A boltlike item having a concentric hole along the longitudinal centerline which may extend a part or the full length of the item. It has a hole(s) perpendicular to the axis, joining or passing through the concentric hole along the longitudinal centerline. The item is designed to distribute fluid, air, or lubricant through its body to a mating item, such as a CONNECTOR, MULTIPLE, FLUID PRESSURE LINE, bearing(s), bushing(s), or the like. The item must be capable of attaching to a block fitting and/or a tubing line or be designed to accommodate a FITTING, LUBRICATION. Excludes:BOLT, INTERNALLY RELIEVED BODY; BLEEDER VALVE, HYDRAULIC SYSTEM; and BUSHING, MACHINE THREAD. See also PIN, VEHICULAR LEAF SPRING SHACKLE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED18683*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDST0446*;MATTDCU0309$DST1117*;MATTDCU0309$$DST1117*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0079 | COPPER ALLOY 260 |
| CU0304 | COPPER ALLOY 262 |
| CU0080 | COPPER ALLOY 268 |
| CU0081 | COPPER ALLOY 270 |
| CU0272 | COPPER ALLOY 272 |
| CU0274 | COPPER ALLOY 274 |
| CU0302 | COPPER ALLOY 280 |
| CU0330 | COPPER ALLOY 330 |
| CU0305 | COPPER ALLOY 331 |
| CU0332 | COPPER ALLOY 332 |
| CU0335 | COPPER ALLOY 335 |
| CU0340 | COPPER ALLOY 340 |
| CU0088 | COPPER ALLOY 342 |
| CU0306 | COPPER ALLOY 344 |
| CU0307 | COPPER ALLOY 345 |
| CU0308 | COPPER ALLOY 347 |
| CU0309 | COPPER ALLOY 348 |
| CU0310 | COPPER ALLOY 350 |
| CU0089 | COPPER ALLOY 353 |
| CU0090 | COPPER ALLOY 356 |
| CU0091 | COPPER ALLOY 360 |
| CU0370 | COPPER ALLOY 370 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0465 | COPPER ALLOY 465 |
| CU0466 | COPPER ALLOY 466 |
| CU0467 | COPPER ALLOY 467 |
| CU0100 | COPPER ALLOY 482 |
| CU0101 | COPPER ALLOY 485 |
| CU1158 | COPPER ALLOY CU-AL9NI3FE2 |
| NLB000 | NICKEL ALLOY |
| NL0019 | NICKEL ALLOY 502 |
| NL0017 | NICKEL ALLOY R-405 |
| PCA000 | PLASTIC |
| STA000 | STEEL |
| ST1008 | STEEL COMP 1008 |
| ST1010 | STEEL COMP 1010 |
| ST1011 | STEEL COMP 1011 |
| ST1012 | STEEL COMP 1012 |
| ST1013 | STEEL COMP 1013 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1021 | STEEL COMP 1021 |
| ST1022 | STEEL COMP 1022 |
| ST1023 | STEEL COMP 1023 |
| ST1024 | STEEL COMP 1024 |
| ST1025 | STEEL COMP 1025 |
| ST1026 | STEEL COMP 1026 |
| ST1027 | STEEL COMP 1027 |
| ST1029 | STEEL COMP 1029 |
| ST1030 | STEEL COMP 1030 |
| ST1031 | STEEL COMP 1031 |
| ST1033 | STEEL COMP 1033 |
| ST1035 | STEEL COMP 1035 |
| ST1036 | STEEL COMP 1036 |
| ST1037 | STEEL COMP 1037 |
| ST1038 | STEEL COMP 1038 |
| ST1039 | STEEL COMP 1039 |
| ST1040 | STEEL COMP 1040 |
| ST1041 | STEEL COMP 1041 |
| ST1042 | STEEL COMP 1042 |
| ST1043 | STEEL COMP 1043 |
| ST1045 | STEEL COMP 1045 |
| ST1046 | STEEL COMP 1046 |
| ST1048 | STEEL COMP 1048 |
| ST1049 | STEEL COMP 1049 |
| ST1050 | STEEL COMP 1050 |
| ST1051 | STEEL COMP 1051 |
| ST1052 | STEEL COMP 1052 |
| ST1053 | STEEL COMP 1053 |
| ST1055 | STEEL COMP 1055 |
| ST1060 | STEEL COMP 1060 |
| ST1070 | STEEL COMP 1070 |
| ST1078 | STEEL COMP 1078 |
| ST1080 | STEEL COMP 1080 |
| ST1084 | STEEL COMP 1084 |
| ST1085 | STEEL COMP 1085 |
| ST1086 | STEEL COMP 1086 |
| ST1090 | STEEL COMP 1090 |
| ST1095 | STEEL COMP 1095 |
| ST1108 | STEEL COMP 1108 |
| ST1109 | STEEL COMP 1109 |
| ST1110 | STEEL COMP 1110 |
| ST1111 | STEEL COMP 1111 |
| ST1112 | STEEL COMP 1112 |
| ST1113 | STEEL COMP 1113 |
| ST1115 | STEEL COMP 1115 |
| ST1116 | STEEL COMP 1116 |
| ST1117 | STEEL COMP 1117 |
| ST1118 | STEEL COMP 1118 |
| ST1119 | STEEL COMP 1119 |
| ST1120 | STEEL COMP 1120 |
| ST1125 | STEEL COMP 1125 |
| ST1126 | STEEL COMP 1126 |
| ST1132 | STEEL COMP 1132 |
| ST1137 | STEEL COMP 1137 |
| ST1138 | STEEL COMP 1138 |
| ST1139 | STEEL COMP 1139 |
| ST1140 | STEEL COMP 1140 |
| ST1141 | STEEL COMP 1141 |
| ST1144 | STEEL COMP 1144 |
| ST1145 | STEEL COMP 1145 |
| ST1146 | STEEL COMP 1146 |
| ST1151 | STEEL COMP 1151 |
| ST1211 | STEEL COMP 1211 |
| ST1212 | STEEL COMP 1212 |
| ST1213 | STEEL COMP 1213 |
| ST0070 | STEEL COMP 17-22A |
| ST0071 | STEEL COMP 17-4PH |
| ST0202 | STEEL COMP 202 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0268 | STEEL COMP 30321 |
| ST0078 | STEEL COMP 303S |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0305 | STEEL COMP 305 |
| ST0309 | STEEL COMP 309 |
| ST0310 | STEEL COMP 310 |
| ST3140 | STEEL COMP 3140 |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0321 | STEEL COMP 321 |
| ST0347 | STEEL COMP 347 |
| ST0403 | STEEL COMP 403 |
| ST4037 | STEEL COMP 4037 |
| ST0405 | STEEL COMP 405 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST0414 | STEEL COMP 414 |
| ST4140 | STEEL COMP 4140 |
| ST0093 | STEEL COMP 4140H |
| ST0416 | STEEL COMP 416 |
| ST0098 | STEEL COMP 416F |
| ST0420 | STEEL COMP 420 |
| ST0431 | STEEL COMP 431 |
| ST4320 | STEEL COMP 4320 |
| ST4340 | STEEL COMP 4340 |
| ST0105 | STEEL COMP 440A |
| ST0106 | STEEL COMP 440B |
| ST0107 | STEEL COMP 440C |
| ST0446 | STEEL COMP 446 |
| ST4620 | STEEL COMP 4620 |
| ST0272 | STEEL COMP 51410 |
| ST6150 | STEEL COMP 6150 |
| ST8620 | STEEL COMP 8620 |
| ST0137 | STEEL COMP 8620H |
| ST8630 | STEEL COMP 8630 |
| ST0140 | STEEL COMP 8640H |
| ST8735 | STEEL COMP 8735 |
| ST8740 | STEEL COMP 8740 |
| ST0160 | STEEL COMP AC |
| ST0014 | STEEL COMP B1111 |
| ST0015 | STEEL COMP B1112 |
| ST0016 | STEEL COMP B1113 |
| ST0028 | STEEL COMP E4340 |
| ST0043 | STEEL COMP H11 |
| ST0704 | STEEL COMP XM-12 |
| STB000 | STEEL CORROSION RESISTING |
| TLA000 | TELLURIUM |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TT0046 | TITANIUM ALLOY UNS R54520 |
| TT0052 | TITANIUM ALLOY UNS R56400 |
| TT0053 | TITANIUM ALLOY UNS R56401 |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLF and BBKL and BBKM and BBKN and BBKP and BBKY and AAXC and BBKR and AAWX and BBLB and BBKS and BBKT and BBKW and BBLD and ABHP)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLF and BBKL and BBKR and BBKY and AAXC and BBLB and AAWX and BBLD and ABHP)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKS and BBKL and BBKM and BBKY and AAXC and BBLF and BBLB and AAWX and BBLD and ABHP and BBKR)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAWX and BBLD and BBKY and BBKL and AAXC and BBLB and BBLF and BBKR and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLF and AAWX and BBKL and BBKM and BBKY and AAXC and BBLB and BBKR and BBLD and BBKS and ABHP)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLD and BBKR and BBKS and BBKT and BBKY and BBKZ and AAXC and BBLF and BBKL and BBKM and BBKN and BBLB and BBLC and AAWX and ABHP)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKR and BBKS and BBKT and BBKW and BBKY and AAXC and BBLF and BBKL and BBKM and BBKN and BBKP and BBLB and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKR and BBKS and BBLB and BBKY and BBKL and BBLF and AAWX and AAXC and BBKM and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLF and BBKL and AAXC and BBKY and BBKR and BBLB and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and AAWX and BBKP and BBKL and BBKY and AAXC and BBKN and BBKQ and BBKM and BBLB and BBLF and BBKR and BBKS and BBKT and BBKW and BBKX and BBLD and ACLS)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and BBKL and BBKM and BBLB and BBKY and BBKP and BBKN and BBLF and BBKR and BBKS and BBKT and BBKW and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and BBLC and BBLD and BBKL and BBKM and BBKN and BBKP and BBKQ and BBLF and BBLB and BBKY and BBKZ and BBKR and BBKS and BBKT and BBKW and BBKX and AAWX and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 13 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and BBLF and BBKL and BBKM and BBKN and BBKP and BBKQ and BBKY and BBKZ and CPHT and BBLB and BBLC and BBKR and BBKS and BBKT and BBKW and BBKX and BBLD and ABHP and CPHW and ACLS)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and AAWX and BBKY and BBKL and BBKM and BBKN and BBKP and BBLB and BBKR and BBLF and BBKS and BBKT and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and AAWX and BBKR and BBKL and BBKY and BBLF and BBLB and ABHP and BBLD and ACLS)
IF STYLE/REPLY CODE(s) 16 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and BBKR and BBKS and BBKT and BBKY and BBKW and BBLD and BBKN and BBKP and BBLF and AAWX and BBKL and BBKM and ABHP and BBLB and ACLS)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLF and BBKR and BBLB and BBKY and AAXC and BBKL and AAWX and BBLD and ABHP)
IF STYLE/REPLY CODE(s) 18 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAXC and BBKL and BBKM and BBKN and BBKP and BBKY and BBLB and BBLF and BBKR and BBKS and BBKT and BBKW and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLD and AAWX and BBKY and BBKL and BBKM and BBKN and BBKP and AAXC and BBLB and BBLF and BBKR and BBKS and BBKT and BBKW and ABHP)
IF STYLE/REPLY CODE(s) 20 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and AAWX and BBKL and AAXC and BBLF and BBKY and BBLB and BBKR and BBKS and BBLD)
IF STYLE/REPLY CODE(s) 21 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKR and BBKL and BBKY and BBKZ and AAXC and BBLB and BBLC and BBLD and BBLF and ABHP and AAWX)
IF STYLE/REPLY CODE(s) 22 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKL and BBKM and BBKN and BBKT and BBKY and AAXC and BBKR and BBLB and BBLF and BBKS and AAWX and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 23 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and BBLF and BBKL and BBKY and BBKN and BBKP and AAXC and BBLB and BBKZ and BBLC and BBKM and AAWX and BBKR and BBKS and BBKT and BBKW and BBLD)
IF STYLE/REPLY CODE(s) 24 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAWX and BBKY and BBKZ and AAXC and BBLF and BBKL and BBLB and BBLC and BBKR and ABHP and BBLD and ACLS)
IF STYLE/REPLY CODE(s) 25 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and BBKL and BBLB and AAXC and BBKM and BBKY and BBLF and AAWX and BBKR and BBKS and BBLD and ACLS)
IF STYLE/REPLY CODE(s) 26 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKY and BBLB and BBLF and BBKM and BBKN and AAXC and AAWX and BBKL and BBKR and BBKS and BBKT and ABHP and BBLD and ACLS)
IF STYLE/REPLY CODE(s) 27 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBLF and BBKR and BBKY and AAXC and BBKL and BBLB and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 28 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AAWX and BBKY and BBKR and BBLB and AAXC and BBKL and BBKM and BBLD and BBLF and BBKS and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 29 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and BBKR and BBKS and BBKT and BBLF and AAXC and BBKL and BBKM and BBKN and BBLB)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKR and BBKS and BBKT and BBLD and BBKY and BBKZ and AAXC and BBLF and BBKL and BBKM and BBKN and ABHP and BBLB and BBLC and ACLS)
IF STYLE/REPLY CODE(s) 31 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKS and BBLF and BBKL and BBKM and BBKY and AAXC and BBKR and BBLB and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 32 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKR and BBLF and BBKL and BBKY and BBKZ and AAXC and BBLB and BBLC and BBLD and ABHP and ACLS)
IF STYLE/REPLY CODE(s) 33 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (BBKY and BBKZ and BBKL and AAXC and BBLC and BBLF and BBLB and BBLD and ABHP)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL6)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1045 | 1 | RELIEVED |
| AAH1054 | 10 | BODY WRENCHING |
| AAH1055 | 11 | BODY WRENCHING |
| AAH1056 | 12 | BODY WRENCHING |
| AAH1057 | 13 | BODY WRENCHING |
| AAH1058 | 14 | BODY WRENCHING |
| AAH1059 | 15 | PLAIN |
| AAH1060 | 16 | RELIEVED |
| AAH1061 | 17 | PLAIN |
| AAH1062 | 18 | BODY WRENCHING |
| AAH1063 | 19 | RELIEVED |
| AAH1046 | 2 | PLAIN |
| AAH1064 | 20 | PLAIN |
| AAH1065 | 21 | PLAIN |
| AAH1066 | 22 | PLAIN |
| AAH1067 | 23 | RELIEVED |
| AAH1068 | 24 | PLAIN |
| AAH1069 | 25 | PLAIN |
| AAH1070 | 26 | RELIEVED |
| AAH1071 | 27 | BODY WRENCHING |
| AAH1072 | 28 | PLAIN |
| AAH1073 | 29 | RELIEVED |
| AAH1047 | 3 | STEPPED |
| AAH1074 | 30 | RELIEVED |
| AAH1075 | 31 | BODY WRENCHING |
| AAH1076 | 32 | BODY WRENCHING |
| AAH1077 | 33 | PLAIN |
| AAH1048 | 4 | PLAIN |
| AAH1049 | 5 | RELIEVED |
| AAH1050 | 6 | RELIEVED |
| AAH1051 | 7 | RELIEVED |
| AAH1052 | 8 | SHOULDER |
| AAH1053 | 9 | BODY WRENCHING |
AAWX*JCONCENTRIC HOLE DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWXJLC2.0*;AAWXJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAXC*JCONCENTRIC HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAXCJAB2.0*;AAXCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJLA2.0*;ABHPJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKL*JFIRST DIAMETER FROM WRENCHING FEATURE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKLJLC2.0*;BBKLJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKM*JSECOND DIAMETER FROM WRENCHING FEATURE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKMJAB2.0*;BBKMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKN*JTHIRD DIAMETER FROM WRENCHING FEATURE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKNJAC2.0*;BBKNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKP*JFOURTH DIAMETER FROM WRENCHING FEATURE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKPJLA2.0*;BBKPJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKQ*JFIFTH DIAMETER FROM WRENCHING FEATURE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKQJAB2.0*;BBKQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKR*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FIRST DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKRJAB2.0*;BBKRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKS*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF SECOND DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKSJAB2.0*;BBKSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKT*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF THIRD DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKTJLC2.0*;BBKTJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKW*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FOURTH DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKWJAA2.0*;BBKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKX*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF FIFTH DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKXJLC2.0*;BBKXJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKY*JFIRST RADIAL FLUID HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKYJLC2.0*;BBKYJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKZ*JSECOND RADIAL FLUID HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKZJLC2.0*;BBKZJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBLB*JDISTANCE FROM FIRST RADIAL HOLE CENTER TO END OF BOLT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBLBJLC2.0*;BBLBJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBLC*JDISTANCE FROM SECOND RADIAL HOLE CENTER TO END OF BOLT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBLCJAB2.0*;BBLCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBLD*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO BOLT END
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBLDJAA2.0*;BBLDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBLF*JWRENCHING FEATURE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBLFJLC2.0*;BBLFJLC2.0$$JLC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CPHT*JSIXTH DIAMETER FROM WRENCHING FEATURE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CPHTJAB2.0*;CPHTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CPHW*JLENGTH FROM BEARING SURFACE OF WRENCHING FEATURE TO END OF SIXTH DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CPHWJLB2.0*;CPHWJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQFM*JHARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF AN ITEM WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQFMJRBB2.0*;CQFMJRBB2.0$$JRBB2.1*)
| Table 1 |
| Reply Code (AC26) | Reply |
| BH | BRINELL HULTGREN |
| BS | BRINELL STANDARD |
| BT | BRINELL TUNGSTEN CARBIDE |
| RA | ROCKWELL A |
| RB | ROCKWELL B |
| RC | ROCKWELL C |
| RD | ROCKWELL D |
| RF | ROCKWELL F |
| RG | ROCKWELL G |
| RS | ROCKWELL SUPERFICIAL 15-N |
| RU | ROCKWELL SUPERFICIAL 30-N |
| RN | ROCKWELL SUPERFICIAL 45-N |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AA, AC, AE, AG, AR, AV OR AW WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (CQMM)
IF STYLE/REPLY CODE(s) AA WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C14 OR C15 FOR MRC (ACKN)
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C1, C2, C3, C4, C5, C6, C8 OR C16 FOR MRC (ACKN)
IF STYLE/REPLY CODE(s) AE WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C10, C11 OR C13 FOR MRC (ACKN)
IF STYLE/REPLY CODE(s) AV WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C7 FOR MRC (ACKN)
IF STYLE/REPLY CODE(s) AW WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C9 OR C12 FOR MRC (ACKN)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C6 OR C8 FOR MRC (ACKN)
IF STYLE/REPLY CODE(s) AG WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER STYLE/REPLY CODES(s) C2, C6 OR C8 FOR MRC (ACKN)
ACKMDFIRST END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACKMDAW)
| Table 1 |
| Reply Code (AB76) | Reply |
| AW | THREADED EXTERNAL BOSS |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
IF STYLE/REPLY CODE(s) C2, C3, C5, C13 OR C15 WERE ENTERED FOR MRC ACKN, YOU MUST ANSWER MRC (CQPR)
IF STYLE/REPLY CODE(s) C4, C14 OR C16 WERE ENTERED FOR MRC ACKN, YOU MUST ANSWER MRC (ACTK)
ACKN*LFIRST END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACKNLC6)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1085 | C1 | GASKET SEAL COMPRESSION |
| AAH1094 | C10 | PLAIN |
| AAH1095 | C11 | PLAIN |
| AAH1096 | C12 | DOUBLE THREADED SECTION WITH LOCKNUT SEALING |
| AAH1097 | C13 | INVERTED FLARE |
| AAH1098 | C14 | DOUBLE COMPRESSION |
| AAH1099 | C15 | HIGH PRESSURE FLARE |
| AAH1100 | C16 | FLARED TUBE |
| AAH1086 | C2 | INVERTED FLARE |
| AAH1087 | C3 | FLARED |
| AAH1088 | C4 | COMPRESSION |
| AAH1089 | C5 | FLARELESS |
| AAH1090 | C6 | PLAIN |
| AAH1091 | C7 | GASKET SEAL |
| AAH1092 | C8 | GASKET SEAL |
| AAH1093 | C9 | EXTERNAL SEAT FOR GASKET SEAL (BOSS) |
CQPR*JFIRST END SEAT ANGLE
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQPRJRC2.0*;CQPRJRC2.0$$JRC2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACTK*JFIRST END SEAT RADIUS
THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACTKJAC2.0*;ACTKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AN, BA, BF, BR, BS, BW, NP, NT, SF OR SL WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and ACLL and ATKZ)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and CSQH and CWBM and ACLL and ATKZ)
IF STYLE/REPLY CODE(s) SJ OR SK WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and ACLL and ATKZ and CSQH) or (CQYM and ACLL and ATKZ and CWBM) or (CQYM and ACLL and ATKZ and ADRN)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and CQKK and ACLK and ACLL and ATKZ)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and ACLK and ACLL and ATKZ)
IF STYLE/REPLY CODE(s) JS OR NS WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and CQKK and ACLK and ACLL and ATKZ) or (CQYM and CQKK and ADRN and ACLL and ATKZ)
IF STYLE/REPLY CODE(s) FB OR PL WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and ACLL and ATKZ)
IF STYLE/REPLY CODE(s) SM WERE ENTERED FOR MRC CQMM, YOU MUST ANSWER MRC (CQYM and CSQH and ACLL and ATKZ)
CQMM*DFIRST END THREAD SERIES DESIGNATOR
A DESIGNATOR DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CQMMDJS)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BA | BA |
| BF | BSF |
| FB | BSP.F |
| PL | BSP.PL |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| BW | BSW |
| GE | G |
| SM | ISO M |
| EM | M |
| MJ | MJ |
| SF | NPSF |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NS | UNS |
CQYM*JFIRST END NOMINAL THREAD SIZE
THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQYMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQKK*AFIRST END THREAD QUANTITY PER INCH
THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CQKKAG1)
CSQH*BFIRST END THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CSQHB2.0)
ACLK*AFIRST END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACLKAA3)
CWBM*JFIRST END THREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CWBMJEXT2.0*;CWBMJEXT2.0$$JEXT2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
ADRN*JFIRST END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRNJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACLL*DFIRST END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACLLDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ATKZ*JFIRST END THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ATKZJLA2.0*;ATKZJLA2.0$$JLA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AA, AC, AE, AG, AR, AV OR AW WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (CRPF)
IF STYLE/REPLY CODE(s) AA WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C14 OR C15 FOR MRC (ACLT)
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C1, C2, C3, C4, C5, C6, C8 OR C16 FOR MRC (ACLT)
IF STYLE/REPLY CODE(s) AE WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C10, C11 OR C13 FOR MRC (ACLT)
IF STYLE/REPLY CODE(s) AV WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C7 FOR MRC (ACLT)
IF STYLE/REPLY CODE(s) AW WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C9 OR C12 FOR MRC (ACLT)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C6 OR C8 FOR MRC (ACLT)
IF STYLE/REPLY CODE(s) AG WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER STYLE/REPLY CODES(s) C2, C6 OR C8 FOR MRC (ACLT)
ACLS*DSECOND END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACLSDAG)
| Table 1 |
| Reply Code (AB76) | Reply |
| AW | THREADED EXTERNAL BOSS |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
IF STYLE/REPLY CODE(s) C2, C3, C5, C13 OR C15 WERE ENTERED FOR MRC ACLT, YOU MUST ANSWER MRC (CRCN)
IF STYLE/REPLY CODE(s) C4, C14 OR C16 WERE ENTERED FOR MRC ACLT, YOU MUST ANSWER MRC (ACTL)
ACLT*LSECOND END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACLTLC8)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1085 | C1 | GASKET SEAL COMPRESSION |
| AAH1094 | C10 | PLAIN |
| AAH1095 | C11 | PLAIN |
| AAH1096 | C12 | DOUBLE THREADED SECTION WITH LOCKNUT SEALING |
| AAH1097 | C13 | INVERTED FLARE |
| AAH1098 | C14 | DOUBLE COMPRESSION |
| AAH1099 | C15 | HIGH PRESSURE FLARE |
| AAH1100 | C16 | FLARED TUBE |
| AAH1086 | C2 | INVERTED FLARE |
| AAH1087 | C3 | FLARED |
| AAH1088 | C4 | COMPRESSION |
| AAH1089 | C5 | FLARELESS |
| AAH1090 | C6 | PLAIN |
| AAH1091 | C7 | GASKET SEAL |
| AAH1092 | C8 | GASKET SEAL |
| AAH1093 | C9 | EXTERNAL SEAT FOR GASKET SEAL (BOSS) |
CRCN*JSECOND END SEAT ANGLE
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRCNJRA2.0*;CRCNJRA2.0$$JRA2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACTL*JSECOND END SEAT RADIUS
THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACTLJAA2.0*;ACTLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AN, BA, BF, BR, BS, BW, NP, NT, SF OR SL WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and ACMS and ATLF)
IF STYLE/REPLY CODE(s) EM OR MJ WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and CTDX and CXNC and ACMS and ATLF)
IF STYLE/REPLY CODE(s) SJ OR SK WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and ACMS and ATLF and CTDX) or (CRNB and ACMS and ATLF and CXNC) or (CRNB and ACMS and ATLF and ADRP)
IF STYLE/REPLY CODE(s) NJ OR UN WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and CRMX and ACMR and ACMS and ATLF)
IF STYLE/REPLY CODE(s) JC, JE, JF, NC, NE OR NF WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and ACMR and ACMS and ATLF)
IF STYLE/REPLY CODE(s) JS OR NS WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and CRMX and ACMR and ACMS and ATLF) or (CRNB and CRMX and ADRP and ACMS and ATLF)
IF STYLE/REPLY CODE(s) FB OR PL WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and ACMS and ATLF)
IF STYLE/REPLY CODE(s) SM WERE ENTERED FOR MRC CRPF, YOU MUST ANSWER MRC (CRNB and CTDX and ACMS and ATLF)
CRPF*DSECOND END THREAD SERIES DESIGNATOR
A DESIGNATOR DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CRPFDNE)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BA | BA |
| BF | BSF |
| FB | BSP.F |
| PL | BSP.PL |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| BW | BSW |
| SM | ISO M |
| EM | M |
| MJ | MJ |
| SF | NPSF |
| SL | NPSL |
| NP | NPT |
| NT | NPTF |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| JS | UNJS |
| NS | UNS |
CRNB*JSECOND END NOMINAL THREAD SIZE
THE DESIGNATION WHICH IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE NOMINAL THREAD SIZE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRNBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CRMX*ASECOND END THREAD QUANTITY PER INCH
THE NUMBER OF THREADS PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CRMXAM6)
CTDX*BSECOND END THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTDXB2.0)
ACMR*ASECOND END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACMRAA8)
CXNC*JSECOND END THREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CXNCJNTE2.0*;CXNCJNTE2.0$$JNTE2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
ADRP*JSECOND END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRPJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACMS*DSECOND END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACMSDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ATLF*JSECOND END THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ATLFJAA2.0*;ATLFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BGST*JPRESSURE RATING
THE PRESSURE AT WHICH AN ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BGSTJFBB2.0*;BGSTJFBB2.0$$JFBB2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| LM | BAR |
| LG | KILOPASCALS |
| FB | POUNDS PER SQUARE INCH |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1, 2 OR 4 WERE ENTERED FOR MRC BBDF, YOU MUST ANSWER MRC (ASDB)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC BBDF, YOU MUST ANSWER MRC (AASL)
IF STYLE/REPLY CODE(s) 5 OR 6 WERE ENTERED FOR MRC BBDF, YOU MUST ANSWER MRC (AASY and AASL)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC BBDF, YOU MUST ANSWER MRC (ASDB and AATC)
BBDFLWRENCHING FEATURE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE WRENCHING FEATURE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BBDFL5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1078 | 1 | HEXAGON |
| AAH1079 | 2 | SQUARE |
| AAH1080 | 3 | ROUND |
| AAH1081 | 4 | OCTAGON |
| AAH1082 | 5 | DEE |
| AAH1083 | 6 | ROUND WITH WRENCH FLATS |
| AAH1084 | 7 | EXTENDED WASHER |
AASL*JHEAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR HEAD,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASLJAA2.0*;AASLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASY*JDISTANCE FROM CENTERLINE TO FLAT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASYJAA2.0*;AASYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATC*JEXTENDED WASHER DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATCJAC2.0*;AATCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAB2.0*;ASDBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQBC*JMINIMUM TENSILE STRENGTH
THE MAXIMUM RATED LOAD IN TENSION APPLIED IN A LONGITUDINAL DIRECTION,PER UNIT OF CROSS-SECTIONAL AREA,THAT THE MATERIAL CAN WITHSTAND WITHOUT RUPTURE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CQBCJLTEXT1234*)
| Table 1 |
| Reply Code (AN71) | Reply |
| L | KILOPASCALS |
| P | POUNDS PER SQUARE INCH |
IF YOU ANSWER MRC ADDV, YOU MUST ANSWER MRC (BBKK)
ADDV*JCOTTER PIN HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE COTTER PIN HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADDVJLB2.0*;ADDVJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBKK*JDISTANCE FROM BOLT END TO HOLE CENTER
THE DISTANCE MEASURED ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS OF THE BOLT END TO HOLE CENTER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BBKKJAB2.0*;BBKKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY*;CBBLDFNY$$DFNY*)
| Table 1 |
| Reply Code (AN47) | Reply |
| FNY | ROHS DIRECTIVE COMPLIANCE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPHA000*;SFTTDAGA000$DCDA000*;SFTTDAGA000$$DCDA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| AUA000 | GOLD |
| GFA000 | GRAPHITE |
| LQA000 | LACQUER |
| MTB000 | MOLYBDENUM |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| RHA000 | RHODIUM |
| AGA000 | SILVER |
| SNA000 | TIN |
| VAA000 | VARNISH |
| ZNA000 | ZINC |
| AAAAAB | ZINC NICKEL |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDPTA000*;PRMTDAZA000$DIRA000*;PRMTDAZA000$$DIRA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPDA000F2.0*;PMWTJPDA000F2.0$$JPDA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$JPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information