A grease developed to seal mating ground glass joints of a temporary nature on the high vacuum side of laboratory apparatus and to enable the joint to be disassembled readily. Excludes:PETROLATUM, TECHNICAL; and GREASE, LABORATORY STOPCOCK.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED14948*)
CSMBJVAPOR PRESSURE MAXIMUM TEMP RATING
THE MAXIMUM TEMPERATURE OF THE VAPOR PRESSURE FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSMBJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CRWDJEFFECTIVE TEMP RANGE RATING
THE MINIMUM AND MAXIMUM EFFECTIVE TEMPERATURE RATING OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CRWDJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
ARARJMELTING POINT TEMP RATING
THE TEMPERATURE AT WHICH THE ITEM WILL MELT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ARARJF2.0*;ARARJF2.0$JF2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC AGZX, YOU MUST ANSWER MRC (CHFX)
AGZX*DBASIC INGREDIENT
THE PRIMARY INGREDIENT OF WHICH THE ITEM IS MADE.
Enter the applicable reply code from the table below
(AGZXDMW*;AGZXDFT$DFN*;AGZXDFT$$DFN*)
| Table 1 |
| Reply Code (AF11) | Reply |
| HE | 1,1,2,2, -TETRABROMOETHANE |
| FH | ACETYLENE TETRABROMIDE |
| AB | ADDITIVES |
| FE | ALCOHOL |
| FF | ALUMINUM SOAP |
| FG | AN-ESTER-POLYMER-OXIDATION INHIBITOR |
| A | ANY ACCEPTABLE |
| CG | ASPHALT |
| FK | BARIUS SOAP |
| FJ | BROMIDE |
| FL | BROMOFORM |
| FM | BROMOTRIFLUOROETHYLENE-BASE-BLENDED |
| FN | CALCIUM SOAP |
| AR | CASTOR OIL |
| FP | CYLINDER STOCK MINERAL OIL-SODIUM SOAP |
| FQ | DEPROPYLENE GLYCOL METHYL ETHER |
| FR | DIMETHYL SILICONE |
| LT | DISULFIDE |
| LU | EMULSIFIABLE AGENT |
| MS | ETHYLENE GLYCOL |
| FS | FATTY SOAP |
| FT | GELLING AGENT |
| AC | GRAPHITE |
| FU | HYDROCARBONS |
| FX | LEAD SOAP |
| FV | LITHIUM SOAP |
| BG | LUBRICATING OIL |
| FW | LUBRICATING OIL-CALCIUM SOAP |
| FY | LUBRICATING OIL-POLYBUTENE |
| FZ | MAGNESIUM SOAP |
| GA | METALLIC LEAD-ASPHALT-CALCIUM SOAP |
| AD | MINERAL OIL |
| GC | MINERAL OIL-ALUMINUM SOAP |
| GD | MINERAL OIL-BARIUS SOAP |
| GE | MINERAL OIL-CALCIUM SOAP |
| GB | MINERAL OIL-CALCIUM-MAGNESIUM SOAP |
| LV | MINERAL OIL-CHLORINE |
| GF | MINERAL OIL-GELLING AGENT |
| GG | MINERAL OIL-LITHIUM SOAP |
| GH | MINERAL OIL-MOLYBDENUM |
| LW | MINERAL OIL-PHOSPHOROUS |
| GJ | MINERAL OIL-SOAP |
| LX | MINERAL OIL-SULFURIZED |
| GK | MINERAL SEAL OIL |
| GL | NONMINERAL OIL |
| GM | OIL ORGANO-SILICONE |
| GN | PETROLEUM BASE |
| AE | PETROLEUM OIL |
| GP | PETROLEUM OIL-CALCIUM-LEAD SOAP |
| GQ | PETROLEUM TYPE |
| LY | PHOSPHATE ESTER BASE |
| GR | POLYCHLOROTRIFLUOROETHYLENE |
| GS | POLYMER-OF-BROMOTRIFLUOROETHYLENE |
| GT | POLYMETHYLTHENYL SILICONE FLUID-LITHIUM SOAP |
| GU | POTASSIUM |
| GV | SEAL OIL |
| GW | SEBACATE-ESTER BASE |
| GX | SILICATE-ESTER BASE |
| DZ | SILICONE |
| AF | SILICONE FLUID |
| GY | SILICONE FLUID-LITHIUM SOAP |
| BY | SOAP |
| MW | SODIUM MERCAPTOBENZOTHIAZOLE |
| GZ | SODIUM SOAP |
| HA | SYNTHETIC BASE |
| MB | SYNTHETIC OIL |
| AG | SYNTHETICALLY PREPARED OIL |
| HB | TETRABROMOTHANE |
| MT | TRIETHANOLAMINE PHOSPHATE |
| HC | TRIFLUOROVINYL-CHLORIDE |
| HD | VEGETABLE OIL-GLYCEROL-SOAP |
| CB | WATER |
CHFX*BGRAPHITE PERCENTAGE
THE PERCENTAGE OF GRAPHITE IN THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CHFXB2.0)
CTJC*JMINIMUM FLASH POINT AND TEST METHOD
A NUMERIC VALUE OF THE MINIMUM TEMPERATURE AT WHICH THE VAPOR WILL IGNITE,AND THE TEST METHOD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTJCJFAAB2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AL43) | Reply |
| AAK | CLEVELAND OPEN CUP |
| AAB | PENSKY-MARTENS CLOSED CUP |
AJAM*DSERVICE CHARACTERISTICS
THOSE PROTECTIVE OR RESISTIVE QUALITIES THAT ARE INDICATIVE OF THE INTENDED SERVICE OF THE ITEM.
Enter the applicable reply code from the table below
(AJAMDBM*;AJAMDAK$DAX*;AJAMDAK$$DAX*)
| Table 1 |
| Reply Code (AF60) | Reply |
| AR | ACID RESISTANT |
| AS | ALCOHOL RESISTANT |
| AT | ALKALI RESISTANT |
| AB | ANTIFOAM |
| AC | ANTIWEAR |
| A | ANY ACCEPTABLE |
| AU | CHLORINE RESISTANT |
| AD | CORROSION RESISTIVE |
| AF | DEODORANT |
| AE | DETERGENT |
| AG | EXTREME PRESSURE |
| AV | FUEL-OIL RESISTIVE |
| AW | GASOLINE-FUEL OIL RESISTIVE |
| BM | HEAT TRANSFER MEDIUM |
| AH | HIGH TEMPERATURE |
| AX | LOW EVAPORATION |
| AJ | LOW TEMPERATURE |
| AY | LOW VOLATILITY |
| BN | NONCORROSIVE |
| AZ | NONSLICK |
| BP | NONTOXIC |
| AK | OILINESS |
| BA | ORGANIC SOLVENTS RESISTIVE |
| AL | OXIDATION RESISTANT |
| BB | PETROLEUM SOLVENTS RESISTIVE |
| BQ | RADIATION RESISTANT |
| AM | SALT WATER RESISTANT |
| BC | TAR-PITCH-ASPHALT |
| AN | WATER RESISTANT |
| BD | WATER SEALING |
| BE | WEAR RESISTANT |
IF STYLE/REPLY CODE(s) AAB WERE ENTERED FOR MRC AGXW, YOU MUST ANSWER MRC (DMTR and LGTH)
IF STYLE/REPLY CODE(s) AAB WERE ENTERED FOR MRC AGXW, YOU MUST NOT ANSWER MRC (AKKF)
AGXW*DPHYSICAL FORM
THE RECOGNIZED SHAPE, CONFIGURATION, STRUCTURE, OR MOLD OF A SUBSTANCE, NATURAL OR REFINED, THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Enter the applicable reply code from the table below
(AGXWDAAAN)
| Table 1 |
| Reply Code (AE98) | Reply |
| A | ANY ACCEPTABLE |
| AAAL | LIQUID |
| AAAN | PASTE |
| AAAM | POWDER |
| AACK | SOLID |
| AAB | STICK |
| AAAK | TUBE |
DMTR*JDIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(DMTRJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
LGTH*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(LGTHJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AKKF*JQUANTITY WITHIN EACH UNIT PACKAGE
THE NUMBER OF THE VOLUME,FORM,OR THE DOSAGE WITHIN EACH UNIT PACKAGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AKKFJAR2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| FK | GALLON, IMPERIAL MEASURE |
| AF | GALLONS |
| BA | GRAMS |
| AJ | KILOGRAMS |
| CC | LITERS |
| DG | OUNCES, AVOIRDUPOIS |
| DH | OUNCES, FLUID |
| FM | PINT, IMPERIAL MEASURE |
| AR | PINTS |
| AS | POUNDS |
| FP | QUART, IMPERIAL MEASURE |
| AT | QUARTS |
IF YOU ANSWER MRC HDCL, YOU MUST ANSWER MRC (HUES)
HDCL*JCOLOR DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,MANUFACTURERS REFERENCE,OR INDEX SYSTEM AND THE CLASIFICATION DESIGNATION, USED TO IDENTIFY COLOR, COLOR SELECTION, COLOR MATCHING AND QUALITY CONTROL OF A SPECIFIC COLOR.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(HDCLJEATEXT1234*;HDCLJEATEXT1234$$JEATEXT1234*;HDCLJEATEXT1234$JEATEXT1234*;HDCL1BJEATEXT1234*;HDCL1BJEATEXT1234$$JEATEXT1234*;HDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP93) | Reply |
| M | 10TH COLOR RESPONSE |
| N | 11TH COLOR RESPONSE |
| P | 12TH COLOR RESPONSE |
| Q | 13TH COLOR RESPONSE |
| R | 14TH COLOR RESPONSE |
| S | 15TH COLOR RESPONSE |
| T | 16TH COLOR RESPONSE |
| U | 17TH COLOR RESPONSE |
| W | 18TH COLOR RESPONSE |
| X | 19TH COLOR RESPONSE |
| B | 1ST COLOR RESPONSE |
| Y | 20TH COLOR RESPONSE |
| Z | 21ST COLOR RESPONSE |
| V | 22ND COLOR RESPONSE |
| C | 2ND COLOR RESPONSE |
| D | 3RD COLOR RESPONSE |
| E | 4TH COLOR RESPONSE |
| F | 5TH COLOR RESPONSE |
| H | 6TH COLOR RESPONSE |
| J | 7TH COLOR RESPONSE |
| K | 8TH COLOR RESPONSE |
| L | 9TH COLOR RESPONSE |
| G | ALL COLOR RESPONSE |
| A | SINGLE COLOR RESPONSE |
HUES*DCOLOR
A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.
Enter the applicable reply code from the table below
(HUESDCL0000*;HUESDRE0000$DAM0000*)
| Table 1 |
| Reply Code (AD06) | Reply |
| AM0000 | AMBER |
| A | ANY ACCEPTABLE |
| BU0000 | BLUE |
| CL0000 | CLEAR |
| CL0001 | COLORLESS |
| GR0000 | GREEN |
| PU0000 | PURPLE |
| RE0000 | RED |
| WH0000 | WHITE |
| YE0000 | YELLOW |
CHGL*DGREASE TYPE
INDICATES THE TYPE OF GREASE PROVIDED.
Enter the applicable reply code from the table below
(CHGLDBJM*;CHGLDAEB$DCAH*;CHGLDAEB$$DCAH*)
| Table 1 |
| Reply Code (AM39) | Reply |
| AEB | CHASSIS |
| CAH | ELECTRICALLY CONDUCTIVE |
| BJK | OPEN GEAR COMPOUND |
| BJM | WATER PUMP |
| BJN | WHEEL BEARING |
AEHZ*JMAXIMUM OPERATING TEMP
THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS RATED TO OPERATE FOR AN EXTENDED PERIOD OF TIME.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHZJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CQJS*JMINIMUM DROPPING POINT
THE LOWEST TEMPERATURE AT WHICH THE ITEM WILL DROP.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJSJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBFV)
| Table 1 |
| Reply Code (AN47) | Reply |
| BFV | BIODEGRADABLE |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
IF STYLE/REPLY CODE(s) AT, AZ, BD, BH, BP, BU, BX, CA, KQ, KR OR KS WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (ALAX)
IF STYLE/REPLY CODE(s) EB WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (PTRM)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDEB)
| Table 1 |
| Reply Code (EN02) | Reply |
| AT | 2-CYCLE ENGINE OILS - BIOBASED |
| EB | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - RE-REFINED LUBRICATING OILS |
| KS | DIESEL FUEL ADDITIVES - BIOBASED |
| AZ | FIREARM LUBRICANTS - BIOBASED |
| BD | GREASES - FOOD GRADE - BIOBASED |
| BH | GREASES - GENERAL - BIOBASED |
| BP | GREASES - MULTIPURPOSE - BIOBASED |
| BU | GREASES - RAIL TRACK - BIOBASED |
| CA | GREASES - TRUCK - BIOBASED |
| KQ | HYDRAULIC FLUIDS - MOBILE EQUIPMENT - BIOBASED |
| BX | HYDRAULIC FLUIDS - STATIONARY EQUIPMENT - BIOBASED |
| KR | PENETRATING LUBRICANTS - BIOBASED |
ALAX*BBIOBASED CONTENT PERCENTAGE
THE STATED PERCENTAGE OF THE ITEM'S CONTENT THAT IS BIOBASED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALAXB2.0)
PTRM*BTOTAL RECOVERED MATERIALS PERCENTAGE
THE PERCENTAGE OF THE TOTAL RECOVERED OR RECYCLED MATERIAL, FROM MANUFACTURING PROCESSES OR CONSUMER, INCLUDED IN THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(PTRMB2.0)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CF | CUBIC FEET |
| CN | CUBIC INCHES |
| CM | CUBIC METERS |
CQMJ*ADRUM MATERIAL GAGE NUMBER
THE STANDARD DESIGNATION USED TO INDICATE THE THICKNESS OF THE DRUM MATERIAL.
Enter the alpha-numeric reply with a minimum of one character.
(CQMJAJ8)
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAW*;BBRGDAT$DAX*;BBRGDAT$$DAX*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AT | DOCK LEVEL HEATED WAREHOUSE |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AY | GENERAL PURPOSE HEATED WAREHOUSE |
| AZ | GENERAL PURPOSE UNHEATED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AS | GROUND LEVEL HEATED WAREHOUSE |
| AW | GROUND LEVEL UNHEATED WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AL | TEMPERATURE CONTROLLED WAREHOUSE |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CSGW*ANATO CODE NUMBER
THE DESIGNATOR WHICH IS ASSIGNED TO THE PRODUCT BY THE NATO MILITARY AGENCY FOR STANDARDIZATION(MAS).
Enter the alpha-numeric reply with a minimum of one character.
(CSGWAF7)
CLGK*AMILITARY SYMBOL
THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MILITARY NUMBER.
Enter the alpha-numeric reply with a minimum of one character.
(CLGKAU7)
EPPC*DENVIRONMENTALLY PREFERRED PRODUCT CERTIFICATION TYPE
INDICATES THE TYPE OF CERTIFICATION INDICATING THE ITEM IS AN ENVIRONMENTALLY PREFERRED PRODUCT.
Enter the applicable reply code from the table below
(EPPCDAA*;EPPCDAB$$DAB*)
| Table 1 |
| Reply Code (EN01) | Reply |
| AA | THIRD PARTY CERTIFICATION |
| AB | UNVERIFIED SELF-CERTIFICATION |
ENVA*DENVIRONMENTAL ATTRIBUTE
THE SPECIFIC ATTRIBUTE OF THE ITEM THAT QUALIFIES IT AS AN ENVIRONMENTALLY PREFERABLE PRODUCT.
Enter the applicable reply code from the table below
(ENVADAAG*;ENVADAAS$$DAAS*)
| Table 1 |
| Reply Code (EN00) | Reply |
| AAG | CONTAINS RECYCLED MATERIAL |
| AAS | RECYCLABLE |
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ355*;HZRDDHAZ007$$DHAZ356*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ355 | ACETYLENE TETRABROMIDE |
| HAZ007 | ASPHALT |
| HAZ144 | BROMOFORM |
| HAZ043 | ETHYLENE GYLCOL |
| HAZ356 | PETROLEUM OIL |
| HAZ033 | POTASSIUM |
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information