A hydraulic system component designed to distribute fluids between components such as accumulators, restrictors, valves, filters and the like. It includes some or all of the above components.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED37908*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDNLA000*;MATTDAL0046$DTTA000*;MATTDAL0046$$DTTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| ZTE000 | ALUMINUM ALLOY 2014, TYPE 6 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AM2024 | ALUMINUM ALLOY 2024, TYPE 3 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL6013 | ALUMINUM ALLOY 6013 |
| AL6061 | ALUMINUM ALLOY 6061 |
| ZSJ001 | ALUMINUM ALLOY 6061, TYPE 6 |
| ZSA003 | ALUMINUM ALLOY 6061, TYPE 651 |
| ZSA001 | ALUMINUM ALLOY 6061, TYPE 6510 |
| ZSA002 | ALUMINUM ALLOY 6061, TYPE 6511 |
| ZSV000 | ALUMINUM ALLOY 7075, TYPE 73 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| CUB000 | COPPER ALLOY |
| CU0075 | COPPER ALLOY 24 |
| CU0088 | COPPER ALLOY 342 |
| CU0092 | COPPER ALLOY 377 |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| FEC000 | IRON MALLEABLE |
| MGA000 | MAGNESIUM |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| RCE000 | RUBBER |
| AGA000 | SILVER |
| STA000 | STEEL |
| ST1009 | STEEL COMP 1009 |
| ST0303 | STEEL COMP 303 |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0321 | STEEL COMP 321 |
| ST0452 | STEEL COMP 321H |
| ST0347 | STEEL COMP 347 |
| STB000 | STEEL CORROSION RESISTING |
| TTA000 | TITANIUM ALLOY |
IF STYLE/REPLY CODE(s) AAP, AAV OR AAM WERE ENTERED FOR MRC AWLS, YOU MUST ANSWER MRC (AAAR)
IF STYLE/REPLY CODE(s) AAQ, AAW, AAX OR AAN WERE ENTERED FOR MRC AWLS, YOU MUST ANSWER MRC (CWFD)
IF STYLE/REPLY CODE(s) AAR OR AAS WERE ENTERED FOR MRC AWLS, YOU MUST ANSWER MRC (BJDR and AERZ)
IF STYLE/REPLY CODE(s) AAT OR AAU WERE ENTERED FOR MRC AWLS, YOU MUST ANSWER MRC (AAMW)
IF STYLE/REPLY CODE(s) AAY, AAZ, AAK, AAL, ABA, ABB, ABC OR ABD WERE ENTERED FOR MRC AWLS, YOU MUST ANSWER MRC (THSD)
AWLSDCONNECTION TYPE
INDICATES THE TYPE OF CONNECTION/S/.
Enter the applicable reply code from the table below
(AWLSDAAS*;AWLSDAAQ$$DAAX*)
| Table 1 |
| Reply Code (AB76) | Reply |
| AAM | BRAZING, PIPE |
| AAN | BRAZING, TUBE |
| AAP | BUTT WELD PIPE |
| AAQ | BUTT WELD TUBE |
| AAR | FLANGE, RECTANGULAR W/HOLES |
| AAS | FLANGE, RECTANGULAR W/O HOLES |
| AAT | FLANGE, ROUND W/HOLES |
| AAU | FLANGE, ROUND W/O HOLES |
| AAV | SOCKET, WELD, PIPE |
| AAW | SOCKET, WELD, TUBE |
| AAX | SOLDER, TUBE |
| AAY | THREADED EXTERNAL BOSS |
| AAZ | THREADED EXTERNAL HOSE |
| AAK | THREADED EXTERNAL PIPE |
| ABA | THREADED EXTERNAL TUBE |
| ABB | THREADED INTERNAL BOSS |
| ABC | THREADED INTERNAL HOSE |
| AAL | THREADED INTERNAL PIPE |
| ABD | THREADED INTERNAL TUBE |
ADQZAEND CONNECTION QUANTITY
THE NUMBER OF END CONNECTIONS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ADQZA10*)
CYJBAEND ITEM DESIGN CONTROL ACTIVITY
THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE END ITEM.
Enter the alpha-numeric reply with five character(s) exactly.
(CYJBAK2P7A)
CYJDAEND ITEM IDENTIFICATION DESIGNATOR
THE NAME OR COMBINED GROUP OF LETTERS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC END ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(CYJDAS0)
MEDA*DMEDIA FOR WHICH DESIGNED
THE TYPE OF MEDIA FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(MEDADAFK*;MEDADACE$DAAT*;MEDADACE$$DAAT*)
| Table 1 |
| Reply Code (AN91) | Reply |
| AAS | HYDRAULIC FLUID |
| AGB | HYDRAULIC FLUID, ARYL PHOSPHATE ESTER |
| ADB | HYDRAULIC FLUID, MIL-H-5606 |
| AGT | HYDRAULIC FLUID, MINERAL BASE |
| ACD | HYDRAULIC FLUID, PETROLEUM BASE |
| AAW | HYDRAULIC FLUID, PHOSPHATE-ESTER BASE |
| AAX | HYDRAULIC FLUID, SILICATE-ESTER BASE |
| AFK | HYDRAULIC FLUID, SYNTHETIC HYDROCARBON BASE |
| AAT | HYDRAULIC FLUID, WATER BASE |
| ALS | NONMINERAL OIL |
| ALM | NONPETROLEUM BASE HYDRAULIC FLUID |
| ACE | OIL, HYDRAULIC |
| ADL | OIL, HYDROCARBON BASE |
| ADE | OIL, LUBRICATING |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDAAA000*;SFTTDCDA000$DANA000*;SFTTDCDA000$$DANA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| AAA001 | CARC (CHEMICAL AGENT RESISTANT COATING) |
| AAA002 | CHEMICAL |
| AAA000 | PAINTED |
| PSA000 | PASSIVATE |
| AAA015 | PASSIVATED INORGANIC COATING |
| PRA000 | PRIMER |
| PRF000 | PRIMER EPOXY |
| PRA001 | PRIMER EPOXY-LEAD AND CHROMIUM FREE |
| ZNM000 | PRIMER-HEXAVALENT CHROMIUM FREE |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDBL0000*;HUESDWH0000$DGY0000*;HUESDWH0000$$DGY0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| GY0000 | GRAY/GREY |
| WH0000 | WHITE |
ALBY*DUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDAHX*;ALBYDABX$$DAMF*)
| Table 1 |
| Reply Code (AH21) | Reply |
| AHX | AIRCRAFT |
| ABX | HELICOPTER |
| AHY | SHIP |
| AMF | VEHICULAR |
ALCD*GUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALCDGCLEARTEXT)
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
AKVU*BOPERATING PRESSURE IN PSI
THE REQUIRED OPERATING PRESSURE EXPRESSED IN POUNDS PER SQUARE INCH.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AKVUB2.0)
AFGA*JOPERATING TEMP RANGE
THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFGAJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| K | KELVIN |
CSWK*JBURST PRESSURE
THE MINIMUM INTERNAL PRESSURE AT WHICH THE ITEM CAN BE EXPECTED TO RUPTURE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSWKJEKBD2.0*;CSWKJEKBD2.0$$JEKBD2.1*)
| Table 1 |
| Reply Code (AL15) | Reply |
| EK | PRESSURE |
| FA | VACUUM |
| Table 2 |
| Reply Code (AG20) | Reply |
| DA | BAR |
| AV | KILOGRAMS PER SQUARE CENTIMETER |
| DK | MEGAPASCALS |
| BA | POUND |
| CA | POUNDS PER MINUTE |
| BB | POUNDS PER SQUARE INCH |
| BC | POUNDS PER SQUARE INCH ABSOLUTE |
| BD | POUNDS PER SQUARE INCH GAGE |
AAAR*JNOMINAL PIPE SIZE ACCOMMODATED
A MEASUREMENT OF THE PIPE SIZE THE ITEM WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAARJA2.0*;AAARJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQJB*JPROOF PRESSURE
THE MAXIMUM PRESSURE THAT AN ITEM WILL WITHSTAND WITHOUT RESULTING IN ANY PERMANENT CHANGES IN THE STRUCTURAL,MECHANICAL,OR ELECTRICAL CHARACTERISTICS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJBJBB2.0*)
| Table 1 |
| Reply Code (AG20) | Reply |
| AV | KILOGRAMS PER SQUARE CENTIMETER |
| CD | MILLIMETERS PER SECOND |
| BA | POUND |
| CA | POUNDS PER MINUTE |
| BB | POUNDS PER SQUARE INCH |
| BD | POUNDS PER SQUARE INCH GAGE |
AMPS*BCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0*;AMPSB2.0$BM2.0;AMPSB2.0$$BM2.0*)
CWFD*JNOMINAL OUTSIDE DIAMETER TUBE ACCOMMODATED
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWFDJA2.0*;CWFDJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
APNE*BOPERATING VOLTAGE IN VOLTS
AN INDICATION OF THE AMOUNT OF OPERATING VOLTAGE,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APNEB2.0)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
IF YOU ANSWER MRC THSD, YOU MUST ANSWER MRC (CQJX)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDSH*;THSDDNC$$DNF*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| SH | NPSH |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NS | UNS |
AQXP*AINLET CONNECTION QUANTITY
THE NUMBER OF INLET CONNECTIONS ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AQXPA10*)
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*;CQJXJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAMW*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAMWJA2.0*;AAMWJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ARTG*AOUTLET CONNECTION QUANTITY
THE NUMBER OF OUTLET CONNECTIONS ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ARTGA10*)
BJDR*JFLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A FLANGE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BJDRJA2.0*;BJDRJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CYCJ*APORT QUANTITY
THE NUMBER OF PORTS PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(CYCJA10*)
AERZ*JFLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLANGE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AERZJA2.0*;AERZJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
AJJW*ACOMPONENT QUANTITY
THE NUMBER OF COMPONENTS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJJWA10*)
CQGM*JMAXIMUM OPERATING PRESSURE
THE MAXIMUM PRESSURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQGMJK2.0*)
| Table 1 |
| Reply Code (AN71) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| P | POUNDS PER SQUARE INCH |
| G | POUNDS PER SQUARE INCH GAGE |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAX1)
ACHY*DMOUNTING HOLE TYPE
INDICATES THE TYPE OF HOLES PROVIDED IN THE ITEM TO FACILITATE MOUNTING TO ANOTHER ITEM.
Enter the applicable reply code from the table below
(ACHYDA*;ACHYDC$DB*;ACHYDC$$DB*)
| Table 1 |
| Reply Code (AB68) | Reply |
| A | COUNTERBORED |
| B | COUNTERSUNK |
| C | PLAIN |
| P | SLOTTED |
| D | THREADED |
| E | UNTHREADED |
CZNF*ACOLOR CHIP NUMBER
THE IDENTIFYING NUMBER FOR THE COLOR CHIP.
Enter the alpha-numeric reply with a minimum of one character.
(CZNFAV1)
TMQY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TMQYJACH2*;TMQYJACH2$$JACH3*)
| Table 1 |
| Reply Code (AB28) | Reply |
| BHH | ACCUMULATOR |
| ACH | ADAPTER |
| ACJ | BRAZING RING |
| BWG | CAM LOCKING COUPLING HALF |
| BQR | ELBOW |
| AKH | FERRULE |
| AZA | FILTER |
| BWK | FITTING |
| ABW | NUT |
| AXZ | O-RING |
| AEA | PLUG |
| BSC | PRESSURE GAGE |
| BWH | QUICK DISCONNECT COUPLING HALF |
| AFB | RESTRICTOR |
| BWL | ROLLOVER FRAME |
| BWM | SAND TRAP |
| BWJ | SPLIT CLAMP COUPLING HALF |
| BWN | TEE |
| BQG | TUBE |
| BHJ | VALVE |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJLA2.0*;ABHPJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJLC2.0*;ABKWJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJLC2.0*;ABTBJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAE4)
ACUN*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM. THIS MRC IS BEING DISCONTINUED. PLEASE USE MRC AXGY IF AVAILABLE.
Enter the applicable reply code from the table below
(ACUNDAPP)
| Table 1 |
| Reply Code (AB89) | Reply |
| APP | BOLTED |
| ACJ | SCREW |
| APL | WELDED |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CYHE*JOPERATING TEMPERATURE RANGE
THE MINUS AND/OR PLUS DEGREES OF TEMPERATURE THE ITEM CAN WITHSTAND WITHOUT GIVING ERRONEOUS ASSAY DATA.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CYHEJLM2.0*;CYHEJLM2.0$$JLM2.1*)
| Table 1 |
| Reply Code (AB39) | Reply |
| K | DEG CELSIUS |
| L | DEG FAHRENHEIT |
| Table 2 |
| Reply Code (AH08) | Reply |
| M | MINUS |
| P | PLUS |
ALVY*JRETURN PRESSURE
THE AMOUNT OF PRESSURE BEING RETUNED TO THE OUTLET VALVES/PORTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALVYJBC2.0*;ALVYJBC2.0$$JBC2.1*)
| Table 1 |
| Reply Code (AG20) | Reply |
| BB | POUNDS PER SQUARE INCH |
| BC | POUNDS PER SQUARE INCH ABSOLUTE |
| BD | POUNDS PER SQUARE INCH GAGE |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information