An electrical device in the form of a resistor consisting of a resistance wire, an insulating material, and a sheath. It is designed to transform electrical current into heat while immersed in a liquid to be heated or in contact with materials to be melted. It may include an automatic control to regulate the amount of heat generated.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED11327*)
IF STYLE/REPLY CODE(s) 1 OR 3 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABJV and ABHP and ABRY and ABGL)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABJV and ABHP)
IF STYLE/REPLY CODE(s) 18, 20, 59, 60, 62 OR 66 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABGL)
IF STYLE/REPLY CODE(s) 4, 7, 23 OR 48 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABKV)
IF STYLE/REPLY CODE(s) 5, 21 OR 71 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKV)
IF STYLE/REPLY CODE(s) 6 OR 49 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKV and ABRY)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHU)
IF STYLE/REPLY CODE(s) 9, 14, 17, 26, 51, 52, 53, 55, 56, 57, 58, 63, 64, 65 OR 68 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHY and ABHU)
IF STYLE/REPLY CODE(s) 11, 12, 50 OR 73 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABRY)
IF STYLE/REPLY CODE(s) 13, 75, 78 OR 79 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABGL and ABRY)
IF STYLE/REPLY CODE(s) 24 OR 25 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (AARX and ABGL)
IF STYLE/REPLY CODE(s) 61 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABNT)
IF STYLE/REPLY CODE(s) 54 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABHT and ABKV)
IF STYLE/REPLY CODE(s) 70 OR 72 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (CRXP and CSGY)
IF STYLE/REPLY CODE(s) 30, 32, 40, 47, 67 OR 76 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABKV)
IF STYLE/REPLY CODE(s) 38 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABKV)
IF STYLE/REPLY CODE(s) 31 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY)
IF STYLE/REPLY CODE(s) 41 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABRY)
IF STYLE/REPLY CODE(s) 27 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABNT)
IF STYLE/REPLY CODE(s) 28, 29 OR 45 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABNT)
IF STYLE/REPLY CODE(s) 33 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABRY and ABHT and ABNT)
IF STYLE/REPLY CODE(s) 34 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHT and ABNT and ABHU)
IF STYLE/REPLY CODE(s) 35 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABRY and ABHV and ABNT and ABHU)
IF STYLE/REPLY CODE(s) 36 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHV and ABNT and CSGY and CRXP)
IF STYLE/REPLY CODE(s) 37 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHP and ABRY and ABGL and ABNT)
IF STYLE/REPLY CODE(s) 39 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABRY and ABGL and ABNT)
IF STYLE/REPLY CODE(s) 43 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHU and ABHY and ABNT)
IF STYLE/REPLY CODE(s) 69 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ABHV)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAT1001 | 1 | STRIP ELEMENT |
| DQ00086 | 10 | TUBULAR, HELICAL COILED |
| DQ00087 | 11 | TUBULAR, SCREW PLUG TYPE |
| DQ00088 | 12 | TUBULAR, SINGLE COIL DOUBLE TERMINALS |
| DQ00089 | 13 | TUBULAR, M SHAPED |
| DQ00090 | 14 | TUBULAR, U SHAPED |
| AAT1008 | 17 | TUBULAR, DOUBLE LOOP |
| AAT1009 | 18 | OVEN TYPE |
| AAT1002 | 2 | STRIP, WEDGE |
| AAT1010 | 20 | TUBULAR, RECTANGULAR |
| AAT1011 | 21 | COIL, PLAIN |
| AAT1012 | 23 | CARTRIDGE, SCREW BASE |
| AAT1013 | 24 | CIRCULAR, FINNED |
| AAT1014 | 25 | BAND TYPE/NOZZLE ELEMENT |
| AAT1015 | 26 | FINNED, TUBULAR, U SHAPED |
| AAT1016 | 27 | SCREW TYPE |
| AAT1017 | 28 | PLUG TYPE |
| AAT1018 | 29 | FLANGE TYPE |
| AAT1003 | 3 | STRIP, FINNED |
| AAT1019 | 30 | CARTRIDGE, SCREW TYPE |
| AAT1020 | 31 | TUBULAR, SCREW TYPE |
| AAT1021 | 32 | CARTRIDGE, PLUG TYPE |
| AAT1022 | 33 | DEEP TANK, STRAIGHT BLADES |
| AAT1023 | 34 | DEEP TANK, CIRCULAR BLADE, OVER-THE-SIDETYPE |
| AAT1024 | 35 | TUBULAR OVER-THE-SIDE TYPE |
| AAT1025 | 36 | TUBULAR OVER-THE-SIDE TYPE |
| AAT1026 | 37 | FLAT, THRU-THE-SIDE |
| AAT1027 | 38 | CIRCULAR TANK TYPE |
| AAT1028 | 39 | BOTTOM CLAMPING |
| AAT1004 | 4 | FINNED, TUBULAR, TERMINAL'S AT EACH END |
| AAT1029 | 40 | CARTRIDGE, OVER-THE-SIDE TYPE |
| AAT1030 | 41 | TUBULAR THRU-THE-SIDE TYPE |
| AAT1031 | 43 | TUBULAR, VERTICAL TYPE |
| AAT1032 | 45 | FLANGE, TYPE |
| AAT1033 | 47 | CARTRIDGE TYPE |
| AAT1034 | 48 | TUBULAR, THREADED |
| AAT1035 | 49 | TUBE ELEMENT, DOUBLE TERMINALS |
| AAT1005 | 5 | SINGLE HEAT RING |
| AAT1036 | 50 | TUBE, DOUBLE TERMINALS |
| AAT1037 | 51 | TUBULAR, DOUBLE TERMINALS |
| AAT1038 | 52 | TUBULAR, SHEATHED, THREADED TERMINALS |
| AAT1039 | 53 | TUBULAR, FLANGED, W/TERMINALS |
| AAT1040 | 54 | TUBULAR, SHEATHED, THREADED END |
| AAT1041 | 55 | TUBULAR, THREADED TERMINALS |
| AAT1042 | 56 | TUBULAR, DOUBLE TERMINALS |
| AAT1043 | 57 | TUBULAR, FLANGED, W/O TERMINALS |
| AAT1044 | 58 | TUBULAR, FLANGED, PLAIN |
| AAT1045 | 59 | TUBULAR, "L" SHAPED W/TERMINALS |
| AAT1006 | 6 | TUBULAR, PLAIN |
| AAT1046 | 60 | TUBULAR, FLANGED |
| AAT1047 | 61 | TUBULAR, SINGLE TERMINAL |
| AAT1048 | 62 | TUBULAR, DOUBLE TERMINALS |
| AAT1049 | 63 | TUBULAR, FLANGED |
| AAT1050 | 64 | TUBULAR, FLANGED |
| AAT1051 | 65 | TUBULAR, FLANGED |
| AAT1052 | 66 | PLUG TYPE, FLANGED |
| AAT1053 | 67 | OVER-THE-SIDE TYPE |
| AAT1054 | 68 | CARTRIDGE TYPE, W/HANDLE |
| AAT1055 | 69 | THRU-THE-SIDE TYPE |
| AAT1007 | 7 | TUBULAR, STEPPED |
| AAT1056 | 70 | TUBULAR, FLANGED |
| AAT1057 | 71 | CIRCULAR, TUBULAR, W/TERMINALS |
| AAT1058 | 72 | TUBULAR, CARTRIDGE TYPE TERMINAL |
| AAT1059 | 73 | TUBULAR, W/O TERMINALS |
| AAT1060 | 75 | CABLE MAT |
| AAT1061 | 76 | OVER-THE-SIDE TYPE |
| AAT1062 | 77 | CABLE, BAND OR TAPE TYPE |
| AAT1063 | 78 | STANDARD ELEMENT |
| AAT1064 | 79 | STANDARD ELEMENT |
| DQ00084 | 8 | TUBULAR, SINGLE COIL, DOUBLE TERMINALS |
| AAT1065 | 80 | ODD/IRREGULAR SHAPED ITEMS |
| DQ00085 | 9 | TUBULAR, DOUBLE COIL, DOUBLE TERMINALS |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAC2.0*;AARXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGL*JWIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGLJAC2.0*;ABGLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHT*JRISER HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHTJAB2.0*;ABHTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHU*JMINIMUM CLEARANCE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHUJAA2.0*;ABHUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHV*JDISTANCE FROM TERMINAL BOX
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHVJAB2.0*;ABHVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHY*ATURN QUANTITY
THE NUMBER OF TURNS OF CONDUCTIVE MATERIAL FORMING THE WINDING.
Enter the alpha-numeric reply with a minimum of one character.
(ABHYAT4)
ABKV*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKVJAA2.0*;ABKVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNT*JCONDUIT OPENING SIZE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNTJAA2.0*;ABNTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABRY*JLENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF ANY OBJECT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRYJAC2.0*;ABRYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRXP*JHORIZONTAL LEG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRXPJAC2.0*;CRXPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSGY*JVERTICAL LEG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSGYJAA2.0*;CSGYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABJV*LTERMINAL ARRANGEMENT STYLE
A NUMERIC DESIGNATION APPLIED TO THE LOCATION OF THE ELECTRICAL TERMINALS.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABJVL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAT1085 | 1 | ONE AT EACH END |
| AAT1086 | 2 | OFFSET OR STAGGERED AT ONE END |
| AAT1087 | 3 | PARALLEL AT ONE END EXCEPT ON 3/4 AND 1 INCH WIDTH |
| AAT1088 | 4 | THREE AT ONE END - FOR THREE HEAT |
| AAT1089 | 5 | IN LINE (TANDEM) AT ONE END |
| AAT1090 | 6 | PARALLEL AT CENTER |
| AAT1091 | 7 | IN LINE (TANDEM) AT CENTER |
ABJADELEMENT RADIATION SPECTRUM
AN INDICATION OF THE RADIATION SPECTRUM OF THE ELEMENT.
Enter the applicable reply code from the table below
(ABJADA)
| Table 1 |
| Reply Code (AB35) | Reply |
| B | FAR INFRARED |
| A | NEAR INFRARED |
| C | NONINFRARED |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3ATEDST0347*;MATT3ATEDST0347$DNL0002*;MATT3ATEDST0347$$DNL0002*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATE | RESISTANCE WIRE |
| 3ATF | RESISTANCE WIRE EMBEDDING/SUPPORT INSULATION |
| 3ATG | SHEATH |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL6061 | ALUMINUM ALLOY 6061 |
| ASA000 | ASBESTOS |
| CLC000 | BRICK |
| CAA000 | CALCIUM SILICATE |
| CXA000 | CEMENT |
| CLD000 | CERAMIC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CCA000 | COTTON |
| WDA000 | FIBERBOARD |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| GSC000 | GLASS SODA-LIME |
| FEA000 | IRON |
| FEE000 | IRON RUST RESISTING |
| LVA000 | LAVA |
| PBA000 | LEAD |
| MGA000 | MAGNESIUM |
| MGC000 | MAGNESIUM OXIDE |
| MNA000 | MANGANESE |
| MNB000 | MANGANESE ALLOY |
| AYA000 | MICA |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| NL0059 | NICKEL ALLOY 800 |
| NL0001 | NICKEL ALLOY A |
| NL0002 | NICKEL ALLOY B |
| NL0014 | NICKEL ALLOY C |
| NL0011 | NICKEL ALLOY D |
| NL0013 | NICKEL ALLOY E |
| NLC000 | NICKEL SILVER |
| FBB000 | NYLON (USE PCP000) |
| PCA000 | PLASTIC |
| PCH000 | PLASTIC EPOXY |
| PCM000 | PLASTIC PHENOL FORMALDEHYDE (PMO) |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCW000 | PLASTIC POLYESTER |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAR00 | PLASTIC POLYTRIFLUOROETHYLENE |
| PCAS00 | PLASTIC POLYVINYLIDENE FLUORIDE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PTA000 | PLATINUM |
| CLB000 | PORCELAIN |
| SLG000 | QUARTZ |
| RSC000 | RESIN NATURAL |
| RSA000 | RESIN SYNTHETIC |
| RHA000 | RHODIUM |
| RCA000 | RUBBER NATURAL |
| RCB000 | RUBBER SYNTHETIC |
| SLB000 | SILICON CARBIDE |
| STA000 | STEEL |
| ST0302 | STEEL COMP 302 |
| ST0304 | STEEL COMP 304 |
| ST0080 | STEEL COMP 304L |
| ST0316 | STEEL COMP 316 |
| ST0082 | STEEL COMP 316L |
| ST0317 | STEEL COMP 317 |
| ST0321 | STEEL COMP 321 |
| ST0347 | STEEL COMP 347 |
| ST0410 | STEEL COMP 410 |
| ST0430 | STEEL COMP 430 |
| STB000 | STEEL CORROSION RESISTING |
| TTC000 | TITANIA |
| TTB000 | TITANIUM |
| WXA000 | WAX |
| ZRA000 | ZIRCONIUM SILICATE |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATE | RESISTANCE WIRE |
| 3ATF | RESISTANCE WIRE EMBEDDING/SUPPORT INSULATION |
| 3ATG | SHEATH |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC CSBH, YOU MUST ANSWER MRC (FREQ and FAAZ)
CSBHJVOLTAGE IN VOLTS AND CURRENT TYPE
THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHETHER ALTERNATING OR DIRECT.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBH3ATKJAC2.0*;CSBH3ATKJAC2.0$JAC2.0*;CSBH3ATKJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATH | FIRST VOLTAGE |
| 3ATI | SECOND VOLTAGE |
| 3ATJ | THIRD VOLTAGE |
| 3ATK | SINGLE VOLTAGE |
| 3ATL | ALL VOLTAGES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN87) | Reply |
| AC | AC |
| DC | DC |
| AA | VOLTAGE DIRECT CURRENT |
FREQ*BFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(FREQB2.0*;FREQB2.0$$BM2.0*)
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(FAAZ3AEEDC*;FAAZ3AEEDC$DB*;FAAZ3AEEDC$$DB*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATH | FIRST VOLTAGE |
| 3ATI | SECOND VOLTAGE |
| 3ATJ | THIRD VOLTAGE |
| 3ATK | SINGLE VOLTAGE |
| 3ATL | ALL VOLTAGES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| C | THREE |
| B | TWO |
AZQHBMAXIMUM WATTAGE RATING IN WATTS
THE MAXIMUM RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(AZQH3ATJB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATH | FIRST VOLTAGE |
| 3ATI | SECOND VOLTAGE |
| 3ATJ | THIRD VOLTAGE |
| 3ATK | SINGLE VOLTAGE |
| 3ATL | ALL VOLTAGES |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
ABNSJWATT DENSITY RATING
THE HEAT OUTPUT OF THE HEATED PORTION OF THE SURFACE AREA OF THE HEATING ELEMENT.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNS1XJH2.0*;ABNS1XJH2.0$JH2.1*)
| Table 1 |
| ISAC Field Indicator (0085) | Location |
| 1A | 1ST VOLTAGE |
| 1B | 2ND VOLTAGE |
| 1C | 3RD VOLTAGE |
| 1X | SINGLE VOLTAGE |
| 1Z | ALL VOLTAGES |
| Table 2 |
| Reply Code (AB39) | Reply |
| A | PER SQUARE INCH |
| H | PER SQUARE MILLIMETER |
IF STYLE/REPLY CODE(s) E WERE ENTERED FOR MRC ABJM, YOU MUST ANSWER MRC (ABJN)
ABJM*DHEAT CONTROL TYPE
INDICATES THE TYPE OF HEAT CONTROL INCLUDED ON THE ITEM.
Enter the applicable reply code from the table below
(ABJMDC)
| Table 1 |
| Reply Code (AB37) | Reply |
| F | HEAT SWITCH |
| C | THERMAL CUTOUT SWITCH |
| D | THERMOCOUPLE |
| E | THERMOSTAT |
ABJN*JTHERMOSTAT RANGE
THE MINIMUM AND MAXIMUM TEMPERATURE RATINGS THROUGH WHICH THE THERMOSTAT WILL OPERATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ABJNJFM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BHHKAELEMENT QUANTITY
THE NUMBER OF ELEMENTS IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(BHHKA10*)
ABNRAHEAT QUANTITY
THE NUMBER OF HEATS AT WHICH THE ITEM WILL OPERATE.
Enter the numeric reply with a minimum of one digit.
(ABNRA10*)
IF STYLE/REPLY CODE(s) 1, 4, 5, 8, 9, 10, 11 OR 12 WERE ENTERED FOR MRC ABJS, YOU MUST ANSWER MRC (AARA and ABJT)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC ABJS, YOU MUST ANSWER MRC (AARA and ABJT and ABJU)
IF STYLE/REPLY CODE(s) 3, 6, 7 OR 18 WERE ENTERED FOR MRC ABJS, YOU MUST ANSWER MRC (AARA)
ABJSLELEMENT CONNECTION STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ELEMENT CONNECTION.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ABJSL18)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAT1066 | 1 | WIRE LEAD |
| AAT1075 | 10 | WIRE LEAD W/ROUND BAYONET |
| AAT1076 | 11 | ROUND BAYONET |
| AAT1077 | 12 | WIRE LEAD W/TERMINAL LUG |
| AAT1078 | 13 | MEDIUM CANDELABRA |
| AAT1079 | 14 | MEDIUM SCREW |
| AAT1080 | 15 | MEDIUM SCREW SKIRTED |
| AAT1081 | 16 | MEDIUM PREFOCUS |
| AAT1082 | 17 | MEDIUM BIPOST |
| AAT1083 | 18 | EYELET |
| AAT1084 | 19 | ODD/IRREGULAR SHAPED ITEMS |
| AAT1067 | 2 | SHIELDED WIRE LEAD |
| AAT1068 | 3 | TERMINAL SCREW |
| AAT1069 | 4 | STUD TYPE |
| AAT1070 | 5 | HERMETICALLY SEALED STUD |
| AAT1071 | 6 | CONNECTOR RECEPTACLE |
| AAT1072 | 7 | CONNECTOR PLUG |
| AAT1073 | 8 | FLAT BAYONET |
| AAT1074 | 9 | TERMINAL LUG |
AARA*ATERMINAL QUANTITY
THE NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AARAA10*)
ABJT*JTERMINAL LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A TERMINAL,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJTJAA2.0*;ABJTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABJU*JSHIELDING LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABJUJAC2.0*;ABJUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQKC*JPOWER CABLE NOMINAL LENGTH
A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE POWER CABLE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQKCJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQLD*JFLEXIBLE TUBE NOMINAL LENGTH
A NOMINAL MEASUREMENT OF THE LONGEST DIMENSION OF THE FLEXIBLE TUBE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQLDJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ABHS*JEFFECTIVE HEATING LENGTH
THE LENGTH OF THAT PORTION OF THE HEATING ELEMENT THAT IMPARTS HEAT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHSJAB2.0*;ABHSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKF*DTERMINAL BOX ENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS WHICH A TERMINAL BOX IS DESIGNED TO WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ABKFDD*;ABKFDB$$DC*)
| Table 1 |
| Reply Code (AB38) | Reply |
| B | EXPLOSION RESISTANT |
| C | MOISTURE RESISTANT |
| D | STANDARD |
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC AALX, YOU MUST ANSWER MRC (AAUB and ABKS and ABKP) or (AAUB and ABKS and ABKP and ABKT) or (AAUB and ABKS and ABKN) or (ABKM)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC AALX, YOU MUST ANSWER MRC (ABKS and ABKP and ABKQ and ABKT and ABKR) or (ABKP and ABKS and ABKT) or (ABKR and AAUB and ABKT)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC AALX, YOU MUST ANSWER MRC (ABKK and ABKT and AAUB and ABKG and ABKU) or (AAUB and ABKT and ABKR and ABKQ and ABKU and ABKS and ABKP) or (AAUB and ABKS and ABKQ and ABKP and ABKU and ABKT)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC AALX, YOU MUST ANSWER MRC (AAUB and ABKS and ABKP) or (AAUB and ABKT and ABKS and ABKN)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC AALX, YOU MUST ANSWER MRC (ABKJ)
IF STYLE/REPLY CODE(s) 9, 10, 11 OR 12 WERE ENTERED FOR MRC AALX, YOU MUST ANSWER MRC (ABKP)
AALX*LMOUNTING METHOD STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE MOUNTING METHOD OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AALXL2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAT1092 | 1 | TERMINAL MOUNTED |
| AAT1101 | 10 | STUD TYPE MOUNTING FACILITY |
| AAT1102 | 11 | STANDOFF TYPE MOUNTING FACILITY |
| AAT1103 | 12 | AXIAL STUD TYPE MOUNTING FACILITY |
| AAT1093 | 2 | CLAMP TYPE MOUNTING FACILITY |
| AAT1094 | 3 | SLOT OR HOLE TYPE MOUNTING FACILITY |
| AAT1095 | 4 | FLANGE TYPE MOUNTING FACILITY |
| AAT1096 | 5 | BRACKET TYPE MOUNTING FACILITY |
| AAT1097 | 6 | FRICTION TYPE MOUNTING FACILITY |
| AAT1098 | 7 | WRAP AROUND TYPE MOUNTING FACILITY |
| AAT1099 | 8 | PIPE THREAD TYPE MOUNTING FACILITY |
| AAT1100 | 9 | SCREW PLUG OR BUSHING TYPE MOUNTING FACILITY |
AAUB*JHOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUBJAB2.0*;AAUBJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAB2.0*;ABKGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKJ*JCASE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CASE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKJJAA2.0*;ABKJJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKK*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKKJAA2.0*;ABKKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKM*JCLAMP INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKMJAB2.0*;ABKMJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKN*JMOUNTING FACILITY HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKNJAA2.0*;ABKNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKP*JMOUNTING FACILITY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING FACILITY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKPJAB2.0*;ABKPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKQ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKQJAC2.0*;ABKQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO WIDTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKRJAC2.0*;ABKRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKS*JMOUNTING FACILITY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING FACILITY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKSJAA2.0*;ABKSJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKT*AHOLE OR SLOT QUANTITY
THE NUMBER OF HOLES OR SLOTS INCLUDED.
Enter the numeric reply with a minimum of one digit.
(ABKTA10*)
ABKU*JFLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKUJAC2.0*;ABKUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) NC, NE, NF, NP, PM, SP OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CQRN)
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(THSD3ATMDNF*;THSD3ATMDNF$DPM*;THSD3ATMDNF$$DPM*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AHZ | MOUNTING FACILITY |
| 3ATM | SCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH06) | Reply |
| BV | BRITISH STANDARD PIPE (BSP) |
| SM | ISO M |
| SS | ISO S |
| SP | NPS |
| PM | NPSM |
| NP | NPT |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJX3AHZJA2.0*;CQJX3AHZJA2.0$JA2.0*;CQJX3AHZJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AHZ | MOUNTING FACILITY |
| 3ATM | SCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQRN*JTHREAD QUANTITY
THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CQRN3ADUJD2.0*;CQRN3ADUJD2.0$JD2.0*;CQRN3ADUJD2.0$$JD2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ADU | STUD |
| 3AEE | OVERALL |
| 3AHZ | MOUNTING FACILITY |
| 3ATM | SCREW |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AB39) | Reply |
| D | PER CENTIMETER |
| C | PER INCH |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAGX*;CBBLDAGT$$DAGS*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AGX | CAPILLARY TUBE WELL |
| AGR | DETACHABLE LEADS |
| AGS | MECHANICAL LOCK CONNECTION PLUG |
| AGT | OVERLOAD RELAY ELEMENT |
| AGW | WARMING ELEMENT |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AJAH*JUNPACKAGED UNIT HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAHJAC2.0*;AJAHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJAG*JUNPACKAGED UNIT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJAGJAB2.0*;AJAGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAM*;BBRGDAD$$DAE*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AC | CLOSED SHED |
| AD | CONTROLLED HUMIDITY WAREHOUSE |
| AM | DEHUMIDIFIED WAREHOUSE |
| AE | GENERAL PURPOSE WAREHOUSE |
| AN | HEATED WAREHOUSE |
| AH | OPEN SHED |
| AJ | UNHEATED WAREHOUSE |
BBRH*JINSPECTION FREQUENCY
THE SPECIFIED TIME INTERVAL,FROM RECEIPT,NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit.
(BBRHJMHAC2*;BBRHJMHAC2$$JMHAC3*;BBRHJMHAC2$JMHAC2*)
| Table 1 |
| Reply Code (AH68) | Reply |
| DY | DAYS |
| MH | MONTHS |
| Table 2 |
| Reply Code (AM82) | Reply |
| AB | FIRST INSPECTION |
| AC | REINSPECTION |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAS)
| Table 1 |
| Reply Code (AM83) | Reply |
| AS | CORROSIVE LIQUID |
| AD | FLAMMABLE |
| AK | MAGNETIC |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ029*;HZRDDHAZ042$$DHAZ012*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ012 | COPPER |
| HAZ029 | LEAD |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information