A series of interconnected metal links forming two or more parallel lengths, cross-connected, usually at right angles. Designed to be fastened over the tread or perimeter of a tire(s) of a vehicle to increase traction and/or prevent skidding.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED08918*)
ALBYDUSAGE DESIGN
INDICATES THE DESIGNED USE OF THE ITEM.
Enter the applicable reply code from the table below
(ALBYDAQD)
| Table 1 |
| Reply Code (AH21) | Reply |
| AQC | DUAL TIRE |
| AQD | SINGLE TIRE |
CQJNDTIRE SIZE ACCOMMODATED
THE TIRE SIZE/S/ THAT THE ITEM WILL ACCOMMODATE.
Enter the applicable reply code from the table below
(CQJNDABLL*;CQJNDABRA$DAAMC*)
| Table 1 |
| Reply Code (AA27) | Reply |
| AAQQ | 10.00-15 |
| AAED | 10.00-16 |
| AAFD | 10.00-18 |
| AAFX | 10.00-20 |
| AAGG | 10.00-22 |
| AAHE | 10.00-24 |
| ADWY | 10.22-5 |
| ABLM | 10.3-22.5 |
| AAXT | 10.50-18 |
| ABLY | 10-1/2X5X5 |
| ABLZ | 10-1/2X5X6-1/2 |
| ABLN | 10-1/2X6 |
| ABMA | 10-1/2X6X5 |
| ABMB | 10-1/2X6X6-1/2 |
| ADWX | 10-15 |
| ABFJ | 10-16.5 |
| AAXS | 10-17.5 |
| ABFL | 10-22.5 |
| AALK | 10X2.00 |
| AALP | 10X2.75 |
| ABLP | 10X2-1/2 |
| ABLR | 10X3-1/2X6 |
| ABLQ | 10X3X6-1/4 |
| ABLS | 10X4X6-1/4 |
| ABLT | 10X5X6-1/2 |
| ABLW | 10X6X6-1/4 |
| ABLX | 10X7X6-1/4 |
| AABZ | 11.00-12 |
| AAQW | 11.00-15 |
| AAQX | 11.00-18 |
| ACAT | 11.00-19 |
| AAFY | 11.00-20 |
| AAGH | 11.00-22 |
| AAHG | 11.00-24 |
| AAYB | 11.00-25 |
| ADWZ | 11.22-5 |
| ADXA | 11.24-5 |
| AAHH | 11.25-24 |
| AARA | 11.25-28 |
| ABMD | 11.50-20 |
| ABME | 11.50-22 |
| ABMC | 11.5-22.5 |
| ABFN | 11-22.5 |
| AAHS | 11-24.5 |
| AARC | 11L-14 |
| AARD | 11L-15 |
| AARE | 11L-16 |
| ABMF | 11X2-1/2 |
| ABMG | 11X2-1/2X8 |
| AARF | 11X4.00-5 |
| AAFZ | 12.00-20 |
| AAGD | 12.00-21 |
| AAGJ | 12.00-22 |
| AAHK | 12.00-24 |
| AAYG | 12.00-25 |
| AAJR | 12.00-28 |
| ADXB | 12.22-5 |
| ADXC | 12.24-5 |
| AARG | 12.4-16 |
| AARH | 12.4-24 |
| AARJ | 12.4-26 |
| AARK | 12.4-28 |
| ABMH | 12.4-36 |
| AARL | 12.4-38 |
| ABMJ | 12.4-40 |
| ABMK | 12.4-42 |
| AAEG | 12.50-16 |
| ABMM | 12.50-20 |
| ABML | 12.5-22.5 |
| AARM | 12.5L-15 |
| AARN | 12.5L-16 |
| ABFP | 12-16.5 |
| ABFQ | 12-22.5 |
| AAHT | 12-24.5 |
| AALR | 12X3.00 |
| ABMN | 12X3-1/2 |
| ABMP | 12X3-1/2X8 |
| ABMQ | 12X4-1/2X8 |
| AAYP | 12X4X8 |
| AAGA | 13.00-20 |
| AAHM | 13.00-24 |
| AAHX | 13.00-25 |
| AAKG | 13.00-32 |
| AARW | 13.50-16.1 |
| ABMR | 13.5-24.5 |
| ABMS | 13.6-24 |
| ABMT | 13.6-26 |
| ABMW | 13.6-28 |
| AAKY | 13.9-36 |
| ABNB | 13-1/2X3-1/2X8 |
| ABNC | 13-1/2X4-1/2X8 |
| ABND | 13-1/2X5-1/2X8 |
| ABMX | 13L6-38 |
| ABMY | 13X3-1/2X8 |
| ABMZ | 13X4-1/2X8 |
| ABNA | 13X5.00-6 |
| AARZ | 14.00-20 |
| AAGE | 14.00-21 |
| AAHN | 14.00-24 |
| AAHY | 14.00-25 |
| AAJY | 14.00-28 |
| AAKH | 14.00-32 |
| AASA | 14.9-24 |
| AASB | 14.9-26 |
| ABNE | 14.9-28 |
| ABNF | 14.9-30 |
| ABNG | 14.9-36 |
| ABNH | 14.9-38 |
| AASC | 14-17.5 |
| ABNJ | 14-9.5 |
| ABNK | 14L-16.1 |
| ABNL | 14X2-1/2 |
| ABNM | 14X3-1/2 |
| ABNN | 14X3X10 |
| ABNP | 14X4-1/2X8 |
| AAZK | 14X4X10 |
| AASF | 15.5-25 |
| AALB | 15.5-38 |
| ABNZ | 15-1/2X5X10 |
| ABPA | 15-1/2X6X10 |
| AASH | 15-19.5 |
| AASJ | 15-22.5 |
| AAZT | 15X10X11-1/4 |
| ABNR | 15X3-1/2X11-1/4 |
| ABNQ | 15X3X11-1/4 |
| ABNT | 15X5X11-1/4 |
| AASK | 15X6.00-6 |
| ABNW | 15X6X11-1/4 |
| ABNX | 15X7X11-1/4 |
| ABNY | 15X8X11-1/4 |
| AAZW | 15X9X11-1/4 |
| AAGC | 16.00-20 |
| AAGF | 16.00-21 |
| AAHQ | 16.00-24 |
| AAHZ | 16.00-25 |
| AAZY | 16.5-19.5 |
| AAGS | 16.5-22.5 |
| AASL | 16.5L-16.1 |
| AASM | 16.9-24 |
| AASN | 16.9-26 |
| ABPB | 16.9-28 |
| ABPC | 16.9-30 |
| ABPD | 16.9-32 |
| AASP | 16.9-34 |
| AASQ | 16.9-38 |
| ABPQ | 16-1/4X4X11-1/4 |
| ABPR | 16-1/4X5X11-1/4 |
| ABPS | 16-1/4X6X11-1/4 |
| ABPT | 16-1/4X7X11-1/4 |
| ADLN | 165-R13 |
| ABPE | 16X2-1/2 |
| ABPF | 16X2-1/2X13-3/4 |
| ABAA | 16X3-1/2X12-1/8 |
| ABPG | 16X3X12 |
| AALX | 16X4.00 |
| AALY | 16X4.4 |
| ABPJ | 16X4-1/2X10-1/2 |
| ABPK | 16X4-1/2X12 |
| ABPL | 16X4-1/2X12-1/8 |
| ABPH | 16X4X12-1/8 |
| ABPM | 16X5X10-1/2 |
| AAST | 16X6.50-8 |
| ABPN | 16X6X10-1/2 |
| ABPP | 16X7X10-1/2 |
| AASW | 17.5-25 |
| ABQA | 17-3/4X5X12-1/8 |
| ABQB | 17-3/4X6X12-1/8 |
| ADMM | 175-R13 |
| ABPW | 17X4-1/2X12-1/4 |
| ABPX | 17X5X12-1/8 |
| ABPY | 17X6X12-1/8 |
| ABPZ | 17X7X12-1/8 |
| AAJA | 18.00-25 |
| AAJP | 18.00-26 |
| AAKK | 18.00-33 |
| AALE | 18.00-49 |
| AASZ | 18.4-16.1 |
| ABQC | 18.4-24 |
| ABQD | 18.4-26 |
| ABQE | 18.4-28 |
| ABQF | 18.4-30 |
| ABQG | 18.4-34 |
| AATA | 18.4-38 |
| AATC | 18-19.5 |
| ABQH | 18-21 |
| AATD | 18-22.5 |
| AAAU | 185/65-R15 |
| ABQJ | 18-9.50X8 |
| ABQK | 18X12X14 |
| ABQL | 18X2-1/2 |
| ABQM | 18X3-1/2 |
| ABQN | 18X3X14 |
| ABQQ | 18X4-1/2X12-1/8 |
| ABQP | 18X4X14 |
| AAMC | 18X5.5 |
| ABQR | 18X5X12-1/8 |
| ABAD | 18X5X14 |
| ABQS | 18X6X12-1/8 |
| ABQT | 18X7X12-1/8 |
| ABQW | 18X7X14 |
| ABQX | 18X8.50-8 |
| ABQY | 18X8X12-1/8 |
| AATF | 18X9.50-8 |
| ABQZ | 18X9X12-1/8 |
| AATG | 19.5-19.5 |
| ABRA | 19.5-21 |
| ABRB | 2.25-17 |
| ABRC | 2.50-16 |
| ABRD | 2.50-17 |
| ABRE | 2.50-18 |
| ABRF | 2.75-17 |
| ABRG | 2.75-18 |
| AAAC | 2.80/2.50-4 |
| AATK | 20.5-25 |
| ABRP | 20-1/2X7X17-3/4 |
| ABRH | 20X4X16 |
| ABRJ | 20X5X16 |
| ABRK | 20X6X16 |
| ABRL | 20X7X16 |
| ABRM | 20X8X16 |
| ABRN | 20X9X16 |
| AAJB | 21.00-25 |
| AAKA | 21.00-29 |
| AAKT | 21.00-35 |
| AALF | 21.00-49 |
| ABRQ | 21X5X15 |
| ABRR | 21X6X15 |
| ABRS | 21X7X15 |
| ABRT | 21X8X15 |
| ABRW | 21X9X15 |
| ABRX | 22X10X16 |
| ABAN | 22X10X17-3/4 |
| ABRY | 22X12X16 |
| ABRZ | 22X14X16 |
| ABSA | 22X16X16 |
| ABSB | 22X4-1/2X16 |
| ABSC | 22X4-1/2X17-3/4 |
| AAMF | 22X5.5 |
| ABSD | 22X5X16 |
| ABSE | 22X6X16 |
| ABAP | 22X6X17-3/4 |
| ABSF | 22X7X16 |
| ABAQ | 22X7X17-3/4 |
| ABSG | 22X8X16 |
| ABAS | 22X8X17-3/4 |
| ABSH | 22X9X16 |
| ABSJ | 23.1-26 |
| AATN | 23.1-30 |
| AATP | 23.1-34 |
| AATQ | 23.5-25 |
| ABSK | 23-21 |
| ABSL | 23-23.5 |
| ABSM | 23-3/4X8X17-3/4 |
| ADRT | 235-R15 |
| ABAT | 23X8.50-12 |
| AAJC | 24.00-25 |
| AAKB | 24.00-29 |
| AATS | 24.00-35 |
| AATT | 24.00-49 |
| AAKJ | 24.5-32 |
| ABSN | 24X4X20 |
| ABAW | 24X5X18 |
| ABAY | 24X7X20 |
| AATW | 26.5-25 |
| AATX | 26.5-29 |
| ABSP | 26X5X20 |
| ABSQ | 26X7X20 |
| AAKM | 27.00-33 |
| AATZ | 27.00-49 |
| ABSR | 27X10.00-12 |
| AAVA | 27X8.50-15 |
| ABSS | 28X10X22 |
| ABST | 28X12X22 |
| ABSW | 28X14X22 |
| ABSX | 28X16X22 |
| ABSY | 28X7X22 |
| ABSZ | 28X7X23-1/2 |
| AAVB | 29.5-25 |
| AAVC | 29.5-29 |
| ABTA | 29.5-33 |
| ABTB | 29.5-35 |
| ABBG | 3.00-12 |
| ABTD | 3.00-16 |
| ABTE | 3.00-17 |
| ABTF | 3.00-18 |
| ABTG | 3.00-19 |
| ABTH | 3.25-16 |
| ABTJ | 3.25-17 |
| ABTK | 3.25-18 |
| AAFE | 3.25-19 |
| AABP | 3.50-12 |
| ABTL | 3.50-16 |
| ABTM | 3.50-17 |
| ABBK | 3.50-18 |
| ABTN | 3.50-19 |
| ABBM | 3.50-6 |
| ABTP | 3.75-19 |
| AAKN | 30.00-33 |
| ABTQ | 30.00-51 |
| AAAV | 325/85-R16 |
| ABTR | 32X4X28 |
| ABTS | 33.25-35 |
| AAVG | 33.5-33 |
| AAVH | 33.5-39 |
| ABGW | 36.00-41 |
| AAVK | 36.00-51 |
| ABTT | 36X10X30 |
| ABTW | 36X12X30 |
| ABTX | 36X14X30 |
| ABTY | 36X16X30 |
| ABTZ | 36X8X30 |
| ABWA | 36X9X30 |
| ABWB | 37.25-35 |
| ABBT | 37.5-33 |
| ABWC | 37.5-39 |
| ABWD | 37.5-51 |
| AABU | 395/85-R20 |
| AABR | 4.00-12 |
| AACT | 4.00-15 |
| AAEW | 4.00-18 |
| AAFF | 4.00-19 |
| ABBY | 4.00-36 |
| ABWE | 4.00-4 |
| ABWF | 4.00-6 |
| AABB | 4.00-8 |
| AABE | 4.00-9 |
| ABWG | 4.10-4 |
| ABWH | 4.10-5 |
| ABWJ | 4.10-6 |
| ABWK | 4.25-18 |
| AAEX | 4.50-18 |
| AAVL | 4.75-7.75 |
| ABWL | 4.80-8 |
| AACW | 5.00-15 |
| AADR | 5.00-16 |
| ABCK | 5.00X8 |
| AAVQ | 5.10-16 |
| ABCP | 5.50-15 |
| AADS | 5.50-16 |
| AAVT | 5.50-20 |
| ABCQ | 5.50-4 |
| ABWM | 5.5L-15 |
| ACAW | 5.60-13 |
| ACAX | 5.60-15 |
| ABWN | 5.70-8 |
| ABGX | 5.90-13 |
| AACX | 5.90-15 |
| ABWP | 5-1/2X4-1/2 |
| ABWQ | 5-1/2X5 |
| ABCR | 5-12 |
| ABCS | 5-8 |
| AALG | 5X1.75 |
| ABWR | 5X1-7/8 |
| AABW | 6.00-12 |
| AACB | 6.00-13 |
| AADT | 6.00-16 |
| ABCT | 6.00-17 |
| AAVX | 6.00-20 |
| AAVY | 6.00-21 |
| AAAP | 6.00-6 |
| AAQA | 6.00-9 |
| AAWB | 6.2-30 |
| AACY | 6.40-15 |
| AACF | 6.45-14 |
| AABJ | 6.50-10 |
| AACC | 6.50-13 |
| AACZ | 6.50-15 |
| AADW | 6.50-16 |
| AAEY | 6.50-18 |
| AAFQ | 6.50-20 |
| ABDC | 6.50-36 |
| AANL | 6.50-8 |
| ABWS | 6.60-9 |
| ACAY | 6.70-13 |
| AADA | 6.70-15 |
| ABDE | 6.70-16 |
| AADB | 6.85-15 |
| ABWT | 6.90-9 |
| AACG | 6.95-14 |
| ABWW | 6-1/2X4 |
| ABWX | 6-1/2X4-1/2 |
| ABWY | 6-1/2X5 |
| ABDG | 6-12 |
| ABDH | 6-16 |
| ABWZ | 6X1-3/4 |
| AALH | 6X2.00 |
| ABXA | 6X2-1/2 |
| ABXB | 6X2-1/4 |
| ABXC | 6X2-7/8 |
| ABXD | 6X4-1/2 |
| AABY | 7.00-12 |
| AACD | 7.00-13 |
| AAWK | 7.00-14 |
| AADC | 7.00-15 |
| AADX | 7.00-16 |
| AAEN | 7.00-17 |
| AAEZ | 7.00-18 |
| AAFR | 7.00-20 |
| AAGY | 7.00-24 |
| AADD | 7.10-15 |
| ADWQ | 7.17-5 |
| ABXE | 7.2-24 |
| ADWP | 7.22-5 |
| ACAZ | 7.25-13 |
| AACH | 7.35-14 |
| AADE | 7.35-15 |
| AABK | 7.50-10 |
| ACBA | 7.50-13 |
| AADF | 7.50-15 |
| AADY | 7.50-16 |
| AAEP | 7.50-17 |
| AAFA | 7.50-18 |
| AAFS | 7.50-20 |
| AAGZ | 7.50-24 |
| ABXF | 7.50L-15 |
| AAWQ | 7.5L-15 |
| AADG | 7.60-15 |
| AACL | 7.75-14 |
| AADH | 7.75-15 |
| ABDN | 7-14.5 |
| ABDQ | 7-16 |
| AAWV | 7-17.5 |
| ABDR | 7-22.5 |
| ABXG | 7X2-1/2 |
| ABXH | 7X5-1/2 |
| ABXJ | 8.00-15 |
| AAWX | 8.00-16.5 |
| AAWY | 8.00-6 |
| AADJ | 8.15-15 |
| ADWR | 8.17-5 |
| ADWS | 8.19-5 |
| AADK | 8.20-15 |
| ADWT | 8.22-5 |
| AACM | 8.25-14 |
| AADL | 8.25-15 |
| AADZ | 8.25-16 |
| AAEQ | 8.25-17 |
| AAFB | 8.25-18 |
| AAFT | 8.25-20 |
| AAHA | 8.25-24 |
| AANQ | 8.50-10 |
| AACN | 8.55-14 |
| ABEA | 8.55-15 |
| AAXA | 8.5L-14 |
| ABXK | 8.5L-16 |
| AAXB | 8.75-16.5 |
| AACP | 8.85-14 |
| AADN | 8.85-15 |
| AADP | 8.90-15 |
| ABXQ | 8-1/2X4X4 |
| ABEB | 8-14.5 |
| ABEC | 8-16 |
| ABED | 8-17.5 |
| ABEE | 8-19.5 |
| ABEF | 8-22.5 |
| ABXL | 8X2 |
| AALJ | 8X2.00 |
| ABXM | 8X2.50 |
| ABXN | 8X2-1/2 |
| ABXP | 8X4-1/2 |
| AABL | 9.00-10 |
| AADQ | 9.00-15 |
| AAEA | 9.00-16 |
| AAFC | 9.00-18 |
| AAFW | 9.00-20 |
| AAXE | 9.00-22 |
| AAHC | 9.00-24 |
| ABEJ | 9.00-36 |
| ABEP | 9.15-15 |
| ADWW | 9.22-5 |
| ABEQ | 9.50-14 |
| AAXL | 9.50-16.5 |
| ABXY | 9.50-20 |
| AAXG | 9.5-16 |
| ABXR | 9.5-24 |
| ABXS | 9.5-36 |
| ABXT | 9.5-38 |
| ABXW | 9.5-42 |
| AAXJ | 9.5L-14 |
| AAXK | 9.5L-15 |
| ABXX | 9.5L-16 |
| ABYF | 9-1/2X5X5 |
| ABFC | 9-14.5 |
| ABFD | 9-19.5 |
| ABFE | 9-22.5 |
| ABXZ | 9X2 |
| ABYA | 9X2-1/2 |
| ABYB | 9X3 |
| ABYC | 9X4 |
| ABYD | 9X5 |
| ABYE | 9X5X5 |
| AANR | 9X6 |
| ABJL | A70-13 |
| ABFX | A78-13 |
| ADWC | AR70-13 |
| ABJK | AR78-13 |
| ABJQ | B78-13 |
| ABFY | B78-14 |
| ABJM | BR78-13 |
| ABJN | BR78-14 |
| ABJP | BR78-15 |
| ABJZ | C70-14 |
| ABKA | C70-15 |
| ABKB | C78-13 |
| ABFZ | C78-14 |
| ABGA | C78-15 |
| ABJR | CR70-14 |
| ABJS | CR70-15 |
| ABJT | CR78-13 |
| ABJW | CR78-14 |
| ABJX | CR78-15 |
| ABKH | D70-13 |
| ABKJ | D70-14 |
| ABKK | D70-15 |
| ABGB | D78-14 |
| ABGC | D78-15 |
| ABKC | DR70-14 |
| ABKD | DR70-15 |
| ABKE | DR78-13 |
| ABKF | DR78-14 |
| ABKG | DR78-15 |
| ACAS | E70-14 |
| ADWG | E70-15 |
| ABGD | E78-14 |
| ABGE | E78-15 |
| ADWE | ER70-14 |
| ADWH | ER70-15 |
| ADWF | ER78-15 |
| ABKQ | F70-14 |
| ABKR | F70-15 |
| ABGF | F78-14 |
| ABGG | F78-15 |
| ABKL | FR70-14 |
| ABKM | FR70-15 |
| ABKN | FR78-14 |
| ABKP | FR78-15 |
| ADWL | G70-15 |
| ABGH | G78-14 |
| ABGJ | G78-15 |
| ADWN | GR70-15 |
| ADWK | GR78-14 |
| ADWJ | GR78-15 |
| ABKX | H70-14 |
| ABKY | H70-15 |
| ABGK | H78-14 |
| ABGL | H78-15 |
| ADWM | HR70-15 |
| ABKT | HR78-14 |
| ABKW | HR78-15 |
| ABLB | J70-14 |
| ABLC | J70-15 |
| ABGQ | J78-14 |
| ABGM | J78-15 |
| ABKZ | JR78-14 |
| ABLA | JR78-15 |
| ABLF | L70-14 |
| ABLG | L70-15 |
| ABGN | L78-15 |
| ABLH | L84-15 |
| ABLD | LR78-15 |
| ABLK | M78-15 |
| ABLJ | MM90-19 |
| ABLL | N78-15 |
| AEPK | P235/75-15 |
BYHSDCROSS CHAIN CASEHARDENING INDICATOR
INDICATES WHETHER OR NOT A FERROUS ALLOY CROSS CHAIN HAS BEEN SUBJECTED TO A PROCESS WHEREBY THE OUTER PORTION IS MADE SUBSTANTIALLY HARDER THAN THE INNER PORTION OR CORE.
Enter the applicable reply code from the table below
(BYHSDA)
| Table 1 |
| Reply Code (AA70) | Reply |
| A | CASEHARDENED |
| B | NOT CASEHARDENED |
BYHNACROSS CHAIN LINK QUANTITY
THE NUMBER OF CROSS CHAIN LINKS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BYHNA10*)
BYHPDCROSS CHAIN TYPE
INDICATES THE TYPE OF CROSS CHAIN PROVIDED.
Enter the applicable reply code from the table below
(BYHPDBQ)
| Table 1 |
| Reply Code (AC71) | Reply |
| A | ANY ACCEPTABLE |
| BE | BAR REINFORCED TWIST |
| BF | REGULAR TWIST |
| BQ | REGULAR TWIST, SWIVEL HOOK |
| BG | REINFORCED FLAT |
| BT | THREE SIDED |
| BW | X-LINKED |
BYHQJCROSS CHAIN LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE CROSS CHAIN,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYHQJAC2.0*;BYHQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYHRACROSS CHAIN QUANTITY
THE NUMBER OF CROSS CHAINS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BYHRA10*)
BYHTJCROSS CHAIN LINK WIRE SIZE
DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE CROSS CHAIN LINK WIRE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYHTJAB2.0*;BYHTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) DFB WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (BYHX and BYHY)
IF STYLE/REPLY CODE(s) DFC WERE ENTERED FOR MRC APGF, YOU MUST ANSWER MRC (BYHX and BYHY and BYHZ and BYJB)
APGFDDESIGN TYPE
INDICATES THE DESIGN TYPE OF THE ITEM.
Enter the applicable reply code from the table below
(APGFDDFC)
| Table 1 |
| Reply Code (AK54) | Reply |
| DFC | THREE SIDE |
| DFB | TWO SIDE |
BYHX*JOUTER SIDE CHAIN LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE OUTER SIDE CHAIN,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYHXJAC2.0*;BYHXJAC2.0$JAC2.0*;BYHXJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYHY*AOUTER SIDE CHAIN LINK QUANTITY
THE NUMBER OF OUTER SIDE CHAIN LINKS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BYHYA10*)
BYHZ*JINNER SIDE CHAIN LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE INNER SIDE CHAIN,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYHZJAB2.0*;BYHZJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYJB*AINNER SIDE CHAIN LINK QUANTITY
THE NUMBER OF INNER SIDE CHAIN LINKS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BYJBA10*)
BYJCGCROSS CHAIN SPACING
THE SPACING OF THE CROSS CHAINS.
Enter clear text.
(BYJCGCLEARTEXT)
BYJDJSIDE CHAIN WIRE SIZE
DESIGNATES THE SIZE OF THE RELATIVE OR PROPORTIONATE DIMENSIONS OF THE SIDE CHAIN WIRE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYJDJAC2.0*;BYJDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCDZ)
| Table 1 |
| Reply Code (AN47) | Reply |
| CDZ | BINDING CHAIN |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
DAAH*DITEM TYPE CATEGORY
THE CATEGORY THAT IDENTIFIES THE TYPE OF ITEM.
Enter the applicable reply code from the table below
(DAAHDAC*;DAAHDAA$DAF*;DAAHDAA$$DAF*)
| Table 1 |
| Reply Code (TC01) | Reply |
| AA | ACCESSORY |
| AD | INNER RIM |
| AC | ONE PIECE RIM |
| AE | OUTER RIM |
| AB | TIRE |
| AF | WHEEL ASSEMBLY |
DAAJ*DACCESSORY TYPE
THE CATEGORY THAT IDENTIFIES THE TYPE OF ACCESSORY.
Enter the applicable reply code from the table below
(DAAJDAL*;DAAJDAK$DAF*;DAAJDAK$$DAF*)
| Table 1 |
| Reply Code (AC47) | Reply |
| AK | ADAPTER |
| AD | CAP |
| AE | CHAIN |
| AB | EQUIPMENT |
| AJ | FLAP |
| AG | INNER TUBE |
| AM | RUN FLAT INSERT |
| AF | STRAP |
| AL | TIRE GAGE |
| AA | TOOL |
| AH | VALVE |
| AC | WHEEL WEIGHT |
DAAG*ATIRE VALVE DESIGNATION
THE SIZE DESIGNATION OF THE TIRE VALVE.
Enter the alpha-numeric reply with a minimum of one character.
(DAAGAJ5)
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ222*;HZRDDHAZ285$$DHAZ030*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ222 | IRON |
| HAZ092 | MAGNESIUM |
| HAZ030 | MAGNESIUM ALLOY |
| HAZ285 | PLASTIC |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3HWADZSC000*;MATT3HWADZSC000$DSTA000*;MATT3HWADZSC000$$DSTA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HWA | CROSS CHAIN |
| 3HWB | SIDE CHAIN |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALB000 | ALUMINUM ALLOY |
| STA000 | STEEL |
| ZSC000 | STEEL ALLOY |
SFTTDSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(SFTT3AEEDZNA000*;SFTT3AEEDZNA000$DZNA000*;SFTT3AEEDZNA000$$DZNA000*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| 3HWA | CROSS CHAIN |
| 3HWB | SIDE CHAIN |
| Table 2 |
| Reply Code (SF01) | Reply |
| ZNA000 | ZINC |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information