A tubular item designed to remove solid particles from the water passing through it and to be used in water wells and the like. The particle removing section may be constructed of a continuous winding of wire around the outside bars securely mounted on end couplings, perforated pipe, or perforated pipe covered with fabricated brass or wire mesh jackets. Excludes:STRAINER, SUCTION.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED18258*)
IF STYLE/REPLY CODE(s) D1 OR D4 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKV)
IF STYLE/REPLY CODE(s) D2, D3, D5, D6, D7, D8 OR D9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABKV and THSD and CQJX)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLD3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| BF10096 | D1 | WELDED COLLAR END-WELDED PLAIN END |
| BF10092 | D2 | INTERNAL THREADED END-CLOSED END |
| BF10093 | D3 | INTERNAL THREADED END-WELDED PLAIN END |
| BF10094 | D4 | SET SCREW END-CLOSED END |
| BF10091 | D5 | EXTERNAL THREADED END-CLOSED END |
| BF10095 | D6 | EXTERNAL THREADED BOTH ENDS |
| BF10097 | D7 | INTERNAL THREADED BOTH ENDS |
| BF10098 | D8 | EXTERNAL THREADED END-INTERNAL THREADED END |
| BF10099 | D9 | EXTERNAL THREADED END TAPERED END |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAA2.0*;ABKVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADML*AMOUNTING FLANGE BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES IN THE MOUNTING FLANGE.
Enter the numeric reply with a minimum of one digit.
(ADMLA10*)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQQR)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDAM)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| AN | ANPT |
| BA | BA |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BL | BSP.PL EXT |
| BN | BSP.PL INT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| SM | ISO M |
| SS | ISO S |
| NG | NGO |
| SF | NPSF |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ACLL*DFIRST END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACLLDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ACMS*DSECOND END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACMSDAAL)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDST0202*;MATT3AEEDST0202$DCSB000*;MATT3AEEDST0202$$DCSB000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3CKX | FILTERING MEDIUM |
| 3CKY | SCREENING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALD000 | ALUMINA |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL2117 | ALUMINUM ALLOY 2117 |
| AL2219 | ALUMINUM ALLOY 2219 |
| AL3003 | ALUMINUM ALLOY 3003 |
| AL3004 | ALUMINUM ALLOY 3004 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL5005 | ALUMINUM ALLOY 5005 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5056 | ALUMINUM ALLOY 5056 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL5456 | ALUMINUM ALLOY 5456 |
| AL6053 | ALUMINUM ALLOY 6053 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6063 | ALUMINUM ALLOY 6063 |
| AL7075 | ALUMINUM ALLOY 7075 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| AL0028 | ALUMINUM ALLOY A380.0 |
| AL0060 | ALUMINUM ALLOY C355.0 |
| ASA000 | ASBESTOS |
| MSD000 | ASPHALT |
| CNA000 | CARBON |
| CNC000 | CARBON ACTIVATED |
| PPC000 | CARDBOARD |
| CSA000 | CELLULOSE |
| CSB000 | CELLULOSE ACETATE |
| CXB000 | CEMENT PORTLAND |
| CLD000 | CERAMIC |
| MSL000 | CHARCOAL |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU1016 | COPPER ALLOY 2.1030 |
| CU1039 | COPPER ALLOY 2.1050.01 |
| CU1040 | COPPER ALLOY 2.1052.01 |
| CU0264 | COPPER ALLOY 220 |
| CU0074 | COPPER ALLOY 230 |
| CU0076 | COPPER ALLOY 240 |
| CU0079 | COPPER ALLOY 260 |
| CU0304 | COPPER ALLOY 262 |
| CU0080 | COPPER ALLOY 268 |
| CU0081 | COPPER ALLOY 270 |
| CU0272 | COPPER ALLOY 272 |
| CU0274 | COPPER ALLOY 274 |
| CU0302 | COPPER ALLOY 280 |
| CU0330 | COPPER ALLOY 330 |
| CU0305 | COPPER ALLOY 331 |
| CU0332 | COPPER ALLOY 332 |
| CU0335 | COPPER ALLOY 335 |
| CU0340 | COPPER ALLOY 340 |
| CU0088 | COPPER ALLOY 342 |
| CU0306 | COPPER ALLOY 344 |
| CU0307 | COPPER ALLOY 345 |
| CU0308 | COPPER ALLOY 347 |
| CU0309 | COPPER ALLOY 348 |
| CU0310 | COPPER ALLOY 350 |
| CU0089 | COPPER ALLOY 353 |
| CU0090 | COPPER ALLOY 356 |
| CU0091 | COPPER ALLOY 360 |
| CU0370 | COPPER ALLOY 370 |
| CU0098 | COPPER ALLOY 462 |
| CU0099 | COPPER ALLOY 464 |
| CU0465 | COPPER ALLOY 465 |
| CU0466 | COPPER ALLOY 466 |
| CU0467 | COPPER ALLOY 467 |
| CU0100 | COPPER ALLOY 482 |
| CU0101 | COPPER ALLOY 485 |
| CU0103 | COPPER ALLOY 510 |
| CU0624 | COPPER ALLOY 624 |
| CU0148 | COPPER ALLOY 745 |
| CU0150 | COPPER ALLOY 752 |
| CU0152 | COPPER ALLOY 764 |
| CU0157 | COPPER ALLOY 770 |
| CU0172 | COPPER ALLOY 836 |
| CU0202 | COPPER ALLOY 922 |
| CKA000 | CORK |
| CCA000 | COTTON |
| CCB000 | COTTON DUCK |
| MSP000 | DIATOMACEOUS EARTH |
| FBX000 | FELT |
| FBA000 | FIBER |
| FBS000 | FIBER SYNTHETIC |
| WDA000 | FIBERBOARD |
| MSQ000 | FULLERS EARTH |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| MTE000 | GUNMETAL |
| HRE000 | HAIR |
| FBL000 | HEMP |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| FBK000 | JUTE |
| LRA000 | LEATHER |
| LRK000 | LEATHER SHEEPSKIN |
| MGA000 | MAGNESIUM |
| MGB000 | MAGNESIUM ALLOY |
| MTC000 | METAL |
| MTJ000 | METAL NONFERROUS/D |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| NL0019 | NICKEL ALLOY 502 |
| NL0018 | NICKEL ALLOY K-500 |
| NL0017 | NICKEL ALLOY R-405 |
| FBB000 | NYLON |
| PPA000 | PAPER |
| PPJ000 | PAPERBOARD |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCD000 | PLASTIC ACRYLIC |
| PCAX00 | PLASTIC ACRYLONITRILE |
| PCBL00 | PLASTIC ACRYLONITRILE-BUTADIENE-STYRENE (ABS) |
| PCAN00 | PLASTIC CELLULOSE ACETATE |
| PCH000 | PLASTIC EPOXY |
| PCJ000 | PLASTIC MELAMINE |
| PCCB00 | PLASTIC NYLON |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCX000 | PLASTIC POLYETHYLENE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE |
| PCAC00 | PLASTIC POLYPROPYLENE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAH00 | PLASTIC POLYURETHANE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE (PVC) |
| PCBC00 | PLASTIC STYRENE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PCAAX0 | PLASTIC UREA-FORMALDEHYDE |
| PCBA00 | PLASTIC URETHANE |
| PCAQ00 | PLASTIC VINYL CHLORIDE-ACETATE (USE PCAAA0 & PCBD00) |
| PTA000 | PLATINUM |
| WDB000 | PLYWOOD |
| FBC000 | POLYESTER |
| PMB000 | PULP WOOD |
| FBD000 | RAYON |
| RSC000 | RESIN NATURAL |
| RSA000 | RESIN SYNTHETIC |
| MSZ000 | ROCK WOOL |
| RCE000 | RUBBER |
| RCF000 | RUBBER BUNA N |
| RCD000 | RUBBER CHLOROPRENE |
| RCA000 | RUBBER NATURAL |
| RCC000 | RUBBER SILICONE |
| RCB000 | RUBBER SYNTHETIC |
| MST000 | SAND |
| AGA000 | SILVER |
| MSG000 | SPONGE |
| STA000 | STEEL |
| ST0359 | STEEL COMP 1.0120 |
| ST0368 | STEEL COMP 1.0161 |
| ST0822 | STEEL COMP 1.4301 |
| ST1730 | STEEL COMP 1.4302 |
| ST0379 | STEEL COMP 1.4305 |
| ST0824 | STEEL COMP 1.4401 |
| ST2072 | STEEL COMP 1.4404 |
| ST0805 | STEEL COMP 1.4571 |
| ST1005 | STEEL COMP 1005 |
| ST1006 | STEEL COMP 1006 |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1010 | STEEL COMP 1010 |
| ST1011 | STEEL COMP 1011 |
| ST1012 | STEEL COMP 1012 |
| ST1013 | STEEL COMP 1013 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1025 | STEEL COMP 1025 |
| ST1030 | STEEL COMP 1030 |
| ST1035 | STEEL COMP 1035 |
| ST0202 | STEEL COMP 202 |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0180 | STEEL COMP 302B |
| ST0303 | STEEL COMP 303 |
| ST0166 | STEEL COMP 303 PLUS X |
| ST0077 | STEEL COMP 303F |
| ST0078 | STEEL COMP 303S |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0305 | STEEL COMP 305 |
| ST0152 | STEEL COMP 308 |
| ST0309 | STEEL COMP 309 |
| ST0153 | STEEL COMP 309S |
| ST0310 | STEEL COMP 310 |
| ST0154 | STEEL COMP 310S |
| ST0155 | STEEL COMP 314 |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0321 | STEEL COMP 321 |
| ST0323 | STEEL COMP 323 |
| ST0324 | STEEL COMP 324 |
| ST0347 | STEEL COMP 347 |
| ST0348 | STEEL COMP 348 |
| ST0384 | STEEL COMP 384 |
| ST0385 | STEEL COMP 385 |
| ST0403 | STEEL COMP 403 |
| ST0405 | STEEL COMP 405 |
| ST0410 | STEEL COMP 410 |
| ST0414 | STEEL COMP 414 |
| ST0098 | STEEL COMP 416F |
| ST0420 | STEEL COMP 420 |
| ST0429 | STEEL COMP 429 |
| ST0430 | STEEL COMP 430 |
| ST0105 | STEEL COMP 440A |
| ST0106 | STEEL COMP 440B |
| ST0107 | STEEL COMP 440C |
| ST0108 | STEEL COMP 440F |
| ST0446 | STEEL COMP 446 |
| ST0631 | STEEL COMP 631 |
| STB000 | STEEL CORROSION RESISTING |
| SNB000 | TIN |
| WDC000 | WOOD |
| WLA000 | WOOL |
| WL0018 | WOOL COMP 16R1 |
| WL0001 | WOOL COMP F1 |
| WL0004 | WOOL COMP F12 |
| WL0009 | WOOL COMP F5 |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDANA000*;SFTT3AEEDANA000$DCUA000*;SFTT3AEEDANA000$$DCUA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (SF01) | Reply |
| ALB000 | ALUMINUM |
| ANA000 | ANODIZE |
| A | ANY ACCEPTABLE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| ENA000 | ENAMEL |
| IRA000 | IRIDIUM |
| LQA000 | LACQUER |
| PBA000 | LEAD |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PCB000 | PLASTIC POLYTETRAFLUOROETHYLENE |
| AGA000 | SILVER |
| SNA000 | TIN |
| ZNA000 | ZINC |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBLY*;CBBLDBLZ$$DBLQ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BLN | AIR BLEED VALVE |
| BLP | ANTIDRAIN BACK DEVICE |
| AKB | BY-PASS VALVE |
| BLQ | CASE SHUT-OFF VALVE |
| BLR | CLEANING BLADES |
| BLS | DIFFERENTIAL PRESSURE INDICATOR |
| BLT | DIFFERENTIAL PRESSURE RELIEF VALVE |
| BLW | DRAIN COCK |
| BLX | DRAIN PLUG |
| BLY | FLOW CONTROL VALVE |
| BQM | LIFTING BAIL |
| BLZ | MAGNET |
| BMA | MANUAL SHUT-OFF VALVE |
| BMB | SWITCH-OVER VALVE |
| BMC | THERMAL LOCKOUT |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCC2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CD | CUBIC DECIMETERS |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAJ*;BBRGDAD$DAC*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAE*;BBRJDAK$$DAD*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AD | FLAMMABLE |
| AE | FRAGILE |
| AK | MAGNETIC |
| AQ | PILFERABLE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDRTA000$DAZA000*;PRMTDRTA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000E2.0*;PMWTJAUA000E2.0$$JAUA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJIRA0002.0*;PMLCJIRA0002.0$JIRA0002.0*;PMLCJIRA0002.0$$JIRA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ252*;HZRDDHAZ042$$DHAZ285*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ007 | ASPHALT |
| HAZ157 | CHARCOAL |
| HAZ012 | COPPER |
| HAZ092 | MAGNESIUM |
| HAZ252 | NICKEL |
| HAZ285 | PLASTIC |
| HAZ286 | PLATINUM |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information