A straight nonfluid fitting with wrenching facilities on one end and external threads, other than pipe or hose series, on the other end. It has an unthreaded through hole in its axis which may be countersunk and/or counterbored on one or both ends. It is designed to accommodate a shaft, or the like, or used to reinforce a hole in a bulkhead, or the like. For similar items specifically designed for use in a stuffing box, see PACKING NUT. For nonfluid items with an internal thread, see INSERT, SCREW THREAD; or ADAPTER BUSHING. Excludes:REDUCER, BOSS; and items designed to accommodate a tube or tube fitting.
ISAC Reply 3AEE added to MRC AAWY.
ISAC Reply 3HOM added to MRC AAWY.
ISAC Reply 3HON added to MRC AAWY.
ISAC Reply 3HOO added to MRC AAWY.
ISAC Reply 3HOP added to MRC AAWY.
ISAC Reply 3HOQ added to MRC AAWY.
ISAC Reply 3HOU added to MRC AAWY.
ISAC Reply 2AA deleted from MRC AAWY.
ISAC Reply 2AB deleted from MRC AAWY.
ISAC Reply 2AC deleted from MRC AAWY.
ISAC Reply 2BA deleted from MRC AAWY.
ISAC Reply 2BB deleted from MRC AAWY.
ISAC Reply 2BC deleted from MRC AAWY.
ISAC Reply 2CA deleted from MRC AAWY.
ISAC Reply 2CB deleted from MRC AAWY.
ISAC Reply 2CC deleted from MRC AAWY.
ISAC Reply 3AEE added to MRC AAWZ.
ISAC Reply 3HOM added to MRC AAWZ.
ISAC Reply 3HON added to MRC AAWZ.
ISAC Reply 3HOO added to MRC AAWZ.
ISAC Reply 3HOP added to MRC AAWZ.
ISAC Reply 3HOQ added to MRC AAWZ.
ISAC Reply 3HOU added to MRC AAWZ.
ISAC Reply 2AA deleted from MRC AAWZ.
ISAC Reply 2AB deleted from MRC AAWZ.
ISAC Reply 2AC deleted from MRC AAWZ.
ISAC Reply 2BA deleted from MRC AAWZ.
ISAC Reply 2BB deleted from MRC AAWZ.
ISAC Reply 2BC deleted from MRC AAWZ.
ISAC Reply 2CA deleted from MRC AAWZ.
ISAC Reply 2CB deleted from MRC AAWZ.
ISAC Reply 2CC deleted from MRC AAWZ.
ISAC Reply 3AEE added to MRC ADBD.
ISAC Reply 3HOR added to MRC ADBD.
ISAC Reply 3HOS added to MRC ADBD.
ISAC Reply 3HOT added to MRC ADBD.
ISAC Reply 3HOU added to MRC ADBD.
ISAC Reply 2AA deleted from MRC ADBD.
ISAC Reply 2AB deleted from MRC ADBD.
ISAC Reply 2AC deleted from MRC ADBD.
ISAC Reply 2BA deleted from MRC ADBD.
ISAC Reply 2BB deleted from MRC ADBD.
ISAC Reply 2BC deleted from MRC ADBD.
ISAC Reply 3AEE added to MRC AATA.
ISAC Reply 3HOR added to MRC AATA.
ISAC Reply 3HOS added to MRC AATA.
ISAC Reply 3HOT added to MRC AATA.
ISAC Reply 3HOU added to MRC AATA.
ISAC Reply 2AA deleted from MRC AATA.
ISAC Reply 2AB deleted from MRC AATA.
ISAC Reply 2AC deleted from MRC AATA.
ISAC Reply 2BA deleted from MRC AATA.
ISAC Reply 2BB deleted from MRC AATA.
ISAC Reply 2BC deleted from MRC AATA.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED18019*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDST2512*;MATTDAL2017$DST1008*;MATTDAL2017$$DST1008*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2011 | ALUMINUM ALLOY 2011 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0029 | ALUMINUM ALLOY 360.0 |
| AL0031 | ALUMINUM ALLOY 380.0 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CRA000 | CHROMIUM |
| CTB000 | COBALT ALLOY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0233 | COPPER ALLOY 173 |
| CU0091 | COPPER ALLOY 360 |
| CU0099 | COPPER ALLOY 464 |
| CU0104 | COPPER ALLOY 511 |
| CU0111 | COPPER ALLOY 606 |
| CU0115 | COPPER ALLOY 614 |
| CU0122 | COPPER ALLOY 630 |
| CU0129 | COPPER ALLOY 651 |
| CU0131 | COPPER ALLOY 655 |
| CU0172 | COPPER ALLOY 836 |
| CU0195 | COPPER ALLOY 903 |
| CU0209 | COPPER ALLOY 937 |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| FEB000 | IRON CAST |
| FEC000 | IRON MALLEABLE |
| MGB000 | MAGNESIUM ALLOY |
| MNA000 | MANGANESE |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| NL0018 | NICKEL ALLOY K-500 |
| NLC000 | NICKEL SILVER |
| PCA000 | PLASTIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| RCE000 | RUBBER |
| RC0021 | RUBBER SILICONE CLASS Q |
| STA000 | STEEL |
| ST1008 | STEEL COMP 1008 |
| ST1010 | STEEL COMP 1010 |
| ST1012 | STEEL COMP 1012 |
| ST1013 | STEEL COMP 1013 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1021 | STEEL COMP 1021 |
| ST1022 | STEEL COMP 1022 |
| ST1023 | STEEL COMP 1023 |
| ST1025 | STEEL COMP 1025 |
| ST1026 | STEEL COMP 1026 |
| ST1030 | STEEL COMP 1030 |
| ST1035 | STEEL COMP 1035 |
| ST1038 | STEEL COMP 1038 |
| ST1040 | STEEL COMP 1040 |
| ST1117 | STEEL COMP 1117 |
| ST1118 | STEEL COMP 1118 |
| ST1119 | STEEL COMP 1119 |
| ST1215 | STEEL COMP 1215 |
| ST1345 | STEEL COMP 1345 |
| ST0547 | STEEL COMP 135M |
| ST1541 | STEEL COMP 1541 |
| ST2237 | STEEL COMP 2237 |
| ST2512 | STEEL COMP 2512 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0166 | STEEL COMP 303 PLUS X |
| ST0079 | STEEL COMP 303SE |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST2032 | STEEL COMP 30NCD11 |
| ST0316 | STEEL COMP 316 |
| ST0321 | STEEL COMP 321 |
| ST0324 | STEEL COMP 324 |
| ST0347 | STEEL COMP 347 |
| ST4042 | STEEL COMP 4042 |
| ST4047 | STEEL COMP 4047 |
| ST0410 | STEEL COMP 410 |
| ST4130 | STEEL COMP 4130 |
| ST4135 | STEEL COMP 4135 |
| ST4137 | STEEL COMP 4137 |
| ST4140 | STEEL COMP 4140 |
| ST4142 | STEEL COMP 4142 |
| ST0416 | STEEL COMP 416 |
| ST0100 | STEEL COMP 420F |
| ST0284 | STEEL COMP 420FSE |
| ST0172 | STEEL COMP 430FSE |
| ST4340 | STEEL COMP 4340 |
| ST0107 | STEEL COMP 440C |
| ST5140 | STEEL COMP 5140 |
| ST0630 | STEEL COMP 630 |
| ST8640 | STEEL COMP 8640 |
| ST8650 | STEEL COMP 8650 |
| ST0147 | STEEL COMP 8740H |
| ST1894 | STEEL COMP CB 35 |
| ST0028 | STEEL COMP E4340 |
| ST1895 | STEEL COMP FE 37 KB |
| ST1896 | STEEL COMP FE 44 KB |
| ST1859 | STEEL COMP FE-PL48 |
| ST1860 | STEEL COMP FE-PL52 S |
| ST1840 | STEEL COMP S3 |
| ST0187 | STEEL COMP XM-13 |
| ST2016 | STEEL COMP Z6CNU17-08 |
| STB000 | STEEL CORROSION RESISTING |
| ST1917 | STEEL UNS J91153 |
| TTB000 | TITANIUM |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CQJXJNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AJYRJSCREW THREAD LENGTH
A MEASUREMENT OF THE EXTENT OF SCREW THREADS,INCLUDING INCOMPLETE SCREW THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL THREAD AXIS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJYRJAB2.0*;AJYRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDAGA000*;SFTTDRHA000$DCUA000*;SFTTDRHA000$$DCUA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| AUA000 | GOLD |
| GFA000 | GRAPHITE |
| LQD000 | LACQUER ACRYLIC |
| PBA000 | LEAD |
| NLA000 | NICKEL |
| MSK000 | NITRIDE |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PHC000 | PHOSPHATE MANGANESE |
| PHD000 | PHOSPHATE ZINC |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC POLYTETRAFLUOROETHYLENE |
| RHA000 | RHODIUM |
| AGA000 | SILVER |
| SNA000 | TIN |
| ZNA000 | ZINC |
| AAAAAB | ZINC NICKEL |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDNF*;THSDDBY$$DSM*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AM | ACME |
| CJ | BRITISH NONSTANDARD WHITFORM |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| TT | BUTTRESS |
| CM | INTERNATIONAL METRIC FINE THREAD |
| SM | ISO M |
| CN | METRIC |
| MJ | MJ |
| BY | NF |
| AY | SPECIAL |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JE | UNJEF |
| JS | UNJS |
| NS | UNS |
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJEXTTEXT1234*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAA7)
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
BXBR*JHOLE INSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE HOLE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXBRJAB2.0*;BXBRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) EWU WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (BDYS and AAWY and AAWZ)
IF STYLE/REPLY CODE(s) DDZ WERE ENTERED FOR MRC CBBL, YOU MUST ANSWER MRC (BQDD and ADBD and AATA)
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDDDZ*;CBBLDEWU$$DDDZ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| EWU | COUNTERBORE |
| DDZ | COUNTERSUNK |
BDYS*DCOUNTERBORE LOCATION
INDICATES THE LOCATION OF THE COUNTERBORE ON THE ITEM.
Enter the applicable reply code from the table below
(BDYSDBYR*;BDYSDAPK$$DBQB*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| APK | END OPPOSITE DRIVE END |
| BQB | THREADED END |
| BYR | WRENCHING END |
AAWY*JCOUNTERBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWY3HOQJAB2.0*;AAWY3HOQJAB2.0$JAB2.0*;AAWY3HOQJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOM | END OPPOSITE DRIVE END FIRST COUNTERBORE |
| 3HON | END OPPOSITE DRIVE END SECOND COUNTERBORE |
| 3HOO | THREADED END FIRST COUNTERBORE |
| 3HOP | THREADED END SECOND COUNTERBORE |
| 3HOQ | WRENCHING END FIRST COUNTERBORE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWZ*JCOUNTERBORE DEPTH
THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWZ3HOPJAC2.0*;AAWZ3HOPJAC2.0$JAC2.0*;AAWZ3HOPJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOM | END OPPOSITE DRIVE END FIRST COUNTERBORE |
| 3HON | END OPPOSITE DRIVE END SECOND COUNTERBORE |
| 3HOO | THREADED END FIRST COUNTERBORE |
| 3HOP | THREADED END SECOND COUNTERBORE |
| 3HOQ | WRENCHING END FIRST COUNTERBORE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BQDD*DCOUNTERSINK LOCATION
INDICATES THE LOCATION OF THE COUNTERSINK ON THE ITEM.
Enter the applicable reply code from the table below
(BQDDDBQB*;BQDDDBYR$$DBYR*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| BQB | THREADED END |
| BYR | WRENCHING END |
ADBD*JCOUNTERSINK DEPTH
THE MEASUREMENT OF THE PROCESS USED TO ENLARGE PART OF A HOLE,IN DISTINCTION FROM HEIGHT.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADBD3AEEJAB2.0*;ADBD3AEEJAB2.0$JAB2.0*;ADBD3AEEJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOR | THREADED END FIRST COUNTERSINK |
| 3HOS | THREADED END SECOND COUNTERSINK |
| 3HOT | WRENCHING END FIRST COUNTERSINK |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AATA*BCOUNTERSINK ANGLE IN DEG
THE INCLUDED ANGLE OF THE COUNTERSINK,EXPRESSED IN DEGREES.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(AATA3HORB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOR | THREADED END FIRST COUNTERSINK |
| 3HOS | THREADED END SECOND COUNTERSINK |
| 3HOT | WRENCHING END FIRST COUNTERSINK |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
IF STYLE/REPLY CODE(s) APL WERE ENTERED FOR MRC ACSL, YOU MUST ANSWER MRC (ABMZ)
IF STYLE/REPLY CODE(s) AHH, AKT OR ASL WERE ENTERED FOR MRC ACSL, YOU MUST ANSWER MRC (ASDB)
IF STYLE/REPLY CODE(s) ARY WERE ENTERED FOR MRC ACSL, YOU MUST ANSWER MRC (ABGC and AAZT)
ACSL*DWRENCHING FACILITY SHAPE
THE PHYSICAL CONFIGURATION OF THE FACILITY UTILIZED TO ASSEMBLE OR DISASSEMBLE THE ITEM.
Enter the applicable reply code from the table below
(ACSLDAVM*;ACSLDAHH$$DACA*)
| Table 1 |
| Reply Code (AD07) | Reply |
| ACA | CONCAVE |
| AVM | FACE SPANNER |
| AFC | FLAT |
| AHH | HEXAGON |
| AJP | KNURLED |
| AKT | OCTAGONAL |
| ALC | OVAL |
| APL | ROUND |
| BCZ | SERRATED |
| ARY | SLOTTED |
| ASL | SQUARE |
| AVN | WINGED |
ABMZ*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMZJAC2.0*;ABMZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ASDB*JWIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS,PERPENDICULAR TO THE HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ASDBJAB2.0*;ASDBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGC*JSLOT WIDTH
THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGCJAC2.0*;ABGCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAZT*JSLOT DEPTH
THE MEASUREMENT BETWEEN SPECIFIED POINTS OF THE SLOT,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZTJAB2.0*;AAZTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJAA2.0*;ABNMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAGA000*;PRMTDAUA000$$DAGA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| AGA000 | SILVER |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAGA0002.0*;PMLCJAGA0002.0$$JAGA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| AGA000 | SILVER |
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information