A structural shape fabricated from nonmetallic material(s) resembling the letter "L" in cross-sectional form. It may have a reinforcing agent(s) and backing. Excludes:SEAL, NONMETALLIC ANGLE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED30217*)
IF STYLE/REPLY CODE(s) A1 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABKW and ABMK and ADXL and AJGP and ADXZ)
IF STYLE/REPLY CODE(s) A2 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABKW and ABMK and ADXL and AJGP and AJGL)
IF STYLE/REPLY CODE(s) A3 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABKW and ABMK and ADXJ and ADXL and AJGP and AJGQ and ADXZ)
IF STYLE/REPLY CODE(s) A4 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABMK and ABKW and ADXL and AJGP and AJGM and ADXZ)
IF STYLE/REPLY CODE(s) A5 WERE ENTERED FOR MRC AAGR, YOU MUST ANSWER MRC (ABKW and ABMK and ADXL and AJGP and AJGL and AJGM)
AAGRLCROSS-SECTIONAL SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE CROSS-SECTIONAL SHAPE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAGRLA2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| CH10002 | A1 | ANGLE |
| CH10003 | A2 | ANGLE |
| CH10004 | A3 | ANGLE |
| CH10005 | A4 | ANGLE |
| CH10006 | A5 | ANGLE |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADXJ*JLEFT SIDE FLANGE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADXJJAB2.0*;ADXJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADXL*JLEFT SIDE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADXLJAC2.0*;ADXLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJGP*JBASE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJGPJAB2.0*;AJGPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJGQ*JBASE FLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BASE FLANGE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJGQJAC2.0*;AJGQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJGL*JFILLET RADIUS WHERE LEFT FLANGE JOINS BASE FLANGE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJGLJAA2.0*;AJGLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJGM*JOUTER RADIUS WHERE LEFT FLANGE JOINS BASE FLANGE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJGMJAA2.0*;AJGMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADXZ*BLEFT INSIDE ANGLE IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ADXZB2.0)
IF STYLE/REPLY CODE(s) B1 WERE ENTERED FOR MRC BHQU, YOU MUST ANSWER MRC (ADYF and ADYG)
IF STYLE/REPLY CODE(s) B2 WERE ENTERED FOR MRC BHQU, YOU MUST ANSWER MRC (AJGN)
IF STYLE/REPLY CODE(s) B3 WERE ENTERED FOR MRC BHQU, YOU MUST ANSWER MRC (ADYF)
IF STYLE/REPLY CODE(s) B4 WERE ENTERED FOR MRC BHQU, YOU MUST ANSWER MRC (ADYG)
BHQULLEFT-SIDE FLANGE TIP STYLE
THE STYLE DESIGNATION CORRESPONDING TO THE SHAPE OF THE LEFT-SIDE FLANGE TIP.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BHQULB4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR01858 | B1 | LEFT W/INSIDE & OUTSIDE CORNER RADI |
| DR01859 | B2 | LEFT FULL RADIUS |
| DR01861 | B3 | LEFT W/OUTSIDE RADIUS |
| DR01862 | B4 | LEFT W/INSIDE RADIUS |
| DR01863 | B5 | LEFT SQUARE END |
ADYF*JLEFT SIDE FLANGE TOP OUTER RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADYFJAC2.0*;ADYFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADYG*JLEFT SIDE FLANGE TOP INNER RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADYGJAB2.0*;ADYGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJGN*JLEFT SIDE FLANGE TOP RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJGNJAC2.0*;AJGNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) C2 WERE ENTERED FOR MRC BHQV, YOU MUST ANSWER MRC (ADXE)
IF STYLE/REPLY CODE(s) C3 WERE ENTERED FOR MRC BHQV, YOU MUST ANSWER MRC (ADXF)
IF STYLE/REPLY CODE(s) C4 WERE ENTERED FOR MRC BHQV, YOU MUST ANSWER MRC (AJGK)
IF STYLE/REPLY CODE(s) C5 WERE ENTERED FOR MRC BHQV, YOU MUST ANSWER MRC (ADXE and ADXF)
BHQVLBASE FLANGE TIP STYLE
THE STYLE DESIGNATION CORRESPONDING TO THE SHAPE OF THE BASE FLANGE TIP.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BHQVLC1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR01860 | C1 | BASE SQUARE END |
| DR01864 | C2 | BASE UPPER RADIUS |
| DR01865 | C3 | BASE LOWER RADIUS |
| DR01866 | C4 | BASE FULL RADIUS |
| DR01867 | C5 | BASE W/UPPER AND LOWER RADIUS |
ADXE*JRIGHT FLANGE INNER SIDE RADIUS AT TOE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADXEJAB2.0*;ADXEJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADXF*JRIGHT FLANGE OUTER SIDE RADIUS AT TOE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADXFJAC2.0*;ADXFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJGK*JBASE FLANGE TIP RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJGKJAC2.0*;AJGKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAA2.0*;ABRYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDRCE000*;MATT3AEEDRCE000$DSLK000*;MATT3AEEDRCE000$$DSLK000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CMA | JACKET |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| PCA000 | PLASTIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE |
| PCP002 | PLASTIC, ACETAL-DELRIN COMPOSITION 100 AF |
| PCP001 | PLASTIC, ETHYLENE-PROPYLENE |
| RCE000 | RUBBER |
| RCAD00 | RUBBER BUTADIENE NITRILE |
| RC0019 | RUBBER BUTADIENE-ACRYLONITRILE CLASS NBR |
| RC0022 | RUBBER BUTADIENE-STYRENE CLASS SBR |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RC0010 | RUBBER ETHYLENE-PROPYLENE-DIENE CLASS EPDM |
| RCA000 | RUBBER NATURAL |
| RC0021 | RUBBER SILICONE CLASS Q |
| RCB000 | RUBBER SYNTHETIC |
| SLK000 | SILICONE |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CMA | JACKET |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
AGXWDPHYSICAL FORM
THE RECOGNIZED SHAPE, CONFIGURATION, STRUCTURE, OR MOLD OF A SUBSTANCE, NATURAL OR REFINED, THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Enter the applicable reply code from the table below
(AGXWDAV*;AGXWDAW$DAW*)
| Table 1 |
| Reply Code (AE98) | Reply |
| AV | CELLULAR |
| AW | SOLID |
AASFJNONMETALLIC HARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF A NONMETALLIC ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASFJAPS2.0*;AASFJBPS2.0$$JCPS2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 2 |
| Reply Code (AC26) | Reply |
| PS | PLASTOMETER SCALE |
| RE | ROCKWELL E |
| RL | ROCKWELL L |
| RM | ROCKWELL M |
| RR | ROCKWELL R |
| SR | SHORE DUROMETER |
| SA | SHORE DUROMETER A |
| SD | SHORE DUROMETER D |
AASHJMINIMUM TENSILE STRENGTH
THE MAXIMUM LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AASHJK2*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| L | KILOPASCALS |
| V | POUNDS PER SQUARE INCH |
ABJHJTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples.For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.If ISAC coding is authorized for this requirement and one or more of the temperature values in negative, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.Also precede the numeric portion of the reply with the letter “M” as in the fifth and sixth examples.
(ABJHJF68.0*; ABJHJC0.0$$JC35.0*; ABJHJFCM15.0*; ABJHJFM40.0$$JF75.0*; ABJH1BJFM25.0*; ABJH1BJCM35.0$$JCM5.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDAJT*;ADZCDAGE$DAJH*;ADZCDAGE$$DAJH*)
| Table 1 |
| Reply Code (AA65) | Reply |
| AJH | CORROSION |
| AAC | CORROSION RESISTANT |
| DNT | CRACK |
| AGC | FIRE RETARDANT |
| AAU | FLUID RESISTANT |
| AGD | HEAT DRY |
| AGE | HIGH TEMPERATURE |
| AGF | LOW TEMPERATURE |
| AAX | OIL RESISTANT |
| ACN | OZONE RESISTANT |
| AJF | TEAR |
| AEN | TEAR RESISTANT |
| AJT | WARP/TWIST |
| DNU | WEAR RESISTANT |
| ABN | WEATHER RESISTANT |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information