Designed to dissipate the energy of low speed bumper impacts and provide protection to the vehicle bumper, body and frame within a specific speed range. The unit combines a charged volume of gas separated from hydaulic fluid by a floating piston or the like, the charged gas volume restores the bumper to its original position after impact within the specific speed range. The unit is normally mounted to the vehicle frame on one end and bumper mounting accommodations on the opposite end.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED37317*)
APHEDOPERATION METHOD
THE MEANS USED TO OPERATE THE ITEM.
Enter the applicable reply code from the table below
(APHEDAAE)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAB | AIR |
| ADD | FRICTION |
| ADE | GAS |
| AAE | HYDRAULIC |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXMR and CXKC and CXMY and CXMK)
IF STYLE/REPLY CODE(s) 4, 5, 6 OR 7 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXKS and CXKK)
IF STYLE/REPLY CODE(s) 8, 9 OR 10 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXKK and CXKN and CXKG)
IF STYLE/REPLY CODE(s) 11, 13 OR 15 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXLB and CXKS and CXLF)
IF STYLE/REPLY CODE(s) 12 OR 14 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXLB and CXLF and CXKY and CXKS)
IF STYLE/REPLY CODE(s) 16 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXLM and CXLX and CXKY and CXLR and CXMB and CXMF and CXKS)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXLM and CXKS and CXLR and CXLF)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXKC and CXMK and CXMY and CXMR)
IF STYLE/REPLY CODE(s) 18 WERE ENTERED FOR MRC BXYS, YOU MUST ANSWER MRC (CXMY and CXMK and CXMR)
BXYSLPISTON END CONNECTION STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PISTON END CONNECTION.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BXYSL16)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAL1001 | 1 | STRAIGHT STEM/STUD MOUNT |
| AAL1010 | 10 | CROSS PIN MOUNYING, DRILLED AND SLOTTED |
| AAL1011 | 11 | RING |
| AAL1012 | 12 | RING |
| AAL1013 | 13 | BEARING |
| AAL1014 | 14 | BEARING, TAPERED |
| AAL1015 | 15 | BEARING, STRAIGHT |
| AAL1016 | 16 | FORK |
| AAL1017 | 17 | TONGUE |
| DQ00712 | 18 | BAYONET TYPE |
| AAL1002 | 2 | DOUBLE STUD MOUNT |
| AAL1003 | 3 | SHOULDERED STEM |
| AAL1004 | 4 | LOOP MOUNTING |
| AAL1005 | 5 | BUSHING AND SLEEVE |
| AAL1006 | 6 | BUSHING AND SLEEVE, EXTENDED |
| AAL1007 | 7 | CAPTURED BUSHING |
| AAL1008 | 8 | CROSS PIN MOUNTING, SLOTTED |
| AAL1009 | 9 | CROSS PIN MOUNTING, DRILLED |
CXKC*JPISTON END NOMINAL CONNECTION THREAD SIZE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKCJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXKG*JPISTON END NOMINAL HOLE CENTER TO CENTER DISTANCE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXKK*JPISTON END NOMINAL OVERALL LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKKJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXKN*JPISTON END NOMINAL BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKNJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXKS*JPISTON END NOMINAL INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKSJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXKY*JPISTON END NOMINAL LARGEST INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXLB*JPISTON END NOMINAL OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXLBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXLF*JPISTON END NOMINAL THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXLFJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXLM*JPISTON END NOMINAL WIDTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXLMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXLR*JPISTON END NOMINAL FORK DEPTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXLRJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXLX*JPISTON END NOMINAL FORK ARM THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXLXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXMB*JPISTON END NOMINAL RIGHT FORK ARM THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXMBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXMF*JPISTON END NOMINAL FORK SPAN WIDTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXMFJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXMK*JPISTON END NOMINAL SHANK LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXMKJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXMR*JPISTON END NOMINAL SHANK DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXMRJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXMY*JPISTON END NOMINAL SHANK UNTHREADED LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXMYJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXQT and CXND and CXQX and CXQP)
IF STYLE/REPLY CODE(s) 4, 5, 6 OR 7 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXNW and CXNL)
IF STYLE/REPLY CODE(s) 8, 9 OR 10 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXNL and CXNR and CXNH)
IF STYLE/REPLY CODE(s) 11, 13 OR 15 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXPG and CXNW and CXPM)
IF STYLE/REPLY CODE(s) 12 OR 14 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXPG and CXPM and CXPB and CXNW)
IF STYLE/REPLY CODE(s) 16 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXPQ and CXPZ and CXPB and CXPT and CXQF and CXQK and CXNW)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXPQ and CXNW and CXPT and CXPM)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXND and CXQP and CXQX and CXQT)
IF STYLE/REPLY CODE(s) 18 WERE ENTERED FOR MRC BYBF, YOU MUST ANSWER MRC (CXQX and CXQP and CXQT)
BYBFLCYLINDER END CONNECTION STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CYLINDER END CONNECTION.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BYBFL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAL1001 | 1 | STRAIGHT STEM/STUD MOUNT |
| AAL1010 | 10 | CROSS PIN MOUNTING, DRILLED AND SLOTTED |
| AAL1011 | 11 | RING |
| AAL1012 | 12 | RING |
| AAL1013 | 13 | BEARING |
| AAL1014 | 14 | BEARING TAPERED |
| AAL1015 | 15 | BEARING, STRAIGHT |
| AAL1016 | 16 | FORK |
| AAL1017 | 17 | TONGUE |
| DQ00712 | 18 | BAYONET TYPE |
| AAL1002 | 2 | CROSS PIN MOUNTING, DRILLED AND SLOTTED |
| AAL1003 | 3 | SHOULDERED STEM |
| AAL1004 | 4 | LOOP MOUNTING |
| AAL1005 | 5 | BUSHING AND SLEEVE |
| AAL1006 | 6 | BUSHING AND SLEEVE, EXTENDED |
| AAL1007 | 7 | CAPTURED BUSHING |
| AAL1008 | 8 | CROSS PIN MOUNTING, SLOTTED |
| AAL1009 | 9 | CROSS PIN MOUNTING, DRILLED |
CXND*JCYLINDER END NOMINAL CONNECTION THREAD SIZE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNDJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXNH*JCYLINDER END NOMINAL HOLE CENTER TO CENTER DISTANCE
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNHJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXNL*JCYLINDER END NOMINAL OVERALL LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNLJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXNR*JCYLINDER END NOMINAL BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNRJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXNW*JCYLINDER END NOMINAL INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNWJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXPB*JCYLINDER END NOMINAL LARGEST INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXPBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXPG*JCYLINDER END NOMINAL OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXPGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXPM*JCYLINDER END NOMINAL THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXPMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXPQ*JCYLINDER END NOMINAL WIDTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXPQJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXPT*JCYLINDER END NOMINAL FORK DEPTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXPTJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXPZ*JCYLINDER END NOMINAL FORK ARM THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXPZJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXQF*JCYLINDER END NOMINAL RIGHT FORK ARM THICKNESS
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQFJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXQK*JCYLINDER END NOMINAL FORK SPAN WIDTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQKJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXQP*JCYLINDER END NOMINAL SHANK LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQPJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXQT*JCYLINDER END NOMINAL SHANK DIAMETER
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQTJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXQX*JCYLINDER END NOMINAL SHANK UNTHREADED LENGTH
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXQXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXDZJNOMINAL EXTENDED LENGTH
A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM WHEN IN AN EXTENDED POSITION,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXDZJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXFNJNOMINAL COMPRESSED LENGTH
A NOMINAL MEASUREMENT OF THE SMALLEST LENGTH TO WHICH THE ITEM MAY BE COMPRESSED,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXFNJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CXFWDPROTECTIVE SHIELD TYPE
INDICATES THE TYPE OF SHIELD.
Enter the applicable reply code from the table below
(CXFWDAV)
| Table 1 |
| Reply Code (AG94) | Reply |
| AG | DUST |
| AU | NO PROTECTION |
| AV | STONE |
TMQY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TMQYJBHZ2*;TMQYJBHZ2$$JBHZ3*)
| Table 1 |
| Reply Code (AB28) | Reply |
| BHX | BODY NUT |
| BHY | BODY NUT ASSEMBLY |
| BHZ | BODY NUT SPACER |
| ABR | BOLT |
| ABS | BRACKET |
| BJA | BRAKE LINE BRACKET PLATE |
| AJM | BUSHING |
| BJB | CASTLE NUT |
| BJC | CENTERING COLLAR |
| BJD | CENTERING WASHER |
| BJE | COMPRESSION BUMPER |
| BJF | CONNECTING LINK |
| BJG | CONSTANT RATE SPRING |
| BCA | COTTER PIN |
| BJH | DRILLED LOCKING DEVICE |
| BJJ | FLAT HEAD MACHINE SCREW |
| BJK | FLAT HEAD SCREW |
| ACA | FLAT WASHER |
| BJL | HEX FLANGE LOCK NUT |
| BJM | HEX HEAD EXTENSION NUT |
| BJN | HEX JAM NUT |
| BCG | HEXAGON BOLT |
| ASP | HEXAGON NUT |
| BJP | INNER COLLAR |
| BJQ | INSTRUCTION SHEET |
| BJR | KNURLED BOLT |
| ACB | LOCK WASHER |
| BJS | LOWER MOUNTING BOLT |
| BJT | MACPHERSON BODY NUT |
| AEK | MOUNTING BRACKET |
| APJ | MOUNTING PLATE |
| ABW | NUT |
| BJU | OUTER COLLAR |
| BJV | OUTER RETAINING WASHER |
| BJW | PALNUT |
| BJX | PISTON ROD NUT |
| BGG | RETAINER |
| BJY | RETAINING WASHER |
| BJZ | RUBBER BOOT RETAINING RING |
| BKA | RUBBER BUMPER |
| BKB | RUBBER BUSHING |
| BKC | SELF-CENTERED BUSHING |
| AXX | SELF-LOCKING NUT |
| BKD | SHEET METAL LOCK NUT |
| ACX | SLEEVE |
| ATD | SPACER |
| BKE | SPECIAL SHOULDERED SPACER |
| BKF | SPRING SEAT SPACER |
| BKG | STRIKER CAP |
| AFN | STUD |
| BKH | STUD ASSEMBLY |
| BKJ | STUD NUT |
| BKK | TORX HEAD NUT |
| BKL | TWO-PIECE BUSHING |
| BKM | VARIABLE RATE SPRING |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAQ0)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information