An item consisting of two or more legs or loops, suspended from a BEAM, HOISTING. The legs are fabricated of chain, rope, webbing, rod, or the like, and may include attachments or built-in loops at the lower ends. The item may also include one or more SPREADER, SLING. Do not use if a more specific name applies.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED21769*)
BQHQJBEAM TO HOISTING APPARATUS ATTACHMENT TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES PROVIDED FOR ATTACHING THE BEAM TO THE HOISTING APPARATUS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(BQHQJAAY2*;BQHQJAAY2$$JAAY3*)
| Table 1 |
| Reply Code (AJ74) | Reply |
| AAN | BRACKET, LIFTING |
| AAP | BRACKET, LIFTING, RIGIDLY ATTACHED TO BEAM |
| AAQ | EYE BOLT |
| AAR | EYE PLATE |
| AAS | HOLE |
| AAT | HOOK |
| AAW | LINK |
| AAX | LUG |
| AAY | LUG, RIGIDLY ATTACHED TO BEAM |
| AAZ | NUT |
| ABA | NUT, EYE RIGIDLY ATTACHED TO BEAM |
| ABB | PIN |
| ABC | RING |
| ABD | RING, RIGIDLY ATTACHED TO BEAM |
| ABE | SHACKLE |
| ABF | SHACKLE PIN HOLE |
| ABG | SHACKLE, RIGIDLY ATTACHED TO BEAM |
| AHF | U BAR, RIGIDLY ATTACHED TO BEAM |
BQHRJBEAM TO LOAD ATTACHMENT TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF FACILITIES PROVIDED FOR ATTACHING THE LOAD TO THE BEAM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(BQHRJML2*;BQHRJML2$$JML3*)
| Table 1 |
| Reply Code (AB47) | Reply |
| MD | CLEVIS |
| CP | HOLE |
| EB | HOOK |
| ME | HOOK, HOIST |
| HG | LOOP |
| MF | LUG |
| MG | LUG, RIGIDLY ATTACHED TO BEAM |
| AC | NUT |
| MH | NUT, EYE RIGIDLY ATTACHED TO BEAM |
| MJ | NUT, SELF LOCKING HOLE |
| WQ | PLATE W/SCREW ASSEMBLY |
| CR | RING |
| MK | SHACKLE |
| ML | WASHER, BEVELED |
| MM | WIRE ROPE ASSEMBLY, SINGLE LEG |
| MN | YOKE |
AJRSJATTACHMENT STYLE DIMENSIONS
THOSE MEASURED DISTANCES WHICH ARE CHARACTERISTIC OF THE ITEM AND ESTABLISH ITS PHYSICAL LIMITS.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJRSJABAGFZ2.0*;AJRSJABAGFZ2.0$$JABAGFZ2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AF96) | Reply |
| AHHD | BALL END DIAMETER |
| AJRE | BEARING SURFACE TO BEARING SURFACE DISTANCE |
| ABXV | BORE DIAMETER |
| AHPF | EYE NARROW END INSIDE RADIUS |
| AHPG | EYE WIDE END INSIDE RADIUS |
| BRGT | FORK HEIGHT |
| AJSD | FORK SPAN WIDTH |
| AARX | INSIDE DIAMETER |
| ADJU | INSIDE LENGTH |
| ADJT | INSIDE WIDTH |
| AJRP | INSIDE WIDTH BETWEEN EYES |
| AHPA | LINK INSIDE WIDTH |
| AHPC | LINK OPENING INSIDE LENGTH |
| AJRK | MAJOR INSIDE WIDTH |
| AJRL | MINOR INSIDE WIDTH |
| ABKV | OUTSIDE DIAMETER |
| ABHP | OVERALL LENGTH |
| AJRD | PIN CENTER TO LEG END DISTANCE |
| ABVV | PIN DIAMETER |
| ANMD | PIVOT HOLE DIAMETER |
| ANME | PIVOT HOLE DISTANCE FROM END |
| AJSE | SLEEVE DIAMETER |
| AGFZ | SPHERICAL BODY DIAMETER |
| AJRW | TAKE-UP LENGTH |
| AHHE | TONGUE WIDTH |
| AJRT | U-BOLT CENTER TO CENTER DISTANCE |
| AJRV | U-BOLT LENGTH |
| AXWM | WIDTH BETWEEN LEGS |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) AASF WERE ENTERED FOR MRC CLSH, YOU MUST ANSWER MRC (ALSB)
CLSHDSLING MATERIAL TYPE
INDICATES THE MATERIAL TYPE OF THE SLING.
Enter the applicable reply code from the table below
(CLSHDAAGP*;CLSHDAASH$DAAGU*;CLSHDAASH$$DAAGU*)
| Table 1 |
| Reply Code (AN48) | Reply |
| AASF | CHAIN |
| AASG | FIBER ROPE |
| AASH | MULTIPLE WIRE ROPE BRAIDED |
| AAGP | NYLON STRAP |
| AASJ | ROD |
| AAGU | STEEL SAE GRADE |
| ABGK | STEEL TUBE |
| ABGL | WEB STRAP |
| AASK | WIRE ROPE |
ALSB*JCHAIN SIZE
DESIGNATES THE SIZE OF THE CHAIN.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALSBJLA2.0*;ALSBJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) EZE WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (BQGX and BQGY)
IF STYLE/REPLY CODE(s) EZF WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (BQGW)
APGFDDESIGN TYPE
INDICATES THE DESIGN TYPE OF THE ITEM.
Enter the applicable reply code from the table below
(APGFDEZF)
| Table 1 |
| Reply Code (AK54) | Reply |
| EZE | LOOP |
| EZF | MULTIPLE LEG |
BQGX*ALOOP QUANTITY
THE NUMBER OF LOOPS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BQGXA10*)
BQGY*JLOOP INSIDE CIRCUMFERENCE
THE DISTANCE AROUND THE INSIDE SURFACE OF THE LOOP.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQGYJMB2.0*;BQGYJMB2.0$$JMB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQGW*GLEG LENGTH AND QUANTITY
A MEASUREMENT OF THE LONGEST DIMENSION OF A LEG,IN DISTINCTION FROM WIDTH,AND THE NUMBER OF EACH.
Enter clear text.
(BQGWGCLEARTEXT)
IF YOU ANSWER MRC BDHD, YOU MUST ANSWER MRC (NMBR)
BDHDDATTACHMENT TYPE
INDICATES THE TYPE OF ATTACHMENT PROVIDED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(BDHD3JACDAGX*;BDHD3JACDAGX$DAFW*;BDHD3JACDAGX$$DAFW*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3JAA | TOP TERMINAL |
| 3JAB | BOTTOM TERMINAL FIRST VARIATION |
| 3JAC | BOTTOM TERMINAL |
| 3JAD | TOP TERMINAL FIRST VARIATION |
| 3JAE | TOP TERMINAL SECOND VARIATION |
| 3JAF | BOTTOM TERMINAL SECOND VARIATION |
| 3JAG | INTERMEDIATE ATTACHMENT |
| 3JAM | BOTTOM ATTACHMENT |
| 3JAN | INTERMEDIATE ATTACHMENT FIRST VARIATION |
| 3JAP | INTERMEDIATE ATTACHMENT SECOND VARIATION |
| 3JAS | AT 3 AND 9 OCLOCK |
| Table 2 |
| Reply Code (AJ74) | Reply |
| ADW | ANCHOR SHACKLE, STYLE 15 |
| AFY | ANCHOR SHACKLE, STYLE 59 |
| AGQ | ANTITOPPLING SHACKLE, STYLE 69 |
| AED | B TYPE END LINK, STYLE 22 |
| AGZ | BALL END, STYLE 76 |
| AFE | BEAD CHAIN FASTENER, STYLE 45 |
| AEE | C TYPE END LINK, STYLE 23 |
| AFZ | CHAIN SHACKLE, STYLE 60 |
| ADL | CHAIN SHACKLE, STYLE 7 |
| ADM | CHAIN SWIVEL, STYLE 8 |
| AEC | CHOKER HOOK, STYLE 21 |
| AEH | CHOKER HOOK, STYLE 26 |
| AGX | CLEVIS EYE AND CONNECTION, STYLE 74 |
| AEA | CLOSED BRIDGE SOCKET, STYLE 19 |
| ADY | CLOSED SOCKET, STYLE 17 |
| AFM | CRESCENT ROPE THIMBLE, STYLE 50 |
| AEF | D TYPE JOINING LINK, STYLE 24 |
| AEJ | DETACHABLE LINK, STYLE 27 |
| AEY | END LAP LINK, STYLE 39 |
| ADH | ENLARGED COMMON LINK, STYLE 4 |
| AFK | EQUALIZING ROPE THIMBLE, STYLE 48 |
| AFL | EQUALIZING ROPE THIMBLE, STYLE 49 |
| AEL | EYE AND EYE TURNBUCKLE, STYLE 29 |
| AEM | EYE AND HOOK TURNBUCKLE, STYLE 30 |
| AET | FEMALE THREADED, ZINCED-IN COUPLING AND PIN, STYLE 36 |
| AHB | FLOUNDER PLATE |
| AFA | GRAB HOOK, REVERSE EYE, STYLE 41 |
| ADK | GRAB HOOK, STYLE 6 |
| ADX | HOIST HOOK, STYLE 16 |
| AEN | HOOK AND HOOK TURNBUCKLE, STYLE 31 |
| AEQ | JAW AND EYE TURNBUCKLE, STYLE 33 |
| AEP | JAW AND HOOK TURNBUCKLE, STYLE 32 |
| AER | JAW AND JAW TURNBUCKLE, STYLE 34 |
| AES | MALE THREADED, ZINCED-IN COUPLING, STYLE 35 |
| AEB | OPEN BRIDGE SOCKET, STYLE 20 |
| ADZ | OPEN SOCKET, STYLE 18 |
| AGE | OVAL EYE AND CONNECTION, STYLE 65 |
| AFW | OVAL ROPE THIMBLE, STYLE 57 |
| AFX | OVAL ROPE THIMBLE, STYLE 58 |
| AFQ | OVAL W/LUGS AND COVER PLATES ROPE THIMBLE, STYLE 53 |
| AFP | OVAL W/LUGS ROPE THIMBLE, STYLE 52 |
| ADF | PEAR SHAPED LINK, STYLE 2 |
| ADE | RECTANGULAR LINK, STYLE 1 |
| AGC | REGULAR HOIST HOOK, STYLE 63 |
| ADG | RING, STYLE 3 |
| AGR | ROUND EYE, STYLE 70 |
| AFB | ROUND HOOK, REVERSE EYE, STYLE 42 |
| AHD | SAFETY HOIST SWIVEL HOOK |
| AEG | SCREW PIN ANCHOR SHACKLE, STYLE 25 |
| AFD | SCREW PIN CHAIN SHACKLE, STYLE 44 |
| AGB | SHOULDER EYE HEAD CLOSURE, STYLE 62 |
| AFC | SLIP HOOK, REVERSE EYE, STYLE 43 |
| ADJ | SLIP HOOK, STYLE 5 |
| ADQ | SNAP CHOKER HOOK, STYLE 11 |
| AEW | SNAP HOOK, STYLE 37 |
| AEX | SNAP HOOK, STYLE 38 |
| AFH | SNAP RING, STYLE 46 |
| AFN | SPLIT OVAL ROPE THIMBLE, STYLE 51 |
| AFR | SPLIT OVAL ROPE THIMBLE, STYLE 54 |
| AFS | SPLIT OVAL ROPE THIMBLE, STYLE 55 |
| AFT | SPLIT OVAL ROPE THIMBLE, STYLE 56 |
| AFJ | SPLIT RING, STYLE 47 |
| ADS | SPLIT TRIANGULAR LINK, STYLE 13 |
| AHC | STRAP RADOME |
| AGH | SWAGING TERMINAL, STYLE 68 |
| AEK | THIMBLE BRACKET, STYLE 28 |
| AHE | THIMBLE W/ROPE CLAMP |
| ADP | TOGGLE, STYLE 10 |
| ADR | TOGGLE, STYLE 12 |
| ADN | TRACE HOOK, STYLE 9 |
| AEZ | TWIN HOOKS, STYLE 40 |
IF STYLE/REPLY CODE(s) CPQ WERE ENTERED FOR MRC ABFF, YOU MUST ANSWER MRC (NMBR and APCS and ABHP and ABMK and ADUM and ADAV)
ABFFDFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDCPQ*;ABFFDCPQ$$DCPQ*)
| Table 1 |
| Reply Code (AB28) | Reply |
| CPQ | SLING SPREADER |
NMBR*AQUANTITY
A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(NMBR3JAPA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3JAA | TOP TERMINAL |
| 3JAB | BOTTOM TERMINAL FIRST VARIATION |
| 3JAC | BOTTOM TERMINAL |
| 3JAD | TOP TERMINAL FIRST VARIATION |
| 3JAE | TOP TERMINAL SECOND VARIATION |
| 3JAF | BOTTOM TERMINAL SECOND VARIATION |
| 3JAG | INTERMEDIATE ATTACHMENT |
| 3JAM | BOTTOM ATTACHMENT |
| 3JAN | INTERMEDIATE ATTACHMENT FIRST VARIATION |
| 3JAP | INTERMEDIATE ATTACHMENT SECOND VARIATION |
| 3JAS | AT 3 AND 9 OCLOCK |
APCS*DADJUSTABILITY
AN INDICATION OF WHETHER OR NOT THE ITEM IS ADJUSTABLE.
Enter the applicable reply code from the table below
(APCSDA)
| Table 1 |
| Reply Code (AB00) | Reply |
| A | ADJUSTABLE |
| C | NONADJUSTABLE |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJLA2.0*;ADAVJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJLB2.0*;ABHPJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUM*JOVERALL THICKNESS
AN OVERALL MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUMJLA2.0*;ADUMJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATT*DMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDSTA000*;MATTDALB000$DSTA000*;MATTDALB000$$DSTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| STA000 | STEEL |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CPWZ*GTHREAD SIZE AND LOCATION
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER MEASUREMENT SCALE AND ITS LOCATION.
Enter clear text.
(CPWZGCLEARTEXT)
CPXB*GSTOCK SIZE AND LOCATION
DESIGNATES THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE STOCK AND ITS LOCATION.
Enter clear text.
(CPXBGCLEARTEXT)
ADVL*JCROSS SECTION OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CROSS SECTION,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVLJAA2.0*;ADVLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADWH*JCROSS-SECTIONAL WIDTH
A MEASUREMENT OF THE CROSS SECTION TAKEN AT RIGHT ANGLES TO THE LENGTH,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADWHJAB2.0*;ADWHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVM*JCROSS-SECTIONAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A CROSS SECTION,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVMJAC2.0*;ADVMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQHK*JLIFTING CAPACITY
THE LIFTING CAPACITY OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQHKJAS2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
BQHL*JBEAM OVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE BEAM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQHLJAA2.0*;BQHLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQHM*JBEAM OVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A BEAM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQHMJAA2.0*;BQHMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQHN*JBEAM OVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE OF A BEAM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQHNJAB2.0*;BQHNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQPH*JBEAM OVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF THE BEAM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BQPHJAC2.0*;BQPHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
ALXZ*GSPECIFIC USAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter clear text.
(ALXZGCLEARTEXT)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
BRHB*GVESSEL CLASS FOR WHICH SUITABLE
THE CLASS OF VESSEL FOR WHICH THE ITEM IS SUITABLE.
Enter clear text.
(BRHBGCLEARTEXT)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAX4)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAK1)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)