AASTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASU*JHEAD HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE HEAD,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASUJAB2.0*;AASUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASV*JHEAD LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A HEAD,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASVJAA2.0*;AASVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASW*JKEY PROJECTION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASWJAA2.0*;AASWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASX*JTEE BOLT CYLINDRICAL HEAD DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASXJAC2.0*;AASXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASY*JDISTANCE FROM CENTERLINE TO FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASYJAC2.0*;AASYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASZ*JTEE HEAD FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASZJAB2.0*;AASZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATB*JWIDTH BETWEEN FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATBJAC2.0*;AATBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATC*JEXTENDED WASHER DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATCJAC2.0*;AATCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATD*JEXTENDED WASHER THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATDJAB2.0*;AATDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZG*JHEAD MAJOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZGJAA2.0*;AAZGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZH*JHEAD MINOR DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZHJAA2.0*;AAZHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRSQ*JCOUNTERSINK ANGLE
THE INCLUDED ANGLE OF THE COUNTERSINK.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRSQJDA2.0*;CRSQJDA2.0$$JDA2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSYT*JCHAMFER ANGLE
THE INCLUDED ANGLE OF THE CHAMFER(S).
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYTJRC2.0*;CSYTJRC2.0$$JRC2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCQX*;CBBLDBBW$$DCMU*)
| Table 1 |
| Reply Code (AN47) | Reply |
| CQU | BOOT TYPE WASHER |
| CMU | BUSHING |
| AEQ | CASEHARDENED |
| CQV | CETYL ALCOHOL LUBRICANT |
| AFP | COTTER PIN |
| CVQ | DRY FILM LUBRICANT |
| CTE | DULL FINISH |
| BBT | FINISHED HEAD |
| CQW | FLAT WASHER |
| CQX | HEX NUT |
| AFY | LOCK WASHER |
| BBL | LOCKNUT |
| AFZ | NUT |
| AGA | O RING |
| CQY | RETAINING CLIP |
| ALT | SEALING RING |
| CQZ | SHIM |
| CRA | SLEEVE |
| CRB | SPACER |
| CRC | SQUARE NUT |
| BBW | UNFINISHED HEAD |
| BEQ | WASHER |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRTA000*;PRMTDPDA000$DIRA000*;PRMTDPDA000$$DIRA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAZA000F2.0*;PMWTJAZA000F2.0$$JAZA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDAK)
| Table 1 |
| Reply Code (EN02) | Reply |
| AK | NON-CADMIUM PRODUCT |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ027*;HZRDDHAZ092$$DHAZ285*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
| HAZ011 | CHROMIUM |
| HAZ012 | COPPER |
| HAZ027 | IRIDIUM |
| HAZ222 | IRON |
| HAZ029 | LEAD |
| HAZ092 | MAGNESIUM |
| HAZ030 | MAGNESIUM ALLOY |
| HAZ252 | NICKEL |
| HAZ285 | PLASTIC |
| HAZ286 | PLATINUM |
| HAZ303 | SILVER |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information