A straight metal item having a solid or tubular circular cross section with serrations, flats, or the like, on each end. It is designed to withstand a severe twisting action along its longitudinal axis, while held fast at the ends. It is used in the suspension system of a vehicle to absorb road shock. See also TORQUE ROD, TANDEM AXLE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED21827*)
ASRXDTWIST DIRECTION
AN INDICATION OF THE TWIST DIRECTION.
Enter the applicable reply code from the table below
(ASRXDAAD)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAC | CLOCKWISE |
| AAD | COUNTERCLOCKWISE |
ADGNJFIRST END CHAMFER LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A CHAMFER AT THE FIRST END. REPLACED BY MRC AAZP WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADGNJAB2.0*;ADGNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADGRJSECOND END CHAMFER LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A CHAMFER AT THE SECOND END. REPLACED BY MRC AAZP WITH ISAC 0368.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADGRJAC2.0*;ADGRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDST4130*;MATTDST8620$DST0097*;MATTDST8620$$DST0097*)
| Table 1 |
| Reply Code (MA01) | Reply |
| STA000 | STEEL |
| ST4130 | STEEL COMP 4130 |
| ST0097 | STEEL COMP 4150H |
| ST8620 | STEEL COMP 8620 |
| ST0672 | STEEL COMP 8653H |
| ST0145 | STEEL COMP 8660H |
| STB000 | STEEL CORROSION RESISTING |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) AAQ WERE ENTERED FOR MRC ARQS, YOU MUST ANSWER MRC (ABHP and ABKV)
IF STYLE/REPLY CODE(s) AAS WERE ENTERED FOR MRC ARQS, YOU MUST ANSWER MRC (ABHP and ABKV and AARX)
ARQSDCONSTRUCTION
THE STRUCTURAL CHARACTERISTIC OF THE ITEM. PLEASE USE MRC CQCF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ARQSDAAS)
| Table 1 |
| Reply Code (AL59) | Reply |
| AAQ | SOLID |
| AAS | TUBULAR |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAA2.0*;ABKVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAC2.0*;AARXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) BCZ WERE ENTERED FOR MRC CFGQ, YOU MUST ANSWER MRC (CFGR and CFGS and CFGT and AMDS and CFGW)
IF STYLE/REPLY CODE(s) AHH OR ASL WERE ENTERED FOR MRC CFGQ, YOU MUST ANSWER MRC (ACKY and AMCX)
CFGQDFIRST END CROSS-SECTIONAL SHAPE
THE GEOMETRIC CONFIGURATION OF THE FIRST END WHEN VIEWED IN CROSS SECTION.
Enter the applicable reply code from the table below
(CFGQDBCZ)
| Table 1 |
| Reply Code (AD07) | Reply |
| AHH | HEXAGON |
| AQF | ROUND W/FLATTED SIDES |
| BCZ | SERRATED |
| ASL | SQUARE |
| TAA | THREADED |
CFGR*AFIRST END TEETH QUANTITY
THE NUMBER OF TEETH PROVIDED AT THE FIRST END.
Enter the numeric reply with a minimum of one digit.
(CFGRA10*)
CFGS*JFIRST END SERRATION LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SERRATION AT THE FIRST END,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFGSJAB2.0*;CFGSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFGT*JFIRST END MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTERMOST SURFACE OF THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFGTJAB2.0*;CFGTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMDS*JFIRST END PITCH DIAMETER
A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE FIRST END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMDSJAA2.0*;AMDSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFGW*BFIRST END PRESSURE ANGLE IN DEG
THE PRESSURE ANGLE OF THE FIRST END,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CFGWB2.0)
ACKY*JFIRST END WIDTH ACROSS FLATS
THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE FIRST END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKYJAC2.0*;ACKYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMCX*JFIRST END FLAT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLAT AT THE FIRST END,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMCXJAB2.0*;AMCXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) BCZ WERE ENTERED FOR MRC CFGX, YOU MUST ANSWER MRC (CFGY and CFGZ and CFHB and AMGF and CFHC)
IF STYLE/REPLY CODE(s) AHH OR ASL WERE ENTERED FOR MRC CFGX, YOU MUST ANSWER MRC (CFHD and AMFP)
CFGXDSECOND END CROSS-SECTIONAL SHAPE
THE GEOMETRIC CONFIGURATION OF THE SECOND END WHEN VIEWED IN CROSS SECTION.
Enter the applicable reply code from the table below
(CFGXDAHH)
| Table 1 |
| Reply Code (AD07) | Reply |
| AHH | HEXAGON |
| BCZ | SERRATED |
| ASL | SQUARE |
| TAA | THREADED |
CFGY*ASECOND END TEETH QUANTITY
THE NUMBER OF TEETH PROVIDED AT THE SECOND END.
Enter the numeric reply with a minimum of one digit.
(CFGYA10*)
CFGZ*JSECOND END SERRATION LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF SERRATION AT THE SECOND END,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFGZJAC2.0*;CFGZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFHB*JSECOND END MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE OUTERMOST SURFACE OF THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHBJAB2.0*;CFHBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMGF*JSECOND END PITCH DIAMETER
A MEASUREMENT INDICATING THE DIAMETER-PITCH PER MEASUREMENT SCALE OF THE SECOND END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMGFJAA2.0*;AMGFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFHC*BSECOND END PRESSURE ANGLE IN DEG
THE PRESSURE ANGLE OF THE SECOND END,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CFHCB2.0)
CFHD*JSECOND END WIDTH ACROSS FLATS
THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE SECOND END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHDJAB2.0*;CFHDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMFP*JSECOND END FLAT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE FLAT AT THE SECOND END,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMFPJAB2.0*;AMFPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) DX WERE ENTERED FOR MRC CFHF, YOU MUST ANSWER MRC (AQSQ and AQSR and AMER and ACLK and ACLL)
IF STYLE/REPLY CODE(s) PQ WERE ENTERED FOR MRC CFHF, YOU MUST ANSWER MRC (AMDX and AMEB)
CFHF*DSOLID BAR END CHARACTERISTIC AT FIRST END
INDICATES THE PHYSICAL CHARACTERISTIC OF THE END OF THE SOLID BAR AT THE FIRST END.
Enter the applicable reply code from the table below
(CFHFDCN)
| Table 1 |
| Reply Code (AB76) | Reply |
| CN | PLAIN |
| DX | THREADED HOLE |
| PQ | UNTHREADED HOLE |
AQSQ*AFIRST END THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH OF THE FIRST END.
Enter the alpha-numeric reply with a minimum of one character.
(AQSQAA1)
AQSR*DFIRST END THREAD SERIES/TYPE DESIGNATOR
DESIGNATES THE SERIES/TYPE OF THE THREADS OF THE FIRST END.
Enter the applicable reply code from the table below
(AQSRDNP)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| SM | ISO M |
| SS | ISO S |
| NP | NPT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NS | UNS |
AMER*JFIRST END INTERNAL THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ INTERNAL THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE FIRST END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMERJAB2.0*;AMERJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLK*AFIRST END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACLKAR0)
ACLL*DFIRST END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACLLDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AMDX*JFIRST END HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE OR BODY OF THE FIRST END,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMDXJAC2.0*;AMDXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMEB*JFIRST END HOLE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE AT THE FIRST END,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMEBJAC2.0*;AMEBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) DX WERE ENTERED FOR MRC CFHG, YOU MUST ANSWER MRC (AQSS and AQST and AMHP and ACMR and ACMS)
IF STYLE/REPLY CODE(s) PQ WERE ENTERED FOR MRC CFHG, YOU MUST ANSWER MRC (AMGS and AMHD)
CFHG*DSOLID BAR END CHARACTERISTIC AT SECOND END
INDICATES THE PHYSICAL CHARACTERISTIC OF THE END OF THE SOLID BAR AT THE SECOND END.
Enter the applicable reply code from the table below
(CFHGDCN)
| Table 1 |
| Reply Code (AB76) | Reply |
| CN | PLAIN |
| DX | THREADED HOLE |
| PQ | UNTHREADED HOLE |
AQSS*ASECOND END THREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER INCH OF THE SECOND END.
Enter the alpha-numeric reply with a minimum of one character.
(AQSSAA1)
AQST*DSECOND END THREAD SERIES/TYPE DESIGNATOR
DESIGNATES THE SERIES/TYPE OF THE THREADS OF THE SECOND END.
Enter the applicable reply code from the table below
(AQSTDNC)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| SM | ISO M |
| SS | ISO S |
| NP | NPT |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NS | UNS |
AMHP*JSECOND END INTERNAL THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF COMPLETE /FULL/ INTERNAL THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE SECOND END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMHPJAA2.0*;AMHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMR*ASECOND END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACMRAL3)
ACMS*DSECOND END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACMSDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
AMGS*JSECOND END HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE OR BODY OF THE SECOND END,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMGSJAC2.0*;AMGSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AMHD*JSECOND END HOLE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF THE HOLE AT THE SECOND END,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AMHDJAC2.0*;AMHDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AQHT, YOU MUST ANSWER MRC (CFHM and CFHN and CFHP)
AQHTDCOVER
AN INDICATION OF WHETHER OR NOT A COVER IS PROVIDED.
Enter the applicable reply code from the table below
(AQHTDB)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
CFHM*JCOVER OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COVER,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHMJAB2.0*;CFHMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFHN*JCOVER OVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE COVER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHNJAB2.0*;CFHNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CFHP*JBAR END TO COVER LARGEST LENGTH
A MEASUREMENT OF THE LARGEST DIMENSION FROM THE END OF THE BAR TO THE COVER,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CFHPJAA2.0*;CFHPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPRA000*;SFTTDPNA001$DAAA000*;SFTTDPNA001$$DAAA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| PNA001 | PAINT MIL-DTL 64159 |
| AAA000 | PAINTED |
| PRA000 | PRIMER |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDGR0492*;HUESDGR0492$DGR0492*;HUESDGR0492$$DGR0492*)
| Table 1 |
| Reply Code (AD06) | Reply |
| GR0492 | GREEN 383, 34094 |
IF YOU ANSWER MRC HDCL, YOU MUST ANSWER MRC (HUES)
HDCL*JCOLOR DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,MANUFACTURERS REFERENCE,OR INDEX SYSTEM AND THE CLASIFICATION DESIGNATION, USED TO IDENTIFY COLOR, COLOR SELECTION, COLOR MATCHING AND QUALITY CONTROL OF A SPECIFIC COLOR.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(HDCLJEATEXT1234*;HDCLJEATEXT1234$$JEATEXT1234*;HDCLJEATEXT1234$JEATEXT1234*;HDCL1BJEATEXT1234*;HDCL1BJEATEXT1234$$JEATEXT1234*;HDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP93) | Reply |
| M | 10TH COLOR RESPONSE |
| N | 11TH COLOR RESPONSE |
| P | 12TH COLOR RESPONSE |
| Q | 13TH COLOR RESPONSE |
| R | 14TH COLOR RESPONSE |
| S | 15TH COLOR RESPONSE |
| T | 16TH COLOR RESPONSE |
| U | 17TH COLOR RESPONSE |
| W | 18TH COLOR RESPONSE |
| X | 19TH COLOR RESPONSE |
| B | 1ST COLOR RESPONSE |
| Y | 20TH COLOR RESPONSE |
| Z | 21ST COLOR RESPONSE |
| V | 22ND COLOR RESPONSE |
| C | 2ND COLOR RESPONSE |
| D | 3RD COLOR RESPONSE |
| E | 4TH COLOR RESPONSE |
| F | 5TH COLOR RESPONSE |
| H | 6TH COLOR RESPONSE |
| J | 7TH COLOR RESPONSE |
| K | 8TH COLOR RESPONSE |
| L | 9TH COLOR RESPONSE |
| G | ALL COLOR RESPONSE |
| A | SINGLE COLOR RESPONSE |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information