An item consisting of two definite lengths of insulated electrical cable having each end terminated with a CLIP (1), ELECTRICAL. The cables and/or clips are color coded for identification. The item provides for the quick temporary transfer of electrical energy for restarting a disabled vehicle engine. The conductors may be twisted or molded together (except at the ends) or entirely separated. Excludes:items having branches or forks. Excludes:LEAD, TEST; CABLE ASSEMBLY, SPECIAL PURPOSE, ELECTRICAL and LEAD, ELECTRICAL.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED36364*)
ACVLJCONDUCTOR SIZE
THE WIRE GAGE DESIGNATION AND THE GAGE NUMBER USED TO DESCRIBE THE CONDUCTOR SIZE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ACVLJJ2*;ACVLJJ2$$JJ3*)
| Table 1 |
| Reply Code (AB96) | Reply |
| B | AWG |
| J | SQUARE MILLIMETERS |
| C | SWG |
CYGJDCOVERING MATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE COVERING IS FABRICATED.
Enter the applicable reply code from the table below
(CYGJDRCB000*;CYGJDPCX000$DPCA000*;CYGJDPCX000$$DPCA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| PCA000 | PLASTIC |
| PCCB00 | PLASTIC NYLON |
| PCP000 | PLASTIC POLYAMIDE |
| PCX000 | PLASTIC POLYETHYLENE |
| PCCD00 | PLASTIC POLYVINYL |
| RCE000 | RUBBER |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RCB000 | RUBBER SYNTHETIC |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJFB2.0*;ABHPJFB2.0$$JFB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMEMDBINDING METHOD
THE MEANS BY WHICH THE ITEM IS BOUND.
Enter the applicable reply code from the table below
(AMEMDBF*;AMEMDAC$DCC*;AMEMDAC$$DCC*)
| Table 1 |
| Reply Code (AJ03) | Reply |
| AQ | ENCLOSED IN PLASTIC SHIELD |
| CB | MOLDED |
| BF | NEOPRENE COVERED |
| BS | TAPED |
| AC | TIED |
| BX | WIRE BOUND |
| CC | YOKE |
CYGKJCLAMP CURRENT RATING
THE AMOUNT OF CURRENT FOR WHICH THE CLAMPS ARE RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CYGKJL2.0*)
| Table 1 |
| Reply Code (AC30) | Reply |
| A | AMPERES |
| L | MILLIAMPERES |
AHGQDCLAMP TYPE
INDICATES THE TYPE OF CLAMP PROVIDED.
Enter the applicable reply code from the table below
(AHGQDAT*;AHGQDAW$DAD*;AHGQDAW$$DAD*)
| Table 1 |
| Reply Code (AF32) | Reply |
| AD | EXTRA HEAVY |
| AC | HEAVY |
| AT | HINGED JAW |
| AW | LIGHT DUTY |
| AX | PARROT JAW |
| AB | STANDARD |
CYGLDCLAMP INSULATION COLOR
THE HUE OR TINT OF THE INSULATION ON THE CLAMP.
Enter the applicable reply code from the table below
(CYGLDBU0000*;CYGLDGR0000$$DWH0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| BU0000 | BLUE |
| GR0000 | GREEN |
| RE0000 | RED |
| WH0000 | WHITE |
| YE0000 | YELLOW |
AWTN*JOPERATING TEMP RATING
THE TEMPERATURE AT WHICH THE ITEM OPERATES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWTNJCA2.0*;AWTNJCA2.0$$JCA2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASXH*JVOLTAGE RATING IN VOLTS
THE VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASXHJBB2.0*;ASXHJBB2.0$$JBB2.1*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| C | DC |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDDUL*;CBBLDCMA$$DAAK*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AAK | ELECTROSTATIC DISCHARGE CAPABILITY |
| DUK | EXTERNAL MOUNT STARTING RECEPTACLE |
| CMA | ILLUMINATED |
| CSD | MOUNTING ATTACHMENT |
| AHJ | NONSPARKING |
| DUM | PARALLEL CONSTRUCTION |
| DUL | SIAMESE CONSTRUCTION |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| ML | MATERIAL |
| MH | MESH |
| ME | METHOD |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information