An insulated upright cabinet/enclosure with two separate storage compartments, fresh food section and frozen food section. It may have the capability of producing ice cubes automatically. It is intended for storage and preservation of both fresh and frozen foods. The freezer compartment may also be used for freezing perishable food rapidly. Excludes:DISPLAY CASE, MECHANICALLY REFRIGERATED; FREEZER, MECHANICAL, FOOD; REFRIGERATION UNIT, MECHANICAL; REFRIGERATOR, MECHANICAL, FOOD; REFRIGERATOR, PREFABRICATED.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED35635*)
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
HUESDCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDWA0004*;HUESDWH0000$DA*;HUESDWH0000$$DA*)
| Table 1 |
| Reply Code (AD06) | Reply |
| A | ANY ACCEPTABLE |
| BL0000 | BLACK |
| BR0023 | BROWN, WOOD |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| SL0000 | SILVER |
| WA0004 | WALNUT, GRAIN |
| WH0000 | WHITE |
BBDYJCAPACITY AND LOCATION
A MEASUREMENT OF THE CAPACITY OF AN ITEM AND ITS LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBDYJLDAAZH2.0*;BBDYJLDAAZH2.0$$JLDAAZH2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| CY | CUBIC FEET |
| LD | CUBIC METERS |
| DQ | SQUARE FEET |
| EL | SQUARE METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| AXA | CABINET |
| AZG | DISPLAY SHELF AREA |
| EAA | FROZEN FOOD STORAGE |
| BLE | REFRIGERATED STORAGE |
| AZH | STORAGE |
APQBDUNIT TYPE
INDICATES THE TYPE OF UNIT.
Enter the applicable reply code from the table below
(APQBDAPH*;APQBDAPL$DADS*;APQBDAPL$$DADS*)
| Table 1 |
| Reply Code (AK95) | Reply |
| A | ANY ACCEPTABLE |
| APF | CHEST |
| AME | DISPENSING |
| APG | DRY COLD CABINET |
| CAZ | FULL VISION, COUNTER AND SHELVES, CAFETERIA SERVICE |
| APH | FULL-VISION, CLERK-SERVICE, DISPLAY |
| APJ | FULL-VISION, SELF-SERVICE, DISPLAY |
| AMF | HARDENING |
| APK | OPEN COLD |
| APL | OPEN COLD SELF-SERVICE |
| ADL | OPEN COLD SELF-SERVICE MULTIPLE DISPLAY |
| ADM | PASS THRU |
| ADN | PORTABLE CHEST |
| ADP | PORTABLE REACH-IN |
| ADQ | PORTABLE WALK-IN |
| ADR | PREFABRICATED SECTIONAL REACH-IN-WALK-IN |
| ADS | PREFABRICATED SECTIONAL WALK-IN |
| ADT | REACH-IN |
| ADW | SELF-SERVICE CHEST |
| AJS | UPRIGHT |
| ADX | UPRIGHT CABIN |
| ADY | WALK-IN |
ATSZADOOR QUANTITY
THE NUMBER OF DOORS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ATSZA10*)
AYTCDHINGE LOCATION
INDICATES THE LOCATION OF THE HINGE/S/ ON THE ITEM.
Enter the applicable reply code from the table below
(AYTCDAHP*;AYTCDAVW$DACF*;AYTCDAVW$$DACF*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| A | ANY ACCEPTABLE |
| AHP | CENTER |
| ACF | LEFT SIDE |
| ABJ | REAR |
| AVW | REVERSIBLE |
| ACR | RIGHT SIDE |
AYTEJFROZEN FOOD COMPARTMENT OPERATING TEMP RANGE
THE MINIMUM AND MAXIMUM LIMITS OF OPERATING TEMPERATURE AT WHICH THE FROZEN FOOD COMPARTMENT IS RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AYTEJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AYTFJCABINET OPERATING TEMP RANGE
THE MINIMUM AND MAXIMUM LIMITS OF OPERATING TEMPERATURE AT WHICH THE CABINET IS RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AYTFJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
AYTGDVEGETABLE BIN
AN INDICATION OF WHETHER OR NOT A VEGETABLE BIN IS INCLUDED.
Enter the applicable reply code from the table below
(AYTGDB*;AYTGDC$DC*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) HH WERE ENTERED FOR MRC APHE, YOU MUST ANSWER MRC (AYTH)
APHEDOPERATION METHOD
THE MEANS USED TO OPERATE THE ITEM.
Enter the applicable reply code from the table below
(APHEDHJ*;APHEDA$DHH*)
| Table 1 |
| Reply Code (AC58) | Reply |
| HH | ABSORPTION |
| A | ANY ACCEPTABLE |
| HJ | COMPRESSION |
ALBYDUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDBRG*;ALBYDAGL$DBRF*)
| Table 1 |
| Reply Code (AH21) | Reply |
| AAE | COMMERCIAL |
| BRF | DEPO LEVEL OVERHAUL |
| AAD | DOMESTIC |
| BRG | GYROSCOPE ASSEMBLY REPAIR |
| AGL | TROPICAL SERVICE |
AHZXBPRIME MOVER HORSEPOWER RATING
THE RATED HORSEPOWER OF THE PRIME MOVER.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AHZXB2.0)
AZAADEVAPORATOR
AN INDICATION OF WHETHER OR NOT AN EVAPORATOR IS INCLUDED.
Enter the applicable reply code from the table below
(AZAADC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AZBADICE CUBE MAKING EQUIPMENT
AN INDICATION OF WHETHER OR NOT ICE CUBE MAKING EQUIPMENT IS INCLUDED.
Enter the applicable reply code from the table below
(AZBADB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDCLD000*;SFTTDCLC000$DENA000*;SFTTDCLC000$$DENA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ENA000 | ENAMEL |
| CLD000 | ENAMEL PORCELAIN |
| CLC000 | PORCELAIN |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAA2.0*;ABFYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBMK*JFROZEN FOOD COMPARTMENT CAPACITY
THE CAPACITY OF THE COMPARTMENT FOR FROZEN FOOD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBMKJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
AYTH*DHEAT GENERATING METHOD
THE MEANS BY WHICH THE HEAT IS GENERATED.
Enter the applicable reply code from the table below
(AYTHDAD*;AYTHDAE$DAJ*)
| Table 1 |
| Reply Code (AM63) | Reply |
| AJ | ELECTRICITY |
| AC | KEROSENE |
| BQ | LIQUID PETROLEUM GAS |
| AD | MANUFACTURED GAS |
| AE | NATURAL GAS |
AWLP*DCONDENSER TYPE
INDICATES THE TYPE OF CONDENSER.
Enter the applicable reply code from the table below
(AWLPDAW*;AWLPDAJ$DA*)
| Table 1 |
| Reply Code (AM41) | Reply |
| A | ANY ACCEPTABLE |
| AH | HERMETICALLY SEALED |
| AT | MECHANICALLY SEALED |
| AJ | OPEN |
| AM | SEMIHERMETICALLY SEALED |
| AK | SEMI-INCLOSED |
| AW | THERMALLY SEALED |
AZAD*DCONDENSER COOLING TYPE
INDICATES THE TYPE OF COOLING FOR WHICH THE CONDENSER IS DESIGNED.
Enter the applicable reply code from the table below
(AZADDSK*;AZADDDF$DAB*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AB | AIR |
| SK | EVAPORATIVE |
| DF | WATER |
AWCD*DWATER FOR WHICH DESIGNED
THE TYPE OF WATER WITH WHICH THE ITEM IS DESIGNED TO BE USED.
Enter the applicable reply code from the table below
(AWCDDA)
| Table 1 |
| Reply Code (AB75) | Reply |
| A | ANY ACCEPTABLE |
| KR | FRESH |
| KS | SALT |
AZAQ*DCONDENSER UNIT LOCATION
INDICATES THE LOCATION OF THE CONDENSER UNIT.
Enter the applicable reply code from the table below
(AZAQDAKN*;AZAQDAXA$DAKP*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| AXH | AFFIXED |
| AXA | CABINET |
| AKN | INTEGRAL |
| AKP | REMOTE |
AZAE*ACONDENSER UNIT QUANTITY
THE NUMBER OF CONDENSER UNITS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AZAEA10*)
ACDC*DCURRENT TYPE
INDICATES THE TYPE OF CURRENT WHETHER ALTERNATING,DIRECT,OR BOTH.
Enter the applicable reply code from the table below
(ACDCDB*;ACDCDD$DC*)
| Table 1 |
| Reply Code (AB62) | Reply |
| B | AC |
| D | AC/DC |
| C | DC |
AMSE*JVOLTAGE RATING
THE VALUE(S) OF POTENTIAL FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMSEJKB2.0*;AMSEJKB2.0$$JKB2.1*)
| Table 1 |
| Reply Code (AB63) | Reply |
| K | KILOVOLTS |
| V | VOLTS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACZB*JFREQUENCY RATING
THE NUMBER OF COMPLETE CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH AN ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACZBJEB2.0*;ACZBJEB2.0$$JEB2.1*)
| Table 1 |
| Reply Code (AC32) | Reply |
| E | HERTZ |
| K | KILOHERTZ |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDA*;FAAZDB$DE*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| E | SINGLE/THREE |
| C | THREE |
| B | TWO |
ARAG*JCURRENT RATING
THE AMOUNT OF CURRENT FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARAGJL2.0*)
| Table 1 |
| Reply Code (AC30) | Reply |
| A | AMPERES |
| U | MICROAMPERES |
| L | MILLIAMPERES |
AZEA*DEVAPORATOR UNIT TYPE
INDICATES THE TYPE OF EVAPORATOR UNIT.
Enter the applicable reply code from the table below
(AZEADAEB*;AZEADAEC$DAEC*)
| Table 1 |
| Reply Code (AK95) | Reply |
| AEB | FORCED AIR-COOLING |
| AEC | GRAVITY CONVECTION |
AZAC*BFAN MOTOR HORSEPOWER RATING
THE RATED HORSEPOWER OF THE FAN MOTOR.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AZACB2.0)
ACYN*JAC VOLTAGE RATING
THE VALUE,OR RANGE OF VALUES,OF ROOT MEAN SQUARE POTENTIAL FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYNJKC2.0*;ACYNJKC2.0$$JKC2.1*)
| Table 1 |
| Reply Code (AB63) | Reply |
| K | KILOVOLTS |
| V | VOLTS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APNB*JAC FREQUENCY RATING
THE NUMBER OF COMPLETE ALTERNATING CURRENT CYCLIC CHANGES,PER UNIT OF TIME,FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APNBJEB2.0*;APNBJEB2.0$$JEB2.1*)
| Table 1 |
| Reply Code (AC32) | Reply |
| E | HERTZ |
| K | KILOHERTZ |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANSA*DWINDING PHASE
THE NUMBER OF ALTERNATING CURRENT WINDING PHASE(S).
Enter the applicable reply code from the table below
(ANSADC*;ANSADB$DD*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| D | SINGLE OR THREE |
| C | THREE |
| B | TWO |
ACYR*JDC VOLTAGE RATING
THE VALUE,OR RANGE OF VALUES,OF DIRECT CURRENT POTENTIAL FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYRJVA2.0*;ACYRJVA2.0$$JVA2.1*)
| Table 1 |
| Reply Code (AB63) | Reply |
| K | KILOVOLTS |
| V | VOLTS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMPS*BCURRENT RATING IN AMPS
THE ELECTRICAL CURRENT RATING,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AMPSB2.0)
AKYD*GACCESSORY COMPONENTS AND QUANTITY
THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.
Enter clear text.
(AKYDGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDLK*;ENACDNR$$DFU*)
| Table 1 |
| Reply Code (EN02) | Reply |
| FU | REFRIGERATORS AND FREEZERS, COMMERCIAL - ENERGY STAR-COMMERCIAL FOOD SERVICE EQUIPMENT - ENERGY EFFICIENT PRODUCTS |
| LK | REFRIGERATORS AND FREEZERS, RESIDENTIAL - ENERGY STAR-APPLICANCES - ENERGY EFFICIENT PRODUCTS |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAE5)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAI7)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ072*;HZRDDHAZ031$$DHAZ064*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ010 | CARBON DIOXIDE |
| HAZ031 | METHYL CHLORIDE |
| HAZ070 | REFRIGERANT GAS, R 114 |
| HAZ066 | REFRIGERANT GAS, R 115 |
| HAZ078 | REFRIGERANT GAS, R 116 |
| HAZ072 | REFRIGERANT GAS, R 12 |
| HAZ068 | REFRIGERANT GAS, R 13 |
| HAZ082 | REFRIGERANT GAS, R 14 |
| HAZ076 | REFRIGERANT GAS, R 21 |
| HAZ062 | REFRIGERANT GAS, R 22 |
| HAZ074 | REFRIGERANT GAS, R 500 |
| HAZ064 | REFRIGERANT GAS, R 502 |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDSTB000*;MATT3AEEDSTB000$DALB000*;MATT3AEEDSTB000$$DALB000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HUG | OUTSIDE SHELL |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| FG0000 | FIBERGLASS |
| PCA000 | PLASTIC |
| CLB000 | PORCELAIN |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
AWZJ*DPOWER SOURCE
THE SOURCE OF POWER WHICH PROVIDES THE ENERGY REQUIRED FOR THE OPERATION OF THE ITEM.
Enter the applicable reply code from the table below
(AWZJDAD)
| Table 1 |
| Reply Code (AG27) | Reply |
| AD | ELECTRIC MOTOR |
| BT | ELECTRICITY |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information