A ferrous or nonferrous product of solid rectangular cross section uniform throughout. It is made to specific strength for the purpose of arresting firearm projectiles or fragments.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED30873*)
AARNDFABRICATION METHOD
THE PROCESS USED IN MANUFACTURING THE ITEM.
Enter the applicable reply code from the table below
(AARNDGR*;AARNDKW$DGZ*;AARNDKW$$DGZ*)
| Table 1 |
| Reply Code (AA62) | Reply |
| AN | CAST |
| KQ | CENTRIFUGAL CAST |
| DK | COLD DRAWN |
| GW | COLD FINISH |
| GX | COLD ROLLED |
| KR | CONTINUOUS CAST |
| KS | DIE CAST |
| JX | DRAWN |
| GR | EXTRUDED |
| AJ | FORGED |
| GY | HARD DRAWN |
| GZ | HARD ROLLED |
| HA | HOT FINISH |
| HB | HOT ROLLED |
| KT | PERMANENT MOLD CAST |
| AS | ROLLED |
| KW | SAND CAST |
| HC | SINTERED |
| BB | WELDED |
| DF | WROUGHT |
CQBCJMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CQBCJSTEXT1234*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
CQHQJMINIMUM YIELD STRENGTH
THE STRESS AT WHICH A MATERIAL EXHIBITS A SPECIFIED LIMITING DEVIATION FROM THE PROPORTIONALITY OF STRESS OR STRAIN.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CQHQJS2*)
| Table 1 |
| Reply Code (AN71) | Reply |
| S | MEGAPASCALS |
| Z | NEWTONS PER SQUARE MILLIMETER |
| P | POUNDS PER SQUARE INCH |
AGXWDPHYSICAL FORM
THE RECOGNIZED SHAPE, CONFIGURATION, STRUCTURE, OR MOLD OF A SUBSTANCE, NATURAL OR REFINED, THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Enter the applicable reply code from the table below
(AGXWDAJM)
| Table 1 |
| Reply Code (AE98) | Reply |
| ADP | COIL |
| AJM | FLAT STOCK |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDSTF000*;MATTDTTB000$DAL2218*;MATTDTTB000$$DAL2218*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2218 | ALUMINUM ALLOY 2218 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7039 | ALUMINUM ALLOY 7039 |
| ZSA000 | COMPOSITION |
| CUB000 | COPPER ALLOY |
| FG0000 | FIBERGLASS |
| NLB000 | NICKEL ALLOY |
| PCN000 | PLASTIC PHENOLIC |
| AAA009 | POLYETHYLENE, HIGH MODULUS (HMPE) |
| STA000 | STEEL |
| ZSC000 | STEEL ALLOY |
| ST1009 | STEEL COMP 1009 |
| ST1020 | STEEL COMP 1020 |
| ST0302 | STEEL COMP 302 |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0316 | STEEL COMP 316 |
| ST0410 | STEEL COMP 410 |
| ST4140 | STEEL COMP 4140 |
| ST4340 | STEEL COMP 4340 |
| STB000 | STEEL CORROSION RESISTING |
| ST0552 | STEEL UNS K02600 |
| ST1789 | STEEL UNS K11918 |
| ZRF000 | STEEL,ARMOR |
| STF000 | STEEL,CARBON |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TT0052 | TITANIUM ALLOY UNS R56400 |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CYHX*AVEHICLE DESIGN CONTROL ACTIVITY
THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE GOVERNMENT AGENCY,INDUSTRIAL ORGANIZATION,OR OTHER ENTITY,WHICH CONTROLS THE DESIGN OF THE VEHICLE.
Enter the alpha-numeric reply with five character(s) exactly.
(CYHXAF0C1E)
CYHY*AVEHICLE IDENTIFICATION DESIGNATOR
THE NAME OR COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH IDENTIFY THE SPECIFIC VEHICLE.
Enter the alpha-numeric reply with a minimum of one character.
(CYHYAL5)
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
CZNF*ACOLOR CHIP NUMBER
THE IDENTIFYING NUMBER FOR THE COLOR CHIP.
Enter the alpha-numeric reply with a minimum of one character.
(CZNFAE2)
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPRA000*;SFTTDPHC000$DPRA001*;SFTTDPHC000$$DPRA001*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| XXG000 | BLACK OXIDE |
| CDA000 | CADMIUM |
| AAA001 | CARC (CHEMICAL AGENT RESISTANT COATING) |
| AAA013 | CARC (CHEMICAL AGENT RESISTANT COATING), ALIPHATIC POLYURETHANE |
| AAA017 | CATHODIC ELECTRODEPOSITION LEAD AND CHROMATE FREE |
| AAA002 | CHEMICAL |
| MSD000 | EPOXY |
| NNC000 | NON-CHROMIC ACID RINSE |
| AAA000 | PAINTED |
| PSA000 | PASSIVATE |
| PHC000 | PHOSPHATE MANGANESE |
| PHD000 | PHOSPHATE ZINC |
| AAA011 | POLYURETHANE PAINT-LEAD,CADMIUM AND HEXAVALENT CHROMIUM FREE |
| AAA004 | POWDER COATED |
| PRA000 | PRIMER |
| PRF000 | PRIMER EPOXY |
| PRA001 | PRIMER EPOXY-LEAD AND CHROMIUM FREE |
| ZNM000 | PRIMER-HEXAVALENT CHROMIUM FREE |
| AAA010 | PRIMER-LEAD AND HEXAVALENT CHROMIUM FREE |
| ZNA000 | ZINC |
| ZNH000 | ZINC PLATED (USE ZNA000) AND (USE MRC BRFC) |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDWH0000*;HUESDGR0000$DTA0000*;HUESDGR0000$$DTA0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| GR0000 | GREEN |
| GR0494 | GREEN, 383 |
| NA0000 | NATURAL |
| TA0000 | TAN |
| TA0099 | TAN, 686A |
| WH0000 | WHITE |
BBJX*DMOUNTING POSITION
THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BBJXDAAB*;BBJXDAAC$DAMF*;BBJXDAAC$$DAMF*)
| Table 1 |
| Reply Code (AM84) | Reply |
| AMF | EXTERIOR |
| ABG | FRONT |
| AFL | INTERIOR |
| AAB | LEFT SIDE |
| ABK | REAR |
| AAC | RIGHT SIDE |
HEAT*DHEAT TREATMENT
A COMBINATION OF TIMED HEATING AND COOLING OPERATIONS APPLIED FOR THE PURPOSE OF ANNEALING OR HARDENING THE ITEM.
Enter the applicable reply code from the table below
(HEATDQC*;HEATDCK$DRQ*;HEATDCK$$DRQ*)
| Table 1 |
| Reply Code (AD05) | Reply |
| GJ | AGE HARDENING |
| BP | ANNEALED |
| CK | ANNEALED TO A NOMINAL GRAIN SIZE 0.015 |
| CL | ANNEALED TO A NOMINAL GRAIN SIZE 0.025 |
| CM | ANNEALED TO A NOMINAL GRAIN SIZE 0.035 |
| CN | ANNEALED TO A NOMINAL GRAIN SIZE 0.050 |
| CP | ANNEALED TO A NOMINAL GRAIN SIZE 0.070 |
| CQ | ANNEALED TO A NOMINAL GRAIN SIZE 0.100 |
| FZ | ANNEALED TO A NOMINAL GRAIN SIZE 0.120 |
| HT | ARTIFICALLY AGED |
| MP | AS CAST |
| CS | AS FABRICATED |
| CZ | CASEHARDENED |
| LR | DRY ANNEALED |
| GA | EIGHTH HARD |
| GC | EXTRA HARD |
| GD | EXTRA SPRING TEMPER |
| AD | F-AS FABRICATED |
| AE | H-1 STRAIN HARDENED |
| EX | H-111 STRAIN HARDENED |
| AV | H-112 AS ROLLED |
| GB | H-116 SPECIALLY TREATED |
| HJ | H-117 SPECIALLY TREATED |
| AF | H-12 STRAIN HARDENED, 1/4 HARD |
| AG | H-14 STRAIN HARDENED, 1/2 HARD |
| AH | H-16 STRAIN HARDENED, 3/4 HARD |
| AJ | H-18 STRAIN HARDENED, FULL HARD |
| AK | H-19 STRAIN HARDENED, EXTRA HARD |
| PK | H-20 STRAIN HARDENED |
| PL | H-22 STRAIN HARDENED |
| PM | H-24 STRAIN HARDENED |
| PN | H-26 STRAIN HARDENED |
| PP | H-28 STRAIN HARDENED |
| PQ | H-32 STRAIN HARDENED |
| QP | H-321 STRAIN HARDENED |
| QQ | H-323 STRAIN HARDENED |
| PR | H-34 STRAIN HARDENED |
| QR | H-343 STRAIN HARDENED |
| PS | H-36 STRAIN HARDENED |
| PT | H-38 STRAIN HARDENED |
| CF | HALF HARD |
| CH | HARD |
| LS | HARD TEMPER |
| GY | INTERMEDIATE TEMPER |
| BC | LIGHT ANNEALED |
| PW | NATURAL AGED |
| GZ | NITRIDED |
| CV | NORMALIZED |
| AB | O-ANNEALED |
| HB | OIL QUENCHED |
| PX | PARTIALLY ANNEALED |
| PZ | PARTIALLY ANNEALED TO 1/2 HARD |
| PY | PARTIALLY ANNEALED TO 1/4 HARD |
| QA | PARTIALLY ANNEALED TO 3/4 HARD |
| QB | PARTIALLY ANNEALED TO FULL HARD |
| CE | QUARTER HARD |
| DD | QUENCH HARDENED |
| EN | QUENCHED |
| CD | SKIN HARD |
| HD | SOFT |
| BB | SOFT ANNEALED |
| GE | SOFT TEMPER |
| GF | SOLUTION TREATED |
| BR | SPHEROIDIZED |
| CJ | SPRING TEMPER |
| PH | STABILIZED |
| QD | STABILIZED TO 1/2 HARD |
| QC | STABILIZED TO 1/4 HARD |
| QE | STABILIZED TO 3/4 HARD |
| QF | STABILIZED TO FULL HARD |
| ME | STRAIN HARDENED |
| CB | STRESS RELIEVED |
| QS | STRESS RELIEVED BY STRETCHING |
| QT | T-1 SOLUTION HEAT TREATED |
| QG | T-3 SOLUTION HEAT TREATED |
| RB | T-351 SOLUTION HEAT TREATED |
| RF | T-3510 SOLUTION HEAT TREATED |
| RG | T-3511 SOLUTION HEAT TREATED |
| QH | T-36 SOLUTION HEAT TREATED |
| TM | T-361 SOLUTION HEAT TREATED |
| QJ | T-4 SOLUTION HEAT TREATED |
| RC | T-451 SOLUTION HEAT TREATED |
| RH | T-4510 SOLUTION HEAT TREATED |
| RJ | T-4511 SOLUTION HEAT TREATED |
| QW | T-5 SOLUTION HEAT TREATED |
| TC | T-52 SOLUTION HEAT TREATED |
| QK | T-6 SOLUTION HEAT TREATED |
| SD | T-62 SOLUTION HEAT TREATED |
| RD | T-651 SOLUTION HEAT TREATED |
| RK | T-6510 SOLUTION HEAT TREATED |
| RL | T-6511 SOLUTION HEAT TREATED |
| QY | T-73 SOLUTION HEAT TREATED |
| TB | T-7351 SOLUTION HEAT TREATED |
| RQ | T-73510 SOLUTION HEAT TREATED |
| RR | T-73511 SOLUTION HEAT TREATED |
| TN | T-7451 SOLUTION HEAT TREATED |
| QZ | T-76 SOLUTION HEAT TREATED |
| RM | T-7651 SOLUTION HEAT TREATED |
| RS | T-76510 SOLUTION HEAT TREATED |
| RT | T-76511 SOLUTION HEAT TREATED |
| QX | T-8 SOLUTION HEAT TREATED |
| QM | T-81 SOLUTION HEAT TREATED |
| RA | T-84 SOLUTION HEAT TREATED |
| RE | T-851 SOLUTION HEAT TREATED |
| RN | T-8510 SOLUTION HEAT TREATED |
| RP | T-8511 SOLUTION HEAT TREATED |
| QL | T-86 SOLUTION HEAT TREATED |
| FJ | T-87PRECIPITATION HEAT TREATED |
| UC | TEMPER DESIGNATION, T861 |
| EP | TEMPERED |
| CG | THREE QUARTERS HARD |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAC2.0*;ABTBJAC2.0$JAC2.0*;ABTBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
ACHY*DMOUNTING HOLE TYPE
INDICATES THE TYPE OF HOLES PROVIDED IN THE ITEM TO FACILITATE MOUNTING TO ANOTHER ITEM.
Enter the applicable reply code from the table below
(ACHYDP)
| Table 1 |
| Reply Code (AB68) | Reply |
| A | COUNTERBORED |
| B | COUNTERSUNK |
| C | PLAIN |
| P | SLOTTED |
| D | THREADED |
| U | THRU HOLE |
| E | UNTHREADED |
SFCD*DSURFACE CONDITION
THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFCD3AFGDDS*;SFCD3AFGDDS$DPL*;SFCD3AFGDDS$$DPL*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AFG | BOTH SIDES |
| 3AFJ | ONE SIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN72) | Reply |
| BB | BEST BRIGHT |
| BT | BRIGHT |
| CD | CENTERLESS GROUND |
| CP | CHROME PICKLED |
| DS | DESCALED |
| DL | DULL |
| DM | DULL MATTE |
| GR | GROUND |
| MA | MACHINE |
| AF | OIL FREE |
| AL | OILED |
| PK | PICKLED |
| PL | POLISHED |
| PG | PRECISION GROUND |
| RM | ROUGH MACHINED |
| RT | ROUGH TURNED |
| SB | SAND BLASTED |
| SN | SATIN |
| TN | TURNED |
AQQR*DEDGE TYPE
INDICATES THE TYPE OF EDGE ON THE ITEM.
Enter the applicable reply code from the table below
(AQQRDDE*;AQQRDDG$DDH*;AQQRDDG$$DDH*)
| Table 1 |
| Reply Code (AL25) | Reply |
| CJ | BEVELED |
| CR | MILLED |
| DF | NO. 1 BEVELED |
| DG | NO. 1 ROUND |
| DH | NO. 1 SQUARE |
| CS | NO. 2 |
| CT | NO. 3 |
| CW | NO. 4 |
| CX | NO. 5 |
| CY | NO. 6 |
| CZ | PLANED |
| DA | ROLLED |
| DB | ROUNDED |
| DC | SAWED |
| DD | SHEARED |
| DE | SLIT |
| CF | SQUARE |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJFC2.0*;ABRYJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| A | INCHES |
| M | METERS |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) A1 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (ABGL and ABRY and ADPC and ADVM and AKSV and CXJG and CXKF) or (ABGL and ABRY and ADPC and ADVM and AKSV and CXJG and ADPD)
IF STYLE/REPLY CODE(s) A3 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (ABGL and ABRY and ADPC and ADPD and ADVM and AKSV and BMNT and CXKF) or (ABGL and ABRY and ADPC and ADPD and ADVM and AKSV and BMNT and CXJG)
IF STYLE/REPLY CODE(s) A2 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (ABGL and ABRY and ADPC and ADPD and ADVM and AKSV and BMNS and BMNT)
IF STYLE/REPLY CODE(s) A5 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (ABGL and ABRY and ADPC and ADPD and ADVM and CXKF and BMNQ and BMNR)
IF STYLE/REPLY CODE(s) A10 WERE ENTERED FOR MRC AGTA, YOU MUST ANSWER MRC (ABGL and ABRY and ADVM)
AGTA*LBASIC SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE BASIC APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AGTALA5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAR1877 | A1 | ROUND |
| AAR1881 | A10 | SOLID |
| AAR1878 | A2 | ROUND |
| AAR1879 | A3 | ROUND |
| AAR1880 | A5 | SLOTTED |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAC2.0*;ABGLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPC*JDISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPCJAB2.0*;ADPCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPD*JDISTANCE FROM FIRST HOLE CENTERLINE TO END ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPDJAB2.0*;ADPDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVM*JCROSS-SECTIONAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A CROSS SECTION,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVMJAA2.0*;ADVMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKSV*JPERFORATION DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OPENING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKSVJAC2.0*;AKSVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXJG*JPERFORATION CENTER TO CENTER DISTANCE ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXJGJAA2.0*;CXJGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXKF*JPERFORATION CENTER TO CENTER DISTANCE ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXKFJAC2.0*;CXKFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMNQ*JPERFORATION ELONGATION LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMNQJAB2.0*;BMNQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMNR*JPERFORATION ELONGATION WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMNRJAC2.0*;BMNRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMNS*JPERFORATION CENTER TO CENTER DISTANCE ALONG UPWARD SLOPE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMNSJAA2.0*;BMNSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BMNT*JPERFORATION CENTER TO CENTER DISTANCE ALONG DOWNWARD SLOPE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BMNTJAC2.0*;BMNTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXKT*JHOLE QUANTITY
NONE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CXKTJMD2*)
| Table 1 |
| Reply Code (AG67) | Reply |
| MD | PER SQUARE INCH |
| ME | PER SQUARE METER |
BRDT*DLEVELING METHOD
THE MEANS USED TO LEVEL THE ITEM.
Enter the applicable reply code from the table below
(BRDTDHW*;BRDTDHT$DHT*;BRDTDHT$$DHT*)
| Table 1 |
| Reply Code (AA62) | Reply |
| HT | ROLLER |
| HW | STRETCHER |
BRFD*JWEIGHT PER UNIT MEASURE
THE WEIGHT OF THE ITEM WITH RESPECT TO A UNIT OF MEASURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BRFDJBD2.0*)
| Table 1 |
| Reply Code (AG69) | Reply |
| AW | KILOGRAMS PER METER |
| AQ | KILOGRAMS PER SQUARE METER |
| BL | POUNDS PER LINEAR FOOT |
| BE | POUNDS PER PIECE |
| BD | POUNDS PER SQUARE FOOT |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CF | CUBIC FEET |
| CN | CUBIC INCHES |
| CM | CUBIC METERS |
| CB | CUBIC MILLIMETERS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDAGA000$DAUA000*;PRMTDAGA000$$DAUA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000R2.0*;PMWTJAUA000R2.0$$JAUA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJRHA0002.0*;PMLCJRHA0002.0$JRHA0002.0*;PMLCJRHA0002.0$$JRHA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
ALBY*DUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDAHX*;ALBYDBAS$DAMC*;ALBYDBAS$$DAMC*)
| Table 1 |
| Reply Code (AH21) | Reply |
| AHX | AIRCRAFT |
| AAG | DENTAL |
| BAS | FOOD HANDLING |
| BAR | FOOD PROCESSING |
| AMD | HULL |
| AMC | SHIPBUILDING |
| AME | STRUCTURAL |
| AMF | VEHICULAR |
BRFB*JCOVERING AREA
THE AREA,PER UNIT OF WEIGHT,THE ITEM WILL COVER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BRFBJHK2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| HJ | SQUARE INCHES PER POUND |
| HK | SQUARE MILLIMETERS PER KILOGRAM |
BRFC*DCOATING METHOD
THE MEANS BY WHICH THE COATING IS APPLIED.
Enter the applicable reply code from the table below
(BRFCDAF*;BRFCDAE$DAF*)
| Table 1 |
| Reply Code (AK01) | Reply |
| AE | ELECTROPLATED |
| AF | HOT DIPPED |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAM*;BBRGDAN$DAJ*;BBRGDAN$$DAJ*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ECWT*JEXTERIOR CONTAINER WEIGHT
THE MEASURED WEIGHT OF THE EXTERIOR CONTAINER. PLEASE USE MRC AJWK WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ECWTJKG2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CSYX*JNOMINAL HOLE DIAMETER AND QUANTITY
THE NOMINAL LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HOLE,AND TERMINATES AT THE CIRCUMFERENCE,AND THE NUMBER OF HOLES.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYXJAAAB2.0*;CSYXJAAAB2.0$JAAAB2.0*;CSYXJAAAB2.0$$JAAAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AP65) | Reply |
| AAH | EIGHT HOLES |
| AAE | FIVE HOLES |
| AAD | FOUR HOLES |
| AAJ | NINE HOLES |
| AAA | ONE HOLE |
| AAG | SEVEN HOLES |
| AAF | SIX HOLES |
| AAK | TEN HOLES |
| AAC | THREE HOLES |
| AAB | TWO HOLES |
CQFM*JHARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQFMJAGA2.0*)
| Table 1 |
| Reply Code (AC26) | Reply |
| RA | ROCKWELL A |
| RB | ROCKWELL B |
| RC | ROCKWELL C |
| RD | ROCKWELL D |
| RE | ROCKWELL E |
| RQ | ROCKWELL H |
| AG | SHORE |
| SA | SHORE DUROMETER A |
| SB | SHORE DUROMETER B |
| SE | SHORE DUROMETER C |
| SD | SHORE DUROMETER D |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information