A hinge usually with rectangularly shaped leaves. The dimension parallel to the hinge pin must be greater than the dimension transverse to the hinge pin. It may have a tension coil spring at its pivot(s) for closing action, and may have a third member between its pivot(s) to permit the door, or the like, to swing in an arc from either side.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED22894*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3ACKDAL2024*;MATT3ACKDAL2024$DFEC000*;MATT3ACKDAL2024$$DFEC000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ADT | SPRING |
| 3AEE | OVERALL |
| 3AZT | PIN |
| 3DPT | BALL BEARING |
| 3DQR | LEAF |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3ICH | BUTTON TIP |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1230 | ALUMINUM ALLOY 1230 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0213 | ALUMINUM ALLOY 213.0 |
| AL3003 | ALUMINUM ALLOY 3003 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL5005 | ALUMINUM ALLOY 5005 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL0059 | ALUMINUM ALLOY 535.0 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6062 | ALUMINUM ALLOY 6062 |
| AL7072 | ALUMINUM ALLOY 7072 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0074 | COPPER ALLOY 230 |
| CU0076 | COPPER ALLOY 240 |
| CU0079 | COPPER ALLOY 260 |
| CU0304 | COPPER ALLOY 262 |
| CU0080 | COPPER ALLOY 268 |
| CU0081 | COPPER ALLOY 270 |
| CU0272 | COPPER ALLOY 272 |
| CU0274 | COPPER ALLOY 274 |
| CU0302 | COPPER ALLOY 280 |
| CU0330 | COPPER ALLOY 330 |
| CU0305 | COPPER ALLOY 331 |
| CU0332 | COPPER ALLOY 332 |
| CU0335 | COPPER ALLOY 335 |
| CU0340 | COPPER ALLOY 340 |
| CU0088 | COPPER ALLOY 342 |
| CU0306 | COPPER ALLOY 344 |
| CU0307 | COPPER ALLOY 345 |
| CU0308 | COPPER ALLOY 347 |
| CU0309 | COPPER ALLOY 348 |
| CU0310 | COPPER ALLOY 350 |
| CU0089 | COPPER ALLOY 353 |
| CU0090 | COPPER ALLOY 356 |
| CU0091 | COPPER ALLOY 360 |
| CU0370 | COPPER ALLOY 370 |
| CU0092 | COPPER ALLOY 377 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0465 | COPPER ALLOY 465 |
| CU0466 | COPPER ALLOY 466 |
| CU0467 | COPPER ALLOY 467 |
| CU0100 | COPPER ALLOY 482 |
| CU0101 | COPPER ALLOY 485 |
| CU0675 | COPPER ALLOY 675 |
| CU0182 | COPPER ALLOY 862 |
| CU0183 | COPPER ALLOY 863 |
| CU0184 | COPPER ALLOY 864 |
| CU0185 | COPPER ALLOY 865 |
| PCU000 | GLASS REINFORCED PLASTIC |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| FEC000 | IRON MALLEABLE |
| FEG000 | IRON WROUGHT |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAH00 | PLASTIC POLYURETHANE |
| RCB000 | RUBBER SYNTHETIC |
| AA0002 | ST8770 STEEL, QQ-S-698, COND CR, TEMPER 4 |
| AA0003 | ST8771 STEEL, QQ-S-698, COND HRCQ |
| STA000 | STEEL |
| ST0822 | STEEL COMP 1.4301 |
| ST1006 | STEEL COMP 1006 |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1010 | STEEL COMP 1010 |
| ST1011 | STEEL COMP 1011 |
| ST1012 | STEEL COMP 1012 |
| ST1013 | STEEL COMP 1013 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1022 | STEEL COMP 1022 |
| ST1025 | STEEL COMP 1025 |
| ST1030 | STEEL COMP 1030 |
| ST1033 | STEEL COMP 1033 |
| ST1034 | STEEL COMP 1034 |
| ST1035 | STEEL COMP 1035 |
| ST1038 | STEEL COMP 1038 |
| ST1040 | STEEL COMP 1040 |
| ST1108 | STEEL COMP 1108 |
| ST1109 | STEEL COMP 1109 |
| ST1110 | STEEL COMP 1110 |
| ST1137 | STEEL COMP 1137 |
| ST1524 | STEEL COMP 1524 |
| ST1527 | STEEL COMP 1527 |
| ST1541 | STEEL COMP 1541 |
| ST0159 | STEEL COMP 203EZ |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0180 | STEEL COMP 302B |
| ST0303 | STEEL COMP 303 |
| ST0166 | STEEL COMP 303 PLUS X |
| ST0157 | STEEL COMP 303CU |
| ST0165 | STEEL COMP 303MA |
| ST0158 | STEEL COMP 303PB |
| ST0078 | STEEL COMP 303S |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0448 | STEEL COMP 304H |
| ST0080 | STEEL COMP 304L |
| ST0449 | STEEL COMP 304N |
| ST0305 | STEEL COMP 305 |
| ST0152 | STEEL COMP 308 |
| ST0309 | STEEL COMP 309 |
| ST0153 | STEEL COMP 309S |
| ST0492 | STEEL COMP 309S-CB |
| ST0310 | STEEL COMP 310 |
| ST0154 | STEEL COMP 310S |
| ST0155 | STEEL COMP 314 |
| ST0316 | STEEL COMP 316 |
| ST0354 | STEEL COMP 316F |
| ST0450 | STEEL COMP 316H |
| ST0082 | STEEL COMP 316L |
| ST0451 | STEEL COMP 316N |
| ST0317 | STEEL COMP 317 |
| ST0254 | STEEL COMP 317L |
| ST0321 | STEEL COMP 321 |
| ST0452 | STEEL COMP 321H |
| ST0322 | STEEL COMP 322 |
| ST0323 | STEEL COMP 323 |
| ST0324 | STEEL COMP 324 |
| ST0616 | STEEL COMP 325 |
| ST0490 | STEEL COMP 329 |
| ST0617 | STEEL COMP 330 |
| ST0618 | STEEL COMP 330A |
| ST0347 | STEEL COMP 347 |
| ST0453 | STEEL COMP 347H |
| ST0348 | STEEL COMP 348 |
| ST0640 | STEEL COMP 348H |
| ST0384 | STEEL COMP 384 |
| ST0385 | STEEL COMP 385 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST4140 | STEEL COMP 4140 |
| ST0416 | STEEL COMP 416 |
| ST0255 | STEEL COMP 416 PLUS X |
| ST0099 | STEEL COMP 416SE |
| ST0420 | STEEL COMP 420 |
| ST0100 | STEEL COMP 420F |
| ST0284 | STEEL COMP 420FSE |
| ST0430 | STEEL COMP 430 |
| ST0101 | STEEL COMP 430F |
| ST0172 | STEEL COMP 430FSE |
| ST4340 | STEEL COMP 4340 |
| ST0105 | STEEL COMP 440A |
| ST0630 | STEEL COMP 630 |
| ST0163 | STEEL COMP M1020 |
| ST0704 | STEEL COMP XM-12 |
| ST0187 | STEEL COMP XM-13 |
| ST9851 | STEEL COMP XM-34 |
| STB000 | STEEL CORROSION RESISTING |
| ST0668 | STEEL UNS K08500 |
| ST1014 | STEEL UNS K31545 |
| AAA012 | THERMOPLASTIC |
| TTA000 | TITANIUM ALLOY |
| ZNB000 | ZINC |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ADT | SPRING |
| 3AEE | OVERALL |
| 3AZT | PIN |
| 3DPT | BALL BEARING |
| 3DQR | LEAF |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3ICH | BUTTON TIP |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AKES, YOU MUST ANSWER MRC (AKET)
AKESDPIN REMOVABILITY
AN INDICATION OF WHETHER OR NOT THE PIN IS REMOVABLE.
Enter the applicable reply code from the table below
(AKESDC*;AKESDB$DB*)
| Table 1 |
| Reply Code (AC29) | Reply |
| C | NONREMOVABLE |
| B | REMOVABLE |
AKET*DRISING PIN
AN INDICATION OF WHETHER OR NOT A RISING PIN IS INCLUDED.
Enter the applicable reply code from the table below
(AKETDC*;AKETDB$DC*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AJNCDREVERSIBLE FEATURE
AN INDICATION OF WHETHER OR NOT A REVERSIBLE FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(AJNCDB*;AJNCDC$DC*)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
AKEXAKNUCKLE QUANTITY
THE NUMBER OF CYLINDRICAL PROJECTIONS THROUGH WHICH AN AXIS OR PIN PASSES.
Enter the numeric reply with a minimum of one digit.
(AKEXA10*)
AGLDDPERFORMANCE TYPE
INDICATES THE PERFORMANCE CAPABILITY OF THE ITEM OR COMPONENT.
Enter the applicable reply code from the table below
(AGLDDN)
| Table 1 |
| Reply Code (AE89) | Reply |
| AL | EXTRA HEAVY DUTY |
| AK | HEAVY DUTY |
| AB | LIGHT DUTY |
| AF | MEDIUM DUTY |
| N | NOT RATED |
| BA | REGULAR DUTY |
| BZ | STANDARD LOAD |
IF STYLE/REPLY CODE(s) 10, 11, 12, 13, 14, 15, 16, 31, 32, 33, 34, 35 OR 36 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ADAT and AKFK and ABPX)
IF STYLE/REPLY CODE(s) 20, 21, 22, 37 OR 38 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ADAT and AKFK and ABPX)
IF STYLE/REPLY CODE(s) 17 OR 23 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ABPX and AKFK and ADAT)
IF STYLE/REPLY CODE(s) 18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and AKFK and ABVV and ABPX)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and AKFK and ABVV and ABPX and ABTB)
IF STYLE/REPLY CODE(s) 24 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPX and ADAT and ABTB and AKFK and AKFV and AKFR)
IF STYLE/REPLY CODE(s) 25, 27 OR 29 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPX and ADAT and ABTB and AKFQ and AKFT and AKFK)
IF STYLE/REPLY CODE(s) 26 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPX and ADAT and ABTB and AKFQ and AKFT and AKFV and AKFR)
IF STYLE/REPLY CODE(s) 28 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPX and ADAT and ABTB and AKFQ and AKFT and AKFV and AKFR)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPX and ADAT and ABTB and AKFR and AKFK and AKFV)
IF STYLE/REPLY CODE(s) 45 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFJ and AKFH and AKFK and ABHP and AKFS and ABPX)
IF STYLE/REPLY CODE(s) 46 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFJ and AKFH and ABTB and ABHP and AKFK and ADFY and AKFS and ABPX)
IF STYLE/REPLY CODE(s) 47 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFJ and AKFF and AKFH and ABTB and ABHP and AKFK and ADFY and AKFS and ABPX)
IF STYLE/REPLY CODE(s) 48 OR 51 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFH and AKFK and ABHP and AKFS and ABPX)
IF STYLE/REPLY CODE(s) 49 OR 52 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFH and ABTB and ABHP and AKFK and ADFY and AKFS and ABPX)
IF STYLE/REPLY CODE(s) 50 OR 53 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFH and ABTB and AKFF and ABHP and AKFK and ADFY and AKFS and ABPX)
IF STYLE/REPLY CODE(s) 60, 61 OR 62 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ADAT and AKFK and ABPX)
IF STYLE/REPLY CODE(s) 63 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAT and AKFK and ABTB and AKFV and ABPX and AKFR)
IF STYLE/REPLY CODE(s) 64 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAT and AKFT and AKFV and ABTB and ABPX and AKFQ)
IF STYLE/REPLY CODE(s) 68, 69, 71, 72, 73, 74 OR 75 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFL and ABTB and AKFM and AKFN and AKFP and ABPX)
IF STYLE/REPLY CODE(s) 70 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFV and AKFL and ABPX and AKFM and ABTB and AKFN and AKFR)
IF STYLE/REPLY CODE(s) 1, 2, 4 OR 5 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and AKFC and AKFD and AKFB and ABPX)
IF STYLE/REPLY CODE(s) 56A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABPX and AKFQ and ABTB and ADAT and AKFT)
IF STYLE/REPLY CODE(s) 56B WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFV and AKFR and ABTB and ABPX)
IF STYLE/REPLY CODE(s) 57A, 57B, 57C, 57D, 57E OR 57F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ABPX and AKFK and ADAT)
IF STYLE/REPLY CODE(s) 58A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFV and ADAT and ABTB and AKFR and ABPX)
IF STYLE/REPLY CODE(s) 58B WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ADAT and AKFT and AKFQ and ABPX)
IF STYLE/REPLY CODE(s) 3 OR 6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and AKFC and AKFB and AJDW and AKFD and ABPX)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAT and AKFK and ABPX)
IF STYLE/REPLY CODE(s) 54 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFQ and AKFS and ABPX and AKFH and AKFK and ABHP and ADFY and ABTB)
IF STYLE/REPLY CODE(s) 91 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAT and ABPX and ABTB and AKFS)
IF STYLE/REPLY CODE(s) 92, 93 OR 94 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFS and ADAT and ABHP and ABTB and AKFC)
IF STYLE/REPLY CODE(s) 8 OR 9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABTB and ADAT and AKFK and ABPX)
IF STYLE/REPLY CODE(s) 55 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AKFJ and ABHP and AKFK and AKFS and ABPX)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL70)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAL1461 | 1 | SINGLE SAFETY |
| AAL1470 | 10 | BUTT |
| AAL1471 | 11 | BUTT |
| AAL1472 | 12 | BUTT |
| AAL1473 | 13 | BUTT |
| AAL1474 | 14 | BUTT |
| AAL1475 | 15 | BUTT |
| AAL1476 | 16 | BUTT |
| AAL1477 | 17 | BUTT |
| AAL1478 | 18 | BUTT |
| AAL1479 | 19 | BUTT |
| AAL1462 | 2 | SINGLE NONSAFETY |
| AAL1480 | 20 | BUTT |
| AAL1481 | 21 | BUTT |
| AAL1482 | 22 | BUTT FRICTION ADJUSTABLE |
| AAL1483 | 23 | BUTT FRICTION ADJUSTABLE |
| AAL1484 | 24 | BUTT W/DOOR LEAF OFFSET |
| AAL1485 | 25 | BUTT W/JAMB LEAF OFFSET |
| AAL1486 | 26 | BUTT W/DOOR AND JAMB LEAF OFFSETS |
| AAL1487 | 27 | BUTT W/JAMB LEAF OFFSET |
| AAL1488 | 28 | BUTT W/DOOR AND JAMB LEAF OFFSET |
| AAL1489 | 29 | BUTT W/JAMB LEAF OFFSET |
| AAL1463 | 3 | DOUBLE SAFETY |
| AAL1490 | 30 | BUTT W/DOOR LEAF OFFSET |
| AAL1491 | 31 | BUTT, DOUBLE ACTION, ADJUSTABLE ENCLOSED SPRING |
| AAL1492 | 32 | BUTT, DOUBLE ACTION, NON-ADJUSTABLE ENCLOSED SPRING |
| AAL1493 | 33 | BUTT, SINGLE ACTION, ADJUSTABLE, ENCLOSED SPRING |
| AAL1494 | 34 | BUTT, SINGLE ACTION ADJUSTABLE, ENCLOSED SPRING |
| AAL1495 | 35 | BUTT, SINGLE ACTION, NON-ADJUSTABLE ENCLOSED SPRING |
| AAL1496 | 36 | BUTT, SINGLE ACTION, NON-ADJUSTABLE, EXPOSED SPRING |
| AAL1497 | 37 | BUTT, SINGLE ACTION, NON-ADJUSTABLE, EXPOSED SPRING |
| AAL1498 | 38 | BUTT, SINGLE ACTION, NON-ADJUSTABLE, EXPOSED SPRING |
| AAL1464 | 4 | SINGLE SAFETY |
| AAL1499 | 45 | BUTT BLANK |
| AAL1500 | 46 | BUTT PARALLEL HOLES |
| AAL1501 | 47 | BUTT STAGGERED HOLES |
| AAL1502 | 48 | BUTT BLANK |
| AAL1503 | 49 | BUTT PARALLEL HOLES |
| AAL1465 | 5 | SINGLE NONSAFETY |
| AAL1504 | 50 | BUTT STAGGERED HOLES |
| AAL1505 | 51 | BUTT BLANK |
| AAL1506 | 52 | BUTT PARALLEL HOLES |
| AAL1507 | 53 | BUTT STAGGERED HOLES |
| AAL1508 | 54 | BUTT PARRALLEL HOLES END KNUCKLES |
| AAL1509 | 55 | BUTT BLANK |
| AAL1527 | 56A | STRAP W/JAMB LEAF OFFSET |
| AAL1528 | 56B | STRAP W/DOOR LEAF OFFSET |
| AAL1529 | 57A | STRAP |
| AAL1530 | 57B | STRAP |
| AAL1531 | 57C | STRAP |
| AAL1532 | 57D | STRAP |
| AAL1533 | 57E | STRAP |
| AAL1534 | 57F | STRAP |
| AAL1535 | 58A | STRAP W/DOOR LEAF OFFSET |
| AAL1536 | 58B | STRAP W/JAMB LEAF OFFSET |
| AAL1466 | 6 | DOUBLE SAFETY |
| AAL1510 | 60 | STRAP |
| AAL1511 | 61 | STRAP |
| AAL1512 | 62 | STRAP |
| AAL1513 | 63 | STRAP W/DOOR LEAF OFFSET |
| AAL1514 | 64 | STRAP W/JAMB LEAF OFFSET |
| AAL1515 | 68 | TEE |
| AAL1516 | 69 | TEE |
| AAL1467 | 7 | BUTT |
| AAL1517 | 70 | TEE W/DOOR LEAF OFFSET |
| AAL1518 | 71 | TEE |
| AAL1519 | 72 | TEE |
| AAL1520 | 73 | TEE |
| AAL1521 | 74 | TEE |
| AAL1522 | 75 | TEE |
| AAL1468 | 8 | BUTT |
| AAL1469 | 9 | BUTT |
| AAL1523 | 91 | HOOK/PLATE |
| AAL1524 | 92 | PLATE |
| AAL1525 | 93 | PLATE |
| AAL1526 | 94 | BLOCK |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABPX*JMATERIAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPX3AEEJAB2.0*;ABPX3AEEJAB2.0$JAB2.0*;ABPX3AEEJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAC2.0*;ABTBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVV*JPIN DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A PIN,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVVJAB2.0*;ABVVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAT3AEEJAB2.0*;ADAT3AEEJAB2.0$JAB2.0*;ADAT3AEEJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADFY*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING HOLES ALONG LENGTH
A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE MOUNTING HOLES ALONG THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADFYJAB2.0*;ADFYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJDW*JCENTER TO CENTER DISTANCE BETWEEN PINS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJDWJAC2.0*;AJDWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFB*JSLOTTED LEAF LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFBJAC2.0*;AKFBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFC*JLEAF WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFCJAA2.0*;AKFCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFD*JFIXED LEAF LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFDJAA2.0*;AKFDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFF*JLEAF OUTER EDGE TO HOLE CENTER VERTICAL DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFFJAB2.0*;AKFFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFH*JKNUCKLE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFHJAB2.0*;AKFHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFJ*JEND KNUCKLE LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFJJAC2.0*;AKFJJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFK*JPIN CENTER TO BODY EDGE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFKJAB2.0*;AKFKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFL*JJAMB LEAF WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFLJAC2.0*;AKFLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFM*JDOOR LEAF WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFMJAA2.0*;AKFMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFN*JPIN CENTER TO JAMB LEAF EDGE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFNJAA2.0*;AKFNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFP*JPIN CENTER TO DOOR LEAF EDGE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFPJAB2.0*;AKFPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFQ*JJAMB LEAF OFFSET DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFQJAC2.0*;AKFQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFR*JDOOR LEAF OFFSET DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFRJAC2.0*;AKFRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFS*JKNUCKLE INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFSJAC2.0*;AKFSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFT*JDEVELOPED DISTANCE FROM PIN CENTER TO OFFSET JAMB LEAF EDGE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFTJAB2.0*;AKFTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKFV*JDEVELOPED DISTANCE FROM PIN CENTER TO OFFSET DOOR LEAF EDGE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKFVJAC2.0*;AKFVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKEV*LPIN TIP STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PIN TIP.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AKEVL6*;AKEVL3$L4*;AKEVL3$$L4*)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAL1537 | 1 | CONE |
| AAL1538 | 2 | STEEPLE |
| AAL1539 | 3 | BALL |
| AAL1540 | 4 | OVAL HEAD |
| AAL1541 | 5 | HOSPITAL TYPE |
| AAL1542 | 6 | FLAT BUTTON |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3ADTDCDA000*;SFTT3ADTDCDA000$DCRA000*;SFTT3ADTDCDA000$$DCRA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ADT | SPRING |
| 3AEE | OVERALL |
| 3AZT | PIN |
| 3DPT | BALL BEARING |
| 3DQR | LEAF |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3ICH | BUTTON TIP |
| Table 2 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| ENA000 | ENAMEL |
| ENE000 | ENAMEL GLOSS |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| NLB000 | NICKEL SILVER |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| AAA000 | PAINTED |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PHD000 | PHOSPHATE ZINC |
| PCA000 | PLASTIC |
| PCS000 | PLASTIC EPOXY |
| PCF000 | PLASTIC POLYAMIDE |
| AAA014 | POLISHED |
| PRA000 | PRIMER |
| LBG000 | SOLID FILM LUBRICANT |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACK | BUSHING |
| 3ADT | SPRING |
| 3AEE | OVERALL |
| 3AZT | PIN |
| 3DPT | BALL BEARING |
| 3DQR | LEAF |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3ICH | BUTTON TIP |
| Table 2 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
AKER*DHINGE MOUNTING TYPE
INDICATES THE TYPE OF HINGE WHICH PERMITS EITHER MORTISE OR SURFACE MOUNTING.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AKER3AEEDAE*;AKER3AEEDAE$DAD*;AKER3AEEDAE$$DAD*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AG29) | Reply |
| AB | FULL MORTISE |
| AC | FULL SURFACE |
| AD | HALF MORTISE |
| AE | HALF SURFACE |
AKNB*DKNUCKLE TYPE
INDICATES THE TYPE OF CYLINDRICAL PROJECTION THROUGH WHICH AN AXIS OR PIN PASSES.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AKNB3AEEDAE*;AKNB3AEEDAE$DAC*;AKNB3AEEDAE$$DAC*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AG30) | Reply |
| AB | BALL BEARING |
| AD | BUSHING |
| AC | FRICTION |
| AE | WAFER |
ABTJ*AMOUNTING HOLE QUANTITY
THE NUMBER OF MOUNTING HOLES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ABTJA10*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDGJ)
| Table 1 |
| Reply Code (AB28) | Reply |
| GG | BOLT |
| GJ | SCREW |
ADJH*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM. PLEASE USE MRC AXGY IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ADJHDBU)
| Table 1 |
| Reply Code (AB89) | Reply |
| BU | UNTHREADED HOLES |
| AW | WELDED |
AWJN*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWJNJAS2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BA | GRAMS |
| AJ | KILOGRAMS |
| AS | POUNDS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDIRA000*;PRMTDPDA000$DAUA000*;PRMTDPDA000$$DAUA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000F2.0*;PMWTJPDA000F2.0$JPDA000F2.0*;PMWTJPDA000F2.0$$JPDA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$JPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
PKQT*AINTERMEDIATE PACKAGE QUANTITY
THE NUMBER OF WRAPS,BOXES,OR BUNDLES,WHICH CONTAINS TWO OR MORE UNITS OF ISSUE,PLACED INSIDE AN EXTERIOR CONTAINER.
Enter the numeric reply with a minimum of one digit.
(PKQTA10*)
EXQT*AEXTERIOR CONTAINER QUANTITY
THE NUMBER OF UNITS OF ISSUE PLACED INSIDE THE EXTERIOR CONTAINER. PLEASE USE MRC NMBR WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the numeric reply with a minimum of one digit.
(EXQTA10*)
SUWT*JUNIT OF ISSUE WEIGHT
THE MEASURED WEIGHT OF THE ACTUAL CONTAINER(S) OR SUPPORTING DEVICE(S) WHICH IS IN DIRECT CONTACT WITH THE ITEM AND ITS CONTENTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUWTJKG2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
ECWT*JEXTERIOR CONTAINER WEIGHT
THE MEASURED WEIGHT OF THE EXTERIOR CONTAINER. PLEASE USE MRC AJWK WITH ISAC CODING OF OUTER CONTAINER IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ECWTJKG2.0*)
| Table 1 |
| Reply Code (AN75) | Reply |
| KG | KILOGRAMS |
| LB | POUNDS |
SUCB*JUNIT OF ISSUE CUBE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE UNIT OF ISSUE AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(SUCBJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
EXME*JEXTERIOR CONTAINER CUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF THE EXTERIOR CONTAINER AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(EXMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCC2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information