A regulator designed to automatically maintain the current and/or voltage output of an engine generator within specified limits, regardless of variation of load or input voltages. May include cutout relay. Does not include items in which regulation is accomplished by transformer action. See also REGULATOR, CURRENT and REGULATOR, VOLTAGE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED17169*)
ANYCBSYSTEM VOLTAGE RATING
THE ELECTRICAL VOLTAGE OF THE SYSTEM FOR WHICH THE ITEM IS DESIGNED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ANYCB2.0)
ANYDDSYSTEM GROUND POLARITY
INDICATES THE TYPE OF GROUND THE ELECTRICAL SYSTEM UTILIZES.
Enter the applicable reply code from the table below
(ANYDDN*;ANYDDP$DN*)
| Table 1 |
| Reply Code (AK22) | Reply |
| N | NEGATIVE |
| P | POSITIVE |
ANYEDVOLTAGE REGULATOR UNIT TYPE
INDICATES THE TYPE OF DEVICE USED TO MAINTAIN A CONSTANT VOLTAGE.
Enter the applicable reply code from the table below
(ANYEDAAB)
| Table 1 |
| Reply Code (AK23) | Reply |
| AAB | CARBON PILE |
| AAC | TRANSISTOR |
| AAG | TRANSISTOR W/WIRE WOUND COIL |
| AAD | WIRE WOUND COIL |
| AAE | WIRE WOUND COIL STEP TYPE |
ANYHAVOLTAGE REGULATOR UNIT QUANTITY
THE NUMBER OF INDIVIDUAL VOLTAGE REGULATOR UNITS CONTAINED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ANYHA10*)
ANPPJOUTPUT VOLTAGE RATING IN VOLTS
THE OUTPUT VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANPPJC2.0*;ANPPJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) AAB OR AAD WERE ENTERED FOR MRC ANYJ, YOU MUST ANSWER MRC (ANYK and ANYP)
ANYJ*DCURRENT REGULATOR UNIT TYPE
INDICATES THE TYPE OF DEVICE USED TO LIMIT THE CURRENT OUTPUT TO THE MAXIMUM SAFE VALUE.
Enter the applicable reply code from the table below
(ANYJDAAF)
| Table 1 |
| Reply Code (AK23) | Reply |
| AAB | CARBON PILE |
| AAD | WIRE WOUND COIL |
| AAF | WIRE WOUND COIL INTEGRAL W/VOLTAGE REGULATOR UNIT |
ANYK*ACURRENT REGULATOR UNIT QUANTITY
THE NUMBER OF INDIVIDUAL CURRENT REGULATOR UNITS CONTAINED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ANYKA10*)
ANYP*JOUTPUT CURRENT RATING IN AMPS
THE CURRENT THE ITEM WILL PERMIT TO PASS,EXPRESSED IN AMPERES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANYPJB2.0*;ANYPJB2.0$$JB2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANYRDCIRCUIT CONTROL DEVICE TYPE
INDICATES THE TYPE OF DEVICE USED TO CLOSE AND OPEN (BREAK) THE CIRCUIT.
Enter the applicable reply code from the table below
(ANYRDAAA*;ANYRDAAE$$DAAD*)
| Table 1 |
| Reply Code (AK24) | Reply |
| AAC | ACTUATING RELAY |
| AAD | CIRCUIT BREAKER |
| AAB | CUTOUT RELAY |
| AAA | SOLID STATE CIRCUIT BOARD |
| AAE | SWITCH |
ANYSJCUT-IN VOLTAGE RATING
THE CUT-IN VOLTAGE/S/ REQUIRED TO CLOSE THE CIRCUIT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANYSJC2.0*;ANYSJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANYX*JCUTOUT VOLTAGE RATING
THE CUTOUT VOLTAGE/S/ REQUIRED TO OPEN /BREAK/ THE CIRCUIT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANYXJA2.0*;ANYXJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANYZ*JCUTOUT CURRENT RATING IN AMPS
THE DISCHARGE /CUTOUT/ CURRENT/S/ REQUIRED TO OPEN /BREAK/ THE CIRCUIT,EXPRESSED IN AMPERES.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANYZJC2.0*;ANYZJC2.0$$JC2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANZBDREVERSE CURRENT OVERLOAD CIRCUIT BREAKER
AN INDICATION OF WHETHER OR NOT A REVERSE CURRENT OVERLOAD CIRCUIT BREAKER IS INCLUDED.
Enter the applicable reply code from the table below
(ANZBDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ANZCDFIELD RELAY UNIT
AN INDICATION OF WHETHER OR NOT A FIELD RELAY UNIT IS INCLUDED.
Enter the applicable reply code from the table below
(ANZCDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDGE*;ADZCDGK$$DGP*)
| Table 1 |
| Reply Code (AA65) | Reply |
| GK | CORROSION RESISTANT |
| GP | FUNGUS RESISTANT |
| GE | HERMETICALLY SEALED |
| CK | SUBMERSIBLE |
| BX | WATERTIGHT |
ALBHDRADIO INTERFERENCE SHIELDING
AN INDICATION OF WHETHER OR NOT SHIELDING AGAINST RADIO INTERFERENCE IS PROVIDED. PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ALBHDC)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
IF STYLE/REPLY CODE(s) GB OR GC WERE ENTERED FOR MRC AARB, YOU MUST ANSWER STYLE/REPLY CODES(s) P FOR MRC (ANZE)
AARBDTERMINAL TYPE
INDICATES THE TYPE OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM. PLEASE USE MRC CSCF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AARBDAABB*;AARBDGB$$DAAHP*)
| Table 1 |
| Reply Code (AA58) | Reply |
| AAHP | BEARING |
| AABB | CLIP |
| GB | CONNECTOR, RECEPTACLE W/EXTERNAL CONTACTS |
| GC | CONNECTOR, RECEPTACLE W/INTERNAL CONTACTS |
| DB | QUICK DISCONNECT, MALE |
| AAHQ | RING |
| BE | SCREW |
| AZ | THREADED STUD |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
AARAATERMINAL QUANTITY
THE NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARAA10*)
IF STYLE/REPLY CODE(s) P WERE ENTERED FOR MRC ANZE, YOU MUST ANSWER MRC (ANZF)
ANZEDTERMINAL ENCASEMENT
AN INDICATION OF WHETHER OR NOT THE TERMINAL(S) IS ENCASED.
Enter the applicable reply code from the table below
(ANZEDP)
| Table 1 |
| Reply Code (AK25) | Reply |
| P | ENCASED |
| M | NOT ENCASED |
ANZF*ACONDUIT CONNECTION QUANTITY
THE NUMBER OF CONDUIT CONNECTION(S) PROVIDED.
Enter the numeric reply with a minimum of one digit.
(ANZFA10*)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (APAS and APBE and APBC)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (APAQ and APBB and ABTD and APAR and APBH and APBJ and APBC)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (APBB and ABTD and ABVG and APAS and APBG and APBC)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (ABVG and ABTD and APAS and APBE and APBF and APBC)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (APAS and ABTB and APBA and APBD and APBE and APBC)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (APAX and APAZ and THDS)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (ABTD and ABVG and APAT and ABTB and ADNY and APAW)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (ADNZ and ADNY and ABTB)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (AFDT and ABTB and AFDS and APAP)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (ABTB and APAK and ADNZ)
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC ADER, YOU MUST ANSWER MRC (ADNY and ABTB)
ADERLMOUNTING STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE MOUNTING.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ADERL10)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAJ1099 | 1 | TWO HOLE |
| AAJ1108 | 10 | SIX SLOTTED HOLES |
| AAJ1109 | 11 | TWO OPEN SLOTS ON A RADIUS |
| AAJ1100 | 2 | THREE HOLE TRIANGULAR |
| AAJ1101 | 3 | FOUR HOLE TRAPEZOID |
| AAJ1102 | 4 | FOUR HOLE RECTANGULAR |
| AAJ1103 | 5 | TWO PLAIN HOLES TWO SLOTTED HOLES |
| AAJ1104 | 6 | THREE STUD TRIANGULAR |
| AAJ1105 | 7 | FOUR HOLES TWO OPEN SLOTS ON A RADIUS |
| AAJ1106 | 8 | TWO SLOTTED HOLES, TWO OPEN SLOTS ON A RADIUS |
| AAJ1107 | 9 | THREE SLOTTED HOLES, THREE OPEN SLOTS ON A RADIUS |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAA2.0*;ABTBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTDJAA2.0*;ABTDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABVG*JMOUNTING SLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE MOUNTING SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABVGJAC2.0*;ABVGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNY*JDISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNYJAB2.0*;ADNYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADNZ*JDISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADNZJAB2.0*;ADNZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDS*JLONGEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDSJAB2.0*;AFDSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDT*JSHORTEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDTJAA2.0*;AFDTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAK*JCENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH AND HOLE ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APAKJAC2.0*;APAKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAP*JVERTICAL DISTANCE BETWEEN HOLES
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APAPJAA2.0*;APAPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAQ*JLONGEST MOUNTING SLOT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APAQJAA2.0*;APAQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAR*JSHORTEST MOUNTING SLOT LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APARJAB2.0*;APARJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAS*JOPEN SLOT WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APASJAB2.0*;APASJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAT*JCENTER TO CENTER DISTANCE BETWEEN SLOTTED HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APATJAC2.0*;APATJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAW*JCENTER TO CENTER DISTANCE BETWEEN SLOTTED HOLES AND PLAIN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APAWJAC2.0*;APAWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAX*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING STUDS ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APAXJAA2.0*;APAXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APAZ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING STUDS ALONG WIDTH AND MOUNTING STUD ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APAZJAC2.0*;APAZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APBA*JCENTER TO CENTER DISTANCE BETWEEN HOLE AND OPEN SLOT ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APBAJAC2.0*;APBAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APBB*JCENTER TO CENTER DISTANCE BETWEEN SLOTS ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APBBJAC2.0*;APBBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APBC*JMOUNTING FACILITY RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(APBCJAA2.0*;APBCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
APBD*BANGLE BETWEEN PLAIN HOLES IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APBDB2.0)
APBE*BANGLE BETWEEN OPEN SLOTS IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APBEB2.0)
APBF*BANGLE BETWEEN SLOTTED HOLES IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APBFB2.0)
APBG*BANGLE BETWEEN SLOTTED HOLES AND OPEN SLOTS IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APBGB2.0)
APBH*BANGLE BETWEEN SHORTEST SLOTTED HOLES IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APBHB2.0)
APBJ*BANGLE BETWEEN LONGEST SLOTTED HOLES IN DEG
NONE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APBJB2.0)
THDS*JTHREAD SIZE AND SERIES/TYPE DESIGNATOR
DESIGNATES THE THREAD DIAMETER,SERIES/TYPE,AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(THDSJNMTEXT1234*)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| NN | NONSTANDARD |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NM | UNM |
| NS | UNS |
AGBCDSHOCK MOUNT
AN INDICATION OF WHETHER OR NOT THE ITEM IS PROVIDED WITH A SELF-CONTAINED SHOCK MOUNT.
Enter the applicable reply code from the table below
(AGBCDB)
| Table 1 |
| Reply Code (AB22) | Reply |
| C | NOT PROVIDED |
| B | PROVIDED |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AWJN*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWJNJAJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJAA2.0*;AJAFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAC2.0*;AJAGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAB2.0*;AJAHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAJ*;BBRGDAK$DAN*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AM | DEHUMIDIFIED WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AJ | UNHEATED WAREHOUSE |
| AK | UNIMPROVED OPEN |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAE*;BBRJDAK$$DAE*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AE | FRAGILE |
| AK | MAGNETIC |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDC)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDRHA000*;PRMTDAZA000$DAUA000*;PRMTDAZA000$$DAUA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJPTA000F2.0*;PMWTJPTA000F2.0$$JPTA000F2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$JPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ027)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ027 | IRIDIUM |
SHPN*ADOT PROPER SHIPPING NAME
THE PROPER SHIPPING NAME AS IDENTIFIED BY THE DEPARTMENT OF TRANSPORTATION (DOT) AND LISTED IN THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE.
Enter the alpha-numeric reply with a minimum of one character.
(SHPNAR0)
DENN*ADOT IDENTIFICATION NUMBER
THE IDENTIFICATION NUMBER ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PROPER SHIPPING NAME. IDENTIFICATION NUMBERS PRECEDED BY THE LETTERS "UN" ARE ASSOCIATED WITH INTERNATIONAL AS WELL AS DOMESTIC TRANSPORTATION AND THOSE PRECEDED BY THE LETTERS "NA" ARE NOT RECOGNIZED FOR INTERNATIONAL TRANSPORTATION OF HAZARDOUS MATERIALS (DANGEROUS GOODS) EXCEPT TO AND FROM THE UNITED STATES AND CANADA.
Enter the alpha-numeric reply with a minimum of one character.
(DENNAA7)
WLBL*ADOT WARNING LABEL CODE
THE WARNING LABEL CODE ASSIGNED BY THE DEPARTMENT OF TRANSPORTATION (DOT) TO EACH PACKAGE OR CONTAINMENT DEVICE OFFERED FOR TRANSPORTATION OF A HAZARDOUS MATERIAL WHICH MEETS ONE OR MORE HAZARD CLASS DEFINITIONS IN ACCORDANCE WITH THE TITLE 49 CODE OF FEDERAL REGULATIONS (CFR), PART 172, HAZARDOUS MATERIALS TABLE. THIS MRC HAS BEEN DISCONTINUED WITH NO REPLACEMENT - THIS INFORMATION IS NOT CHARACTERISTIC INFORMATION, THIS INFORMATION NEEDS TO BE INPUT IN SEG G OF THE TIR.
Enter the alpha-numeric reply with a minimum of one character.
(WLBLAV7)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)