An enclosure which includes, mounts, and protects one or more circuit breakers. It is designed for and may include a cover and such accessories as mounting hardware, brackets, and conduit fittings. May include terminal boards and/or bus conductors used as a convenience for terminating the circuit breakers. May include handle tie bars. It is usually used as a load center for the protection of certain electrical devices such as water heaters, motors, and the like, or as a service center for homes or offices. For boxes which include only switches, jacks, fuseholders, terminals and\or terminal boards or fuseholders, or any combination of these devices, See SWITCH BOX; JACK BOX; TERMINAL BOX; and DISTRIBUTION BOX. For boxes designed to mount and protect but do not include circuit breakers, see CIRCUIT BREAKER BOX SUBASSEMBLY. See also NTERCONNECTING CABINET; PANEL, POWER DISTRIBUTION; JUNCTION BOX; and CABINET, ELECTRICAL EQUIPMENT.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED19365*)
IF STYLE/REPLY CODE(s) 1A OR 2A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKV and ABFY)
IF STYLE/REPLY CODE(s) 3A, 4A, 5A OR 6A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABMK and ABKW and ABFY)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL4A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAK1216 | 1A | ROUND, FLUSH MOUNTING |
| AAK1217 | 2A | ROUND, SURFACE MOUNTING |
| AAK1218 | 3A | SQUARE, FLUSH MOUNTING |
| AAK1219 | 4A | SQUARE, SURFACE MOUNTING |
| AAK1220 | 5A | RECTANGULAR, FLUSH MOUNTING |
| AAK1221 | 6A | RECTANGULAR, SURFACE MOUNTING |
ABFY*JOVERALL DEPTH
AN OVERALL MEASUREMENT BETWEEN SPECIFIED POINTS OF AN ITEM,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABFYJAA2.0*;ABFYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAC2.0*;ABKVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDAL6063*;MATTDGSB000$DAL6061*;MATTDGSB000$$DAL6061*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1230 | ALUMINUM ALLOY 1230 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6063 | ALUMINUM ALLOY 6063 |
| CUB000 | COPPER ALLOY |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| PCA000 | PLASTIC |
| PCN000 | PLASTIC PHENOLIC |
| PCW000 | PLASTIC POLYESTER |
| STA000 | STEEL |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1015 | STEEL COMP 1015 |
| ST1018 | STEEL COMP 1018 |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPSA000*;SFTTDPRA000$DXXG000*;SFTTDPRA000$$DXXG000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| XXG000 | BLACK OXIDE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| ENA000 | ENAMEL |
| ENB000 | ENAMEL LUSTERLESS |
| ENF000 | ENAMEL SEMIGLOSS |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PCA000 | PLASTIC |
| PRA000 | PRIMER |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
IF STYLE/REPLY CODE(s) AAZ WERE ENTERED FOR MRC CPLF, YOU MUST ANSWER MRC (AFEP and BFYB)
IF STYLE/REPLY CODE(s) ABC, ABD, ABE, ABF, ABG OR ABH WERE ENTERED FOR MRC CPLF, YOU MUST ANSWER MRC (AFEP)
CPLF*JENTRANCE TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF ENTRANCES PROVIDED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CPLFJABH2*;CPLFJABH2$$JABH3*)
| Table 1 |
| Reply Code (AK60) | Reply |
| ABL | ARMOR CLAMP |
| ABK | CABLE CLAMP |
| ABJ | COMPRESSION FITTING |
| ABC | CONDUIT COUPLING |
| ABG | DOUBLE CONCENTRIC KNOCKOUT |
| ABN | ELECTRICAL CONNECTOR |
| ABH | FIVE CONCENTRIC KNOCKOUT |
| ABF | FOUR CONCENTRIC KNOCKOUT |
| AAE | PREPUNCHED HOLE |
| ABP | RECTANGULAR/SQUARE |
| ABE | SINGLE KNOCKOUT |
| AAL | STUFFING BOX |
| ABA | STUFFING BOX W/CLAMP |
| AAZ | THREADED HUB |
| ABD | TRIPLE CONCENTRIC KNOCKOUT |
| ABM | TROLLEY DUCT |
| AAP | UNTHREADED HUB |
| ABB | WIPING SLEEVE |
AFQJ*JCABLE ENTRANCE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CABLE ENTRANCE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFQJJAA2.0*;AFQJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGTX*JCABLE OPENING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE CABLE OPENING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGTXJAC2.0*;AGTXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGTY*JCABLE OPENING WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE CABLE OPENING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGTYJAC2.0*;AGTYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFEP*DENTRANCE DIAMETER NUMERIC DESIGNATOR
A NUMERIC DESIGNATION WHICH IDENTIFIES THE NOMINAL DIAMETER OF THE ENTRANCE/S/ PROVIDED ON THE ITEM.
Enter the applicable reply code from the table below
(AFEPDBG*;AFEPDBV$$DES*)
| Table 1 |
| Reply Code (AD98) | Reply |
| AB | 0.250 |
| AP | 0.250/0.500 |
| AQ | 0.250/0.500/0.750 |
| AR | 0.250/0.500/0.750/1.000 |
| FW | 0.281 |
| AC | 0.500 |
| AS | 0.500/0.750 |
| AT | 0.500/0.750/1.000 |
| AU | 0.500/0.750/1.000/1.250 |
| AV | 0.500/0.750/1.000/1.250/1.500 |
| AD | 0.656 |
| DE | 0.718 |
| AE | 0.750 |
| AW | 0.750/1.000 |
| AX | 0.750/1.000/1.250 |
| AY | 0.750/1.000/1.250/1.500 |
| AZ | 0.750/1.000/1.250/1.500/2.000 |
| DP | 0.875 |
| AF | 1.000 |
| BA | 1.000/1.250 |
| BB | 1.000/1.250/1.500 |
| BC | 1.000/1.250/1.500/2.000 |
| BD | 1.000/1.250/1.500/2.000/2.500 |
| EA | 1.062 |
| AG | 1.250 |
| BE | 1.250/1.500 |
| BF | 1.250/1.500/2.000 |
| BG | 1.250/1.500/2.000/2.500 |
| BH | 1.250/1.500/2.000/2.500/3.000 |
| AH | 1.500 |
| BJ | 1.500/2.000 |
| BK | 1.500/2.000/2.500 |
| BL | 1.500/2.000/2.500/3.000 |
| BM | 1.500/2.000/2.500/3.000/3.500 |
| ES | 1.750 |
| FX | 1.900 |
| AJ | 2.000 |
| BN | 2.000/2.500 |
| BP | 2.000/2.500/3.000 |
| BQ | 2.000/2.500/3.000/3.500 |
| BR | 2.000/2.500/3.000/3.500/4.000 |
| EX | 2.062 |
| FY | 2.312 |
| FZ | 2.344 |
| AK | 2.500 |
| BS | 2.500/3.000 |
| BT | 2.500/3.000/3.500 |
| BU | 2.500/3.000/3.500/4.000 |
| AL | 3.000 |
| BV | 3.000/3.500 |
| BW | 3.000/3.500/4.000 |
| AM | 3.500 |
| BX | 3.500/4.000 |
| AN | 4.000 |
| GA | 4.500 |
BFYB*JHUB THREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER MEASUREMENT SCALE OF A THREADED HUB. PLEASE USE MRC THDS IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(BFYBJTS2.0*;BFYBJTS2.0$$JTS2.1*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AG | ACME G |
| AN | ANPT |
| BE | BSP.F EXT |
| BT | BSP.F INT |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| SC | NPSC |
| SH | NPSH |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| TR | NPTR |
| TS | NPTS |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
IF STYLE/REPLY CODE(s) AQC, AQD, AQE, AQF, AQG, ACQ, AET, AHF, AMA, BGP OR BQY WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AESL)
IF STYLE/REPLY CODE(s) AQD, AQF, AET, AFA, AHF OR AMA WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AWAZ)
IF STYLE/REPLY CODE(s) AQC, AQE, ABD OR ACQ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AEBV)
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (ABVG and ABTD)
IF STYLE/REPLY CODE(s) ABD OR AFA WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (ABXD and ABKH)
AXGYDMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable reply code from the table below
(AXGYDAQF*;AXGYDAHF$DBGP*;AXGYDAHF$$DBGP*)
| Table 1 |
| Reply Code (AM39) | Reply |
| AQC | BRACKET WITH HOLE |
| AQD | BRACKET WITH THREADED HOLE |
| ABD | BUSHING |
| AMA | CAPTIVE SCREWS |
| ABH | CLAMP |
| AFL | CLIP |
| BQY | D RING |
| AQE | FLANGE W/HOLE |
| AQF | FLANGE WITH THREADED HOLE |
| ABY | SLOT |
| AQG | SNAP SLIDE FASTENER |
| AFA | THREADED BUSHING |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| BGP | TURNLOCK FASTENER |
| ACQ | UNTHREADED HOLE |
AESL*LSTANDARD MOUNTING PATTERN DESIGNATOR
A DESIGNATION OF THE STANDARD MOUNTING FACILITY ARRANGEMENT PROVIDED.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AESLL7C)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAK1249 | 10C | 8 POINT-IRREGULAR |
| AAK1250 | 11C | 8 POINT-RECTANGULAR |
| AAK1240 | 1C | 2 POINT-IN-LINE |
| AAK1241 | 2C | 2 POINT-DIAGONAL |
| AAK1242 | 3C | 4 POINT-DIAMOND |
| AAK1243 | 4C | BOLT CIRCLE |
| AAK1244 | 5C | 3 POINT-TRIANGULAR |
| AAK1245 | 6C | 4 POINT-QUADRILATERAL |
| AAK1246 | 7C | 4 POINT-RECTANGULAR |
| AAK1247 | 8C | 6 POINT-RECTANGULAR |
| AAK1248 | 9C | 6 POINT-IRREGULAR |
ABKR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKRJAB2.0*;ABKRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVJ*BANGLE BETWEEN CENTERLINES OF MOUNTING HOLES IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE HALF INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ABVJB2.0)
AEBW*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBWJAA2.0*;AEBWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJNJAB2.0*;AEJNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFFL*JMOUNTING BOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFFLJAA2.0*;AFFLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFXR*JFIRST CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFXRJAC2.0*;BFXRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFXS*JFIRST CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFXSJAA2.0*;BFXSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFXT*JSECOND CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFXTJAC2.0*;BFXTJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFXW*JSECOND CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO THE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFXWJAA2.0*;BFXWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFXX*JTHIRD CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFXXJAC2.0*;BFXXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BFXY*JTHIRD CENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFXYJAC2.0*;BFXYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AWAZ*JMOUNTING FACILITY THREAD SIZE
THE THREAD SERIES,THREAD MAJOR/MAXIMUM DIAMETER,AND THE NUMBER OF THREADS PER MEASUREMENT SCALE OF THE MOUNTING FACILITY.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(AWAZJNC2.0*;AWAZJNC2.0$$JNC2.1*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AG | ACME G |
| AN | ANPT |
| BE | BSP.F EXT |
| BT | BSP.F INT |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| SC | NPSC |
| SH | NPSH |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| TR | NPTR |
| TS | NPTS |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBVJAA2.0*;AEBVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVGJAB2.0*;ABVGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAC2.0*;ABTDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXD*JBUSHING LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A BUSHING,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXDJAC2.0*;ABXDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKH*JBUSHING DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BUSHING,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKHJAC2.0*;ABKHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AZAF*DLOCKING DEVICE TYPE
INDICATES THE TYPE OF DEVICE USED TO LOCK THE ITEM.
Enter the applicable reply code from the table below
(AZAFDCJ*;AZAFDBQ$DBP*)
| Table 1 |
| Reply Code (AE36) | Reply |
| BP | INTEGRAL COMBINATION LOCK |
| BQ | INTEGRAL KEY LOCK |
| CJ | PADLOCK |
AGEJ*DSYSTEM FOR WHICH DESIGNED
INDICATES THE TYPE OF SYSTEM IN WHICH THE ITEM IS DESIGNED TO BE USED.
Enter the applicable reply code from the table below
(AGEJDBD*;AGEJDBC$DBJ*;AGEJDBC$$DBJ*)
| Table 1 |
| Reply Code (AE81) | Reply |
| BH | FIVE WIRE TWO PHASE |
| BG | FOUR WIRE THREE PHASE |
| BF | FOUR WIRE TWO PHASE |
| BK | THREE WIRE DC |
| BC | THREE WIRE SINGLE PHASE |
| BE | THREE WIRE THREE PHASE |
| BD | THREE WIRE TWO PHASE |
| BJ | TWO WIRE DC |
| BB | TWO WIRE SINGLE PHASE |
BFYC*BMAIN LINE MAXIMUM CURRENT RATING IN AMPS
THE MAXIMUM CURRENT RATING OF THE MAIN LINE,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BFYCB2.0)
BFYD*BMAIN LINE MAXIMUM AC VOLTAGE RATING IN VOLTS
THE MAXIMUM ALTERNATING CURRENT VOLTAGE RATING OF THE MAIN LINE,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BFYDB2.0*;BFYDB2.0$$BM2.0*)
BGJD*BMAIN LINE MAXIMUM DC VOLTAGE RATING IN VOLTS
THE MAXIMUM DIRECT CURRENT VOLTAGE RATING OF THE MAIN LINE,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BGJDB2.0)
BGJH*DGROUND CONNECTION TYPE FOR WHICH DESIGNED
INDICATES THE TYPE OF GROUND CONNECTION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BGJHDAP*;BGJHDAN$DAM*;BGJHDAN$$DAM*)
| Table 1 |
| Reply Code (AG39) | Reply |
| AL | FUSED |
| AM | FUSIBLE |
| AN | INSULATED |
| AP | SOLID |
| AQ | SWITCHED |
BGJLJCIRCUIT BREAKER TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF CIRCUIT BREAKERS PROVIDED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(BGJLJDF2*;BGJLJDF2$$JDF3*)
| Table 1 |
| Reply Code (AC82) | Reply |
| DF | DOUBLE POLE |
| DJ | FIVE POLE |
| DH | FOUR POLE |
| DE | SINGLE POLE |
| DK | SIX POLE |
| DG | TRIPLE POLE |
BGJMBCIRCUIT BREAKER CURRENT RATING IN AMPS
THE MAXIMUM ELECTRICAL CURRENT WHICH THE CIRCUIT BREAKER WILL CARRY WITHOUT INTERRUPTING THE CIRCUIT,EXPRESSED IN AMPERES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BGJMB2.0*;BGJMB2.0$$BM2.0*)
ACSY*JFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE. PLEASE USE MRC TMQY IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ACSYJNQ2*;ACSYJNQ2$$JNQ3*)
| Table 1 |
| Reply Code (AB87) | Reply |
| AF | CAP AND CHAIN |
| CA | CIRCUIT BREAKER |
| PL | CONNECTOR |
| CP | COVER |
| VQ | DIODE |
| DX | DUST CAP |
| CC | FUSE |
| PM | FUSE PULLOUT |
| AL | GASKET |
| AM | GROMMET |
| LJ | HUMIDITY INDICATOR |
| CE | INDICATOR, LIGHT |
| JG | LAMP |
| AN | LOCKNUT |
| PR | PACKING |
| PN | PACKING NUT |
| NQ | POTENTIOMETER |
| PP | RELAY |
| JN | RESISTOR |
| NR | RHEOSTAT |
| GN | SHUNT |
| GT | TERMINAL BOARD |
| PQ | TRANSFORMER |
| VM | TRANSISTOR |
| GY | WIRE LEAD |
ABFE*DHAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION
THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS.
Enter the applicable reply code from the table below
(ABFEDAE*;ABFEDCE$DEJ*;ABFEDCE$$DEJ*)
| Table 1 |
| Reply Code (AB27) | Reply |
| GK | ACID/FUME RESISTANT |
| CQ | ACID/FUME RESISTANT-OIL IMMERSED NEMA TYPE 11 |
| AB | CEMENT TIGHT |
| FS | DRIPTIGHT |
| AC | DRIPTIGHT-NEMA TYPE 2 |
| CF | DUSTPROOF |
| AD | DUSTPROOF-NEMA TYPE 13 |
| DY | DUSTTIGHT |
| AE | DUSTTIGHT-NEMA TYPE 5 |
| CE | EXPLOSION PROOF |
| CS | EXPLOSION PROOF-NEMA TYPE 7A |
| CR | EXPLOSION PROOF-NEMA TYPE 7A, B, C, D |
| CT | EXPLOSION PROOF-NEMA TYPE 7B |
| CW | EXPLOSION PROOF-NEMA TYPE 7C |
| CX | EXPLOSION PROOF-NEMA TYPE 7D |
| CZ | EXPLOSION PROOF-NEMA TYPE 8A |
| CY | EXPLOSION PROOF-NEMA TYPE 8A, B, C, D |
| DA | EXPLOSION PROOF-NEMA TYPE 8B |
| DB | EXPLOSION PROOF-NEMA TYPE 8C |
| DC | EXPLOSION PROOF-NEMA TYPE 8D |
| DE | EXPLOSION PROOF-NEMA TYPE 9E |
| DD | EXPLOSION PROOF-NEMA TYPE 9E, F, G |
| DF | EXPLOSION PROOF-NEMA TYPE 9F |
| DG | EXPLOSION PROOF-NEMA TYPE 9G |
| FX | FIRE RETARDANT |
| CH | FUNGUS RESISTANT |
| AP | GENERAL PURPOSE-NEMA TYPE 1 |
| EB | HERMETICALLY SEALED |
| DV | MOISTURE PROOF |
| CJ | OILTIGHT |
| EM | RAINTIGHT |
| AR | RAINTIGHT-NEMA TYPE 3R |
| EJ | SHOCK PROOF |
| CL | SPRAYTIGHT |
| DZ | SUBMERSIBLE |
| AS | SUBMERSIBLE-NEMA TYPE 6 |
| CN | WATERTIGHT |
| AU | WATERTIGHT-NEMA TYPE 4 |
| DX | WEATHERPROOF |
| AV | WEATHERPROOF-NEMA TYPE 3 |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY*;CBBLDARS$DAADK*;CBBLDARS$$DAADK*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AADK | COVER |
| AADL | FUSE |
| AAGM | INDICATOR LAMPS |
| ARS | MOUNTING CAP AND CHAIN |
| FNY | ROHS DIRECTIVE COMPLIANCE |
| AAGN | WIRING HARNESS |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AAPC*DIDENTIFICATION CODE COLOR
THE APPLICATION OF COLOR OR A SERIES OF COLORS FOR THE EXPRESSED PURPOSE OF IDENTIFYING THE SPECIFIC FUNCTIONAL DESIGN AND/OR THE SYSTEM APPLICATION OF AN ITEM.
Enter the applicable reply code from the table below
(AAPCDGR0000*;AAPCDBL0000$DRE0000*;AAPCDBL0000$$DRE0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| BL0000 | BLACK |
| BU0000 | BLUE |
| GY0000 | GRAY/GREY |
| GR0000 | GREEN |
| RG0000 | ORANGE |
| RE0000 | RED |
| WH0000 | WHITE |
| YE0000 | YELLOW |
ABPX*JMATERIAL THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE MATERIAL,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABPXJAC2.0*;ABPXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAB*;BBRJDAH$DAB*;BBRJDAH$$DAB*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AH | RADIOACTIVE |
AWJN*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWJNJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| BA | GRAMS |
| AJ | KILOGRAMS |
| AN | OUNCES |
| AS | POUNDS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAM*;BBRGDAD$DAE*;BBRGDAD$$DAE*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDB)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
BGJQ*ACIRCUIT BREAKER IDENTIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE CIRCUIT BREAKER.
Enter the alpha-numeric reply with a minimum of one character.
(BGJQAR8)
BGJR*ACIRCUIT BREAKER MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE CIRCUIT BREAKER.
Enter the alpha-numeric reply with five character(s) exactly.
(BGJRAC3R2H)
CDPF*ACIRCUIT BREAKER NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER BY WHICH THE CIRCUIT BREAKER IS IDENTIFIED.
Enter the alpha-numeric reply with a minimum of one character.
(CDPFAP0)
BGJS*ASWITCH IDENTIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE SWITCH.
Enter the alpha-numeric reply with a minimum of one character.
(BGJSAH2)
BGJT*ASWITCH MANUFACTURER CODE
THE IDENTIFYING NUMERIC CODE OF THE ORIGINATOR THAT CONTROLS OR MANUFACTURES THE SWITCH.
Enter the alpha-numeric reply with five character(s) exactly.
(BGJTAU0V2F)
CDPC*ASWITCH NATIONAL STOCK NUMBER
THE NATIONAL STOCK NUMBER BY WHICH THE SWITCH IS IDENTIFIED.
Enter the alpha-numeric reply with a minimum of one character.
(CDPCAG6)
BGJW*AJACK IDENTIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS IDENTIFICATION NUMBER OR SYMBOL USED TO IDENTIFY THE JACK.
Enter the alpha-numeric reply with a minimum of one character.
(BGJWAQ3)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDAGA000$DPDA000*;PRMTDAGA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000E2.0*;PMWTJAUA000E2.0$JAUA000E2.0*;PMWTJAUA000E2.0$$JAUA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPDA0002.0*;PMLCJPDA0002.0$JPDA0002.0*;PMLCJPDA0002.0$$JPDA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAL1)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAC1)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ008*;HZRDDHAZ052$$DHAZ029*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
| HAZ011 | CHROMIUM |
| HAZ029 | LEAD |
| HAZ052 | ZINC |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information