An item, solid or split, designed to be used as a hollow form into which potting compound is injected and allowed to cure or set to seal the back of an electrical connector. The potting eliminates the need for a back shell of the connector. The form may or may not be removable after potting. See also SHIELD, ELECTRICAL CONNECTOR.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED22036*)
AXHRJMOUNTING FACILITY TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES BY WHICH THE ITEM IS MOUNTED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(AXHRJAET2*;AXHRJAET2$$JAET3*;AXHRJAET2$JAET2*)
| Table 1 |
| Reply Code (AM39) | Reply |
| AFE | BAYONET LOCK |
| AQS | BODY |
| AAC | BOLT |
| ABC | BRACKET |
| BRK | CLAMP ASSEMBLY |
| AEC | CLINCH NUT |
| AFL | CLIP |
| ACR | FLANGE |
| BRL | FORCE SPRING |
| BRM | JACKSCREW |
| BGA | NUT |
| AED | PANEL |
| ABP | PLUG-IN |
| ADC | PRESS FIT |
| ABW | SCREW |
| ABY | SLOT |
| ADF | SNAP-IN |
| AJK | SPRING TENSION |
| BRN | SPRINGLOCK FASTENER |
| AAE | STUD |
| ACC | TAB |
| AFA | THREADED BUSHING |
| APZ | THREADED COUPLING |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| AHD | TWIST LOCK |
| ACQ | UNTHREADED HOLE |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDPCA000*;MATTDPCAW00$DPCP000*;MATTDPCAW00$$DPCP000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| CUB000 | COPPER ALLOY |
| PCA000 | PLASTIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCAB00 | PLASTIC POLYOLEFIN |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| RCE000 | RUBBER |
| RCB000 | RUBBER SYNTHETIC |
| STA000 | STEEL |
| STB000 | STEEL CORROSION RESISTING |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) 1F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABMK and ABKW)
IF STYLE/REPLY CODE(s) 2F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and ABHP)
IF STYLE/REPLY CODE(s) 3F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABHP and ABMK)
IF STYLE/REPLY CODE(s) 4F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABMK and AEJN and ABHP and ABKW)
IF STYLE/REPLY CODE(s) 5F OR 6F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ADAU and ABMK and ABHP)
IF STYLE/REPLY CODE(s) 7F WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAU and ADAV and AEBV and ABHP)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL6F)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BD10091 | 1F | RECTANGULAR SHAPE TAPERED BACK |
| BD10092 | 2F | ROUND SHAPE TAPERED BACK |
| BD10093 | 3F | ANGULAR SHAPE |
| BD10094 | 4F | RECTANGULAR SHAPE W/FLANGE |
| BD10095 | 5F | RECTANGULAR SHAPE |
| BD10096 | 6F | RECTANGULAR SHAPE |
| DR11428 | 7F | WITHOUT INTERNAL & EXTERNAL BAYONET THREADS WITH ROPE / CHAIN |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAC2.0*;ABKWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAB2.0*;ABMKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAA2.0*;ADAUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJNJAA2.0*;AEJNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAA2.0*;AEBVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTJS*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMERED BY PACKAGING OR PACKING MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTJSJKGC2.0*;CTJSJKGC2.0$JKGC2.0*;CTJSJKGC2.0$$JKGC2.1*)
| Table 1 |
| Reply Code (AN75) | Reply |
| GM | GRAMS |
| KG | KILOGRAMS |
| OZ | OUNCES |
| LB | POUNDS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDCRA000*;SFTTDAGA000$DCMA000*;SFTTDAGA000$$DCMA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CRA000 | CHROMIUM |
| ENA000 | ENAMEL |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PCP000 | PLASTIC POLYSULFONE |
| AGA000 | SILVER |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVGJAC2.0*;ABVGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAB2.0*;ABTDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AM, AZ, DS, JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD and AAJF)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CQQR and AAJF) or (CQJX and CTTC and AAJF) or (CQJX and AAJE and AAJF)
IF STYLE/REPLY CODE(s) NP WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJF)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD and AAJF)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD and AAJF) or (CQJX and CMLP and AAJE and AAJF)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDNP*;THSDDDS$$DNC*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| DS | DOUBLE STUB |
| SM | ISO M |
| SS | ISO S |
| NP | NPT |
| AZ | SPECIAL ACME |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*;CQJXJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAU4)
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJNTE2.0*;CTTCJNTE2.0$$JNTE2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAX4)
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0*;CQQRB2.0$$BM2.0*)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*;AAJEJAM32.0/P50.0$$JA*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG*;AAJFDAAL$$DAAG*)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AKMG*JNOMINAL THREAD LENGTH
A NOMINAL MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKMGJA2.0*;AKMGJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AKRD*ACABLE OPENING QUANTITY
THE NUMBER OF OPENINGS DESIGNED TO ACCOMMODATE A CABLE.
Enter the numeric reply with a minimum of one digit.
(AKRDA10*)
AGTW*JCABLE OPENING DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE OPENING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGTWJAB2.0*;AGTWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGTX*JCABLE OPENING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE OPENING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGTXJAA2.0*;AGTXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGTY*JCABLE OPENING WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CABLE OPENING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGTYJAB2.0*;AGTYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDARC*;ABFFDAQH$DAQC*;ABFFDAQH$$DAQC*)
| Table 1 |
| Reply Code (AB28) | Reply |
| ARP | 90 DEG STRAIN-RELIEF BOOT |
| APQ | BEAD CHAIN |
| ARC | BONDING RING |
| AEL | CAP |
| ARE | CAP W/WIRE ROPE |
| AMM | CHAIN |
| AMN | CLAMP |
| ARG | COVER W/CHAIN |
| ARH | COVER W/WIRE ROPE |
| AQC | DUST CAP |
| ARD | DUST CAP W/CHAIN |
| ARF | ELECTRICAL CONNECTOR COVER |
| AES | GLAND NUT |
| AKY | GLAND WASHER |
| ADM | GROMMET |
| AQD | GUIDE PIN |
| AQE | GUIDE SOCKET |
| AMF | JACKSCREW |
| AQH | JACKSCREW KNOB |
| AQJ | LANYARD |
| AQL | LINK CHAIN |
| ARJ | LOCK RING |
| ARK | LOCK SOCKET |
| ARL | POTTING HOLE PLUG |
| APW | PROTECTIVE CAP |
| AFF | RETAINING RING |
| ARM | RFI ADAPTER WASHER |
| AEF | RFI RING |
| ARN | RFI WEDGE |
| AFL | SOCKET |
| ARQ | STRAP |
| AJW | WASHER |
| ANA | WIRE ROPE |
ADTN*JATTACHMENT FEATURE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ATTACHMENT FEATURE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADTNJAC2.0*;ADTNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATK*JEYE INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE EYE AND TERMINATES AT THE INNER PERIPHERY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATKJAC2.0*;AATKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALJP*DSIZE DESIGNATION
A DESIGNATION INDICATING THE SIZE BY WHICH THE ITEM IS COMMERCIALLY KNOWN AND/OR IDENTIFIED.
Enter the applicable reply code from the table below
(ALJPDAJP*;ALJPDAAM$$DAPW*)
| Table 1 |
| Reply Code (AF81) | Reply |
| BGW | 0 |
| ABQ | 10 |
| ENC | 104 |
| END | 106 |
| EMR | 10S |
| EMS | 10SL |
| ABZ | 11 |
| ACG | 12 |
| ENE | 123 |
| EMT | 12S |
| ACX | 13 |
| ENF | 132 |
| ADF | 14 |
| EMW | 14S |
| ADV | 15 |
| ENG | 152 |
| ENH | 158 |
| AEB | 16 |
| ENJ | 160 |
| ENK | 163 |
| ENL | 164 |
| EMX | 16S |
| AEQ | 17 |
| AEX | 18 |
| ENM | 184 |
| AFL | 19 |
| AAC | 2 |
| AWS | 20 |
| AWT | 21 |
| ENN | 212 |
| AFZ | 22 |
| AWW | 23 |
| AGL | 24 |
| ENP | 244 |
| AWY | 25 |
| CST | 26 |
| ELR | 27 |
| AGY | 28 |
| AHD | 29 |
| AAD | 3 |
| AHV | 32 |
| AJC | 33 |
| AJP | 34 |
| AKN | 36 |
| ALA | 37 |
| ALQ | 38 |
| AAE | 4 |
| AMR | 40 |
| ANF | 41 |
| ENQ | 414 |
| ANV | 42 |
| APW | 44 |
| AQV | 48 |
| AAF | 5 |
| ARJ | 50 |
| ARX | 52 |
| AAM | 6 |
| CYY | 60 |
| EMY | 61 |
| EMZ | 66 |
| ENA | 67 |
| EMP | 6S |
| AAT | 7 |
| CYZ | 70 |
| ENB | 75 |
| AAZ | 8 |
| CZA | 80 |
| EMQ | 8S |
| ABJ | 9 |
| BDX | A |
| BDZ | B |
| EMJ | BNC |
| CYF | C |
| CYG | D |
| EMK | HN |
| EML | N |
| EMM | TM |
| EMN | TNC |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDDBN)
| Table 1 |
| Reply Code (AN47) | Reply |
| DBN | ELECTROMAGNETIC INTERFERENCE SHIELDING |
| AGQ | RFI SHIELDING |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRTA000R2.0*;PMWTJRTA000R2.0$JRTA000R2.0*;PMWTJRTA000R2.0$$JRTA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDB)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAD*;BBRGDAJ$$DAM*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AL | TEMPERATURE CONTROLLED WAREHOUSE |
| AJ | UNHEATED WAREHOUSE |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDAAD*;ADZCDABK$$DABW*)
| Table 1 |
| Reply Code (AA65) | Reply |
| ABY | ACID RESISTANT |
| AAD | DRIPPROOF |
| AAE | DUSTPROOF |
| AAG | EXPLOSION PROOF |
| AAX | OIL RESISTANT |
| AAZ | PRESSURE PROOF |
| ABW | SUBMERSIBLE |
| ABK | WATERPROOF |
| ABM | WEATHERPROOF |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information