An item designed to be attached to a segment or a complete lining. It is usually designed to be fastened to a shoe,disk,band,cone,or the like, but may be installed without fastening. It provides a friction surface for transmitting,retarding,or stopping motion. Exclude: LINING MATERIAL,FRICTION.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED11405*)
IF STYLE/REPLY CODE(s) ASA000 WERE ENTERED FOR MRC MATT, YOU MUST ANSWER MRC (AARN)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDTTB000*;MATT3AEEDTTB000$DASA000*;MATT3AEEDTTB000$$DASA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HTR | FRICTION LINING |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL6061 | ALUMINUM ALLOY 6061 |
| ASA000 | ASBESTOS |
| ASB000 | ASBESTOS CHRYSOTILE |
| CSA000 | CELLULOSE |
| CLD000 | CERAMIC |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0103 | COPPER ALLOY 510 |
| CU0104 | COPPER ALLOY 511 |
| CU0670 | COPPER ALLOY 670 |
| CU0219 | COPPER ALLOY 954 |
| CKA000 | CORK |
| CCA000 | COTTON |
| LBF000 | DISULFIDE MOLYBDENUM |
| FBA000 | FIBER |
| FBAF00 | FIBER - ASBESTOS FREE |
| FEA000 | IRON |
| FEE000 | IRON RUST RESISTING |
| LRA000 | LEATHER |
| PPA000 | PAPER |
| PCA000 | PLASTIC |
| PCCX00 | PLASTIC ARAMID |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCQ000 | PLASTIC POLYCAPROLACTAM |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE |
| PCZ000 | PLASTIC POLYHEXAMETHYLENE ADIPAMIDE |
| RCE000 | RUBBER |
| RC0007 | RUBBER CHLOROPRENE CLASS CR |
| RCC000 | RUBBER SILICONE |
| RCB000 | RUBBER SYNTHETIC |
| STA000 | STEEL |
| TTB000 | TITANIUM |
| WLA000 | WOOL |
AARN*DFABRICATION METHOD
THE PROCESS USED IN MANUFACTURING THE ITEM.
Enter the applicable reply code from the table below
(AARNDAM*;AARNDAC$DDW*;AARNDAC$$DDW*)
| Table 1 |
| Reply Code (AA62) | Reply |
| A | ANY ACCEPTABLE |
| AC | COMPRESSED |
| DW | FOLDED |
| AM | MOLDED |
| AW | WOVEN |
IF STYLE/REPLY CODE(s) 1 OR 6 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AJKW and AJKY and ABNM and ABGL)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AJKW and ABMC and AJKY and ABMB and ABGL)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AJKW and AJKU and AJKT and AJKY and AJKS and AJAQ and ABNM and ABGL)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AAZR and AGJR and ABNM)
IF STYLE/REPLY CODE(s) 7 OR 8 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AAZR and AGJR and ABNM and AJLA)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AAZR and AGJR and ABNM and ABGL)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AJKW and AJKY and ABGG and ABNM and ABGL)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (ABHP and ABGL and ABNM)
IF STYLE/REPLY CODE(s) 12 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (ABHP and ABGL and ABMB and ABMC)
IF STYLE/REPLY CODE(s) 13 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (ABHP and ABNH and ALHX and ABNM)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (ABGL and AJKS and ABHP and ABNM)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (AAZR and ABNM)
IF STYLE/REPLY CODE(s) 16 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (ABGL and ABNM)
IF STYLE/REPLY CODE(s) 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27 OR 28 WERE ENTERED FOR MRC AJKK, YOU MUST ANSWER MRC (ALHX and ABHP and ABMC)
AJKKLLINING STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE LINING.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AJKKL1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DQ00973 | 1 | SEGMENT PLAIN |
| DQ00981 | 10 | CONE DISK SEGMENT |
| DQ00982 | 11 | RECTANGULAR BLOCK PLAIN |
| DQ00983 | 12 | RECTANGULAR BLOCK TAPERED |
| DQ00984 | 13 | TRAPEZOID BLOCK |
| DQ00985 | 14 | RENIFORM BLOCK |
| DQ00986 | 15 | PLAIN DISK |
| DQ00987 | 16 | BULK LINING |
| DQ00988 | 17 | DISK BRAKE SHOE W/RIVET LINING |
| DQ00989 | 18 | DISK BRAKE SHOE W/CEMENT BOND LINING |
| DQ00990 | 19 | DISK BRAKE SHOE |
| DQ00974 | 2 | SEGMENT TAPERED |
| DQ00991 | 20 | DISK BRAKE SHOE |
| DQ00992 | 21 | DISK BRAKE SHOE |
| DQ00993 | 22 | DISK BRAKE SHOE |
| DQ00994 | 23 | DISK BRAKE SHOE |
| DQ00995 | 24 | DISK BRAKE SHOE |
| DQ00996 | 25 | DISK BRAKE SHOE |
| DQ00997 | 26 | DISK BRAKE SHOE |
| DQ00998 | 27 | DISK BRAKE SHOE |
| DQ00999 | 28 | DISK BRAKE SHOE |
| DQ01000 | 29 | IRREGULAR |
| DQ00975 | 4 | SEGMENT LUGGED |
| DQ00976 | 5 | CLUTCH DISK |
| DQ00977 | 6 | CLUTCH DISK SEGMENT |
| DQ00978 | 7 | EXTERNAL TOOTH CLUTCH DISK |
| DQ00979 | 8 | INTERNAL TOOTH CLUTCH DISK |
| DQ00980 | 9 | CONE DISK |
AAZR*JMAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST DIAMETER OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAZRJAC2.0*;AAZRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGG*JRADIUS
THE DISTANCE FROM THE CENTERLINE TO THE AXIS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGGJAB2.0*;ABGGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAC2.0*;ABGLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMB*JMINOR THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMBJAA2.0*;ABMBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMC*JMAJOR THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMCJAA2.0*;ABMCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNH*JMINOR WIDTH
THE SMALLEST MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNHJAA2.0*;ABNHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJAA2.0*;ABNMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGJR*JMINOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST DIAMETER OF THE ITEM,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGJRJAC2.0*;AGJRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAQ*JLUG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAQJAC2.0*;AJAQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJKS*JARC LENGTH BETWEEN LUG CENTERS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJKSJAB2.0*;AJKSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJKT*JLUG DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJKTJAA2.0*;AJKTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJKU*JLUG CENTER TO LINING END DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJKUJAB2.0*;AJKUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJKW*JARC LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJKWJAC2.0*;AJKWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJKY*JMINOR RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJKYJAA2.0*;AJKYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALHX*JMAJOR WIDTH
THE LARGEST MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALHXJAA2.0*;ALHXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJLA*ATEETH QUANTITY
THE NUMBER OF TEETH INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJLAA10*)
IF STYLE/REPLY CODE(s) AAZ OR ABB WERE ENTERED FOR MRC CTPJ, YOU MUST ANSWER MRC (ABRB)
CTPJ*DATTACHMENT METHOD
THE MEANS BY WHICH THE ITEM IS ATTACHED.
Enter the applicable reply code from the table below
(CTPJDABB)
| Table 1 |
| Reply Code (AP50) | Reply |
| AAZ | BOLTED |
| ABA | BONDED |
| ABB | RIVETED |
IF STYLE/REPLY CODE(s) B1, B3, B4, B7, B8 OR B21 WERE ENTERED FOR MRC ABRB, YOU MUST ANSWER MRC (ADAZ and ABTB and ALHY and CTCX)
IF STYLE/REPLY CODE(s) B2, B5, B9, B10, B11, B12, B13, B14, B16, B17, B18, B19 OR B1A WERE ENTERED FOR MRC ABRB, YOU MUST ANSWER MRC (ABTB and ALHY and CTCX)
IF STYLE/REPLY CODE(s) C1, C2, C3, C4, C5, C7, C8, C9, C10 OR C11 WERE ENTERED FOR MRC ABRB, YOU MUST ANSWER MRC (ABTB and ALET)
IF STYLE/REPLY CODE(s) C12 WERE ENTERED FOR MRC ABRB, YOU MUST ANSWER MRC (ABGC and ABGD and ALET)
IF STYLE/REPLY CODE(s) C13 WERE ENTERED FOR MRC ABRB, YOU MUST ANSWER MRC (ABRC and ABRD and ALET)
ABRB*LHOLE ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE HOLES.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABRBLC10)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DQ01001 | B1 | INDEFINITE |
| DQ01010 | B10 | STAGGERED |
| DQ01011 | B11 | STAGGERED |
| DQ01012 | B12 | STAGGERED |
| DQ01013 | B13 | STAGGERED |
| DQ01014 | B14 | STAGGERED |
| DQ01016 | B16 | STAGGERED |
| DQ01017 | B17 | STAGGERED |
| DQ01018 | B18 | STRAIGHT |
| DQ01019 | B19 | DOUBLE EVEN |
| DQ01002 | B1A | INDEFINITE (NOTE: FOR DEFINITE DRILLING PATTERNS WITH MOUNTING HOLES ONLY) |
| DQ01003 | B2 | STRAIGHT |
| DQ01020 | B21 | STAGGERED |
| DQ01004 | B3 | ALTERNATE STRAIGHT |
| DQ01005 | B4 | ALTERNATE STRAIGHT |
| DQ01006 | B5 | DOUBLE EVEN |
| DQ01007 | B7 | DOUBLE EVEN |
| DQ01008 | B8 | DOUBLE EVEN |
| DQ01009 | B9 | STAGGERED |
| DQ01021 | C1 | INDEFINITE |
| DQ01029 | C10 | TRIPLE EVEN |
| DQ01030 | C11 | DOUBLE STAGGERED |
| DQ01031 | C12 | DOUBLE SLOTTED |
| DQ01032 | C13 | TWO DIFFERENT SIZES |
| DQ01022 | C2 | SINGLE |
| DQ01023 | C3 | STAGGERED |
| DQ01024 | C4 | DOUBLE EVEN |
| DQ01025 | C5 | DOUBLE STAGGERED |
| DQ01026 | C7 | DOUBLE EVEN |
| DQ01027 | C8 | STAGGERED |
| DQ01028 | C9 | STAGGERED |
ABGC*JSLOT WIDTH
THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGCJAB2.0*;ABGCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGD*JSLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGDJAC2.0*;ABGDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRC*JFIRST HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRCJAC2.0*;ABRCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRD*JSECOND HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRDJAA2.0*;ABRDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTBJAA2.0*;ABTBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAZ*JTHRU-HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A THRU-HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAZJAB2.0*;ADAZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALHY*JMOUNTING HOLE CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALHYJAC2.0*;ALHYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALET*JHOLE TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF HOLES PROVIDED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(ALETJAT2*;ALETJAT2$$JAT3*)
| Table 1 |
| Reply Code (AH37) | Reply |
| AB | COUNTERBORED |
| AC | COUNTERSUNK |
| AT | SLOT |
| AD | THRU-HOLE |
CTCX*JCIRCULAR PATTERN HOLE TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF HOLES PROVIDED ON THE CIRCULAR PATTERN.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(CTCX3AEEJAB2*;CTCX3AEEJAB2$$JAB3*;CTCX3AEEJAB2$JAB2*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CJR | SINGLE SECURING CIRCLE |
| 3CJS | OUTER SECURING CIRCLE |
| 3CJT | INNER SECURING CIRCLE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH37) | Reply |
| AB | COUNTERBORED |
| AC | COUNTERSUNK |
| AT | SLOT |
| AD | THRU-HOLE |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
ADZK*DSTRENGTHENING FEATURE
AN INTEGRAL FEATURE OF THE ITEM WHICH STRENGTHENS AND/OR STIFFENS THE BASIC MATERIAL.
Enter the applicable reply code from the table below
(ADZKDAD*;ADZKDBZ$DAC*;ADZKDBZ$$DAC*)
| Table 1 |
| Reply Code (AC71) | Reply |
| AC | INTERNALLY MOLDED-IN REINFORCEMENT |
| AD | INTERWOVEN WIRE |
| BZ | LAYERED FLAT STEEL BACKING MEMBER |
AJMJ*DAPPLICATION TYPE
INDICATES THE TYPE OF APPLICATION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(AJMJDAD*;AJMJDAB$$DAD*)
| Table 1 |
| Reply Code (AF75) | Reply |
| AB | DRY |
| AD | OIL |
CQHT*HSURFACE CONDITION AND LOCATION
THE CONDITION OF THE ITEM WITH RESPECT TO THE TEXTURE OF THE SURFACE AND ITS LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CQHTHBSDAT2.0*;CQHTHBSDAT2.0$$HBSDAT2.1*)
| Table 1 |
| Reply Code (AN73) | Reply |
| BSD | BOTH SIDES |
| WSE | ONE SIDE |
| SYD | SIDE |
| Table 2 |
| Reply Code (AN72) | Reply |
| GD | GROOVED |
| GR | GROUND |
| AT | UNGROUND |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBML*;CBBLDBMJ$$DBMG*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BMG | FLEXIBLE FRICTION LINING |
| BMH | FRICTION LINING |
| BMJ | INNER SHOE |
| BMK | OUTER SHOE |
| BML | RIGID FRICTION LINING |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AJAF*JUNPACKAGED UNIT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAFJLB2.0*;AJAFJLB2.0$$JLB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAA2.0*;AJAGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAB2.0*;AJAHJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAN)
| Table 1 |
| Reply Code (AM81) | Reply |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AJ | UNHEATED WAREHOUSE |
| AK | UNIMPROVED OPEN |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAE)
| Table 1 |
| Reply Code (AM83) | Reply |
| AE | FRAGILE |
| AK | MAGNETIC |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDC)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ALME*JMATERIAL HARDNESS RATING
A NUMERIC VALUE THAT REFLECTS THE HARDNESS OF THE MATERIAL WHEN USED IN CONJUNCTION WITH A HARDNESS RATING SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALMEJGCB2.0*;ALMEJGCB2.0$$JGCB2.1*)
| Table 1 |
| Reply Code (AC26) | Reply |
| GA | GOGAN A |
| GB | GOGAN B |
| GC | GOGAN C |
| GD | GOGAN D |
| SX | ROCKWELL SUPERFICIAL 15X |
| SY | ROCKWELL SUPERFICIAL 15Y |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ042)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HTR | FRICTION LINING |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information