A bent hollow item, welded or seamless. It has a round, square or any other cross section, with a continuous periphery. It is primarily designed to convey fluids, gases and/or semisolids. Excludes:items of circular cross section which conform in dimensional characteristics to PIPE, METALLIC; ELBOW, PIPE; ELBOW, TUBE; BEND, ELECTRICAL CONDUIT; BEND, PIPE, RETURN; and BEND, TUBE, RETURN. For items with end fittings on one or both ends, see TUBE ASSEMBLY, METAL.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED32507*)
IF STYLE/REPLY CODE(s) 3 OR 16 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHB)
IF STYLE/REPLY CODE(s) 6 OR 17 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAJA and AAHC)
IF STYLE/REPLY CODE(s) 7 OR 8 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (CQYM and CQKK and ATKT)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHD)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHF)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHB and AAHE)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHA and AAHB and AAHE)
IF STYLE/REPLY CODE(s) 13 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHG and AAHH and AAHJ)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHB and AAHD and AAHM and AAHK)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC AAGZ, YOU MUST ANSWER MRC (AAHB and AAHL)
AAGZLFIRST END STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FIRST END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAGZL14)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAB1037 | 1 | PLAIN |
| AAB1044 | 10 | FLANGE |
| AAB1045 | 11 | SINGLE FLARE |
| AAB1046 | 12 | DOUBLE FLARE |
| AAB1047 | 13 | OUTSIDE GROOVED |
| AAB1048 | 14 | OUTSIDE BEADED |
| AAB1049 | 15 | OUTSIDE UNDERCUT |
| AAB1050 | 16 | SWELLED OR STRETCHED DIAMETER |
| AAB1051 | 17 | HUB |
| AAB1038 | 2 | BEVELED |
| AAB1039 | 3 | OUTSIDE UPSET |
| AAB1040 | 6 | BELL |
| AAB1041 | 7 | THREADED EXTERNAL |
| AAB1042 | 8 | THREADED INTERNAL |
| AAB1043 | 9 | SPIGOT |
IF STYLE/REPLY CODE(s) M WERE ENTERED FOR MRC CQBB, YOU MUST ANSWER MRC (AAHP)
CQBBDSECOND END RELATIONSHIP WITH FIRST END
INDICATES WHETHER OR NOT THE SECOND END IS IDENTICAL TO THE FIRST END.
Enter the applicable reply code from the table below
(CQBBDP)
| Table 1 |
| Reply Code (AN69) | Reply |
| P | IDENTICAL |
| M | NOT IDENTICAL |
IF STYLE/REPLY CODE(s) HS OR SS WERE ENTERED FOR MRC CQCF, YOU MUST ANSWER MRC (AAJH)
CQCFDCONSTRUCTION
THE STRUCTURAL CHARACTERISTIC OF THE ITEM.
Enter the applicable reply code from the table below
(CQCFDSS*;CQCFDAA$DHS*)
| Table 1 |
| Reply Code (AN70) | Reply |
| AA | ANNEALED |
| FA | FULLY FURNISHED |
| HS | HELICAL SEAMED |
| SL | SEAMLESS |
| SS | STRAIGHT SEAMED |
CQGMJMAXIMUM OPERATING PRESSURE
THE MAXIMUM PRESSURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQGMJP2.0*)
| Table 1 |
| Reply Code (AN71) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| L | KILOPASCALS |
| N | NEWTONS PER SQUARE CENTIMETER |
| P | POUNDS PER SQUARE INCH |
AEHZJMAXIMUM OPERATING TEMP
THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS RATED TO OPERATE FOR AN EXTENDED PERIOD OF TIME.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHZJF2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
IF STYLE/REPLY CODE(s) 1 OR 3 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (AAGT and ABMZ)
IF STYLE/REPLY CODE(s) 11, 14, 16, 19, 20 OR 21 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (AAGT and ABGL and HGTH)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (AAGT and ASDB)
AAGRLCROSS-SECTIONAL SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAGRL11)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAB1028 | 1 | PLAIN ROUND |
| AAB1030 | 11 | OVAL |
| AAB1031 | 14 | SQUARE/RECTANGULAR |
| AAB1032 | 16 | SQUARE/RECTANGULAR |
| AAB1033 | 17 | HEXAGON INTERIOR ROUND |
| AAB1034 | 19 | EGG SHAPED |
| AAB1035 | 20 | OBLONG |
| AAB1036 | 21 | D-SHAPED |
| AAB1029 | 3 | ROUND, INTERIOR OCTAGON |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDCU0330*;MATTDST0050$DST0303*;MATTDST0050$$DST0303*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL3003 | ALUMINUM ALLOY 3003 |
| AL5050 | ALUMINUM ALLOY 5050 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5056 | ALUMINUM ALLOY 5056 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL5454 | ALUMINUM ALLOY 5454 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6063 | ALUMINUM ALLOY 6063 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0247 | COPPER ALLOY 120 |
| CU0330 | COPPER ALLOY 330 |
| CU0117 | COPPER ALLOY 62 |
| CU0706 | COPPER ALLOY 706 |
| CU0715 | COPPER ALLOY 715 |
| CU0180 | COPPER ALLOY 857 |
| CU0182 | COPPER ALLOY 862 |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| PBA000 | LEAD |
| PBB000 | LEAD ALLOY |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| PCA000 | PLASTIC |
| STA000 | STEEL |
| ST1010 | STEEL COMP 1010 |
| ST1015 | STEEL COMP 1015 |
| ST1020 | STEEL COMP 1020 |
| ST1022 | STEEL COMP 1022 |
| ST1025 | STEEL COMP 1025 |
| ST1026 | STEEL COMP 1026 |
| ST1030 | STEEL COMP 1030 |
| ST1045 | STEEL COMP 1045 |
| ST1050 | STEEL COMP 1050 |
| ST1118 | STEEL COMP 1118 |
| ST1137 | STEEL COMP 1137 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0268 | STEEL COMP 30321 |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0305 | STEEL COMP 305 |
| ST0309 | STEEL COMP 309 |
| ST0310 | STEEL COMP 310 |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0321 | STEEL COMP 321 |
| ST0347 | STEEL COMP 347 |
| ST0348 | STEEL COMP 348 |
| ST0403 | STEEL COMP 403 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST4135 | STEEL COMP 4135 |
| ST0414 | STEEL COMP 414 |
| ST4140 | STEEL COMP 4140 |
| ST0416 | STEEL COMP 416 |
| ST4617 | STEEL COMP 4617 |
| ST0138 | STEEL COMP 8622H |
| ST8630 | STEEL COMP 8630 |
| ST0139 | STEEL COMP 8630H |
| ST8640 | STEEL COMP 8640 |
| ST8735 | STEEL COMP 8735 |
| ST0046 | STEEL COMP MT1010 |
| ST0047 | STEEL COMP MT1015 |
| ST0048 | STEEL COMP MT1020 |
| ST0049 | STEEL COMP MTX1015 |
| ST0050 | STEEL COMP MTX1020 |
| ST0702 | STEEL COMP XM-10 |
| STB000 | STEEL CORROSION RESISTING |
| STC000 | STEEL STAINLESS - USE STB000 |
| SNB000 | TIN |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TT0040 | TITANIUM UNS R50400 |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AUWDXXA000*;SFTT3AUWDXXA000$DCDA000*;SFTT3AUWDXXA000$$DCDA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AUC | INSIDE |
| 3AUW | OUTSIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ALA000 | ALUMINUM ALLOY |
| ANA000 | ANODIZE |
| CPB000 | ASPHALT |
| CDA000 | CADMIUM |
| AAA013 | CARC (CHEMICAL AGENT RESISTANT COATING), ALIPHATIC POLYURETHANE |
| MSE000 | CEMENT |
| CMA000 | CHROMATE |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| ENA000 | ENAMEL |
| END000 | ENAMEL BAKED |
| AUA000 | GOLD |
| GFA000 | GRAPHITE |
| LQA000 | LACQUER |
| PBA000 | LEAD |
| PBB000 | LEAD ALLOY |
| NLA000 | NICKEL |
| LCA000 | OIL |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PCA000 | PLASTIC |
| RHA000 | RHODIUM |
| RCA000 | RUBBER |
| AGA000 | SILVER |
| MSC000 | TAR |
| SNA000 | TIN |
| VAA000 | VARNISH |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AUC | INSIDE |
| 3AUW | OUTSIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
AAGT*JWALL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE WALL,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAGTJAB2.0*;AAGTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAB2.0*;ABGLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMZ*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMZJAC2.0*;ABMZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAB2.0*;ASDBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
HGTH*JHEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN OBJECT,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(HGTHJAB2.0*;HGTHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHA*JFIRST END INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHAJAC2.0*;AAHAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHB*JFIRST END OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHBJAC2.0*;AAHBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHC*JFIRST END TELESCOPING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHCJAC2.0*;AAHCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHD*JFIRST END BEAD OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHDJAA2.0*;AAHDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHE*JFIRST END FLARE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHEJAC2.0*;AAHEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHF*JFIRST END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHFJAC2.0*;AAHFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHG*JFIRST END GROOVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHGJAB2.0*;AAHGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHH*JFIRST END GROOVE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHHJAC2.0*;AAHHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHJ*JFIRST END LENGTH FROM GROOVE TO END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHJJAC2.0*;AAHJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHK*JFIRST END BEAD WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHKJAB2.0*;AAHKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHL*JFIRST END UNDERCUT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHLJAA2.0*;AAHLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHM*JFIRST END LENGTH FROM BEAD CENTER TO END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHMJAA2.0*;AAHMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQYM*JFIRST END NOMINAL THREAD SIZE
THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQYMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ATKT*DFIRST END THREAD SERIES
A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF THE FIRST END.
Enter the applicable reply code from the table below
(ATKTDFB)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| ZP | BSP. L |
| FB | BSP.F |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| GS | NGS |
| GT | NGT |
| SP | NPS |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| TS | NPTS |
| PT | PTF-SAE SHORT |
| UN | UN |
| FF | UN-12 |
| FG | UN-16 |
| FC | UN-4 |
| FD | UN-6 |
| FE | UN-8 |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CQKK*AFIRST END THREAD QUANTITY PER INCH
THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CQKKAB3)
IF STYLE/REPLY CODE(s) 3 OR 16 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHR)
IF STYLE/REPLY CODE(s) 6 OR 17 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHQ and AAHS)
IF STYLE/REPLY CODE(s) 7 OR 8 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (CRNB and CRMX and ATLB)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHT)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHV)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHR and AAHU)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHQ and AAHR and AAHU)
IF STYLE/REPLY CODE(s) 13 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHW and AAHX and AAHY)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHR and AAHT and AAJB and AAHZ)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC AAHP, YOU MUST ANSWER MRC (AAHR and AAJA)
AAHP*LSECOND END STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE SECOND END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAHPL7)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAB1037 | 1 | PLAIN |
| AAB1044 | 10 | FLANGE |
| AAB1045 | 11 | SINGLE FLARE |
| AAB1046 | 12 | DOUBLE FLARE |
| AAB1047 | 13 | OUTSIDE GROOVED |
| AAB1048 | 14 | OUTSIDE BEADED |
| AAB1049 | 15 | OUTSIDE UNDERCUT |
| AAB1050 | 16 | SWELLED OR STRETCHED DIAMETER |
| AAB1051 | 17 | HUB |
| AAB1038 | 2 | BEVELED |
| AAB1039 | 3 | OUTSIDE UPSET |
| AAB1040 | 6 | BELL |
| AAB1041 | 7 | THREADED EXTERNAL |
| AAB1042 | 8 | THREADED INTERNAL |
| AAB1043 | 9 | SPIGOT |
AAHQ*JSECOND END INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHQJAC2.0*;AAHQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHR*JSECOND END OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHRJAB2.0*;AAHRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHS*JSECOND END TELESCOPING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHSJAB2.0*;AAHSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHT*JSECOND END BEAD OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHTJAC2.0*;AAHTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHU*JSECOND END FLARE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHUJAC2.0*;AAHUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHV*JSECOND END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHVJAA2.0*;AAHVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHW*JSECOND END GROOVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHWJAB2.0*;AAHWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHX*JSECOND END GROOVE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHXJAC2.0*;AAHXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHY*JSECOND END LENGTH FROM GROOVE TO END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHYJAC2.0*;AAHYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAHZ*JSECOND END BEAD WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHZJAA2.0*;AAHZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAJA*JSECOND END UNDERCUT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAJAJAA2.0*;AAJAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAJB*JSECOND END LENGTH FROM BEAD CENTER TO END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAJBJAB2.0*;AAJBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRNB*JSECOND END NOMINAL THREAD SIZE
THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRNBJL2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ATLB*DSECOND END THREAD SERIES
A DESIGNATION INDICATING THE DIAMETER-PITCH COMBINATION AND THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A SERIES OF SPECIFIC DIAMETERS OF THE SECOND END.
Enter the applicable reply code from the table below
(ATLBDFC)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| ZP | BSP. L |
| FB | BSP.F |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| GS | NGS |
| GT | NGT |
| SP | NPS |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| TS | NPTS |
| PT | PTF-SAE SHORT |
| UN | UN |
| FF | UN-12 |
| FG | UN-16 |
| FC | UN-4 |
| FD | UN-6 |
| FE | UN-8 |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CRMX*ASECOND END THREAD QUANTITY PER INCH
THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CRMXAV2)
AAJH*DWELDING METHOD
THE MEANS BY WHICH THE SEAM IS WELDED.
Enter the applicable reply code from the table below
(AAJHDFL*;AAJHDFB$DXG*)
| Table 1 |
| Reply Code (AA40) | Reply |
| DS | DOUBLE SUBMERGED ARC |
| ER | ELECTRIC RESISTANCE |
| FB | FURNACE BUTT |
| FL | FURNACE LAP |
| FS | FUSION |
| XG | OXY-ACETYLENE GAS |
HEAT*DHEAT TREATMENT
A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM.
Enter the applicable reply code from the table below
(HEATDAW*;HEATDCV$DRK*;HEATDCV$$DRK*)
| Table 1 |
| Reply Code (AD05) | Reply |
| BP | ANNEALED |
| CK | ANNEALED TO A NOMINAL GRAIN SIZE 0.015 |
| CL | ANNEALED TO A NOMINAL GRAIN SIZE 0.025 |
| CM | ANNEALED TO A NOMINAL GRAIN SIZE 0.035 |
| EF | ANNEALED TO A NOMINAL GRAIN SIZE 0.040 |
| CN | ANNEALED TO A NOMINAL GRAIN SIZE 0.050 |
| CR | COLD DRAWN |
| BX | COLD DRAWN 1/2 HARD CONDITION |
| BW | COLD DRAWN 1/4 HARD CONDITION |
| BV | COLD DRAWN 1/8 HARD CONDITION |
| BY | COLD DRAWN 3/4 HARD CONDITION |
| BZ | COLD DRAWN FULL HARD CONDITION |
| BU | COLD DRAWN OR COLD FORGED TO PRODUCE CHANGES IN PROPERTIES |
| HS | COLD FINISH |
| DA | COLD WORKED |
| EG | DRAWN TEMPER |
| AD | F-AS FABRICATED |
| CA | H-12 STRAIN HARDENED, 1/2 HARD |
| AG | H-14 STRAIN HARDENED, 1/2 HARD |
| DE | H-16 STRAIN HARDENED, FULL HARD |
| AJ | H-18 STRAIN HARDENED, FULL HARD |
| DF | H-32 STRAIN HARDENED AND STABILIZED TO 1/2 HARD |
| AS | H-34 STRAIN HARDENED AND STABILIZED TO 1/2 HARD |
| DG | H-36 STRAIN HARDENED AND STABILIZED TO FULL HARD |
| AU | H-38 STRAIN HARDENED AND STABILIZED TO FULL HARD |
| BM | HARD DRAWN |
| PJ | HOT FINISH |
| CT | HOT ROLLED |
| CV | NORMALIZED |
| BQ | NORMALIZED AND STRESS RELIEVED |
| BS | NORMALIZED AND TEMPERED |
| AB | O-ANNEALED |
| AC | O-ANNEALED, RECRYSTALLIZED |
| JQ | PICKLED |
| EN | QUENCHED |
| BT | QUENCHED AND TEMPERED |
| BB | SOFT ANNEALED |
| CB | STRESS RELIEVED |
| AW | T-3 SOLUTION HEAT TREATED AND COLD WORKED |
| AY | T-4 SOLUTION HEAT TREATED AND NATURAL AGED |
| DH | T-42 SOLUTION HEAT TREATED AND ARTIFICIALLY AGED |
| AZ | T-6 SOLUTION HEAT TREATED AND ARTIFICIALLY AGED |
| DJ | T-62 SOLUTION HEAT TREATED AND ARTIFICIALLY AGED |
| RX | T-651 SOLUTION HEAT TREATED, ARTIFICALLY AGED, AND STRESS RELIEVED BY STRETCHING |
| RK | T-6510 SOLUTION HEAT TREATED |
| RL | T-6511 SOLUTION HEAT TREATED |
| DK | T-73 SOLUTION HEAT TREATED AND ARTIFICIALLY AGED |
| DL | T-81 SOLUTION HEAT TREATED AND ARTIFICIALLY AGED |
CQHT*HSURFACE CONDITION AND LOCATION
THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE AND ITS LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CQHTHAACGR2.0*;CQHTHAACGR2.0$HAACGR2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| AAB | INSIDE |
| AAC | OUTSIDE |
| Table 2 |
| Reply Code (AN72) | Reply |
| GR | GROUND |
| PL | POLISHED |
CRWF*JTHREAD PROTECTIVE DEVICE AND QUANTITY
AN ITEM APPLIED TO THE THREADED END OF AN ITEM TO GUARD AGAINST DAMAGE DURING SHIPPING,STORAGE,AND HANDLING,AND THE NUMBER PROVIDED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CRWFJP2*;CRWFJP2$$JP3*)
| Table 1 |
| Reply Code (AN77) | Reply |
| C | COUPLING |
| P | PROTECTOR |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAAB*;CBBLDAAC$$DAAB*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AAC | COILED |
| AAB | ENDS SEALED FOR REFRIGERATION SERVICE |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAA2.0*;ABHPJAA2.0$JAA2.0*;ABHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information