An engineered panel composed of an assembly of layers of plies of veneer joined with a moisture-resistant or 100 pct. waterproof glueline. The grain of alternate layers is perpendicular. The face, back, and inner plies are almost always a softwood species as described in recognized standards. This plywood is most widely used for construction purposes.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED36785*)
CSTSDTYPICAL WOOD PRODUCTS USE
THE REQUIRED PURPOSE OR APPLICATION OF THE TYPICAL WOOD PRODUCTS FOR WHICH THE ITEM IS INTENDED.
Enter the applicable reply code from the table below
(CSTSDEJ)
| Table 1 |
| Reply Code (AP62) | Reply |
| DX | BOAT AND SHIP CONSTRUCTION ONLY |
| DY | BOAT AND SHIP CONSTRUCTION ONLY OVERLAID WHERE THE OVERLAY PREVENTS CHECKING AND IS READILY PAINTABLE |
| EA | CONCRETE FORMS WITH BLEMISH-FREE SURFACE AND REUSABLE |
| EB | DECORATIVE INTERIOR USE REQUIRING HIGHEST APPEARANCE OF ONE SIDE ONLY |
| EC | EXTERIOR USE UTILITY PANEL FOR WORK BUILDINGS, BOX CAR AND TRUCK LININGS, CONTAINERS AND AS BASE FOR EXTERIOR COATINGS FOR WALL AND ROOFS |
| ED | EXTERIOR USE WHERE APPEARANCE OF ONLY ONE SIDE IS IMPORTANT SUCH AS SOFFETS, FENCES, STRUCTURAL USE, BOX CAR LININGS AND GABLE ENDS |
| EE | EXTERIOR USE WHERE TWO SOLID SURFACES NECESSARY BUT APPEARANCE ON ONE SIDE LESS IMPORTANT AND PAINTABLE SUCH AS SIGNS AND CARPORTS |
| EF | EXTERIOR USES SUCH AS SUBFLOORING, ROOF DECKING, CRATING AND PALLETS |
| EG | EXTERIOR USES SUCH AS THE TILE BACKING WHERE SEVERE MOISTURE CONDITIONS EXIST, REFRIGERATED OR CONTROLLED ATMOSPHERE ROOMS AND OPEN SOFFITS |
| EH | EXTERIOR USES SUCH AS WALL AND ROOF SHEATHING, SUBFLOORING, INDUSTRIAL USES AND CONTAINERS FOR WHEN CONSTRUCTION DELAYS ARE ANTICIPATED |
| EJ | FABRICATION OF STRUCTURAL OR HIGHLY STRESSED AIRCRAFT PARTS |
| EK | INTERIOR USE FOR APPLICATIONS WITH BOTH SIDES ON VIEW SUCH AS BUILT-INS, CABINETS AND PARTITIONS |
| EL | INTERIOR USE UTILITY PANEL WITH ONE SOLID SIDE FOR BACKING, SLIPSSHEETS AND BINS |
| EM | INTERIOR USE WHERE APPEARANCE OF ONLY ONE SIDE IS IMPORTANT SUCH AS PANELING, CEILING AND DISPLAYS |
| EN | INTERIOR USE WHERE TWO SOLID SURFACES NECESSARY BUT APPEARANCE ON ONE SIDE LESS IMPORTANT AND PAINTABLE |
| EP | INTERIOR USES SUCH AS WALL AND ROOF SHEATHING, SUBFLOORING, PALLETS AND CONTAINERS |
| EQ | STRUCTURAL GRADES WHERE PLYWOOD STRENGTH PROPERTIES ARE OF MAXIMUM IMPORTANCE |
| ER | UNDERLAYMENT FOR APPLICATION OVER STRUCTURAL SUBFLOOR |
| ES | USES REQUIRING HARD, TRANSLUCENT, ABRASION RESISTANT SURFACES SUCH AS SIGNS, COUNTER AND TABLE TOPS, CABINETS AND PAINTING NOT REQUIRED |
| ET | VENEER FOR CONTAINERS FOR USE IN LIEU OF PLYWOOD 1/4 INCH OR LESS IN THICKNESS |
CSTTHPLYWOOD SPECIES AND GRADE
AN INDICATION OF THE PLYWOOD SPECIES AND GRADE OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CSTTHDLBC2.0*;CSTTHDLBC2.0$HDLBC2.1*)
| Table 1 |
| Reply Code (AM00) | Reply |
| DM | ALDER |
| DN | ALDER, RED |
| AA | ANY ACCEPTABLE |
| AB | ASH |
| DP | ASH, BLACK |
| DD | ASH, WHITE |
| DR | ASPEN |
| AS | BALSA |
| AT | BASSWOOD |
| DS | BASSWOOD, AMERICAN |
| AW | BEECH |
| DT | BEECH, AMERICAN |
| AX | BIRCH |
| DW | BIRCH, SWEET |
| DX | BIRCH, YELLOW |
| DY | BOXELDER |
| DZ | BUCKEYE |
| EA | BUTTERNUT |
| AH | CEDAR |
| FR | CEDAR, ALASKA |
| EC | CEDAR, ATLANTIC WHITE |
| ED | CEDAR, EASTERN RED |
| ET | CEDAR, INCENSE |
| EE | CEDAR, NORTHERN WHITE |
| FS | CEDAR, PORT ORFORD |
| EB | CEDAR, WESTERN |
| AN | CEDAR, WESTERN RED |
| BB | CHERRY |
| EF | CHERRY, BLACK |
| BC | CHESTNUT |
| HN | COACHWOOD |
| EG | COTTONWOOD |
| AJ | CYPRESS |
| AD | DOUGLAS FIR |
| HK | DOUGLAS-FIR, COASTAL |
| HL | DOUGLAS-FIR, SOUTH, INTERIOR |
| BF | ELM |
| EH | ELM, AMERICAN |
| EJ | ELM, ROCK |
| AE | FIR |
| EK | FIR, BALSAM |
| EL | FIR, GRAND |
| EM | FIR, SUBALPINE |
| BH | GUM |
| EN | GUM, BLACK |
| CW | GUM, SWEET |
| EQ | HACKBERRY |
| CC | HARDWOOD |
| FW | HEM-FIR |
| BJ | HEMLOCK |
| ER | HEMLOCK, EASTERN |
| ES | HEMLOCK, MOUNTAIN |
| DA | HEMLOCK, WESTERN |
| AC | HICKORY |
| EW | HOLLY |
| BN | LARCH |
| EX | LAUAN |
| EY | LIGNUM VITAE |
| BP | LOCUST |
| AY | LOCUST, BLACK |
| FA | LOCUST, HONEY |
| DQ | MAGNOLIA |
| BS | MAHOGANY |
| HQ | MAHOGANY, GABOON |
| BT | MAPLE |
| EZ | MAPLE, BLACK |
| EP | MAPLE, HARD |
| FB | MAPLE, RED |
| FC | MAPLE, SILVER |
| FD | MAPLE, SOFT |
| FE | MAPLE, SUGAR |
| AF | OAK |
| CK | OAK, RED |
| DG | OAK, WHITE |
| FF | PECAN |
| AK | PINE |
| BE | PINE, EASTERN WHITE |
| HP | PINE, HOOP |
| BL | PINE, IDAHO WHITE |
| BM | PINE, JACK |
| BQ | PINE, LODGEPOLE |
| FJ | PINE, NORWAY |
| FG | PINE, PITCH |
| CB | PINE, PONDEROSA |
| CQ | PINE, SOUTHERN |
| CT | PINE, SUGAR |
| CD | POPLAR |
| DK | POPLAR, YELLOW |
| AL | REDWOOD |
| HS | SAPELLI |
| HR | SIPO |
| DL | SOFTWOOD |
| CS | SPRUCE |
| FK | SPRUCE, EASTERN |
| BG | SPRUCE, ENGELMANN |
| CN | SPRUCE, SITKA |
| FL | SPRUCE, WESTERN WHITE |
| FX | SPRUCE-PINE-FIR |
| FM | SYCAMORE, AMERICAN |
| FN | TAMARACK |
| FH | TUPELO |
| AG | WALNUT |
| AZ | WALNUT, BLACK |
| FP | WILLOW |
| FQ | WILLOW, BLACK |
| Table 2 |
| Reply Code (AP63) | Reply |
| AB | 2-4-1 |
| BN | A/I |
| AC | A-A INTERIOR |
| AD | A-A MARINE EXTERIOR |
| AE | A-A MARINE EXTERIOR MDO |
| AF | A-B EXTERIOR |
| AG | A-B INTERIOR |
| AH | A-C EXTERIOR |
| AK | A-D INTERIOR |
| AQ | BACKING-4 |
| AL | B-B CONCRETE FORM |
| AM | B-B EXTERIOR HDO |
| AN | B-C EXTERIOR |
| AP | B-D INTERIOR |
| AS | C-C EXTERIOR |
| AJ | C-C PLUGGED EXTERIOR |
| AT | C-D EXTERIOR-CDX |
| AW | C-D INTERIOR |
| AR | CONTAINER GRADE |
| BQ | EXTERIOR CTB X |
| AX | GOOD-1 |
| BR | II/II |
| BP | II/III |
| AY | PREMIUM-A |
| AZ | SOUND-2 |
| BA | SPECIALTY-SP |
| BC | STRUCTURAL II |
| BB | STRUCUTRAL I |
| BD | UNDERLAYMENT |
| BE | UTILITY-3 |
IF STYLE/REPLY CODE(s) RN WERE ENTERED FOR MRC CSHP, YOU MUST ANSWER MRC (CSHB)
CSHPJTHICKNESS-LOCATION AND MEASURING METHOD
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED.
Enter the applicable Reply Code from Tables 1 & 2 & 3 & 4 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSHPJACBEDRN2.0*;CSHPJACBEDRN2.0$$JACBEDRN2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN73) | Reply |
| BED | BUTT END |
| AAD | OVERALL |
| TED | TAPERED END |
| Table 4 |
| Reply Code (AN68) | Reply |
| RN | RANDOM |
| SD | SPECIFIED |
CSHB*GRANDOM THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter clear text.
(CSHBGCLEARTEXT)
IF STYLE/REPLY CODE(s) RN WERE ENTERED FOR MRC CRPW, YOU MUST ANSWER MRC (CQKJ)
CRPWJWIDTH-LOCATION AND MEASURING METHOD
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS,ITS LOCATION ON THE ITEM,AND THE MEASURING METHOD USED. PLEASE USE MRC CRXX WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 & 4 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRPWJABTEDSD2.0*;CRPWJABTEDSD2.0$$JABTEDSD2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN73) | Reply |
| BED | BUTT END |
| AAD | OVERALL |
| TED | TAPERED END |
| Table 4 |
| Reply Code (AN68) | Reply |
| RN | RANDOM |
| SD | SPECIFIED |
CQKJ*GRANDOM WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter clear text.
(CQKJGCLEARTEXT)
IF STYLE/REPLY CODE(s) RN WERE ENTERED FOR MRC CRXX, YOU MUST ANSWER MRC (CRJD)
CRXXJMEASURING METHOD AND LENGTH
THE MEANS USED AND THE MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRXXJFCRN2.0*;CRXXJFCRN2.0$$JFCRN2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AN68) | Reply |
| RN | RANDOM |
| SD | SPECIFIED |
CRJD*GRANDOM LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.
Enter clear text.
(CRJDGCLEARTEXT)
CQHF*DMAXIMUM GRAIN SLOPE
INDICATES THE MAXMIUM SLOPE OF GRAIN IN RELATION TO THE LENGTH OF THE ITEM.
Enter the applicable reply code from the table below
(CQHFDAM)
| Table 1 |
| Reply Code (AP05) | Reply |
| AH | 1 IN 10 |
| AJ | 1 IN 11 |
| AK | 1 IN 12 |
| AL | 1 IN 13 |
| AM | 1 IN 14 |
| AN | 1 IN 15 |
| AP | 1 IN 16 |
| AQ | 1 IN 17 |
| AR | 1 IN 18 |
| AS | 1 IN 19 |
| AT | 1 IN 20 |
| AW | 1 IN 21 |
| AX | 1 IN 22 |
| AY | 1 IN 23 |
| AZ | 1 IN 24 |
| BA | 1 IN 25 |
| BB | 1 IN 26 |
| BC | 1 IN 27 |
| BD | 1 IN 28 |
| BE | 1 IN 29 |
| BF | 1 IN 30 |
| AB | 1 IN 4 |
| AC | 1 IN 5 |
| AD | 1 IN 6 |
| AE | 1 IN 7 |
| AF | 1 IN 8 |
| AG | 1 IN 9 |
CRDRDGLUE TYPE
INDICATES THE TYPE OF GLUE USED TO FABRICATE THE ITEM.
Enter the applicable reply code from the table below
(CRDRDAAE*;CRDRDT$DAAD*)
| Table 1 |
| Reply Code (AN74) | Reply |
| E | EXTERIOR |
| F | INTERIOR |
| AAB | NF B54-160 TYPE I |
| AAC | NF B54-160 TYPE II |
| AAD | NF B54-160 TYPE III |
| AAE | NF B54-160 TYPE IV |
| S | TECHNICAL-EXTERIOR |
| T | TYPE I-EXTERIOR |
| Y | TYPE III-INTERIOR |
| W | TYPE II-INTERIOR |
CQGP*HOVERLAY DENSITY AND LOCATION
THE DENSITY OF THE SURFACING MATERIAL AND ITS LOCATION ON THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CQGPHAJBSD*)
| Table 1 |
| Reply Code (AG49) | Reply |
| AG | HIGH |
| AJ | MEDIUM |
| Table 2 |
| Reply Code (AN73) | Reply |
| BSD | BOTH SIDES |
| WSE | ONE SIDE |
IF STYLE/REPLY CODE(s) ABEQ OR ABER WERE ENTERED FOR MRC CSJL, YOU MUST ANSWER MRC (CRNJ)
CSJL*DCORE MATERIAL TYPE
INDICATES THE TYPE OF MATERIAL COMPOSING THE CORE.
Enter the applicable reply code from the table below
(CSJLDABEP*;CSJLDABES$DABEN*)
| Table 1 |
| Reply Code (AN48) | Reply |
| ABET | HARDBOARD |
| ABEQ | HARDWOOD LUMBER |
| ABEN | HARDWOOD VENEER |
| ABES | PARTICLEBOARD |
| ABER | SOFTWOOD LUMBER |
| ABEP | SOFTWOOD VENEER |
CRNJ*DCORE GRADE
AN INDICATION OF THE GRADE OF THE CORE.
Enter the applicable reply code from the table below
(CRNJDDC*;CRNJDHG$DHF*)
| Table 1 |
| Reply Code (AP02) | Reply |
| DC | CLEAR |
| HG | CLEAR EDGE |
| HF | REGULAR |
| HE | SOUND |
CRYQ*DSURFACE CONDITION DEGREE
THE EXTENT OF SURFACE DRESSING OR ROUGHNESS OF THE ITEM.
Enter the applicable reply code from the table below
(CRYQDAC*;CRYQDAG$DAF*)
| Table 1 |
| Reply Code (AP06) | Reply |
| AC | CLEAN PEELED FULL LENGTH |
| BD | DROP SIDING PATTERN 105 FULL LENGTH |
| AB | DROP SIDING PATTERN 106 FULL LENGTH |
| AD | POLISH SANDED ONE SIDE |
| AE | POLISH SANDED TWO SIDES |
| AF | REGULAR SANDED ONE SIDE |
| AG | REGULAR SANDED TWO SIDES |
| AJ | ROUGH PEELED FULL LENGTH |
| AK | ROUGH SANDED ONE SIDE |
| AL | ROUGH SANDED TWO SIDES |
| AH | ROUGH-UNSANDED FULL LENGTH |
| AM | SMOOTH SURFACE AND PREFINISHED FULL LENGTH |
| AN | SMOOTH SURFACE WITHOUT FINISH FULL LENGTH |
| BA | SURFACED FOUR SIDES |
| BB | SURFACED FOUR SIDES AND CAULKING SEAM |
| AP | SURFACED ONE EDGE |
| AQ | SURFACED ONE SIDE |
| AR | SURFACED ONE SIDE AND ONE EDGE |
| AS | SURFACED ONE SIDE AND TWO EDGES |
| AT | SURFACED TWO EDGES |
| BE | SURFACED TWO SIDES |
| AX | SURFACED TWO SIDES AND CENTER MATCHED |
| BF | SURFACED TWO SIDES AND ONE EDGE |
| AY | SURFACED TWO SIDES AND SHIPLAP |
| AZ | SURFACED TWO SIDES AND STANDARD MATCHED |
| AW | SURFACED TWO SIDES, ONE EDGE AND NOSED ONE EDGE |
| BC | UNPEELED FULL LENGTH |
IF STYLE/REPLY CODE(s) EQ WERE ENTERED FOR MRC BMKY, YOU MUST ANSWER MRC (CQMP)
IF STYLE/REPLY CODE(s) ER OR HD WERE ENTERED FOR MRC BMKY, YOU MUST ANSWER MRC (CQMP and CSTZ)
BMKY*DTREATMENT TYPE
INDICATES THE TYPE OF TREATMENT PROVIDED.
Enter the applicable reply code from the table below
(BMKYDEN)
| Table 1 |
| Reply Code (AK89) | Reply |
| DB | FIRE RETARDANT |
| EN | FIRE RETARDANT, MIL-L-19140 |
| HF | FUNGICIDAL |
| HG | INSERT REPELLANT |
| DF | MARINE BORER RESISTANT |
| EQ | PRESERVATIVE, MIL-C-12436 |
| EP | PRESERVATIVE, MIL-P-19550 |
| ER | PRESERVATIVE, TT-W-571 |
| HD | PRESERVATIVE, TT-W-572 |
| DQ | WATER REPELLENT |
CQMP*DPRESERVATIVE SOLUTION TYPE
INDICATES THE TYPE OF SOLUTION USED TO PRESERVE THE ITEM.
Enter the applicable reply code from the table below
(CQMPDFD*;CQMPDHA$DGZ*)
| Table 1 |
| Reply Code (AK89) | Reply |
| EY | ACID COPPER CHROMATE |
| EZ | AMMONIACAL COPPER ARSENITE |
| GS | CHROMATED COPPER ARSENATE, TYPE I, II OR III |
| FD | CHROMATED ZINC CHLORIDE |
| CM | COAL-TAR CREOSOTE |
| HA | COPPER NAPHTHENATE |
| HB | COPPER NAPHTHENATE HIGH CONCENTRATION |
| GZ | COPPER-8-QUINOLINOLATE |
| CS | CREOSOTE COAL-TAR SOLUTION |
| CX | CREOSOTE PETROLEUM SOLUTION |
| HC | CREOSOTE/PENTACHLOROPHENOL |
| GT | DUAL TREATMENT |
| GW | FLUOR-CHROME-ARSENATE-PHENOL, TYPE I OR TYPE II |
| DH | PENTACHLOROPHENOL |
| FH | PENTACHLOROPHENOL IN HEAVY PETROLEUM SOLVENT |
| FJ | PENTACHLOROPHENOL IN LIGHT PETROLEUM SOLVENT |
| GX | PENTACHLOROPHENOL IN VOLATILE SOLVENT |
| GY | TRIBUTYLTIN OXIDE |
CSTZ*DSERVICE USAGE
THE APPLICATION FOR WHICH THE ITEM IS INTENDED.
Enter the applicable reply code from the table below
(CSTZDAL*;CSTZDAY$DAB*;CSTZDAY$$DAB*)
| Table 1 |
| Reply Code (AN66) | Reply |
| AB | BUILDING |
| AQ | BUILDING FOUNDATION |
| AC | CONTACT W/GROUND |
| AD | FENCE |
| BB | FOR USE ABOVE GROUND |
| BA | IMPORTANT STRUCTURAL MEMBERS IN CONTACT WITH GROUND OR FRESH WATER |
| AE | IMPORTANT STRUCTURAL MEMBERS NOT IN CONTACT W/GROUND OR WATER |
| AF | IN COASTAL WATERS |
| AR | IN CONTACT WITH OR CLOSE PROXIMITY TO FOODSTUFF |
| AG | IN FRESH WATER |
| AS | LUMBER |
| AT | PILES |
| AW | POLES |
| AX | POSTS |
| AY | READY-TO-USE SOLUTIONS BY SIMPLE NONPRESSURE METHODS |
| AL | TIES |
| AZ | TIMBERS |
| AN | UTILITY |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| ML | MATERIAL |
| MH | MESH |
| ME | METHOD |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAE*;BBRGDAM$DAC*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| BD | OPEN STORAGE |
| AJ | UNHEATED WAREHOUSE |
BBRH*JINSPECTION FREQUENCY
THE SPECIFIED TIME INTERVAL,FROM RECEIPT,NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit.
(BBRHJDYAC2*;BBRHJDYAC2$$JDYAC3*)
| Table 1 |
| Reply Code (AH68) | Reply |
| DY | DAYS |
| MH | MONTHS |
| Table 2 |
| Reply Code (AM82) | Reply |
| AB | FIRST INSPECTION |
| AC | REINSPECTION |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CQCT*DPRIMARY CONTAINER TYPE
INDICATES THE TYPE OF CONTAINER/S/ OR SUPPORTING DEVICE/S/ WHICH IS IN DIRECT CONTACT WITH THE ITEM.
Enter the applicable reply code from the table below
(CQCTDA)
| Table 1 |
| Reply Code (AN65) | Reply |
| A | ANY ACCEPTABLE |
| ACD | BOX |
| AFA | CRATE |
| AFB | SKID |
CRLK*JPRIMARY CONTAINER CONTENT QUANTITY
A NUMERIC VALUE OF THE VOLUME,FORM,OR DOSAGE WITHIN EACH PRIMARY CONTAINER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRLKJSH2.0*)
| Table 1 |
| Reply Code (AN64) | Reply |
| EA | EACH |
| SH | SHEET |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information