A cylinder, usually incorporating an integral reservoir, designed to house the necessary component parts of a CYLINDER ASSEMBLY, HYDRAULIC BRAKE, MASTER.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED10935*)
ABHPJOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXVJBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXV3AGRJAC2.0*;ABXV3AGRJAC2.0$JAC2.0*;ABXV3AGRJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BBJXDMOUNTING POSITION
THE INSTALLED POSITION FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable reply code from the table below
(BBJXDABX*;BBJXDABW$$DABW*)
| Table 1 |
| Reply Code (AM84) | Reply |
| ABW | LEFT |
| ABX | RIGHT |
AFLWDACTUATION METHOD
THE MEANS BY WHICH THE ITEM IS ACTUATED.
Enter the applicable reply code from the table below
(AFLWDAAGR)
| Table 1 |
| Reply Code (AC58) | Reply |
| AAGR | CAM |
| AAGQ | DIRECT |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAB2.0*;ADAVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAR*JBODY OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADARJAC2.0*;ADARJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYXG*JSTRAIGHT BORE INSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYXGJAB2.0*;BYXGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLML*HMOUNTING TYPE AND LOCATION
INDICATES THE TYPE OF MOUNTING AND THE LOCATION ON THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below.
(CLMLHBFADAA2.0*;CLMLHBFADAA2.0$HBFADAA2.0*;CLMLHBFADAA2.0$$HBFADAA2.1*)
| Table 1 |
| Reply Code (AM39) | Reply |
| BFA | BALL SOCKET |
| BNA | BALL STUD |
| BNB | BEARING |
| BXR | BORE |
| ADN | BOSS |
| ACR | FLANGE |
| BPL | FLAT |
| BKK | FORK |
| ABN | LUG |
| AHT | RING |
| ABT | ROD |
| ABW | SCREW |
| AAE | STUD |
| BKL | TONGUE |
| AKG | TRUNNION |
| Table 2 |
| Reply Code (AJ91) | Reply |
| AHH | BOTH ENDS |
| DAC | CENTER SECTION |
| EAT | CYLINDER BASE |
| DAA | CYLINDER HEAD END |
| DAB | PISTON ROD END |
IF STYLE/REPLY CODE(s) EE WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (CLMQ and ABKP)
IF STYLE/REPLY CODE(s) EF WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and ABGC and ABGD)
IF STYLE/REPLY CODE(s) AL WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and CDTD)
IF STYLE/REPLY CODE(s) AQ OR HP WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and CDTD and ABKP)
IF STYLE/REPLY CODE(s) AT WERE ENTERED FOR MRC ABDR, YOU MUST ANSWER MRC (BBBW and CLMQ)
ABDR*DMOUNTING PROVISION
THE PROVISION/S/ FOR MOUNTING THE ITEM. PLEASE USE MRC BHMS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ABDRDAL*;ABDRDHP$$DAQ*)
| Table 1 |
| Reply Code (AB21) | Reply |
| HN | LINK |
| GA | LUGS |
| EE | PIN |
| EF | SLOT |
| AL | THREADED MOUNTING HOLES |
| HP | THREADED MOUNTING SCREWS |
| AQ | THREADED MOUNTING STUDS |
| AT | UNTHREADED MOUNTING HOLES |
IF STYLE/REPLY CODE(s) 10, 11 OR 12 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (CLMR)
IF STYLE/REPLY CODE(s) 13, 14 OR 15 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AFDT and AFDS and AFDV)
IF STYLE/REPLY CODE(s) 16, 17, 18, 19, 20 OR 21 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AFDV and AFDS)
IF STYLE/REPLY CODE(s) 22, 23 OR 24 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AFDV and AFDW and AFDS)
IF STYLE/REPLY CODE(s) 25, 26, 27, 28, 29, 30, 31, 32 OR 33 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (AZCR)
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 5, 6, 7, 8 OR 9 WERE ENTERED FOR MRC BBBW, YOU MUST ANSWER MRC (CLMR)
BBBW*LMOUNTING PROVISION ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE MOUNTING PROVISION(S).
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(BBBWL3)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR00107 | 1 | TWO HOLE |
| DR00127 | 10 | FIVE HOLE |
| DR00128 | 11 | FIVE STUD |
| DR00129 | 12 | FIVE SLOT |
| DR00130 | 13 | THREE HOLE TRIANGULAR |
| DR00131 | 14 | THREE STUD TRIANGULAR |
| DR00132 | 15 | THREE SLOT TRIANGULAR |
| DR00133 | 16 | FOUR HOLE SQUARE |
| DR00134 | 17 | FOUR STUD SQUARE |
| DR00135 | 18 | FOUR SLOT SQUARE |
| DR00172 | 19 | FOUR HOLE RECTANGULAR |
| DR00108 | 2 | TWO STUD |
| DR00173 | 20 | FOUR STUD RECTANGULAR |
| DR00174 | 21 | FOUR SLOT RECTANGULAR |
| DR00196 | 22 | SIX HOLE RECTANGULAR |
| DR00197 | 23 | SIX STUD RECTANGULAR |
| DR00198 | 24 | SIX SLOT RECTANGULAR |
| DR00199 | 25 | THREE HOLE BOLT CIRCLE |
| DR00200 | 26 | THREE STUD BOLT CIRCLE |
| DR00201 | 27 | THREE SLOT BOLT CIRCLE |
| DR00207 | 28 | FOUR HOLE BOLT CIRCLE |
| DR00208 | 29 | FOUR STUD BOLT CIRCLE |
| DR00109 | 3 | TWO SLOT |
| DR00209 | 30 | FOUR SLOT BOLT CIRCLE |
| DR00210 | 31 | SIX HOLE BOLT CIRCLE |
| DR00211 | 32 | SIX STUD BOLT CIRCLE |
| DR00212 | 33 | SIX SLOT BOLT CIRCLE |
| DR00213 | 34 | SINGLE HOLE |
| DR00214 | 35 | SINGLE STUD |
| DR00215 | 36 | SINGLE SLOT |
| DR00112 | 4 | THREE HOLE |
| DR00117 | 5 | THREE STUD |
| DR00118 | 6 | THREE SLOT |
| DR00124 | 7 | FOUR HOLE |
| DR00125 | 8 | FOUR STUD |
| DR00126 | 9 | FOUR SLOT |
AFDS*JLONGEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDSJAC2.0*;AFDSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDT*JSHORTEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDTJAB2.0*;AFDTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDV*JLONGEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDVJAA2.0*;AFDVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDW*JSHORTEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDWJAA2.0*;AFDWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AZCR*JMOUNTING FACILITY CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING FACILITY CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AZCRJAB2.0*;AZCRJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLMR*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING PROVISIONS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMRJAA2.0*;CLMRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) NC, NE, NF, NJ, NS, JC, JE, JF OR UN WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CDTF and CDTG and AKBM and AKBN and CLMN)
IF STYLE/REPLY CODE(s) BF OR BW WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CDTF and AKBN and CLMN)
IF STYLE/REPLY CODE(s) BR, BS, NH, NP, NT, PE, PF, PM, PP, PS, PT, SC, SF, SH, SL, SP, AN OR FP WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (AKBN and CLMP)
IF STYLE/REPLY CODE(s) SJ, SK, SM OR SS WERE ENTERED FOR MRC CDTD, YOU MUST ANSWER MRC (CTXF and CDTF and AKBN and CLMN)
CDTD*DMOUNTING FACILITY THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE APPLIED TO A MOUNTING FACILITY DIAMETER.
Enter the applicable reply code from the table below
(CDTDDJC*;CDTDDFP$$DNS*)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| NS | UNS |
CDTF*JMOUNTING FACILITY THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACILITY WHICH WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CDTFJAA2.0*;CDTFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CDTG*AMOUNTING FACILITY THREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE MOUNTING FACILITY PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CDTGAK7)
CTXF*BMOUNTING FACILITY THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE MOUNTING FACILITY,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTXFB2.0)
AKBM*AMOUNTING FACILITY THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE,AND AN EXTERNAL OR INTERNAL THREADED MOUNTING FACILITY.
Enter the alpha-numeric reply with a minimum of one character.
(AKBMAV0)
AKBN*DMOUNTING FACILITY THREAD DIRECTION
THE DIRECTION OF THE THREADS OF A MOUNTING FACILITY WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AKBNDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CLMN*JMOUNTING FACILITY THREAD LENGTH
THE LENGTH OF THE THREADED PORTION OF THE MOUNTING FACILITY.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMNJAB2.0*;CLMNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLMP*JMOUNTING FACILITY NOMINAL PIPE THREAD SIZE
THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE MOUNTING FACILITY PIPE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMPJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CLMQ*JMOUNTING FACILITY DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE MOUNTING FACILITY,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMQJAA2.0*;CLMQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKP*JMOUNTING FACILITY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A MOUNTING FACILITY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKPJAC2.0*;ABKPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGC*JSLOT WIDTH
THE DISTANCE,MEASURED ALONG A STRAIGHT LINE PERPENDICULAR TO THE LONGITUDINAL AXIS OF THE SLOT,FROM ONE EDGE TO THE OTHER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGCJAA2.0*;ABGCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGD*JSLOT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SLOT,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGDJAA2.0*;ABGDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) DAA, DAB OR DAC WERE ENTERED FOR MRC CLMS, YOU MUST ANSWER MRC (CLMT)
CLMS*JPORT LOCATION AND QUANTITY
INDICATES THE LOCATION AND NUMBER OF PORTS ON THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(CLMSJDAB2*;CLMSJDAB2$$JDAB3*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| DAC | CENTER SECTION |
| EAT | CYLINDER BASE |
| DAA | CYLINDER HEAD END |
| DAB | PISTON ROD END |
IF STYLE/REPLY CODE(s) 12, 14, 15, 18, 20 OR 24 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (CLMW and AJFY)
IF STYLE/REPLY CODE(s) 13, 19, 21, 22, 23 OR 28 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (CLMW)
IF STYLE/REPLY CODE(s) 10, 11, 16, 17, 25, 26 OR 27 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (CLMW)
IF STYLE/REPLY CODE(s) 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42 OR 43 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (AARX)
IF STYLE/REPLY CODE(s) 44, 45, 46, 47, 48, 49, 50, 51, 52 OR 53 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (ABHE)
IF STYLE/REPLY CODE(s) 1, 2, 3, 4, 6, 7 OR 9 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (CLMW and AJFY)
IF STYLE/REPLY CODE(s) 8 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (CLMW)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC CLMT, YOU MUST ANSWER MRC (CLMW)
CLMT*LPORT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE PORT.
Enter the applicable ISAC from the table below folowed by the mode code and the applicable reply code from the drawing group below.
(CLMT3AEEL5*;CLMT3AEEL5$L12*;CLMT3AEEL5$$L12*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1762 | 1 | SWIVEL NUT, FLARE |
| AAQ1771 | 10 | SWIVEL NUT, GAS |
| AAQ1772 | 11 | DOUBLE COMPRESSION |
| AAQ1773 | 12 | HIGH PRESSURE FLARE |
| AAQ1774 | 13 | GASKET SEAL COMPRESSION |
| AAQ1775 | 14 | INVERTED FLARE |
| AAQ1776 | 15 | FLARED |
| AAQ1777 | 16 | FLARED |
| AAQ1778 | 17 | COMPRESSION |
| DQ00439 | 18 | FLARELESS |
| AAQ1780 | 19 | PLAIN |
| AAQ1763 | 2 | SWIVEL NUT, INVERTED FLARE |
| AAQ1781 | 20 | SWIVEL NUT INVERTED FLARE |
| AAQ1782 | 21 | SWIVEL, PLAIN |
| AAQ1783 | 22 | GASKET SEAL |
| AAQ1784 | 23 | EXTERNAL SEAT FOR GASKET SEAL |
| AAQ1785 | 24 | EXTERNAL SEAT FOR GASKET SEAL |
| AAQ1786 | 25 | EXTERNAL SEAT FOR GASKET SEAL |
| AAQ1787 | 26 | SWIVEL NUT, FLARED |
| AAQ1788 | 27 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAQ1789 | 28 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAQ1790 | 29 | SOCKET |
| AAQ1764 | 3 | SWIVEL NUT, FLARE |
| AAQ1791 | 30 | STREAMLINED WITH ONE BRAZING RING |
| AAQ1792 | 31 | STREAMLINE WITH TWO BRAZING RINGS |
| AAQ1793 | 32 | REDUCED SOCKET |
| AAQ1794 | 33 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAQ1795 | 34 | REDUCED GASKET SEAL |
| AAQ1796 | 35 | PLAIN |
| AAQ1797 | 36 | CRIMPED |
| AAQ1798 | 37 | GROOVED INSIDE |
| AAQ1799 | 38 | HOSE SOCKET |
| AAQ1800 | 39 | SOCKET W/BRAZING RING |
| AAQ1765 | 4 | SWIVEL NUT, GASKET SEAL |
| AAQ1801 | 40 | GASKET SEAL |
| AAQ1802 | 41 | BELL |
| AAQ1803 | 42 | DRESSER TYPE |
| AAQ1804 | 43 | DRESSER TYPE |
| AAQ1805 | 44 | PLAIN |
| AAQ1806 | 45 | GROOVED |
| AAQ1807 | 46 | BEADED |
| AAQ1808 | 47 | BEADED |
| AAQ1809 | 48 | SPIRALED |
| AAQ1810 | 49 | PLAIN BEVELED |
| AAQ1766 | 5 | GASKET SEAL |
| AAQ1811 | 50 | BARBED-BEADED |
| AAQ1812 | 51 | DOUBLE BEADED |
| AAQ1813 | 52 | MULTI-GROOVED |
| AAQ1814 | 53 | KNURLED |
| AAQ1767 | 6 | FLARE |
| AAQ1768 | 7 | INVERTED FLARE |
| AAQ1769 | 8 | SWIVEL NUT, COMPRESSION |
| AAQ1770 | 9 | SWIVEL NUT, FLARELESS |
IF STYLE/REPLY CODE(s) NC, NE, NF, NJ, NS, JC, JE, JF OR UN WERE ENTERED FOR MRC CLMW, YOU MUST ANSWER MRC (CLMX and CLMY and CLNB)
IF STYLE/REPLY CODE(s) BF, BW OR SS WERE ENTERED FOR MRC CLMW, YOU MUST ANSWER MRC (CLMX)
IF STYLE/REPLY CODE(s) BR, BS, NH, NP, NT, PE, PF, PM, PP, PS, PT, SC, SF, SH, SL, SP, AN OR FP WERE ENTERED FOR MRC CLMW, YOU MUST ANSWER MRC (CLMZ)
IF STYLE/REPLY CODE(s) SJ, SK, SM OR SS WERE ENTERED FOR MRC CLMW, YOU MUST ANSWER MRC (CTXG and CLMX)
CLMW*DPORT THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER ON THE PORT.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CLMW3AEEDSK*;CLMW3AEEDSK$DPM*;CLMW3AEEDSK$$DPM*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| NS | UNS |
CLMX*JPORT THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE PORT AND WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMX3AEEJAB2.0*;CLMX3AEEJAB2.0$JAB2.0*;CLMX3AEEJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3AGS | FIRST PORT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLMY*APORT THREAD QUANTITY PER INCH
A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE PORT PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CLMY3AGQAI4)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3AGS | FIRST PORT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CTXG*BPORT THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE PORT THREAD,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTXGB2.0*;CTXGB2.0$BM2.0;CTXGB2.0$$BM2.0*)
CLMZ*JPORT NOMINAL PIPE THREAD SIZE
THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE PORT PIPE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLMZJA2.0*;CLMZJA2.0$JA2.0*;CLMZJA2.0$$JA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CLNB*APORT THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL PORT THREAD.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CLNB3AGQAI4)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AJFY*BSEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(AJFY3AGRB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARXJAB2.0*;AARXJAB2.0$JAB2.0*;AARXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHE*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHE3AEEJAA2.0*;ABHE3AEEJAA2.0$JAA2.0*;ABHE3AEEJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABJH*JTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples.For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.If ISAC coding is authorized for this requirement and one or more of the temperature values in negative, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.Also precede the numeric portion of the reply with the letter “M” as in the fifth and sixth examples.
(ABJHJF68.0*; ABJHJC0.0$$JC35.0*; ABJHJFCM15.0*; ABJHJFM40.0$$JF75.0*; ABJH1BJFM25.0*; ABJH1BJCM35.0$$JCM5.0*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AGQ | SINGLE PORT |
| 3AGR | ALL PORTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BMWH*DRESERVOIR TYPE
INDICATES THE TYPE OF RESERVOIR PROVIDED.
Enter the applicable reply code from the table below
(BMWHDAAB)
| Table 1 |
| Reply Code (AM39) | Reply |
| AAB | INTEGRAL |
| BKM | REMOTE |
IF STYLE/REPLY CODE(s) ABW OR ABX WERE ENTERED FOR MRC CLNF, YOU MUST ANSWER MRC (ABWV and AGRC)
CLNF*DPEDAL SHAFT EXTENSION DIRECTION
AN INDICATION OF THE DIRECTION IN WHICH THE PEDAL SHAFT EXTENDS.
Enter the applicable reply code from the table below
(CLNFDABW)
| Table 1 |
| Reply Code (AM84) | Reply |
| ABW | LEFT |
| ABX | RIGHT |
ABWV*JSHAFT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABWVJAC2.0*;ABWVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGRC*JEXTENSION LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF AN EXTENSION,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGRCJAB2.0*;AGRCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) BF OR BW WERE ENTERED FOR MRC CLNG, YOU MUST ANSWER MRC (CLNH and CLNL)
IF STYLE/REPLY CODE(s) BR, BS, NH, NP, NP, NT, PE, PF, PM, PP, PS, PT, SC, SF, SH, SL, SP, AN OR FP WERE ENTERED FOR MRC CLNG, YOU MUST ANSWER MRC (CLNM)
IF STYLE/REPLY CODE(s) SJ, SK, SM OR SS WERE ENTERED FOR MRC CLNG, YOU MUST ANSWER MRC (CTXH and CLNH and CLNL)
IF STYLE/REPLY CODE(s) NC, NE, NF, NJ, NS, JC, JE, JF OR UN WERE ENTERED FOR MRC CLNG, YOU MUST ANSWER MRC (CLNH and CLNK and CLNL)
CLNG*DSTOPLIGHT SWITCH THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF STOPLIGHT SWITCH SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(CLNGDSP)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BF | BRITISH STANDARD FINE (BSF) |
| BW | BRITISH STANDARD WHITWORTH (BSW) |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| FP | F-PTF |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SC | NPSC |
| SF | NPSF |
| SH | NPSH |
| PS | NPSI |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| PT | PTF-SAE SHORT |
| PP | PTF-SPL |
| PE | PTF-SPL EXTRA SHORT |
| PF | PTF-SPL SHORT |
| SJ | SI |
| SK | SI-M |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNIFIED NATIONAL FINE (UNJ) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| JE | UNJEF |
| NS | UNS |
CLNH*JSTOPLIGHT SWITCH THREAD DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A STOPLIGHT SWITCH AND WOULD BOUND THE CREST OF AN EXTERNAL THREAD OR THE ROOT OF AN INTERNAL THREAD.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLNHJAC2.0*;CLNHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CLNK*ASTOPLIGHT SWITCH THREAD QUANTITY PER INCH
A MEASUREMENT OF THE NUMBER OF SCREW THREADS ON THE STOPLIGHT SWITCH PER LINEAR INCH,INCLUDING INCOMPLETE THREADS,ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CLNKAN1)
CTXH*BSTOPLIGHT SWITCH THREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREADED AXIS OF THE STOPLIGHT SWITCH,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CTXHB2.0)
CLNL*DSTOPLIGHT SWITCH THREAD DIRECTION
THE DIRECTION OF THE STOPLIGHT SWITCH THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(CLNLDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
CLNM*JSTOPLIGHT SWITCH NOMINAL PIPE THREAD SIZE
THE INDUSTRIAL SIZE DESIGNATION USED TO INDICATE THE DIAMETER OF THE STOPLIGHT SWITCH PIPE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLNMJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDAAGR*;CBBLDAKP$$DAKS*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AJZ | AIR PRESSURE RESERVOIR |
| AKA | BALL LOCK |
| AKS | BLEEDER VALVES |
| AKB | BY-PASS VALVE |
| AKC | CAM AND JACK SHAFT ASSEMBLY |
| AAGQ | CLEVIS PIN |
| AABK | CUSHIONED STROKE |
| AABL | FILLER PLUG |
| FEV | FIRST PISTON ROD END LUBRICATION FACILITY |
| EUM | FLOW METERING DEVICE |
| AABM | GEAR ADJUSTER |
| AKD | HYDRAULIC RESERVOIR |
| AAGR | HYDRO-LATCH LOCK |
| AKE | INTEGRAL LOCK |
| AKF | INTERNAL CHECK VALVE |
| AKG | LOCKING DEVICE |
| CRK | MANUAL OVERRIDE |
| AKH | MICRO SWITCH |
| AKJ | PISTON LOCK |
| AKK | PISTON LOCK-TOGGLE ASSEMBLY INDICATOR |
| CMR | PISTON ROD |
| AKL | POPPET |
| AKM | RELIEF VALVE |
| AABN | RUBBER BOOT |
| FEW | SECOND PISTON ROD END LUBRICATION FACILITY |
| AKN | SEQUENCE SWITCH |
| AABP | SERRATED ADJUSTER |
| AAGS | SHUTTLE VALVE |
| AKQ | SWITCH ACTUATOR |
| AKP | SWIVEL BLOCK |
| AKR | SWIVEL FITTINGS |
| EUL | TRANSDUCER |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDG4)
| Table 1 |
| Reply Code (EN02) | Reply |
| G4 | COMPREHENSIVE PROCUREMENT GUIDELINE - VEHICULAR PRODUCTS - REBUILT VEHICULAR PARTS |
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAD*;BBRJDAL$$DAK*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AB | CORROSIVE |
| AD | FLAMMABLE |
| AE | FRAGILE |
| AL | HUMIDITY CONTROLLED |
| AK | MAGNETIC |
| AM | SHOCK PROTECTED |
AFJN*DFRAGILITY FACTOR
THE MEASURE OF SENSITIVITY OF THE ITEM TO BE PACKAGED. A FACTOR USED BY PACKAGING ENGINEERS IN DEVISING PROPER CUSHIONING IN A PACKAGE.
Enter the applicable reply code from the table below
(AFJNDD)
| Table 1 |
| Reply Code (AD40) | Reply |
| D | DELICATE |
| B | EXTREMELY FRAGILE |
| E | MODERATELY DELICATE |
| F | MODERATELY RUGGED |
| G | RUGGED |
| C | VERY DELICATE |
ADZC*DENVIRONMENTAL PROTECTION
THE ENVIRONMENTAL ELEMENTS OR CONDITIONS THAT AN ITEM IS DESIGNED OR PROTECTED TO RESIST OR WITHSTAND SATISFACTORILY.
Enter the applicable reply code from the table below
(ADZCDBV*;ADZCDBQ$$DA*)
| Table 1 |
| Reply Code (AA65) | Reply |
| A | ANY ACCEPTABLE |
| GK | CORROSION RESISTANT |
| BV | DUSTPROOF |
| BW | EXPLOSION PROOF |
| BQ | VAPOR |
| AN | WATER, FRESH |
| AP | WATER, SALT |
| BX | WATERTIGHT |
| AR | WEATHERPROOF |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDCRA000*;SFTTDCRA000$DCRA000*;SFTTDCRA000$$DCRA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| CRA000 | CHROMIUM |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ222*;HZRDDHAZ052$$DHAZ092*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ008 | CADMIUM |
| HAZ222 | IRON |
| HAZ092 | MAGNESIUM |
| HAZ030 | MAGNESIUM ALLOY |
| HAZ052 | ZINC |
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3AEEDSTA000*;MATT3AEEDSTA000$DFE0044*;MATT3AEEDSTA000$$DFE0044*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| CUB000 | COPPER ALLOY |
| FEB000 | IRON CAST |
| FE0044 | IRON CAST UNS F11401 |
| FE0045 | IRON CAST UNS F11701 |
| FE0046 | IRON CAST UNS F12101 |
| FE0052 | IRON CAST UNS F12401 |
| FE0047 | IRON CAST UNS F12801 |
| FE0048 | IRON CAST UNS F13101 |
| FE0049 | IRON CAST UNS F13501 |
| FE0050 | IRON CAST UNS F13801 |
| FE0051 | IRON CAST UNS F14101 |
| STA000 | STEEL |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information