A valve designed to automatically maintain within close limits a predetermined outlet pressure which may be adjustable within a specified range regardless of the higher fluctuating or constant inlet pressure. It is designed for use with compressed gas(es) and various liquids and may include gauges. It may be inline or cartridge (manifold) design. Excludes:REGULATOR, PRESSURE, MEDICAL GAS ADMINISTRATION APPARATUS; REGULATOR, OXYGEN, BAROMETRIC CONTINUOUS FLOW; REGULATOR, OXYGEN DEMAND; REGULATOR, OXYGEN DILUTER DEMAND; and valve(1), fluid pressure regulating, aircraft.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED27565*)
AEVZJMAXIMUM INLET PRESSURE RATING
THE MAXIMUM PRESSURE OF THE MEDIA ON THE INLET SIDE AT WHICH AN ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVZJV2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AEWFDFILTER
AN INDICATION OF WHETHER OR NOT A FILTER IS INCLUDED.
Enter the applicable reply code from the table below
(AEWFDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ADQUDFLOW CONTROL DEVICE
THE PART THAT CONTROLS THE FLOW THROUGH THE ITEM.
Enter the applicable reply code from the table below
(ADQUDCQ*;ADQUDAC$DCW*;ADQUDAC$$DCW*)
| Table 1 |
| Reply Code (AC57) | Reply |
| AA | BALL |
| AB | BALL, PORTED |
| CT | BELLOWS |
| CV | BULB |
| AC | CONE |
| AD | CONE, BOTTOM GUIDED |
| AE | CONE, TOP GUIDED |
| AQ | DIAPHRAGM |
| BP | DISK |
| CL | DISK, BEVEL SEAT, BOTTOM GUIDED |
| CK | DISK, BEVEL SEAT, TOP GUIDED |
| AM | DISK, BOTTOM GUIDED |
| AF | DISK, CIRCULAR |
| AZ | DISK, DUAL |
| CM | DISK, DUAL, TOP GUIDED |
| AG | DISK, FLAT |
| AN | DISK, FLAT, BOTTOM GUIDED |
| AP | DISK, FLAT, TOP AND BOTTOM GUIDED |
| DE | DISK, FLAT, TOP GUIDED |
| CN | DISK, GUIDED |
| AH | DISK, PLUG TYPE |
| AJ | DISK, SOLID WEDGE |
| AK | DISK, SPLIT WEDGE |
| AR | DISK, SWING TYPE |
| AL | DISK, TOP GUIDED |
| CP | DOUBLE SEATED |
| DT | HANDWHEEL |
| AS | NEEDLE |
| CW | PISTON |
| CR | PISTON, BOTTOM GUIDED |
| AT | PISTON, FREE TYPE |
| CH | PISTON, SPRING LOADED |
| CQ | PISTON, TOP GUIDED |
| AU | PISTON, WEIGHTED TYPE |
| AV | PLUG |
| BD | PLUNGER |
| AW | POPPET |
| CS | POPPET, DUAL DISK |
| DS | SPRING |
| CG | STEM |
| AX | STEM AND INTEGRAL DISK |
ADQZAEND CONNECTION QUANTITY
THE NUMBER OF END CONNECTIONS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ADQZA10*)
IF STYLE/REPLY CODE(s) A4, A21, A22, A25, A28, A30 OR A31 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADQR)
IF STYLE/REPLY CODE(s) A6, A14, A15, A16, A17, A26, A27, A29, A35, A36, A37, A38, A41 OR A42 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ACSX)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLLA25)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1343 | A1 | STRAIGHT THRU |
| AAU1352 | A10 | STRAIGHT THRU |
| AAU1353 | A11 | TEE |
| AAU1354 | A12 | ANGLE |
| AAU1355 | A13 | TEE ANGLE |
| AAU1356 | A14 | ANGLE W/OFFSET |
| AAU1357 | A15 | TEE W/OFFSET |
| AAU1358 | A16 | ANGLE W/OFFSET |
| AAU1359 | A17 | TEE W/OFFSET |
| AAU1360 | A18 | STRAIGHT THRU |
| AAU1361 | A19 | CROSS |
| AAU1344 | A2 | TEE |
| AAU1362 | A20 | STRAIGHT THRU |
| AAU1363 | A21 | TEE ANGLE |
| AAU1364 | A22 | TEE |
| AAU1365 | A23 | ANGLE |
| AAU1366 | A24 | ANGLE |
| AAU1367 | A25 | ANGLE |
| AAU1368 | A26 | TEE ANGLE W/OFFSET |
| AAU1369 | A27 | TEE W/OFFSET |
| AAU1370 | A28 | ANGLE |
| AAU1371 | A29 | TEE W/OFFSET |
| AAU1345 | A3 | CROSS |
| AAU1372 | A30 | STRAIGHT THRU |
| AAU1373 | A31 | STRAIGHT THRU |
| AAU1374 | A32 | STRAIGHT THRU |
| AAU1375 | A33 | STRAIGHT THRU |
| AAU1376 | A34 | TEE W/OFFSET |
| AAU1377 | A35 | ANGLE W/OFFSET |
| AAU1378 | A36 | ANGLE W/OFFSET |
| AAU1379 | A37 | ANGLE W/OFFSET |
| AAU1380 | A38 | ANGLE W/OFFSET |
| AAU1381 | A39 | ANGLE |
| AAU1346 | A4 | STRAIGHT THRU |
| AAU1382 | A40 | ANGLE W/OFFSET |
| AAU1383 | A41 | TEE W/OFFSET |
| AAU1384 | A42 | ANGLE W/OFFSET |
| AAU1385 | A43 | STRAIGHT THRU |
| AAU1386 | A44 | ANGLE |
| AAU1387 | A45 | SCREW-IN CARTRIDGE |
| AAU1388 | A46 | DROP-IN CARTRIDGE |
| AAU1347 | A5 | Y ANGLE |
| AAU1348 | A6 | STRAIGHT THRU W/OFFSET |
| AAU1349 | A7 | ANGLE |
| AAU1350 | A8 | STRAIGHT THRU Y |
| AAU1351 | A9 | Y ANGLE |
AEVNDREGULATION TYPE
INDICATES THE BASIC DESIGN TYPE USED FOR REGULATING THE ITEM.
Enter the applicable reply code from the table below
(AEVNDL*;AEVNDB$DD*;AEVNDB$$DD*)
| Table 1 |
| Reply Code (AD45) | Reply |
| E | 1ST STAGE AUTOMATIC, 2ND STAGE MANUAL |
| F | 1ST STAGE MANUAL, 2ND STAGE AUTOMATIC |
| C | AUTOMATIC DOUBLE STAGE |
| A | AUTOMATIC OPERATION WITH HAND WHEEL OVERRIDE AT BOTTOM |
| B | AUTOMATIC SINGLE STAGE |
| M | MANUAL |
| D | MANUAL SINGLE STAGE |
| K | MANUAL, DOUBLE STAGE |
| L | SET POINT HAND WHEEL ADJUSTMENT AT TOP |
ACKLDMEDIA FOR WHICH DESIGNED
THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC MEDA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACKLDDD*;ACKLDCL$DDW*;ACKLDCL$$DDW*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AA | ACETYLENE |
| AB | AIR |
| AAJC | AIR, OIL PUMPED |
| AAJH | AIR, WATER PUMPED |
| AD | ALCOHOL, ETHYL |
| AE | ALCOHOL, METHYL |
| AG | AMMONIA, GASEOUS |
| AH | AMMONIA, LIQUID |
| AJ | ARGON |
| AAJD | ARGON, OIL PUMPED |
| AK | BROMOCHLOROMETHANE |
| AR | BUTANE |
| AS | CARBON DIOXIDE |
| DW | CARBON MONOXIDE |
| AT | CARBON TETRACHLORIDE |
| AV | CHLORINE |
| AAHT | DEUTERIUM |
| AACL | DICHLORODIFLUOROMETHANE |
| AGP | DIFLUOROMETHANE |
| AAHV | ETHANE |
| BB | ETHYLENE GLYCOL |
| ED | ETHYLENE OXIDE |
| AAHW | ETHYLENE, INDUSTRIAL |
| AAHX | ETHYLENE, MEDICAL |
| AAJF | FLUID, PETROLEUM BASE |
| AFE | FREON 12 USE REFRIGERANT R-12 |
| ADC | FREON USE REFRIGERANT |
| BD | GAS |
| AAJA | GAS, NONCORROSIVE |
| AADF | GENERAL |
| BL | HELIUM |
| AAJE | HELIUM, OIL PUMPED |
| AAHY | HEXAFLUOROETHANE |
| AAGJ | HYDRAULIC FLUID, MIL-H-5606 |
| AAGD | HYDRAULIC FLUID, PETROLEUM BASE |
| BN | HYDRAULIC FLUID, PHOSPHATE-ESTER BASE |
| BP | HYDRAULIC FLUID, SILICATE-ESTER BASE |
| BM | HYDRAULIC OIL |
| BQ | HYDRAZINE |
| BR | HYDRAZINE/UNSYMMETRIC DIMETHYL HYDRAZINE, 50/50- UDMH |
| BS | HYDROCARBON FUELS AND OILS |
| BT | HYDROGEN |
| BU | INGESTED LIQUIDS |
| NM | LIQUEFIED PETROLEUM GAS |
| GT | LIQUID, NONCORROSIVE |
| CD | LUBRICATING OIL, DIESTER BASE |
| AAJB | METHANE |
| HP | MONOCHLORODIFLUOROMETHANE |
| AADW | NATURAL GAS |
| CF | NITRIC ACID |
| CH | NITROGEN, GASEOUS |
| CJ | NITROGEN, LIQUID |
| AAHR | NITROGEN, OIL PUMPED |
| AAHS | NITROGEN, WATER PUMPED |
| AAEL | NITROUS OXIDE |
| AGQ | NONCORROSIVE FLUID |
| CL | OIL |
| CN | OXYGEN, GASEOUS |
| CP | OXYGEN, LIQUID |
| AGR | PETROLEUM BASE FLUID |
| CQ | PROPANE |
| AAW | REFRIGERANT R-22 |
| AAJG | REFRIGERANT, NONCORROSIVE |
| DC | STEAM |
| DD | SULPHUR DIOXIDE, GASEOUS |
| ABA | SULPHUR HEXAFLUORIDE |
| ET | SULPHUR HEXAFLUORIDE |
| DE | TRICHLORETHYLENE |
| DF | WATER |
| DH | WATER, FRESH |
| DK | WATER, OIL OR GAS |
| DL | WATER, SALT |
AEVRDVALVE LOADING METHOD
THE MEANS OF PROVIDING RESISTANCE TO THE MEDIA PASSING THROUGH A VALVE,WHEREBY THE VALVE IS ACTUATED TO REGULATE THE FLOW.
Enter the applicable reply code from the table below
(AEVRDJ*;AEVRDF$DG*;AEVRDF$$DG*)
| Table 1 |
| Reply Code (AC63) | Reply |
| G | ACTUATOR |
| F | BELLOWS |
| A | DIAPHRAGM |
| D | DOME |
| B | SPRING |
| H | STEM |
| J | THREADED STEM |
| K | THREADED STEM WITH SETSCREW |
| C | WEIGHT |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3BCMDST0303*;MATT3BCMDST0303$DST0630*;MATT3BCMDST0303$$DST0630*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3BAU | SEAT |
| 3BCM | FLOW CONTROL DEVICE |
| 3BKI | STEM |
| 3DLU | PACKING |
| 3DTD | BODY LINING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL1230 | ALUMINUM ALLOY 1230 |
| AL2011 | ALUMINUM ALLOY 2011 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL0029 | ALUMINUM ALLOY 360.0 |
| AL0031 | ALUMINUM ALLOY 380.0 |
| AL0054 | ALUMINUM ALLOY 383.0 |
| AL0032 | ALUMINUM ALLOY 384.0 |
| AL0027 | ALUMINUM ALLOY 413.0 |
| AL0044 | ALUMINUM ALLOY 443.0 |
| AL0050 | ALUMINUM ALLOY 518.0 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7075 | ALUMINUM ALLOY 7075 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| AL0052 | ALUMINUM ALLOY A360.0 |
| AL0028 | ALUMINUM ALLOY A380.0 |
| AL0030 | ALUMINUM ALLOY A413.0 |
| AL0060 | ALUMINUM ALLOY C355.0 |
| AL0008 | ALUMINUM ALLOY C443.0 |
| ASA000 | ASBESTOS |
| BRA000 | BRASS |
| BND000 | BRONZE |
| BNAAAA | BRONZE CAST |
| CDA000 | CADMIUM |
| CSA000 | CELLULOSE |
| CRA000 | CHROMIUM |
| CTB000 | COBALT ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU1026 | COPPER ALLOY 2.0401 |
| CU1038 | COPPER ALLOY 2.0966 |
| CU1020 | COPPER ALLOY 2.1020 |
| CU1016 | COPPER ALLOY 2.1030 |
| CU1039 | COPPER ALLOY 2.1050.01 |
| CU1043 | COPPER ALLOY 2.1090.01 |
| CU1017 | COPPER ALLOY 2.1096.01 |
| CU1046 | COPPER ALLOY 2.1504 |
| CU0074 | COPPER ALLOY 230 |
| CU0091 | COPPER ALLOY 360 |
| CU0092 | COPPER ALLOY 377 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0104 | COPPER ALLOY 511 |
| CU0632 | COPPER ALLOY 632 |
| CU0172 | COPPER ALLOY 836 |
| CU0180 | COPPER ALLOY 857 |
| CU0181 | COPPER ALLOY 861 |
| CU0182 | COPPER ALLOY 862 |
| CU0183 | COPPER ALLOY 863 |
| CU0195 | COPPER ALLOY 903 |
| CU0202 | COPPER ALLOY 922 |
| CU0214 | COPPER ALLOY 943 |
| CU0218 | COPPER ALLOY 953 |
| CUF000 | COPPER CAST |
| FBB001 | FABRIC, NYLON |
| FLR000 | FLUOROCARBON RUBBER |
| GFA000 | GRAPHITE |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| FEB000 | IRON CAST |
| FED000 | IRON CAST ALLOY |
| FE0022 | IRON CAST COMP 0.6025 |
| FE0178 | IRON CAST COMP 0.7040 |
| FE0063 | IRON CAST UNS F12102 |
| FE0047 | IRON CAST UNS F12801 |
| FE0080 | IRON CAST UNS F33101 |
| FEC000 | IRON MALLEABLE |
| FEG000 | IRON WROUGHT |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| NL0019 | NICKEL ALLOY 502 |
| NL0018 | NICKEL ALLOY K-500 |
| NL0017 | NICKEL ALLOY R-405 |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCE000 | PLASTIC ALKYD |
| PCAAD0 | PLASTIC FLUOROCARBON |
| PCJ000 | PLASTIC MELAMINE |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCDL00 | PLASTIC POLYAMIDE GLASS FILLED |
| PCQ000 | PLASTIC POLYCAPROLACTAM |
| PCT000 | PLASTIC POLYCHLOROTRIFLUOROETHYLENE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE |
| PCAM00 | PLASTIC POLYHEXAMETHYLENE AMIDE |
| PCCH00 | PLASTIC POLYIMIDE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAG00 | PLASTIC POLYTRIFLUOROCHLOROETHYLENE |
| PCAAAB | PLASTIC POLYUNDECANOAMIDE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCBM00 | PLASTIC POLYVINYL ACETATE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| RCE000 | RUBBER |
| RC0019 | RUBBER BUTADIENE-ACRYLONITRILE CLASS NBR |
| RC0022 | RUBBER BUTADIENE-STYRENE CLASS SBR |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RC0010 | RUBBER ETHYLENE-PROPYLENE-DIENE CLASS EPDM |
| RC0013 | RUBBER FLUOROCARBON CLASS FPM |
| RCS000 | RUBBER FLUOROSILICONE |
| RC0014 | RUBBER FLUOROSILICONE CLASS FQ |
| RCAC00 | RUBBER NEOPRENE |
| RC0012 | RUBBER POLYMETHYLENE-PERFLUOROALKYLENE CLASS FKM |
| RCZ000 | RUBBER POLYURETHANE |
| RCC000 | RUBBER SILICONE |
| RCB000 | RUBBER SYNTHETIC |
| SLK000 | SILICONE |
| STA000 | STEEL |
| ST1943 | STEEL COMP 1.0619 |
| ST0376 | STEEL COMP 1.0718 |
| ST0822 | STEEL COMP 1.4301 |
| ST0379 | STEEL COMP 1.4305 |
| ST2072 | STEEL COMP 1.4404 |
| ST0805 | STEEL COMP 1.4571 |
| ST0869 | STEEL COMP 1.7131 |
| ST1020 | STEEL COMP 1020 |
| ST1095 | STEEL COMP 1095 |
| ST1616 | STEEL COMP 10NC12 |
| ST1119 | STEEL COMP 1119 |
| ST1213 | STEEL COMP 1213 |
| ST0531 | STEEL COMP 150-125 |
| ST0202 | STEEL COMP 202 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0166 | STEEL COMP 303 PLUS X |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0305 | STEEL COMP 305 |
| ST0309 | STEEL COMP 309 |
| ST0310 | STEEL COMP 310 |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0321 | STEEL COMP 321 |
| ST0322 | STEEL COMP 322 |
| ST0324 | STEEL COMP 324 |
| ST0347 | STEEL COMP 347 |
| ST4012 | STEEL COMP 4012 |
| ST0403 | STEEL COMP 403 |
| ST0405 | STEEL COMP 405 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST0414 | STEEL COMP 414 |
| ST0416 | STEEL COMP 416 |
| ST0099 | STEEL COMP 416SE |
| ST0420 | STEEL COMP 420 |
| ST0430 | STEEL COMP 430 |
| ST0101 | STEEL COMP 430F |
| ST0172 | STEEL COMP 430FSE |
| ST0431 | STEEL COMP 431 |
| ST0105 | STEEL COMP 440A |
| ST0106 | STEEL COMP 440B |
| ST0107 | STEEL COMP 440C |
| ST0108 | STEEL COMP 440F |
| ST0285 | STEEL COMP 440FSE |
| ST0446 | STEEL COMP 446 |
| ST0124 | STEEL COMP 5160H |
| ST1726 | STEEL COMP 61S7 |
| ST0630 | STEEL COMP 630 |
| ST0633 | STEEL COMP 633 |
| ST0634 | STEEL COMP 634 |
| ST8620 | STEEL COMP 8620 |
| ST8740 | STEEL COMP 8740 |
| ST0030 | STEEL COMP E52100 |
| STB000 | STEEL CORROSION RESISTING |
| ST1099 | STEEL UNS J03002 |
| ST1593 | STEEL UNS J03007 |
| ST0594 | STEEL UNS J03008 |
| ST0603 | STEEL UNS J03504 |
| ST1123 | STEEL UNS J12072 |
| ST1836 | STEEL UNS J92200 |
| ST1169 | STEEL UNS J92600 |
| ST1177 | STEEL UNS J92710 |
| ST1180 | STEEL UNS J92900 |
| ST1004 | STEEL UNS K11564 |
| ST0532 | STEEL UNS K24065 |
| TTA000 | TITANIUM ALLOY |
| TNB000 | TUNGSTEN CARBIDE |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
| ZN0004 | ZINC ALLOY 925 |
| ZN0015 | ZINC ALLOY UNS Z33520 |
| ZN0018 | ZINC ALLOY UNS Z35531 |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3BAU | SEAT |
| 3BCM | FLOW CONTROL DEVICE |
| 3BKI | STEM |
| 3DLU | PACKING |
| 3DTD | BODY LINING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDPCF000*;SFTT3AEEDPCF000$DXXB000*;SFTT3AEEDPCF000$$DXXB000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3AUW | OUTSIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUB000 | COPPER ALLOY |
| DCC000 | DICHROMATE ZINC |
| ENA000 | ENAMEL |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PHB000 | PHOSPHATE IRON |
| PCS000 | PLASTIC EPOXY |
| PCF000 | PLASTIC POLYAMIDE |
| PRA000 | PRIMER |
| SNA000 | TIN |
| VAA000 | VARNISH |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3AUW | OUTSIDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
AEWB*JOUTLET PRESSURE ACCURACY RATING
THE RATED VARIANCE OF THE OUTLET PRESSURE FROM THE SET PRESSURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWBJV2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY*;CBBLDFNY$$DFNY*)
| Table 1 |
| Reply Code (AN47) | Reply |
| FNY | ROHS DIRECTIVE COMPLIANCE |
AZKQ*JTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Tables 1 and 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples. For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.
(AZKQJFA68.0*; AZKQJCB0.0$$JCC35.0*; AZKQJFCM15.0*; AZKQJFBM40.0$$JFC75.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEWA*JOUTLET PRESSURE SETTING
THE SET /NONADJUSTABLE/ PRESSURE OF THE MEDIA ON THE OUTLET SIDE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWAJV2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AEVA*JOUTLET PRESSURE RANGE
THE MINIMUM TO MAXIMUM LIMITS OF OUTLET PRESSURE OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AEVAJKM32.0/P50.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJLC2.0*;ABMKJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CYDY*AVALVE MODEL NUMBER FOR WHICH DESIGNED
THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE VALVE FOR WHICH THE ITEM IS DESIGNED.
Enter the alpha-numeric reply with a minimum of one character.
(CYDYAA0)
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDYY*;ABFFDCDM$DCEB*;ABFFDCDM$$DCEB*)
| Table 1 |
| Reply Code (AB28) | Reply |
| CN | ADAPTER |
| YP | ADJUSTMENT STEM |
| CP | AUTOMATIC RELIEF VALVE |
| YT | BONNET |
| YK | BRAZING RING |
| YR | CRANK |
| CQ | CYLINDER GAGE |
| CR | DELIVERY GAGE |
| YZ | DIAL |
| CDJ | DRAIN COCK |
| YQ | DUMP VALVE |
| CDK | ELBOW END CONNECTOR |
| CS | EXTERNAL PILOT VALVE |
| CDL | EXTERNAL SENSING LINE |
| CT | FLOWMETER |
| CDM | GAUGE |
| YV | INDICATOR |
| YL | INLET ADAPTER |
| CU | INLET PRESSURE GAGE |
| YM | INLET STRAINER |
| YN | INTERNAL BYPASS VALVE |
| CV | INTERNAL PILOT VALVE |
| ZA | LEVER HANDLE |
| BAD | MOUNTING HARDWARE |
| CW | NEEDLE VALVE |
| ED | NUT |
| EE | NUT AND SLEEVE |
| CX | OUTLET PRESSURE GAGE |
| AFR | PANEL MOUNTING BRACKET |
| AQQ | PIPE PLUG |
| BZR | PITOT TUBE |
| AEA | PLUG |
| AFE | PREINSERTED BRAZING RING |
| CY | PRESSURE BREAKER |
| CDY | PRESSURE GAUGE |
| AFS | PUSHBUTTON CLEANING RESTRICTION |
| YW | STRAINER |
| CEA | SUB PLATE |
| YX | TAILPIECE |
| AFQ | TAILPIECE W/GROOVES |
| CDZ | TAMPER PROOF CAP |
| CZ | TEMPERATURE GAGE |
| CC | THERMOMETER |
| CEB | TREADLE |
| YY | UNION NUT |
| CBT | VALVE CAP |
| YS | WRENCH |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CCFG*JVALVE SIZE
DESIGNATES THE SIZE OF THE VALVE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CCFGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
BZRS*GEND CONNECTION SPEC/STD
THE SPECIFICATION AND/OR STANDARD OF THE END CONNECTION.
Enter clear text.
(BZRSGCLEARTEXT)
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLH and ACLL and ACLK and THDS) or (ACKN and ACLH and ACLL and ADRN and THDS)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLH)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLL and THDS)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLG)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACKT)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLE and ADRN and ACLL and THDS)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLE and ACLF)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLF and ADRN and ACLL and THDS)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLF)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ADRN and ACLL and THDS)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLL and ACLK and THDS) or (ACKN and ACLL and ADRN and THDS)
IF STYLE/REPLY CODE(s) WY OR WZ WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (THDS)
ACKM*DFIRST END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACKMDAQ)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AAD | FLANGED |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
IF STYLE/REPLY CODE(s) G3, G4, G5 OR G6 WERE ENTERED FOR MRC ACKN, YOU MUST ANSWER MRC (ACKP and ACKQ)
IF STYLE/REPLY CODE(s) G7, G8 OR G9 WERE ENTERED FOR MRC ACKN, YOU MUST ANSWER MRC (ACKR and ACKS)
ACKN*LFIRST END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACKNLE7)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAT |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
| AAU1449 | G3 | RAISED |
| AAU1450 | G4 | RAISED |
| AAU1451 | G5 | RAISED |
| AAU1452 | G6 | SWIVEL FLANGE RAISED |
| AAU1453 | G7 | RECESSED W/GASKET GROOVE |
| AAU1454 | G8 | RECESSED |
| AAU1455 | G9 | RECESSED |
ACKP*JFIRST END RAISED FACE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKPJAC2.0*;ACKPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKQ*JFIRST END RAISED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKQJAB2.0*;ACKQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKR*JFIRST END RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKRJAA2.0*;ACKRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKS*JFIRST END RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKSJAB2.0*;ACKSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKY and ACLA and ACLB and ACKZ)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (AAHF and ACKU and ACLA and ACLB and ACKZ)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW and ACLA and AFLN and AFLS and ACKZ)
IF STYLE/REPLY CODE(s) 1A OR 2A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKY)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (AAHF and ACKU)
IF STYLE/REPLY CODE(s) 4A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW)
IF STYLE/REPLY CODE(s) 6A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW and ACKX)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKZ and ACKU and ACKV and ACKW and ACLA and ACLB)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKZ and ACKU and ACKV and ACKX and ACLA and ACLB)
ACKT*LFIRST END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACKTL5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02898 | 1 | HEXAGON W/ BOLT HOLES |
| DR02899 | 1A | HEXAGON |
| DR02906 | 2 | OCTAGON W/ BOLT HOLES |
| DR02907 | 2A | OCTAGON |
| DR02914 | 3 | ROUND W/ BOLT HOLES |
| DR02915 | 3A | ROUND |
| DR02922 | 4 | RECTANGULAR (INCLUDES SQUARE) W/ BOLT HOLES |
| DR02923 | 4A | RECTANGULAR (INCLUDES SQUARE) |
| DR02924 | 5 | TRIANGULAR W/ BOLT HOLES |
| DR02925 | 5A | TRIANGULAR |
| DR02932 | 6 | OVAL W/ BOLT HOLES |
| DR02933 | 6A | OVAL |
ACKZ*AFIRST END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACKZA10*)
AAHF*JFIRST END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHFJAA2.0*;AAHFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKU*JFIRST END FLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FIRST END FLANGE, IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKUJAC2.0*;ACKUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKV*JFIRST END FLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END FLANGE, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKVJAA2.0*;ACKVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKW*JFIRST END FLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FIRST END FLANGE, IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKWJAB2.0*;ACKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKX*JFIRST END FLANGE END RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKXJAC2.0*;ACKXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKY*JFIRST END WIDTH ACROSS FLATS
THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE FIRST END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKYJAB2.0*;ACKYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLA*JFIRST END BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLAJAB2.0*;ACLAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLB*JFIRST END BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLBJAC2.0*;ACLBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLN*JFIRST END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLNJAC2.0*;AFLNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLS*JFIRST END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLSJAA2.0*;AFLSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLE*JFIRST END INSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLEJAA2.0*;ACLEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLF*JFIRST END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLFJAB2.0*;ACLFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLG*JFIRST END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACLH*JFIRST END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLHJAC2.0*;ACLHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLK*AFIRST END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACLKAE5)
ADRN*JFIRST END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRNJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACLL*DFIRST END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(ACLL3AATDR*;ACLL3AATDR$DL*;ACLL3AATDR$$DL*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTE*BFIRST END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTEB2.0)
ACTK*JFIRST END SEAT RADIUS
THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACTKJAA2.0*;ACTKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) F WERE ENTERED FOR MRC ACLR, YOU MUST ANSWER MRC (ACLS)
ACLR*DSECOND END RELATIONSHIP WITH FIRST END
INDICATES WHETHER OR NOT THE SECOND END IS IDENTICAL TO THE FIRST END. PLEASE USE MRC CQBB IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACLRDB)
| Table 1 |
| Reply Code (AB78) | Reply |
| B | IDENTICAL |
| F | NOT IDENTICAL |
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMP and ACMS and ACMR and THDS) or (ACLT and ACMP and ACMS and ADRP and THDS)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMP)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMS and THDS)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMN)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACLY)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACML and ADRP and ACMS and THDS)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACML and ACMM)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMM and ADRP and ACMS and THDS)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMM)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ADRP and ACMS and THDS)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMS and ACMR and THDS) or (ACLT and ACMS and ADRP and THDS)
IF STYLE/REPLY CODE(s) WY OR WZ WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (THDS)
ACLS*DSECOND END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACLSDBE)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
IF STYLE/REPLY CODE(s) G3, G4, G5 OR G6 WERE ENTERED FOR MRC ACLT, YOU MUST ANSWER MRC (ACLU and ACLV)
IF STYLE/REPLY CODE(s) G7, G8 OR G9 WERE ENTERED FOR MRC ACLT, YOU MUST ANSWER MRC (ACLW and ACLX)
ACLT*LSECOND END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACLTLC1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAL |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
| AAU1449 | G3 | RAISED |
| AAU1450 | G4 | RAISED |
| AAU1451 | G5 | RAISED |
| AAU1452 | G6 | SWIVEL FLANGE RAISED |
| AAU1453 | G7 | RECESSED W/GASKET GROOVE |
| AAU1454 | G8 | RECESSED |
| AAU1455 | G9 | RECESSED |
ACLU*JSECOND END RAISED FACE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLUJAA2.0*;ACLUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLV*JSECOND END RAISED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLVJAC2.0*;ACLVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLW*JSECOND END RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLWJAB2.0*;ACLWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLX*JSECOND END RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLXJAC2.0*;ACLXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMD and ACMG and ACMH and ACMF)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (AAHV and ACLZ and ACMG and ACMH and ACMF)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMA and ACMB and ACMG and AFLP and AFLT and ACMF)
IF STYLE/REPLY CODE(s) 1A OR 2A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMD)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (AAHV and ACLZ)
IF STYLE/REPLY CODE(s) 4A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMA and ACMB)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMA and ACMB)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACMF and ACLZ and ACMA and ACMB and ACMG and ACMH)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACMF and ACLZ and ACMA and ACMB and ACMG and ACMH)
ACLY*LSECOND END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACLYL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02898 | 1 | HEXAGON W/ BOLT HOLES |
| DR02899 | 1A | HEXAGON |
| DR02906 | 2 | OCTAGON W/ BOLT HOLES |
| DR02907 | 2A | OCTAGON |
| DR02914 | 3 | ROUND W/ BOLT HOLES |
| DR02915 | 3A | ROUND |
| DR02923 | 4 | RECTANGULAR (INCLUDES SQUARE) W/ BOLT HOLES |
| DR02922 | 4A | RECTANGULAR (INCLUDES SQUARE) |
| DR02924 | 5 | TRIANGULAR W/ BOLT HOLES |
| DR02925 | 5A | TRIANGULAR |
| DR02932 | 6 | OVAL W/ BOLT HOLES |
ACMF*ASECOND END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACMFA10*)
AAHV*JSECOND END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHVJAB2.0*;AAHVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLZ*JSECOND END FLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SECOND END FLANGE, IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLZJAA2.0*;ACLZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMA*JSECOND END FLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END FLANGE, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMAJAA2.0*;ACMAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMB*JSECOND END FLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SECOND END FLANGE, IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMBJAA2.0*;ACMBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMD*JSECOND END WIDTH ACROSS FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMDJAB2.0*;ACMDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMG*JSECOND END BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMGJAC2.0*;ACMGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMH*JSECOND END BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMHJAA2.0*;ACMHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLP*JSECOND END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLPJAB2.0*;AFLPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLT*JSECOND END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLTJAB2.0*;AFLTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACML*JSECOND END INSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMLJAB2.0*;ACMLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMM*JSECOND END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMMJAB2.0*;ACMMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMN*JSECOND END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMNJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACMP*JSECOND END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMPJAA2.0*;ACMPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMR*ASECOND END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACMRAM0)
ADRP*JSECOND END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRPJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACMS*DSECOND END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACMSDL*;ACMSDR$DL*;ACMSDR$$DL*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTF*BSECOND END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CRCN OR CQRB WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTFB2.0)
ACTL*JSECOND END SEAT RADIUS
THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACTLJAC2.0*;ACTLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) G WERE ENTERED FOR MRC ACMX, YOU MUST ANSWER MRC (ACMY)
ACMX*DTHIRD END RELATIONSHIP WITH PRECEDING ENDS
INDICATES WHETHER OR NOT THE THIRD END IS IDENTICAL WITH FIRST OR SECOND END.
Enter the applicable reply code from the table below
(ACMXDD)
| Table 1 |
| Reply Code (AB78) | Reply |
| C | IDENTICAL WITH FIRST END |
| D | IDENTICAL WITH SECOND END |
| G | NOT IDENTICAL WITH FIRST OR SECOND END |
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNW and ACNZ and ACNY and THDS) or (ACMZ and ACNW and ACNZ and ADRQ and THDS)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNW)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNZ and THDS)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNV)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNF)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ADRQ and ACNZ and THDS)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNU)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNU and ADRQ and ACNZ and THDS)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNU)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ADRQ and ACNZ and THDS)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNZ and ACNY and THDS) or (ACMZ and ACNZ and ADRQ and THDS)
IF STYLE/REPLY CODE(s) WY OR WZ WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (THDS)
ACMY*DTHIRD END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACMYDAV)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
ACMZ*LTHIRD END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACMZLD7)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAL |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMPRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
| AAU1449 | G3 | RAISED |
| AAU1450 | G4 | RAISED |
| AAU1451 | G5 | RAISED |
| AAU1452 | G6 | SWIVEL FLANGE RAISED |
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNG and ACNH and ACNP and ACNQ and ACNN)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK and ACNP and AFLQ and AFLU and ACNN)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNG and ACNH)
IF STYLE/REPLY CODE(s) 4A WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK and ACNP and ACNQ)
ACNF*LTHIRD END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACNFL4A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02899 | 1A | HEXAGON |
| DR02907 | 2A | OCTAGON |
| DR02914 | 3 | ROUND W/ BOLT HOLES |
| DR02915 | 3A | ROUND |
| DR02922 | 4 | RECTANGULAR (INCLUDES SQUARE) W/ BOLT HOLES |
| DR02923 | 4A | RECTANGULAR (INCLUDES SQUARE) |
| DR02924 | 5 | TRIANGULAR W/ BOLT HOLES |
| DR02925 | 5A | TRIANGULAR |
ACNN*ATHIRD END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACNNA10*)
ACNG*JTHIRD END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNGJAB2.0*;ACNGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNH*JTHIRD END FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNHJAC2.0*;ACNHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNK*JTHIRD END FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNKJAC2.0*;ACNKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNP*JTHIRD END BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNPJAA2.0*;ACNPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNQ*JTHIRD END BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNQJAA2.0*;ACNQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLQ*JTHIRD END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLQJAC2.0*;AFLQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLU*JTHIRD END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLUJAB2.0*;AFLUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNU*JTHIRD END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNUJAB2.0*;ACNUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNV*JTHIRD END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNVJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACNW*JTHIRD END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNWJAC2.0*;ACNWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNY*ATHIRD END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACNYAA7)
ADRQ*JTHIRD END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRQJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACNZ*DTHIRD END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. PLEASE USE MRC AAJF WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACNZDL*;ACNZDR$DL*;ACNZDR$$DL*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTG*BTHIRD END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTGB2.0)
IF STYLE/REPLY CODE(s) H WERE ENTERED FOR MRC ACPE, YOU MUST ANSWER MRC (ACPF)
ACPE*DFOURTH END RELATIONSHIP WITH PRECEDING ENDS
INDICATES WHETHER OR NOT THE FOURTH END IS IDENTICAL WITH THE FIRST,SECOND,OR THIRD END.
Enter the applicable reply code from the table below
(ACPEDH)
| Table 1 |
| Reply Code (AB78) | Reply |
| C | IDENTICAL WITH FIRST END |
| D | IDENTICAL WITH SECOND END |
| E | IDENTICAL WITH THIRD END |
| H | NOT IDENTICAL WITH FIRST, SECOND OR THIRD END |
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQC and ACQF and ACQE and THDS) or (ACPG and ACQC and ACQF and THDS)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and THDS)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF and THDS)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQB)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACPM)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF and THDS)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQA)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQA and ACQF and THDS)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQA)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF and THDS)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF and ACQE and THDS) or (ACPG and ACQF and THDS)
ACPF*DFOURTH END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACPFDBD)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
ACPG*LFOURTH END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACPGLD6)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAT |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMPRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACPM, YOU MUST ANSWER MRC (ACPV and AFLR and AFLV and ACPU)
ACPM*LFOURTH END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACPML4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02899 | 4 | RECTANGULAR W/BOLT HOLES |
ACPU*AFOURTH END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACPUA10*)
ACPV*JFOURTH END BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACPVJAA2.0*;ACPVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLR*JFOURTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLRJAC2.0*;AFLRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLV*JFOURTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLVJAA2.0*;AFLVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACQA*JFOURTH END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACQAJAB2.0*;ACQAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACQB*JFOURTH END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACQBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACQC*JFOURTH END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACQCJAA2.0*;ACQCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACQE*AFOURTH END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACQEAB6)
ACQF*DFOURTH END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. PLEASE USE MRC AAJF WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACQFDR*;ACQFDL$DR*;ACQFDL$$DR*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTH*BFOURTH END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTHB2.0)
ADQL*JFACE TO FACE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQLJAC2.0*;ADQLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQM*JFIRST CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQMJAA2.0*;ADQMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQN*JSECOND CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQNJAC2.0*;ADQNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQP*JTHIRD CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQPJAA2.0*;ADQPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQQ*JFOURTH CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQQJAA2.0*;ADQQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQR*JCENTER TO CENTER DISTANCE
THE CENTER TO CENTER DISTANCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQRJAC2.0*;ADQRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACSX*JOFFSET DISTANCE
THE DISTANCE OF OFFSET IN THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACSXJAB2.0*;ACSXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADZJ*DMOUNTING FACILITY
THE MEANS OTHER THAN THE END CONNECTION/S/ BY WHICH THE ITEM MAY BE MOUNTED.
Enter the applicable reply code from the table below
(ADZJDG*;ADZJDJ$DH*;ADZJDJ$$DH*)
| Table 1 |
| Reply Code (AC70) | Reply |
| K | BOLTS |
| F | BRACKET |
| B | CLAMP |
| H | EXTERNAL THREAD |
| G | FLANGE |
| J | INTERNAL THREAD |
| D | LUG |
| E | PANEL |
| L | STUD |
ADZH*DRENEWABLE SEAT RING TYPE
INDICATES THE TYPE OF RENEWABLE SEATING RING IN THE ITEM.
Enter the applicable reply code from the table below
(ADZHDAD*;ADZHDAF$DAL*;ADZHDAF$$DAL*)
| Table 1 |
| Reply Code (AC69) | Reply |
| A | ANY ACCEPTABLE |
| AA | BOLTED |
| AB | BONDED |
| AC | PRESSED-IN |
| AL | RETAINING RING |
| AD | RETAINING SCREW |
| AE | THREADED |
| AF | WELDED |
AEVP*DMANUAL CONTROL METHOD
THE MEANS USED TO MANUALLY ADJUST THE ITEM.
Enter the applicable reply code from the table below
(AEVPDAR*;AEVPDAT$DAU*;AEVPDAT$$DAU*)
| Table 1 |
| Reply Code (AC58) | Reply |
| BK | KNOB |
| AH | LEVER |
| AAJR | LEVER W/WEIGHTS |
| AU | SCREW |
| AR | TEE HANDLE |
| AV | WHEEL |
| AT | WRENCH |
AEVQ*DVALVE STEM DESIGN
THE SEAT DESIGN OF THE VALVE STEM.
Enter the applicable reply code from the table below
(AEVQDB*;AEVQDC$DC*)
| Table 1 |
| Reply Code (AD46) | Reply |
| B | DOUBLE SEAT |
| C | SINGLE SEAT |
AEVS*DREMOTE ACTUATION METHOD
THE MEANS WHEREBY A VALVE IS ACTUATED OTHER THAN BY THE MEDIA PASSING THROUGH IT.
Enter the applicable reply code from the table below
(AEVSDK*;AEVSDL$DM*;AEVSDL$$DM*)
| Table 1 |
| Reply Code (AD04) | Reply |
| J | BELLOWS |
| B | DIAPHRAGM |
| D | PISTON |
| M | PNEUMATIC |
| F | ROTARY PISTON |
| K | SOLENOID |
| L | SPOOL |
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
THDS*JTHREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(THDS3IARJBU2.0*;THDS3IARJBU2.0$JBU2.0*;THDS3IARJBU2.0$$JBU2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIB | THIRD END |
| 3AIC | FOURTH END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3IAR | FIRST END BODY |
| 3IAS | FIRST END BODY LINING |
| Table 2 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BU | BRITISH STANDARD PIPE PARALLEL |
| BR | BSP.TR INT |
| SM | ISO M |
| NG | NGO |
| GT | NGT |
| SP | NPS |
| SF | NPSF |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| SW | SAE |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| NS | UNS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information