An item consisting of a refrigeration compressor and prime mover, it may be open or enclosed in a hermetically sealed housing, having inlet and outlet connections and facilities for mounting.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED29305*)
AAXJADUTY CYCLE IN PERCENT
THE PERCENTAGE OF TIME FOR WHICH THE ITEM IS DESIGNED TO GENERATE WITHOUT DEGRADATION OF RATED CAPACITY AND DISCHARGE PRESSURE.
Enter the numeric reply with a minimum of one digit.
(AAXJA10*)
AAXKDGAS FOR WHICH DESIGNED
THE MEDIA THE MACHINE IS DESIGNED TO COMPRESS.
Enter the applicable reply code from the table below
(AAXKDAAY*;AAXKDAAG$$DAAN*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AAB | AIR |
| AAG | CARBON DIOXIDE |
| AAH | DICHLORODIFLUOROMETHANE, TECHNICAL |
| AAJ | DRY SATURATED STEAM |
| AAK | HALOGENATED HYDROCARBON |
| AAL | HELIUM |
| AAM | HYDROGEN |
| AAN | NATURAL GAS |
| AAP | NITROGEN |
| AAQ | OXYGEN |
| AAR | REFRIGERANT R-11 |
| AAS | REFRIGERANT R-12 |
| AAT | REFRIGERANT R-13 |
| ABV | REFRIGERANT R-134A |
| AAW | REFRIGERANT R-22 |
| AAX | REFRIGERANT R-500 |
| AAY | REFRIGERANT R-502 |
| AAZ | STEAM-CARBON DIOXIDE |
| ABA | SULPHUR HEXAFLUORIDE |
AAXLJDISCHARGE FLOW RATE
THE RATED CAPACITY OF GAS DELIVERED BY THE LAST STAGE OF COMPRESSION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAXLJA2.0*)
| Table 1 |
| Reply Code (AC64) | Reply |
| A | CUBIC FEET PER MINUTE |
| C | CUBIC METERS PER MINUTE |
AAXMJDISCHARGE PRESSURE
THE GAGE PRESSURE OF GAS DELIVERED BY THE LAST STAGE OF COMPRESSION.REFERRED TO AS CONDENSING PRESSURE FOR REFRIGERATION COMPRESSORS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAXMJQ2.0*)
| Table 1 |
| Reply Code (AA95) | Reply |
| L | BARS |
| B | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| Q | KILOPASCALS |
| G | POUNDS PER SQUARE INCH GAGE |
AAYSBCOMPRESSOR SPEED AT RATED CAPACITY IN RPM
THE SPEED OF THE COMPRESSOR REQUIRED TO PRODUCE ITS RATED CAPACITY,EXPRESSED IN REVOLUTIONS PER MINUTE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAYSB2.0)
AAXPDCOOLING SYSTEM DESIGN
THE DESIGN OF THE SYSTEM NECESSARY TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF AN ITEM AND DISCHARGE TEMPERATURE OF THE COMPRESSED GASES.
Enter the applicable reply code from the table below
(AAXPDA)
| Table 1 |
| Reply Code (AA74) | Reply |
| B | MIXED |
| A | SINGLE |
AAXQ*DCOMPRESSED GAS COOLING MEDIUM
THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE COMPRESSED GASES. USE MRC ACZV AND ISAC TO TABLE 0094
Enter the applicable reply code from the table below
(AAXQDAAC*;AAXQDAAB$DAAD*;AAXQDAAB$$DAAD*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AAB | AIR |
| AAC | FRESH WATER |
| AAD | OIL |
| AAE | REFRIGERANT |
| AAF | SALT WATER |
AAXU*DGAS COOLING EQUIPMENT TYPE
THE POSITION OF THE GAS COOLING EQUIPMENT WHETHER BETWEEN STAGES /INTERCOOLER/,AFTER THE LAST STAGE /AFTERCOOLER/,OR BOTH.
Enter the applicable reply code from the table below
(AAXUDB*;AAXUDC$$DE*)
| Table 1 |
| Reply Code (AA76) | Reply |
| B | AIR TYPE AFTERCOOLER |
| C | AIR TYPE INTERCOOLER |
| D | LIQUID TYPE AFTERCOOLER |
| E | LIQUID TYPE INTERCOOLER |
AAXRDCOMPRESSOR COOLING MEDIUM
THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE COMPRESSOR. USE MRC ACZV AND ISAC TO TABLE 0094
Enter the applicable reply code from the table below
(AAXRDAAC*;AAXRDAAF$DAAB*;AAXRDAAF$$DAAB*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AAB | AIR |
| AAC | FRESH WATER |
| AAD | OIL |
| AAE | REFRIGERANT |
| AAF | SALT WATER |
AAXSDPRIME MOVER COOLING MEDIUM
THE COOLING MEDIUM USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE PRIME MOVER. USE MRC ACZV AND ISAC TO TABLE 0094
Enter the applicable reply code from the table below
(AAXSDAAB)
| Table 1 |
| Reply Code (AB75) | Reply |
| AAB | AIR |
| AAC | FRESH WATER |
| AAE | REFRIGERANT |
AAXV*DUNLOADER TYPE
THE METHOD BY WHICH A NO LOAD CONDITION IS OBTAINED FOR STARTING THE ITEM.
Enter the applicable reply code from the table below
(AAXVDAE*;AAXVDAD$$DAD*)
| Table 1 |
| Reply Code (AA77) | Reply |
| AD | AUTOMATIC |
| AE | MANUAL |
CXNTJBRAKE POWER REQUIRED
THE BRAKE POWER REQUIRED TO START AND OPERATE THE ITEM INCLUDING ALL ACCESSORIES AT THE ACTUAL RATED CAPACITY,EXPRESSED IN UNIT OF POWER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CXNTJL2.0*)
| Table 1 |
| Reply Code (AC33) | Reply |
| H | HORSEPOWER |
| L | KILOWATTS |
| W | WATTS |
AAXXDMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable reply code from the table below
(AAXXDA)
| Table 1 |
| Reply Code (AA78) | Reply |
| A | ANY ACCEPTABLE |
| AAC | BACK PACK |
| AAB | BASE |
| AAD | BRACKET |
| AAE | CASTER |
| AAF | HAND CARRY |
| AAG | HAND TRUCK |
| AAH | HORIZONTAL TANK |
| AAJ | MOTOR TRUCK |
| AAK | SKID |
| AAL | TRACTOR |
| AAM | TRAILER |
| AAN | VERTICAL TANK |
| AAP | WHEEL |
| AAQ | WHEELBARROW |
IF YOU ANSWER MRC AAXY, YOU MUST ANSWER MRC (AAXZ and AAYA)
AAXY*DRECIPROCATING COMPRESSOR DESIGN
THE RECIPROCATING COMPRESSOR DESIGN AS DETERMINED BY THE MECHANICAL ACTION BY WHICH COMPRESSION TAKES PLACE IN THE CYLINDER/S/ OF THE COMPRESSOR.
Enter the applicable reply code from the table below
(AAXYDB*;AAXYDC$DA*;AAXYDC$$DA*)
| Table 1 |
| Reply Code (AA79) | Reply |
| C | COMPOUND ACTING |
| B | DOUBLE ACTING |
| A | SINGLE ACTING |
AAXZ*ACYLINDER QUANTITY
THE NUMBER OF CYLINDERS INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAXZA10*)
AAYA*LCYLINDER ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ANGULAR ARRANGEMENT OF THE CYLINDERS.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAYAL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAA1003 | 1 | VERTICAL DESIGN |
| AAA1004 | 2 | HORIZONTAL DESIGN |
| AAA1005 | 3 | "V" DESIGN |
| AAA1006 | 4 | "W" DESIGN |
| AAA1007 | 5 | HORIZONTALLY OPPOSED DESIGN |
| AAA1008 | 6 | SEMI-RADIAL DESIGN |
| AAA1009 | 7 | RADIAL DESIGN |
| AAA1010 | 8 | L DESIGN |
AAYB*DROTARY COMPRESSOR DESIGN
THE MECHANICAL ACTION BY WHICH COMPRESSION TAKES PLACE.
Enter the applicable reply code from the table below
(AAYBDP)
| Table 1 |
| Reply Code (AA81) | Reply |
| A | AXIAL SCREW |
| B | LIQUID PISTON |
| P | ROTARY VANE |
| C | SLIDING VANE |
| D | TWO IMPELLER |
AAYC*DCENTRIFUGAL COMPRESSOR DESIGN
THE DESIGN OF A NONPOSITIVE DISPLACEMENT CENTRIFUGAL COMPRESSOR AS DETERMINED BY THE DIRECTION OF FLOW,WITH RESPECT TO THE AXIS,OF THE COMPRESSED GAS.
Enter the applicable reply code from the table below
(AAYCDB)
| Table 1 |
| Reply Code (AA80) | Reply |
| A | AXIAL FLOW |
| B | RADIAL FLOW |
AAYDASTAGE QUANTITY
THE NUMBER OF STAGES INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYDA10*)
AAYEBREFRIGERATION FLOW RATE IN TONS PER HOUR
THE REFRIGERATION CAPACITY OF THE ITEM AS RATED BY INDUSTRY,EXPRESSED IN TONS PER HOUR.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AAYEB2.0)
AAYF*JSUCTION PRESSURE
THE PRESSURE OF THE GAS AFTER IT HAS PASSED THROUGH THE EVAPORATOR AND PRIOR TO ITS COMPRESSION WITHIN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYFJK2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| F | BAR |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| L | KILOPASCALS |
| V | POUNDS PER SQUARE INCH |
IF STYLE/REPLY CODE(s) AD WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (CSBH and CQJY)
IF STYLE/REPLY CODE(s) AH WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AAYJ and AAYK)
IF STYLE/REPLY CODE(s) AL OR AM WERE ENTERED FOR MRC AKDJ, YOU MUST ANSWER MRC (AAYL)
AKDJDPRIME MOVER TYPE
INDICATES THE TYPE OF PRIME MOVER INCLUDED WITH THE UNIT.
Enter the applicable reply code from the table below
(AKDJDAH)
| Table 1 |
| Reply Code (AG27) | Reply |
| AC | DIESEL ENGINE |
| AD | ELECTRIC MOTOR |
| AE | GASOLINE ENGINE |
| AH | HYDRAULIC MOTOR |
| AL | STEAM ENGINE |
| AM | STEAM TURBINE |
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC CSBH, YOU MUST ANSWER MRC (FREQ and FAAZ)
CSBH*JVOLTAGE IN VOLTS AND CURRENT TYPE
THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHETHER ALTERNATING OR DIRECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBHJDC2.0*;CSBHJDC2.0$JDC2.1*)
| Table 1 |
| Reply Code (AN87) | Reply |
| AC | AC |
| DC | DC |
FREQ*BFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(FREQB2.0*;FREQB2.0$$BM2.0*)
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDB*;FAAZDA$DC*)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| C | THREE |
| B | TWO |
CQJY*JCURRENT TYPE AND RATING IN AMPS
INDICATES THE TYPE AND AMOUNT OF ELECTRICAL FLOW AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN AMPERES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJYJAC2.0*;CQJYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AN87) | Reply |
| AC | AC |
| DC | DC |
AAYJ*JHYDRAULIC FLUID FLOW RATE
THE AMOUNT OF HYDRAULIC FLUID REQUIRED TO OPERATE THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYJJM2.0*)
| Table 1 |
| Reply Code (AC64) | Reply |
| M | GALLONS PER MINUTE |
| E | LITERS PER MINUTE |
AAYK*JHYDRAULIC PRESSURE
THE GAGE PRESSURE REQUIRED TO OPERATE THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYKJL2.0*)
| Table 1 |
| Reply Code (AA95) | Reply |
| L | BARS |
| B | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| Q | KILOPASCALS |
| G | POUNDS PER SQUARE INCH GAGE |
AAYL*JSTEAM OPERATING PRESSURE
THE STEAM PRESSURE REQUIRED TO MOTIVATE THE STEAM ENGINE OR TURBINE USED AS THE PRIME MOVER.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAYLJQ2.0*)
| Table 1 |
| Reply Code (AA95) | Reply |
| L | BARS |
| B | KILOGRAMS PER SQUARE CENTIMETER GAGE |
| Q | KILOPASCALS |
| G | POUNDS PER SQUARE INCH GAGE |
AAYT*AINTAKE CONNECTION QUANTITY
THE NUMBER OF INTAKE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYTA10*)
AAYU*DINTAKE CONNECTION TYPE
INDICATES THE TYPE OF INTAKE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYUDAG)
| Table 1 |
| Reply Code (AA84) | Reply |
| BK | COMPRESSION TUBE |
| BE | COUPLING HALF, QUICK DISCONNECT MALE |
| AB | FLARED TUBE |
| AD | OVAL FLANGE |
| AE | RECTANGULAR FLANGE |
| AF | ROUND FLANGE |
| BD | SOCKET WELD |
| AC | SOLDER TUBE |
| AG | SQUARE FLANGE |
| AJ | THREADED FEMALE |
| AK | THREADED MALE |
| BL | UNION NUT |
| BF | UNTHREADED FEMALE TAILPIECE |
| BM | UNTHREADED MALE |
AAYV*ADISCHARGE CONNECTION QUANTITY
THE NUMBER OF DISCHARGE CONNECTIONS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAYVA10*)
AAYW*DDISCHARGE CONNECTION TYPE
INDICATES THE TYPE OF DISCHARGE CONNECTION INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(AAYWDBL)
| Table 1 |
| Reply Code (AA84) | Reply |
| BK | COMPRESSION TUBE |
| BE | COUPLING HALF, QUICK DISCONNECT MALE |
| AB | FLARED TUBE |
| AD | OVAL FLANGE |
| AE | RECTANGULAR FLANGE |
| AF | ROUND FLANGE |
| BD | SOCKET WELD |
| AC | SOLDER TUBE |
| AG | SQUARE FLANGE |
| AJ | THREADED FEMALE |
| AK | THREADED MALE |
| BL | UNION NUT |
| BF | UNTHREADED FEMALE TAILPIECE |
| BM | UNTHREADED MALE |
CSFHJTEMP RATING PER FUNCTION
THE DEGREE OF HEAT OR COLD AS APPLIED TO THE FUNCTION OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSFHJCE2.0*;CSFHJCE2.0$$JCE2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AA88) | Reply |
| B | DISCHARGE |
| F | MINIMUM OPERATING |
| E | STEAM |
| D | SUCTION |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAGJ*;CBBLDAGH$$DFNY*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AGJ | FUNGUS RESISTANT TREATMENT |
| AGH | HEATING EQUIPMENT |
| FNY | ROHS DIRECTIVE COMPLIANCE |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJAC2.0*;AJAFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAA2.0*;AJAGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAB2.0*;AJAHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBPT*JUNPACKAGED UNIT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR ITEM,UNENCUMBERED BY PACKAGING OR PACKING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBPTJAB2.0*;BBPTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAG*;BBRGDAS$DAX*;BBRGDAS$$DAX*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AB | ABOVE GROUND MAGAZINE |
| AT | DOCK LEVEL HEATED WAREHOUSE |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AS | GROUND LEVEL HEATED WAREHOUSE |
| AW | GROUND LEVEL UNHEATED WAREHOUSE |
| AF | IGLOO MAGAZINE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AK | UNIMPROVED OPEN |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAE)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AE | FRAGILE |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAG1)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAC6)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ060)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ010 | CARBON DIOXIDE |
| HAZ060 | NATURAL GAS |
| HAZ039 | SULPHUR HEXAFLUORIDE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information