Table 1
	Reply Code (AF70)	Reply
	BD	BILL OF MATERIAL
	BE	CATALOG SHEET
	CD	COMMERCIAL CATALOG
	CH	DESIGN CONTROL DRAWING
	AN	ENGINEERING DRAWING
	BG	ENGINEERING PARTS LIST
	CF	FEDERAL SUPPLY CATALOG
	BK	INDUSTRIAL DRAWING
	AT	INSTRUCTION MANUAL
	BN	MILITARY DRAWING
	AC	MILITARY SPECIFICATION
	AF	MILITARY STANDARD
	BT	PARTS LIST
	FE	SOURCE CONTROL DRAWING
	AB	TECHNICAL MANUAL
	AG	TECHNICAL ORDER

HUES*DCOLOR

A CHARACTERISTIC OF LIGHT THAT CAN BE SPECIFIED IN TERMS OF LUMINANCE,DOMINANT WAVELENGTH,AND PURITY.

Enter the applicable reply code from the table below

(HUESDGY0002*;HUESDGY0000$DBL0000*;HUESDGY0000$$DBL0000*)

Table 1
	Reply Code (AD06)	Reply
	BL0000	BLACK
	GY0002	GRAY, LIGHT
	GY0000	GRAY/GREY

IF YOU ANSWER MRC HDCL, YOU MUST ANSWER MRC (HUES)

HDCL*JCOLOR DOCUMENT AND CLASSIFICATION

THE SPECIFICATION,STANDARD,MANUFACTURERS REFERENCE,OR INDEX SYSTEM AND THE CLASIFICATION DESIGNATION, USED TO IDENTIFY COLOR, COLOR SELECTION, COLOR MATCHING AND QUALITY CONTROL OF A SPECIFIC COLOR.

Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.

(HDCLJEATEXT1234*;HDCLJEATEXT1234$$JEATEXT1234*;HDCLJEATEXT1234$JEATEXT1234*;HDCL1BJEATEXT1234*;HDCL1BJEATEXT1234$$JEATEXT1234*;HDCL1BJEATEXT1234$JEATEXT1234*)

Table 1
	Reply Code (AP33)	Reply
	Q	AEROSPACE MATERIAL SPEC STD
	J	AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
	G	ASSN STD
	K	DEF STAN/SPEC
	B	FED SPEC
	C	FED STD
	L	GOVERNMENT STD/SPEC
	N	INTERNATIONAL STD/SPEC
	F	MFR REF
	D	MIL SPEC
	E	MIL STD
	H	NATIONAL SPEC
	P	NATIONAL STD
	M	NATIONAL STD/SPEC

Table 2
	Reply Code (AP93)	Reply
	M	10TH COLOR RESPONSE
	N	11TH COLOR RESPONSE
	P	12TH COLOR RESPONSE
	Q	13TH COLOR RESPONSE
	R	14TH COLOR RESPONSE
	S	15TH COLOR RESPONSE
	T	16TH COLOR RESPONSE
	U	17TH COLOR RESPONSE
	W	18TH COLOR RESPONSE
	X	19TH COLOR RESPONSE
	B	1ST COLOR RESPONSE
	Y	20TH COLOR RESPONSE
	Z	21ST COLOR RESPONSE
	V	22ND COLOR RESPONSE
	C	2ND COLOR RESPONSE
	D	3RD COLOR RESPONSE
	E	4TH COLOR RESPONSE
	F	5TH COLOR RESPONSE
	H	6TH COLOR RESPONSE
	J	7TH COLOR RESPONSE
	K	8TH COLOR RESPONSE
	L	9TH COLOR RESPONSE
	G	ALL COLOR RESPONSE
	A	SINGLE COLOR RESPONSE

MATT*DMATERIAL

THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.

Enter the applicable reply code from the table below

(MATTDRCB000*;MATTDPCA000$DPCCB00*;MATTDPCA000$$DPCCB00*)

Table 1
	Reply Code (MA01)	Reply
	PCA000	PLASTIC
	PCCB00	PLASTIC NYLON
	PCAH00	PLASTIC POLYURETHANE
	RCB000	RUBBER SYNTHETIC
	AAA012	THERMOPLASTIC

Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.

MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION

THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.

(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)

Table 1
	Reply Code (AP33)	Reply
	Q	AEROSPACE MATERIAL SPEC STD
	J	AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
	G	ASSN STD
	A	COMMERCIAL ITEM DESCRIPTION
	K	DEF STAN/SPEC
	B	FED SPEC
	C	FED STD
	L	GOVERNMENT STD/SPEC
	N	INTERNATIONAL STD/SPEC
	F	MFR REF
	D	MIL SPEC
	E	MIL STD
	H	NATIONAL SPEC
	P	NATIONAL STD
	M	NATIONAL STD/SPEC

Table 2
	Reply Code (AP18)	Reply
	M	10TH MATERIAL RESPONSE
	N	11TH MATERIAL RESPONSE
	P	12TH MATERIAL RESPONSE
	Q	13TH MATERIAL RESPONSE
	R	14TH MATERIAL RESPONSE
	S	15TH MATERIAL RESPONSE
	T	16TH MATERIAL RESPONSE
	U	17TH MATERIAL RESPONSE
	W	18TH MATERIAL RESPONSE
	X	19TH MATERIAL RESPONSE
	B	1ST MATERIAL RESPONSE
	Y	20TH MATERIAL RESPONSE
	Z	21ST MATERIAL RESPONSE
	V	22ND MATERIAL RESPONSE
	C	2ND MATERIAL RESPONSE
	D	3RD MATERIAL RESPONSE
	E	4TH MATERIAL RESPONSE
	F	5TH MATERIAL RESPONSE
	H	6TH MATERIAL RESPONSE
	J	7TH MATERIAL RESPONSE
	K	8TH MATERIAL RESPONSE
	L	9TH MATERIAL RESPONSE
	G	ALL MATERIAL RESPONSES
	A	SINGLE MATERIAL RESPONSE

TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION

A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.

Enter clear text.

(TEXTGCLEARTEXT)

FTLD*GFUNCTIONAL DESCRIPTION

DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.

Enter the reply from the applicable document.

(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)

AKYD*GACCESSORY COMPONENTS AND QUANTITY

THE NAME AND NUMBER OF PARTS SUPPLIED WITH THE ITEM WHICH MAY BE REQUIRED FOR APPLICATION.

Enter clear text.

(AKYDGCLEARTEXT)

ADAV*JOVERALL DIAMETER

A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ADAVJLA2.0*;ADAVJLA2.0$$JLA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABHP*JOVERALL LENGTH

THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABKW*JOVERALL HEIGHT

THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABKWJLB2.0*;ABKWJLB2.0$$JLB2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

ABMK*JOVERALL WIDTH

AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.

Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.

(ABMKJLA2.0*;ABMKJLA2.0$$JLA2.1*)

Table 1
	Reply Code (AA05)	Reply
	A	INCHES
	L	MILLIMETERS

Table 2
	Reply Code (AC20)	Reply
	A	NOMINAL
	B	MINIMUM
	C	MAXIMUM

AMWN*AMODEL NUMBER

THE COMBINED GROUP OF LETTERS,NUMERALS,AND/OR SYMBOLS WHICH COMPOSE THE ASSIGNED MODEL NUMBER OF THE ITEM.

Enter the alpha-numeric reply with a minimum of one character.

(AMWNAS7)

MARK*GSPECIAL MARKINGS

MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.

Enter clear text.

(MARKGCLEARTEXT)

Reply to this MRC in accordance with Volume 3.

AGAV*GEND ITEM IDENTIFICATION

THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.

Enter the reply in clear text.

(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)

FEAT*GSPECIAL FEATURES

THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.

Enter the reply in clear text. Separate multiple replies with a semicolon.

(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)

TEST*JTEST DATA DOCUMENT

THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.

Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.

(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)

Table 1
	Reply Code (AC28)	Reply
	A	SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
	B	STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.).
	C	DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING)

Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.

CRTL*ACRITICALITY CODE JUSTIFICATION

THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.

Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.

(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)

If document availability code B, D, F, OR H, reply to MRC PRPY.

PRPY*APROPRIETARY CHARACTERISTICS

IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.

Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.

(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)

ELRN*GEXTRA LONG REFERENCE NUMBER

A REFERENCE NUMBER EXCEEDING 32 POSITIONS.

Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.

(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)

In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.

ZZZK*JSPECIFICATION/STANDARD DATA

THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.

Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.

(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)

Table 1
	Reply Code (AN62)	Reply
	V	FEDERAL MOTOR VEHICLE SAFETY STANDARD
	F	FLAMMABILITY STANDARD
	S	GOVERNMENT SPECIFICATION
	T	GOVERNMENT STANDARD
	U	INTERNATIONAL STD/SPEC
	D	MANUFACTURERS SOURCE CONTROL
	R	MANUFACTURERS SPECIFICATION
	N	MANUFACTURERS SPECIFICATION CONTROL
	M	MANUFACTURERS STANDARD
	B	NATIONAL STD/SPEC
	A	PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION
	P	PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD

If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.

ZZZT*JNONDEFINITIVE SPEC/STD DATA

THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.

Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.

(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)

Table 1
	Reply Code (AD08)	Reply
	AL	ALLOY
	BE	ANNEALED
	AN	ANNEX
	AP	APPENDIX
	AC	APPLICABILITY CLASS
	AR	ARRANGEMENT
	AS	ASSEMBLY
	AB	ASSORTMENT
	BF	BOND
	BX	BOX
	CY	CAPACITY
	CA	CASE
	CT	CATEGORY
	CF	CIRCUMFERENCE
	CL	CLASS
	CE	CODE
	CR	COLOR
	CC	COMBINATION CODE
	CN	COMPONENT
	CP	COMPOSITION
	CM	COMPOUND
	CD	CONDITION
	AV	CONFIGURATION
	CS	CONSTRUCTION
	BG	CORE CONDITION
	CB	CUT OFF
	AM	DELAY CLASS
	DE	DESIGN
	DG	DESIGNATOR
	DW	DRAWING NUMBER
	DU	DUPLEX
	EG	EDGE
	EN	END
	FY	FAMILY
	FG	FIGURE
	AK	FILE NUMBER
	FN	FINISH
	FB	FLAVOR
	BH	FLUX PERCENTAGE
	FM	FORM
	FA	FORMULA
	AJ	GAGE STOCK NUMBER
	GR	GRADE
	GA	GRADUATION
	AX	GRANULES
	AY	GRIT
	GB	GROUND
	GP	GROUP
	HA	HEAVY DUTY
	BA	IMAGE COLOR
	NS	INSERT
	TM	ITEM
	KD	KIND
	KT	KIT
	LG	LENGTH
	LV	LEVEL
	LT	LIMIT
	MK	MARK
	AA	MARKER
	AD	MASK APERTURE
	ML	MATERIAL
	BB	MAXIMUM DENSITY
	TA	MEDIUM TEMPER
	MH	MESH
	ME	METHOD
	BC	MINIMUM DENSITY
	MD	MODEL
	MT	MOUNTING
	AQ	NATURAL
	AU	NON-DELAY CLASS
	NR	NUMBER
	BL	OUTFIT NUMBER
	PA	PARAGRAPH
	PT	PART
	PN	PATTERN
	PC	PHYSICAL CONDITION
	PS	PIECE
	PL	PLAN
	PR	POINT
	PD	POLISHED
	PB	PRESSURE RATING
	QA	QUALITY
	QB	QUENCHED
	RN	RANGE
	AE	RAPID
	RT	RATING
	RF	REFERENCE NUMBER
	RA	REGULAR DUTY
	BJ	RMA FLUX
	SJ	SALIENT CHARACTERISTICS
	SC	SCHEDULE
	SB	SECTION
	SL	SELECTION
	BD	SERIALIZED
	SE	SERIES
	SV	SERVICE
	SX	SET
	SA	SHADE
	SH	SHAPE
	SG	SHEET
	SZ	SIZE
	AG	SLOW
	TC	SOFT TEMPER
	SK	SOURCE
	PZ	SPECIES
	SQ	SPECIFICATION SHEET
	SD	SPEED
	AW	STANDARD
	SR	STRAIGHT
	ST	STYLE
	SS	SUBCLASS
	SF	SUBFORM
	SP	SUBTYPE
	BK	SUPPORT
	SN	SURFACE CONDITION
	SY	SYMBOL
	SM	SYSTEM
	TB	TABLE
	TN	TANNAGE
	TP	TEMPER
	TX	TEXTURE
	TK	THICKNESS
	TT	TREATMENT
	TR	TRIM
	TY	TYPE
	YN	UNIT
	AZ	UNSERIALIZED
	VA	VARIETY
	WT	WEIGHT
	WD	WIDTH

ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS

A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.

Enter the reply in clear text.

(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)

CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY

THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.

Enter the reply in clear text.

(CXCYGLINE PROCESSOR CONTROL BOARD*)

CLQL*GCOLLOQUIAL NAME

A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.

Enter the reply in clear text.

(CLQLGWOVEN WIRE CLOTH*)