A cylindrical item with or without flange(s), designed to be inserted in a pump casing or secured to the impeller of a centrifugal pump. It is used for the purpose of providing a close running clearance between the impeller and casing in order to prevent or overcome leakage due to erosion. It may also be used as a diffuser ring in the suction and discharge throats of valves.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED22534*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDST3140*;MATTDPCA000$DCU0172*;MATTDPCA000$$DCU0172*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0038 | ALUMINUM ALLOY 222.0 |
| AL0039 | ALUMINUM ALLOY 242.0 |
| AL0333 | ALUMINUM ALLOY 333.0 |
| AL0045 | ALUMINUM ALLOY 355.0 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL0044 | ALUMINUM ALLOY 443.0 |
| AL0047 | ALUMINUM ALLOY 705.0 |
| AL0048 | ALUMINUM ALLOY 707.0 |
| AL0049 | ALUMINUM ALLOY 713.0 |
| AL0063 | ALUMINUM ALLOY A332.0 |
| AL0040 | ALUMINUM ALLOY B295.0 |
| ALC000 | ALUMINUM-COPPER FREE |
| CNB000 | CARBON GRAPHITE |
| CLD000 | CERAMIC |
| CRB000 | CHROMIUM ALLOY |
| CUB000 | COPPER ALLOY |
| CU0099 | COPPER ALLOY 464 |
| CU0103 | COPPER ALLOY 510 |
| CU0172 | COPPER ALLOY 836 |
| CU0195 | COPPER ALLOY 903 |
| CU0196 | COPPER ALLOY 905 |
| CU0198 | COPPER ALLOY 910 |
| CU0202 | COPPER ALLOY 922 |
| CU0203 | COPPER ALLOY 923 |
| CU0206 | COPPER ALLOY 932 |
| CU0207 | COPPER ALLOY 934 |
| CU0209 | COPPER ALLOY 937 |
| CU0210 | COPPER ALLOY 938 |
| CU0214 | COPPER ALLOY 943 |
| CU0944 | COPPER ALLOY 944 |
| CU0945 | COPPER ALLOY 945 |
| CU0217 | COPPER ALLOY 952 |
| CU0220 | COPPER ALLOY 955 |
| CU0224 | COPPER ALLOY 964 |
| FBA000 | FIBER |
| GSA000 | GLASS |
| GFA000 | GRAPHITE |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| FEB000 | IRON CAST |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| NL0001 | NICKEL ALLOY A |
| NL0002 | NICKEL ALLOY B |
| NL0011 | NICKEL ALLOY D |
| NL0013 | NICKEL ALLOY E |
| NL0018 | NICKEL ALLOY K-500 |
| PCA000 | PLASTIC |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RC0012 | RUBBER POLYMETHYLENE-PERFLUOROALKYLENE CLASS FKM |
| RCB000 | RUBBER SYNTHETIC |
| SLB000 | SILICON CARBIDE |
| STA000 | STEEL |
| ST1015 | STEEL COMP 1015 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1020 | STEEL COMP 1020 |
| ST1030 | STEEL COMP 1030 |
| ST1095 | STEEL COMP 1095 |
| ST1117 | STEEL COMP 1117 |
| ST0303 | STEEL COMP 303 |
| ST0304 | STEEL COMP 304 |
| ST3140 | STEEL COMP 3140 |
| ST0316 | STEEL COMP 316 |
| ST0410 | STEEL COMP 410 |
| ST0416 | STEEL COMP 416 |
| ST0420 | STEEL COMP 420 |
| ST0107 | STEEL COMP 440C |
| ST0938 | STEEL COMP Z2CND17-12 |
| STB000 | STEEL CORROSION RESISTING |
| AAA012 | THERMOPLASTIC |
| TTB000 | TITANIUM |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRG and AYRE and ABKG and AECS and AEBV)
IF STYLE/REPLY CODE(s) 2A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRG and AYRE and ABKG and AECS and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKG and AECS and AEBV)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKG and AECS and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRE and AYRG)
IF STYLE/REPLY CODE(s) 5 OR 44 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGA and ABGF and AXHQ and ANTT)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AJFM and AYRG and ABGA and ABGF and ADXL and ADXM and AGRS and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL and ABKG and AECS and AEBV)
IF STYLE/REPLY CODE(s) 7A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL and ABKG and AECS and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and AYRJ and AJFM and AYRR and AYRN)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRE and AYRG and AYRJ and AJFM and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL and AYRG and AYRE and AECS and ABKG and AEBV)
IF STYLE/REPLY CODE(s) 10A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL and AYRG and AYRE and AECS and ABKG and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRT and AYRJ and AJFM and AYRM and AYRL and AYRK)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and AYRH and AYRF and AYRG and AYRJ and AJFM and AYRE and AYRQ and AYRP)
IF STYLE/REPLY CODE(s) 13 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AJFM and AYRM and AYRL and AYRK)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL and AYRW and AECS)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGA and ABGF and ANTT and AJFM and AYRJ and AYRE and AYRG and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 16 OR 21 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRF and AJFM and AYRG and AYRH and AYRE)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL)
IF STYLE/REPLY CODE(s) 18 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AJFM and ADNA and ABKK and AECS and ABKG and AEBV)
IF STYLE/REPLY CODE(s) 18A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AJFM and ADNA and ABKK and AECS and ABKG and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AYRS and ADNA and AJFM and ASBM and ABKK and ABKG and AECS and AEBV)
IF STYLE/REPLY CODE(s) 19A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AYRS and ADNA and AJFM and ASBM and ABKK and ABKG and AECS and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 22 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AJFM and AYRG and AYRE and ADXL and ABKK and AAWY and AAWZ and AECS and ABKG and AEBV)
IF STYLE/REPLY CODE(s) 22A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AJFM and AYRG and AYRE and ADXL and ABKK and AAWY and AAWZ and AECS and ABKG and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 23 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AJFM and AYRJ and AYRE and AYRG and AYRM and AYRX and ANTT and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 24 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGA and ABGF and AYRX and ANTT and AYRJ and AJFM and AYRE and AYRG and AYRM and AYRL and AYRK)
IF STYLE/REPLY CODE(s) 26 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AJFM and AYRJ and AYRG and ABKK and AYRE and AYRN and AYRR)
IF STYLE/REPLY CODE(s) 27 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRS and ABGA and AYRM and ABGF and ANTT and ANTZ)
IF STYLE/REPLY CODE(s) 28 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ADXM and AYRS and AYRG and AYRE and AYRM and AYRL and AYRK)
IF STYLE/REPLY CODE(s) 29 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGA and ABGF and ADXL and ADXM and AGRS and AYRS and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRR and AXHQ and ABGA and ADXL and AJFM and ABKK and ABKG and AECS and AAZQ and AEBV)
IF STYLE/REPLY CODE(s) 30A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRR and AXHQ and ABGA and ADXL and AJFM and ABKK and ABKG and AECS and AAZQ and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 31 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ADXL and AJFM and ABKK and AYRE and AYRG and AAWY and AAWZ and ABKG and AECS and AAZQ and AEBV)
IF STYLE/REPLY CODE(s) 31A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ADXL and AJFM and ABKK and AYRE and AYRG and AAWY and AAWZ and ABKG and AECS and AAZQ and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 32 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRE and AYRJ and AJFM and AYRG and ABKK and AAUB and AAZQ)
IF STYLE/REPLY CODE(s) 33 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AAWY and AAWZ and AXHQ and ABGA and ABGF and AECS and AYRZ and CRSQ and AAUB)
IF STYLE/REPLY CODE(s) 34 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ADXL and ADXM and AGRS and AYRE and AYRG and AYRM and AJFM and AYRS and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 35 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ADXL and ADXM and AGRS and AJFM and AYRS and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 36 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRF and ADXL and ADXM and AGRS and AJFM and AYRS and AYRG and AYRE and AYRH and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 37 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ADXL and ADXM and AGRS and AYRH and AYRG and AYRE and AYRF and AYRS and AYRM and AYRK and AYRL)
IF STYLE/REPLY CODE(s) 38 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRW and ANTT and ABGA and ABGF and AECS and AAUB)
IF STYLE/REPLY CODE(s) 39 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAS and AYRG and AYRE and AYRW and AYRJ and AJFM and ABKK and AECS and AAUB)
IF STYLE/REPLY CODE(s) 40 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ABGA and ABGF and ADXL and ADXM)
IF STYLE/REPLY CODE(s) 41 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGA and ASBM and AYRS and ABGF and ANTT and AECS and AAUB and AAZQ)
IF STYLE/REPLY CODE(s) 42 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABKK and ADXL and ADXM and AGRS and AJFM and AYRM and AYRL and AYRK)
IF STYLE/REPLY CODE(s) 43 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRJ and AJFM and ABGF and ABGA and AYRK and AYRL and AYRM)
IF STYLE/REPLY CODE(s) 46 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGF and ANTT and ABGA and AYRW and AYRM and AECS and AEBV)
IF STYLE/REPLY CODE(s) 46A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and ABGF and ANTT and ABGA and AYRW and AYRM and AECS and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 48 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and AECS and AAZQ and ABKG and AYRF and ABGA and ABGF and ANTT and AYRE and AEBV)
IF STYLE/REPLY CODE(s) 48A WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and AECS and AAZQ and ABKG and AYRF and ABGA and ABGF and ANTT and AYRE and CMLK and CQLT)
IF STYLE/REPLY CODE(s) 49 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ADAR and ADAS and AYRE and ABGA and ABGF and ANTT and AECS and AAUB and AAZQ and ABKG)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL46A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAN1273 | 1 | PLAIN |
| DR03641 | 10 | INTERNAL AND EXTERNAL FLANGE |
| DR03642 | 10A | INTERNAL AND EXTERNAL FLANGE |
| AAN1282 | 11 | EXTERNAL LOCKING FLANGE |
| AAN1283 | 12 | INTERNAL AND EXTERNAL FLANGE |
| AAN1284 | 13 | EXTERNAL LOCKING FLANGE |
| AAN1285 | 14 | EXTERNAL FLANGE |
| AAN1286 | 15 | GROOVED W/INTERNAL AND EXTERNAL FLANGE |
| AAN1287 | 16 | PLAIN W/INTERNAL FLANGE |
| AAN1288 | 17 | EXTERNAL FLANGE |
| DR02829 | 18 | EXTERNAL FLANGE |
| DR02830 | 18A | EXTERNAL FLANGE |
| DR02831 | 19 | EXTERNAL FLANGE |
| DR02832 | 19A | EXTERNAL FLANGE |
| DR02823 | 2 | PLAIN W/INTERNAL FLANGE |
| AAN1291 | 21 | INTERNAL FLANGE |
| DR02833 | 22 | EXTERNAL FLANGE |
| DR02834 | 22A | EXTERNAL FLANGE |
| AAN1293 | 23 | INTERNAL FLANGE W/EXTERNAL LOCKING FLANGE |
| AAN1294 | 24 | GROOVED W/EXTERNAL LOCKING FLANGE |
| AAN1295 | 26 | EXTERNAL AND INTERNAL FLANGE |
| AAN1296 | 27 | GROOVED W/EXTERNAL LOCKING FLANGE |
| AAN1297 | 28 | EXTERNAL LOCKING FLANGE |
| AAN1298 | 29 | EXTERNAL LOCKING FLANGE |
| DR02824 | 2A | PLAIN W/INTERNAL FLANGE |
| DR02825 | 3 | PLAIN |
| DR02835 | 30 | EXTERNAL FLANGE |
| DR02836 | 30A | EXTERNAL FLANGE |
| DR02837 | 31 | EXTERNAL AND INTERNAL FLANGE |
| DR02838 | 31A | EXTERNAL AND INTERNAL FLANGE |
| AAN1301 | 32 | EXTERNAL AND INTERNAL FLANGE |
| AAN1302 | 33 | GROOVED |
| AAN1303 | 34 | INTERNAL FLANGE W/EXTERNAL LOCKING FLANGE |
| AAN1304 | 35 | EXTERNAL LOCKING FLANGE |
| AAN1305 | 36 | INTERNAL FLANGE W/EXTERNAL LOCKING FLANGE |
| AAN1306 | 37 | INTERNAL FLANGE W/EXTERNAL LOCKING FLANGE |
| AAN1307 | 38 | GROOVED |
| AAN1308 | 39 | INTERNAL AND EXTERNAL FLANGE |
| DR02826 | 3A | PLAIN |
| AAN1276 | 4 | PLAIN W/INTERNAL FLANGE |
| AAN1309 | 40 | EXTERNAL AND INTERNAL GROOVED |
| AAN1310 | 41 | EXTERNAL GROOVE |
| AAN1311 | 42 | EXTERNAL LOCKING FLANGE |
| AAN1312 | 43 | EXTERNAL LOCKING FLANGE |
| AAN1313 | 44 | PLAIN |
| DR02839 | 46 | EXTERNAL GROOVE |
| DR02840 | 46A | EXTERNAL GROOVE |
| DR02841 | 48 | IMPELLER W/EXTERNAL GROOVE |
| DR02842 | 48A | IMPELLER W/EXTERNAL GROOVE |
| AAN1316 | 49 | IMPELLER W/EXTERNAL GROOVE |
| AAN1277 | 5 | GROOVED |
| AAN1278 | 6 | EXTERNAL LOCKING FLANGE |
| DR02827 | 7 | EXTERNAL FLANGE |
| DR02828 | 7A | EXTERNAL FLANGE |
| AAN1280 | 8 | EXTERNAL FLANGE |
| AAN1281 | 9 | EXTERNAL LOCKING FLANGE |
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJAA2.0*;AAUBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWY*JCOUNTERBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWYJAA2.0*;AAWYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWZ*JCOUNTERBORE DEPTH
THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWZJAA2.0*;AAWZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZQ*JHOLE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZQJAB2.0*;AAZQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGA*JGROOVE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGAJAA2.0*;ABGAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGF*JGROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGFJAC2.0*;ABGFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAB2.0*;ABKGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKK*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKKJAB2.0*;ABKKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAR*JBODY OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADARJAA2.0*;ADARJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAS*JBODY INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADASJAC2.0*;ADASJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNA*JMINOR OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNAJAC2.0*;ADNAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADXL*JLEFT SIDE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADXLJAA2.0*;ADXLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADXM*JRIGHT SIDE FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADXMJAB2.0*;ADXMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGRS*JDISTANCE BETWEEN FLANGES
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGRSJAA2.0*;AGRSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJFM*JEND TO FLANGE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJFMJAB2.0*;AJFMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANTT*JDISTANCE FROM END TO GROOVE CENTER
THE DISTANCE FROM THE CENTER OF THE GROOVE TO THE END OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANTTJAC2.0*;ANTTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANTZ*JDISTANCE BETWEEN GROOVE CENTERS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANTZJAC2.0*;ANTZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASBM*JHUB DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HUB,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASBMJAB2.0*;ASBMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRE*JINTERNAL FLANGE INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYREJAC2.0*;AYREJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRF*JINTERNAL FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRFJAB2.0*;AYRFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRG*JINTERNAL FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRGJAB2.0*;AYRGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRH*JINTERNAL FLANGE LIP WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRHJAC2.0*;AYRHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRJ*JCENTER FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRJJAB2.0*;AYRJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRK*JSMALLEST EXTERNAL ANCHOR FLANGE RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRKJAC2.0*;AYRKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRL*JLARGEST EXTERNAL ANCHOR FLANGE RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRLJAB2.0*;AYRLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRM*JDISTANCE BELOW CENTERLINE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRMJAC2.0*;AYRMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRN*JPOSITIONING HOLE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRNJAC2.0*;AYRNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRP*JPOSITIONING LUG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRPJAB2.0*;AYRPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRQ*JPOSITIONING LUG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRQJAB2.0*;AYRQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRR*JPOSITIONING HOLE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRRJAC2.0*;AYRRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRS*JDISTANCE FROM END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRSJAA2.0*;AYRSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRT*JANCHOR FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRTJAA2.0*;AYRTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRW*JDISTANCE FROM HOLE CENTER TO RIGHT FACE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRWJAA2.0*;AYRWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRX*JANCHOR GROOVE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRXJAC2.0*;AYRXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AYRZ*JCOUNTERSINK DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COUNTERSINK,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYRZJAC2.0*;AYRZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AECS*ABOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AECSA10*)
AXHQ*AGROOVE QUANTITY
THE NUMBER OF GROOVES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AXHQA10*)
CRSQ*JCOUNTERSINK ANGLE
THE INCLUDED ANGLE OF THE COUNTERSINK.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRSQJDC2.0*;CRSQJDC2.0$$JDC2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAA2.0*;AEBVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CMLK*DMOUNTING HOLE THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR THE SPECIFIC DIAMETER OF A THREADED MOUNTING HOLE.
Enter the applicable reply code from the table below
(CMLKDNF)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| NC | UNC |
| NF | UNF |
CQLT*JMOUNTING HOLE NOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE MOUNTING HOLE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQLTJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) AB WERE ENTERED FOR MRC BZLX, YOU MUST ANSWER MRC (CSYT and AAZP)
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC BZLX, YOU MUST ANSWER MRC (ADNU)
BZLXDCORNER SHAPE
THE PHYSICAL CONFIGURATION OF THE CORNER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(BZLX3CGCDAC*;BZLX3CGCDAC$DAF*;BZLX3CGCDAC$$DAF*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CGB | INSIDE LEFT CORNER |
| 3CGC | INSIDE RIGHT CORNER |
| 3CGD | OUTSIDE LEFT CORNER |
| 3CGE | OUTSIDE RIGHT CORNER |
| 3CGF | ALL CORNERS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AE88) | Reply |
| AB | CHAMFERED |
| AC | ROUND |
| AF | SQUARE |
CSYT*JCHAMFER ANGLE
THE INCLUDED ANGLE OF THE CHAMFER(S).
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYT3CGFJDB2.0*;CSYT3CGFJDB2.0$JDB2.0*;CSYT3CGFJDB2.0$$JDB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CGB | INSIDE LEFT CORNER |
| 3CGC | INSIDE RIGHT CORNER |
| 3CGD | OUTSIDE LEFT CORNER |
| 3CGE | OUTSIDE RIGHT CORNER |
| 3CGF | ALL CORNERS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
AAZP*JCHAMFER LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE CHAMFER,IN DISTINCTION FROM WIDTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZP3AEEJAC2.0*;AAZP3AEEJAC2.0$JAC2.0*;AAZP3AEEJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CGB | INSIDE LEFT CORNER |
| 3CGC | INSIDE RIGHT CORNER |
| 3CGD | OUTSIDE LEFT CORNER |
| 3CGE | OUTSIDE RIGHT CORNER |
| 3CGF | ALL CORNERS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADNU*JCORNER RADIUS
A MEASUREMENT OF A STRAIGHT LINE FROM THE MIDPOINT OF A ROUNDED CORNER TO ITS PERIPHERY.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNU3CGDJAA2.0*;ADNU3CGDJAA2.0$JAA2.0*;ADNU3CGDJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CGB | INSIDE LEFT CORNER |
| 3CGC | INSIDE RIGHT CORNER |
| 3CGD | OUTSIDE LEFT CORNER |
| 3CGE | OUTSIDE RIGHT CORNER |
| 3CGF | ALL CORNERS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CSYM*JSURFACE FINISH
DESIGNATES THE SPECIFIC SURFACE ROUGHNESS RATING,REPRESENTING THE ARITHMETIC AVERAGE DEVIATION OF THE SURFACE FROM THE MEANLINE IN PROFILE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSYM3AUWJB2.0*;CSYM3AUWJB2.0$JB2.0*;CSYM3AUWJB2.0$$JB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALQ | ALL SURFACES |
| 3AUC | INSIDE |
| 3AUW | OUTSIDE |
| 3BEB | COUNTERBORE |
| 3CGG | LEFT FACE |
| 3CGH | RIGHT FACE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AE86) | Reply |
| B | MICROINCHES |
| C | MICRONS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAB*;BBRGDAX$DAS*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AB | ABOVE GROUND MAGAZINE |
| AT | DOCK LEVEL HEATED WAREHOUSE |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AS | GROUND LEVEL HEATED WAREHOUSE |
| AW | GROUND LEVEL UNHEATED WAREHOUSE |
| AF | IGLOO MAGAZINE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AK | UNIMPROVED OPEN |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)