A unit designed to remove surface deposits of foreign materials by means of a forced stream of steam and detergent or water. Excludes:CLEANER, STEAM, PRESSURE JET, TRAILER MOUNTED; DISHWASHING MACHINE, COMMERCIAL; DISHWASHING MACHINE, HOUSEHOLD; and CLEANER, PRESSURE, SOLVENT-WATER.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED10239*)
BRXDDSTEAM GENERATOR
AN INDICATION OF WHETHER OR NOT A STEAM GENERATOR IS INCLUDED.
Enter the applicable reply code from the table below
(BRXDDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BXHW, YOU MUST ANSWER MRC (ANCY and BXHX)
BXHWDOUTSIDE STEAM SOURCE
AN INDICATION OF WHETHER OR NOT AN OUTSIDE STEAM SOURCE IS REQUIRED.
Enter the applicable reply code from the table below
(BXHWDB)
| Table 1 |
| Reply Code (AE40) | Reply |
| C | NOT REQUIRED |
| B | REQUIRED |
ANCY*BHORSEPOWER RATING
AN INDICATION OF THE RATED HORSEPOWER OF THE ITEM.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ANCYB2.0)
BXHX*JSTEAM PRESSURE RATING
THE AMOUNT OF STEAM PRESSURE FOR WHICH THE ITEM IS RATED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXHXJEYC2.0*;BXHXJEYC2.0$$JEYC2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| FB | POUNDS PER SQUARE INCH |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BXHYDOUTSIDE WATER SOURCE
AN INDICATION OF WHETHER OR NOT AN OUTSIDE WATER SOURCE IS REQUIRED.
Enter the applicable reply code from the table below
(BXHYDC)
| Table 1 |
| Reply Code (AE40) | Reply |
| C | NOT REQUIRED |
| B | REQUIRED |
IF YOU ANSWER MRC BXHZ, YOU MUST ANSWER MRC (BXJB)
BXHZ*JMAXIMUM CLEANING SOLUTION JET PRESSURE RATING
THE MAXIMUM AMOUNT OF CLEANING SOLUTION PRESSURE FOR WHICH THE JET IS RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXHZJFB2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| FB | POUNDS PER SQUARE INCH |
BXJB*JCLEANING SOLUTION MAXIMUM DISCHARGE RATE
THE MAXIMUM RATE OF CLEANING SOLUTION THE ITEM IS DESIGNED TO DISCHARGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXJBJGJ2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| LN | GALLONS PER HOUR |
| GJ | LITERS PER HOUR |
IF YOU ANSWER MRC BXJC, YOU MUST ANSWER MRC (BXJD)
BXJC*JMAXIMUM LIQUID JET PRESSURE RATING
THE MAXIMUM AMOUNT OF LIQUID PRESSURE FOR WHICH THE JET IS RATED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXJCJEY2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| EY | KILOGRAMS PER SQUARE CENTIMETER |
| FB | POUNDS PER SQUARE INCH |
BXJD*JMAXIMUM LIQUID DISCHARGE RATE
THE MAXIMUM RATE OF LIQUID THE ITEM IS DESIGNED TO DISCHARGE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXJDJLN2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| LN | GALLONS PER HOUR |
| GJ | LITERS PER HOUR |
IF YOU ANSWER MRC BXJF, YOU MUST ANSWER MRC (BXJG and AJCB and BTLN and AYHT)
BXJF*ACLEANING GUN QUANTITY
THE NUMBER OF CLEANING GUNS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BXJFA10*)
BXJG*DNOZZLE ADJUSTABILITY
AN INDICATION OF WHETHER OR NOT THE NOZZLE IS ADJUSTABLE.
Enter the applicable reply code from the table below
(BXJGDA)
| Table 1 |
| Reply Code (AB00) | Reply |
| A | ADJUSTABLE |
| C | NONADJUSTABLE |
AJCB*DHAZARD PROTECTION FEATURE
THE FEATURE INHERENT IN OR DESIGNED INTO THE ITEM AS PROTECTION AGAINST RISKS ENCOUNTERED DURING USAGE.
Enter the applicable reply code from the table below
(AJCBDCU)
| Table 1 |
| Reply Code (AA65) | Reply |
| CT | NONMAGNETIC |
| CU | NONSPARKING |
BTLN*AHOSE CONNECTION QUANTITY
THE NUMBER OF HOSE CONNECTIONS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BTLNA10*)
AYHT*JHOSE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE HOSE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AYHTJFC2.0*;AYHTJFC2.0$$JFC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| F | FEET |
| M | METERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BDWT*DHEATING METHOD
THE MEANS BY WHICH THE ITEM IS HEATED.
Enter the applicable reply code from the table below
(BDWTDAB*;BDWTDAM$DAN*)
| Table 1 |
| Reply Code (AM63) | Reply |
| A | ANY ACCEPTABLE |
| AL | DIESEL OIL |
| AB | ELECTRICAL |
| AG | GAS |
| AM | GASOLINE |
| BA | JET FUEL |
| AC | KEROSENE |
| AE | NATURAL GAS |
| AN | OIL |
NMBR*AQUANTITY
A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.
Enter the numeric reply with a minimum of one digit.
(NMBRA10*)
BYYP*BPOWER SOURCE HORSEPOWER RATING
THE RATED HORSEPOWER OF THE POWER SOURCE.
Enter a reply with a minimum of one digit on either side of the decimal point.
(BYYPB2.0)
CSBHJVOLTAGE IN VOLTS AND CURRENT TYPE
THE TOTAL ELECTRICAL VOLTAGE,EXPRESSED IN VOLTS,AND THE TYPE OF CURRENT WHETHER ALTERNATING OR DIRECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSBHJDC2.0*;CSBHJDC2.0$$JDC2.1*)
| Table 1 |
| Reply Code (AN87) | Reply |
| AC | AC |
| AD | AC/DC |
| DC | DC |
FREQ*BFREQUENCY IN HERTZ
THE CYCLES PER SECOND /HERTZ/ OF THE ALTERNATING CURRENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(FREQB2.0*;FREQB2.0$$BM2.0*)
FAAZ*DPHASE
THE NUMBER OF ALTERNATING CURRENT PHASES.
Enter the applicable reply code from the table below
(FAAZDE)
| Table 1 |
| Reply Code (AD02) | Reply |
| A | SINGLE |
| E | SINGLE/THREE |
| C | THREE |
| B | TWO |
AAXZ*ACYLINDER QUANTITY
THE NUMBER OF CYLINDERS INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AAXZA10*)
BFMF*DCOOLING METHOD
THE MEANS OF COOLING USED TO MAINTAIN THE REQUIRED OPERATING TEMPERATURE OF THE ITEM.
Enter the applicable reply code from the table below
(BFMFDAAR)
| Table 1 |
| Reply Code (AN05) | Reply |
| AAR | AIR |
| AAQ | LIQUID |
IF YOU ANSWER MRC AENC, YOU MUST ANSWER MRC (BFDM)
AENC*APUMP QUANTITY
THE NUMBER OF PUMPS INCORPORATED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AENCA10*)
BFDM*JPUMP CAPACITY
THE RATED CAPACITY OF THE PUMP.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BFDMJLNB2.0*;BFDMJLNB2.0$$JLNB2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| LN | GALLONS PER HOUR |
| GJ | LITERS PER HOUR |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF YOU ANSWER MRC BXJJ, YOU MUST ANSWER MRC (BXJK and AXQD)
BXJJ*ASTORAGE TANK QUANTITY
THE NUMBER OF STORAGE TANKS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BXJJA10*)
BXJK*DSTORED MATERIAL
AN INDICATION OF THE MATERIAL THAT IS STORED.
Enter the applicable reply code from the table below
(BXJKDAAL*;BXJKDAAJ$$DAAE*)
| Table 1 |
| Reply Code (AN44) | Reply |
| A | ANY ACCEPTABLE |
| AAB | CLEANING SOLUTION |
| AAC | DETERGENT |
| AAD | FUEL |
| AAE | GASOLINE |
| AAF | LIQUID SOAP |
| AAG | PREMIXED SOAP |
| AAH | SOAP |
| AAJ | SOAP CONCENTRATE |
| AAK | SOLUTION |
| AAL | WATER |
AXQD*JCAPACITY
A MEASUREMENT OF THE CAPACITY OF AN ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXQDJAF2.0*;AXQDJAF2.0$$JAF2.1*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AF | GALLONS |
| CC | LITERS |
IF STYLE/REPLY CODE(s) AU WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (AGDH and ALRE and BXJL)
IF STYLE/REPLY CODE(s) AV WERE ENTERED FOR MRC AAXX, YOU MUST ANSWER MRC (AZBT and AGDH and ALRE and BXJL)
AAXXDMOUNTING TYPE
INDICATES THE TYPE OF MOUNT UTILIZED TO SUPPORT THE ITEM.
Enter the applicable reply code from the table below
(AAXXDPY*;AAXXDAV$DA*)
| Table 1 |
| Reply Code (AA78) | Reply |
| A | ANY ACCEPTABLE |
| BF | BASE |
| AT | SKID |
| PY | STEAM LINE |
| AV | TRAILER |
| AU | WHEEL |
AGDH*AWHEEL QUANTITY
THE NUMBER OF WHEELS INCLUDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AGDHA10*)
IF STYLE/REPLY CODE(s) AD WERE ENTERED FOR MRC ALRE, YOU MUST ANSWER MRC (AGEC)
IF STYLE/REPLY CODE(s) AB, AC OR AN WERE ENTERED FOR MRC ALRE, YOU MUST ANSWER MRC (BCDX)
ALRE*DTIRE TYPE
INDICATES THE TYPE OF TIRE(S) PROVIDED.
Enter the applicable reply code from the table below
(ALREDAD)
| Table 1 |
| Reply Code (AH67) | Reply |
| A | ANY ACCEPTABLE |
| AD | PNEUMATIC |
| AP | RUBBER |
| AN | SEMISTEEL |
| AB | SOLID RUBBER |
| AC | STEEL |
AGEC*DTIRE SIZE
DESIGNATES THE SIZE BY WHICH THE TIRE IS COMMERCIALLY KNOWN AND DESIGNATED.
Enter the applicable reply code from the table below
(AGECDA)
| Table 1 |
| Reply Code (AA27) | Reply |
| AX | 4.80/4.00-8 |
| WL | 6.00X9 |
| CT | 6.70-15 |
| CV | 7.00-15 |
| DQ | 7.00-16 |
| A | ANY ACCEPTABLE |
BCDX*JWHEEL DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE WHEEL,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BCDXJAA2.0*;BCDXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AZBT*LWHEEL ARRANGEMENT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE ARRANGEMENT OF THE WHEEL(S).
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AZBTL8)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1590 | 1 | MIDDLE, SINGLE |
| AAH1591 | 2 | SEMI REAR, SINGLE |
| AAH1592 | 3 | REAR, SINGLE |
| AAH1593 | 4 | MIDDLE TANDEM, SINGLE |
| AAH1594 | 5 | REAR TANDEM, SINGLE |
| AAH1595 | 6 | FRONT AND REAR, SINGLE |
| AAH1596 | 7 | FRONT TRIYCYCLE, SINGLE, REAR, SINGLE |
| AAH1597 | 8 | FRONT, SINGLE, REAR TANDEM, SINGLE |
| AAH1598 | 9 | MIDDLE, SEMI REAR AND REAR, SINGLE |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BXJL, YOU MUST ANSWER MRC (AFBT)
BXJL*DRETRACTABLE SUPPORT FEATURE
AN INDICATION OF WHETHER OR NOT A RETRACTABLE SUPPORT FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(BXJLDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AFBT, YOU MUST ANSWER MRC (BJHJ and BJHK and BXJM and BXJN)
AFBT*DCASTERS
AN INDICATION OF WHETHER OR NOT CASTERS ARE INCLUDED WITH THE ITEM. IF INCLUDED PLEASE USE MRC ABFF IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AFBTDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
BJHJ*ACASTER QUANTITY
THE NUMBER OF CASTERS PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(BJHJA10*)
BJHK*DCASTER TYPE
INDICATES THE TYPE OF CASTERS PROVIDED.
Enter the applicable reply code from the table below
(BJHKDAF)
| Table 1 |
| Reply Code (AL49) | Reply |
| A | ANY ACCEPTABLE |
| AF | RIGID |
| AG | SWIVEL |
BXJM*JCASTER WHEEL DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE CASTER WHEEL,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BXJMJAC2.0*;BXJMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BXJN*DCASTER TIRE TYPE
INDICATES THE TYPE OF TIRE PROVIDED ON THE CASTER(S).
Enter the applicable reply code from the table below
(BXJNDA)
| Table 1 |
| Reply Code (AH67) | Reply |
| A | ANY ACCEPTABLE |
| AD | PNEUMATIC |
| AN | SEMISTEEL |
| AB | SOLID RUBBER |
| AC | STEEL |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAX2)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAX1)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CM | CUBIC METERS |
IF STYLE/REPLY CODE(s) AD WERE ENTERED FOR MRC AWZJ, YOU MUST ANSWER MRC (NMBR and BYYP)
IF STYLE/REPLY CODE(s) AE WERE ENTERED FOR MRC AWZJ, YOU MUST ANSWER MRC (NMBR and BYYP and AAXZ and BFMF)
AWZJ*DPOWER SOURCE
THE SOURCE OF POWER WHICH PROVIDES THE ENERGY REQUIRED FOR THE OPERATION OF THE ITEM.
Enter the applicable reply code from the table below
(AWZJDAE)
| Table 1 |
| Reply Code (AG27) | Reply |
| AC | DIESEL ENGINE |
| AD | ELECTRIC MOTOR |
| AE | GASOLINE ENGINE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information