A pulley with one or more grooved faces or rims of the same diameter. For pulleys encased in a shell or frame, see BLOCK, TACKLE.For items specifically designed for aviation, see PULLEY(1), GROOVE, AVIATION.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED08109*)
BXSJDLIGHTENING HOLE
AN INDICATION OF WHETHER A LIGHTENING HOLE/S/ IS/ARE INCLUDED. PLEASE USE MRC ABFF FOR NIINS THAT WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(BXSJDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
BXSKDINTEGRAL COOLING VANE
AN INDICATION OF WHETHER OR NOT AN INTEGRAL COOLING VANE(S) IS INCLUDED.
Enter the applicable reply code from the table below
(BXSKDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BSYG, YOU MUST ANSWER MRC (BYFC and BYFD)
BSYGDSPLIT HUB FEATURE
AN INDICATION OF WHETHER OR NOT A SPLIT HUB FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(BSYGDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
BYFC*DHUB SPLIT LOCATION
INDICATES THE LOCATION OF THE SPLIT(S) ON THE HUB.
Enter the applicable reply code from the table below
(BYFCDCBQ*;BYFCDCBP$DCBP*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| CBP | THROUGH BOTH WALLS |
| CBQ | THROUGH ONE WALL |
BYFD*ACLAMPING BOLT QUANTITY
THE NUMBER OF CLAMPING BOLTS PROVIDED.
Enter the numeric reply with a minimum of one digit.
(BYFDA10*)
IF STYLE/REPLY CODE(s) A1 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AQPL and ABHE)
IF STYLE/REPLY CODE(s) A2, A3, A6, A7, A10, A11, A14, A15, A16, A17, A19, A20, A21, A22, A23, A25 OR A26 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ABHE and AQPL and BYZD and BYZF)
IF STYLE/REPLY CODE(s) A4 OR A9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHE and AQPL and BYZF)
IF STYLE/REPLY CODE(s) A5, A12, A24 OR A28 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHE and AQPL and BYZD and BYZF)
IF STYLE/REPLY CODE(s) A8 OR A27 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHE and AQPL and BYZD)
IF STYLE/REPLY CODE(s) A13 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHE and ABHP and ABKU and AHTC and AQPL and BYZD and BYZF and BYZG)
IF STYLE/REPLY CODE(s) A18 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHE and ABHP and AQPL and BYZF)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLA18)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAB1479 | A1 | PLAIN |
| AAB1488 | A10 | WEBBED OR SPOKED |
| AAB1489 | A11 | WEBBED OR SPOKED |
| AAB1490 | A12 | WEBBED OR SPOKED |
| AAB1491 | A13 | PLAIN |
| AAB1492 | A14 | WEBBED OR SPOKED |
| AAB1493 | A15 | WEBBED OR SPOKED |
| AAB1494 | A16 | WEBBED OR SPOKED |
| AAB1495 | A17 | WEBBED OR SPOKED |
| AAB1496 | A18 | WEBBED OR SPOKED |
| AAB1497 | A19 | WEBBED OR SPOKED |
| AAB1480 | A2 | PLAIN |
| AAB1498 | A20 | WEBBED OR SPOKED |
| AAB1499 | A21 | WEBBED OR SPOKED |
| AAB1500 | A22 | WEBBED OR SPOKED |
| AAB1501 | A23 | WEBBED OR SPOKED |
| AAB1502 | A24 | WEBBED OR SPOKED |
| AAB1503 | A25 | WEBBED OR SPOKED |
| AAB1504 | A26 | WEBBED OR SPOKED |
| AAB1505 | A27 | WEBBED OR SPOKED |
| AAB1506 | A28 | WEBBED OR SPOKED |
| AAB1481 | A3 | PLAIN |
| AAB1482 | A4 | WEBBED OR SPOKED |
| AAB1483 | A5 | WEBBED OR SPOKED |
| AAB1484 | A6 | WEBBED OR SPOKED |
| AAB1485 | A7 | WEBBED OR SPOKED |
| AAB1486 | A8 | WEBBED OR SPOKED |
| AAB1487 | A9 | WEBBED OR SPOKED |
ABHE*JOUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN ITEM,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHEJAB2.0*;ABHEJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKU*JFLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A FLANGE,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKUJAC2.0*;ABKUJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHTC*JFLANGE OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHTCJAA2.0*;AHTCJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AQPL*JFACE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FACE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AQPLJAB2.0*;AQPLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYZD*JHUB END OUTSIDE DIAMETER AND LOCATION
NONE. PLEASE USE MRC ALNC WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZDJAAAHH2.0*;BYZDJAAAHH2.0$$JAAAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
BYZF*JDISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION
NONE. PLEASE USE MRC ASYR WITH USE OF ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZFJAAAHH2.0*;BYZFJAAAHH2.0$$JAAAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
BYZG*JDISTANCE FROM PILOT END TO FLANGE FACE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZGJAC2.0*;BYZGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) ADF OR ADG WERE ENTERED FOR MRC ARJD, YOU MUST ANSWER MRC (BXSH)
ARJDDDESIGN FORM
THE PHYSICAL CONFIGURATION OF THE ITEM.
Enter the applicable reply code from the table below
(ARJDDAAM*;ARJDDADF$DADG*;ARJDDADF$$DADG*)
| Table 1 |
| Reply Code (AL52) | Reply |
| AHG | GROOVED |
| AAM | PLAIN |
| ADF | SPOKED |
| ADG | WEBBED |
BXSH*DWEB/SPOKE RELATIONSHIP TO FACE CENTERLINE
AN INDICATION OF THE RELATIONSHIP BETWEEN THE WEBBING OR SPOKES AND THE CENTERLINE OF THE FACE.
Enter the applicable reply code from the table below
(BXSHDSW)
| Table 1 |
| Reply Code (AE98) | Reply |
| A | ANY ACCEPTABLE |
| SW | NOT OFFSET |
| TK | OFFSET |
IF STYLE/REPLY CODE(s) PD WERE ENTERED FOR MRC BXSM, YOU MUST ANSWER MRC (AXHQ and ABGA and ABGF and AGWA)
IF STYLE/REPLY CODE(s) ZK WERE ENTERED FOR MRC BXSM, YOU MUST ANSWER MRC (AXHQ and ABGA and ABGF and AGGS)
BXSMDGROOVE SHAPE
THE PHYSICAL CONFIGURATION OF THE GROOVE.
Enter the applicable reply code from the table below
(BXSMDPD*;BXSMDZK$DAND*)
| Table 1 |
| Reply Code (AD07) | Reply |
| ABN | CHANNEL |
| AND | RECTANGULAR |
| PD | U |
| ZK | V |
AXHQ*AGROOVE QUANTITY
THE NUMBER OF GROOVES PROVIDED.
Enter the numeric reply with a minimum of one digit.
(AXHQA10*)
ABGA*JGROOVE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGAJAA2.0*;ABGAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGF*JGROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGFJAC2.0*;ABGFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGWA*JGROOVE RADIUS
A MEASUREMENT OF A LINE SEGMENT EXTENDING FROM THE CENTER OF A GROOVE TO THE INSIDE SURFACE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGWAJAC2.0*;AGWAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGGS*BV GROOVE ANGLE IN DEG
THE ANGLE OF THE V GROOVE,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AGGSB2.0)
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BYDS, YOU MUST ANSWER MRC (AWJQ and ASBP and AXND)
BYDSDBORE FEATURE
AN INDICATION OF WHETHER OR NOT A BORE FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(BYDSDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AWJQ, YOU MUST ANSWER MRC (BYDT and BDDY)
AWJQ*DBEARINGS
AN INDICATION OF WHETHER BEARINGS ARE INCLUDED. PLEASE USE MRC ABFF FOR NIINS THAT WERE ANSWERED WITH "INCLUDED" IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(AWJQDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) AF WERE ENTERED FOR MRC BYDT, YOU MUST ANSWER MRC (BYDW)
BYDT*DBEARING TYPE
INDICATES THE TYPE OF BEARING PROVIDED.
Enter the applicable reply code from the table below
(BYDTDBH*;BYDTDAK$DAH*;BYDTDAK$$DAH*)
| Table 1 |
| Reply Code (AH96) | Reply |
| AD | ANNULAR ROLLER |
| A | ANY ACCEPTABLE |
| AE | BALL |
| AF | BEARING ROLLER |
| BH | BUSHING |
| AG | FLANGED |
| AH | NEEDLE ROLLER |
| AJ | ROLLER |
| AK | SLEEVE |
BYDW*JSHAFT SIZE FOR WHICH DESIGNED
DESIGNATES THE SIZE OF THE SHAFT FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYDWJAC2.0*;BYDWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BDDY*ABEARING QUANTITY
THE NUMBER OF BEARINGS PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(BDDYA10*)
IF STYLE/REPLY CODE(s) AK WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ABSA and AXFG and BDTX and AAUJ and ABSC and AXFH)
IF STYLE/REPLY CODE(s) AB WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ABXV and ADGE and BSGG)
IF STYLE/REPLY CODE(s) AM WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ABSA and AAUJ and ABSC and AXFH)
IF STYLE/REPLY CODE(s) AC WERE ENTERED FOR MRC ASBP, YOU MUST ANSWER MRC (ADGE and ANAL and ANAM and BSGG)
ASBP*DBORE TYPE
INDICATES THE TYPE OF BORE USED ON THE ITEM.
Enter the applicable reply code from the table below
(ASBPDAK*;ASBPDAC$DAJ*)
| Table 1 |
| Reply Code (AL72) | Reply |
| AK | INVOLUTE SPLINE |
| AJ | SPLINED |
| AB | STRAIGHT |
| AM | STRAIGHT SPLINE |
| AC | TAPERED |
ABSA*ASPLINE QUANTITY
THE NUMBER OF SPLINES ON OR IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ABSAA10*)
AXFG*BSPLINE PRESSURE ANGLE IN DEG
THE PRESSURE ANGLE OF THE SPLINE,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AXFGB2.0)
BDTX*JSPLINE PITCH DIAMETER
A MEASUREMENT OF THE SPLINE PITCH DIAMETER.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BDTXJAA2.0*;BDTXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAUJ*JSPLINE MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAUJJAB2.0*;AAUJJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABSC*JSPLINE MINOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST CROSS SECTION OF A SPLINE,AND TERMINATES AT THE CIRCUMFERENCE. PLEASE USE MRC AAUH IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABSCJAC2.0*;ABSCJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AXFH*JSPLINE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A SPLINE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AXFHJAC2.0*;AXFHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXV*JBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXVJAB2.0*;ABXVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADGE*JBORE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A BORE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADGEJAC2.0*;ADGEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAL*JTAPER BORE MAJOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE LARGEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANALJAB2.0*;ANALJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ANAM*JTAPER BORE MINOR DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE SMALLEST PORTION OF A TAPERED BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ANAMJAC2.0*;ANAMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC AXND, YOU MUST ANSWER MRC (BDYS and AAWY and AAWZ)
AXND*DCOUNTERBORE FEATURE
AN INDICATION OF WHETHER OR NOT A COUNTERBORE FEATURE IS INCLUDED.
Enter the applicable reply code from the table below
(AXNDDC)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
BDYS*DCOUNTERBORE LOCATION
INDICATES THE LOCATION OF THE COUNTERBORE ON THE ITEM.
Enter the applicable reply code from the table below
(BDYSDBBZ*;BDYSDAHH$DBCA*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
| AXG | COUNTERBORE |
AAWY*JCOUNTERBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A COUNTERBORED PORTION OF A HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWYJAC2.0*;AAWYJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAWZ*JCOUNTERBORE DEPTH
THE DEPTH OF THE PROCESS USED TO ENLARGE PART OF A HOLE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAWZJAA2.0*;AAWZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) B WERE ENTERED FOR MRC BSGG, YOU MUST ANSWER MRC (BSGK)
BSGG*DKEYING FACILITY
AN INDICATION OF WHETHER OR NOT A KEYING FACILITY IS INCLUDED. PLEASE USE MRC ABFF FOR NIINS WERE ANSWERD WITH "INCLUDED" IN PLACE OF THIS CANCELED MRC.
Enter the applicable reply code from the table below
(BSGGDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
IF STYLE/REPLY CODE(s) BZT WERE ENTERED FOR MRC BSGK, YOU MUST ANSWER MRC (NMBR and ABRR and AEVF)
BSGK*DKEYING FACILITY TYPE
INDICATES THE TYPE OF KEYING FACILITY PROVIDED.
Enter the applicable reply code from the table below
(BSGKDBZT*;BSGKDCDS$DBZS*)
| Table 1 |
| Reply Code (AK54) | Reply |
| BZS | INTEGRAL KEY |
| BZT | KEYWAY |
| CDS | TAPERED KEYWAY |
ABRR*JKEYWAY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEYWAY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABRRJAC2.0*;ABRRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEVF*JDISTANCE FROM CENTER OF BORE TO BOTTOM OF KEYWAY
THE DISTANCE FROM THE CENTER OF THE BORE TO THE BOTTOM OF THE KEYWAY(S).
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVFJAC2.0*;AEVFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
NMBR*AQUANTITY
A NUMERIC VALUE WHICH REPRESENTS A POSITIVE WHOLE VALUE WITHOUT REGARD TO ANY UNIT OF MEASURE.
Enter the numeric reply with a minimum of one digit.
(NMBRA10*)
ABSF*JKEY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A KEY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABSFJAA2.0*;ABSFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEVD*JDISTANCE FROM CENTER OF BORE TO TOP OF KEY
THE DISTANCE FROM THE CENTER OF THE BORE TO THE TOP OF THE KEY/S/.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVDJAB2.0*;AEVDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEVG*BKEY SPACING IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEVGB2.0)
BYDY*DKEYING FACILITY LARGEST DIMENSION LOCATION
INDICATES THE LOCATION OF THE LARGEST DIMENSION OF THE KEYING FACILITY.
Enter the applicable reply code from the table below
(BYDYDBBZ*;BYDYDBCA$DBCA*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
AEVJ*BKEYWAY SPACING IN DEG
A MEASUREMENT OF THE AMOUNT OF TURNING NECESSARY TO BRING ONE KEYWAY INTO COINCIDENCE WITH ANOTHER,EXPRESSED IN DEGREES.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AEVJB2.0)
BYDZ*DPROTRUDING HUB CHARACTERISTIC
AN INDICATION OF THE CHARACTERISTIC OF THE PROTRUDING HUB.
Enter the applicable reply code from the table below
(BYDZDAAJ*;BYDZDAAH$DAAG*)
| Table 1 |
| Reply Code (AJ88) | Reply |
| AAG | GROOVED |
| AAJ | PLAIN |
| AAH | STEPPED |
BYZL*JFIRST STEP FACE LARGEST DIAMETER AND LOCATION
THE LARGEST DIAMETER AND LOCATION OF THE FIRST STEP FACE. PLEASE USE MRC ABPR WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZLJAABBZ2.0*;BYZLJAABBZ2.0$$JAABBZ2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
BYZM*JSECOND STEP FACE LARGEST DIAMETER AND LOCATION
THE LARGEST DIAMETER AND LOCATION OF THE SECOND STEP FACE. PLEASE USE MRC ABPT WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZMJAABBZ2.0*;BYZMJAABBZ2.0$$JAABBZ2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZN*JFIRST STEP LENGTH AND LOCATION
THE LENGTH AND LOCATION OF THE FIRST STEP. PLEASE USE MRC ABPS WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZNJAAAHH2.0*;BYZNJAAAHH2.0$$JAAAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZP*JSECOND STEP LENGTH AND LOCATION
THE LENGTH AND LOCATION OF THE SECOND STEP. PLEASE USE MRC ABPU WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZPJABAHH2.0*;BYZPJABAHH2.0$$JABAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZQ*JTHIRD STEP FACE LARGEST DIAMETER AND LOCATION
THE LARGEST DIAMETER AND LOCATION OF THE THIRD STEP FACE.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZQJABBBZ2.0*;BYZQJABBBZ2.0$$JABBBZ2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZR*JFIRST END GROOVE DIAMETER AND LOCATION
THE DIAMETER AND LOCATION OF THE FIRST END GROOVE. PLEASE USE MRC AAHH WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZRJACBCA2.0*;BYZRJACBCA2.0$$JACBCA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZS*JFIRST END GROOVE WIDTH AND LOCATION
THE WIDTH AND LOCATION OF THE FIRST END GROOVE. PLEASE USE MRC AAHG WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZSJACBBZ2.0*;BYZSJACBBZ2.0$$JACBBZ2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZX*JTHIRD STEP LENGTH AND LOCATION
THE LENGTH AND LOCATION OF THE THIRD STEP.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZXJABAHH2.0*;BYZXJABAHH2.0$$JABAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BYZY*JFOURTH STEP LENGTH AND LOCATION
THE LENGTH AND LOCATION OF THE FOURTH STEP.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BYZYJAAAHH2.0*;BYZYJAAAHH2.0$$JAAAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
BZBC*JSECOND END GROOVE DIAMETER AND LOCATION
THE DIAMETER AND LOCATION OF THE SECOND END GROOVE.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(BZBCJACAHH2.0*;BZBCJACAHH2.0$$JACAHH2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CLYR*JHUB END OUTSIDE DIAMETER AND LOCATION
THE OUTSIDE DIAMETER AND LOCATION OF THE HUB END. PLEASE USE MRC ALNC WITH ISAC TBL 0368 IN PLACE OF THIS CANCELED MRC.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYRJAABCA2.0*;CLYRJAABCA2.0$$JAABCA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CLYS*JDISTANCE FROM OUTSIDE FLANGE/RIM TO HUB END AND LOCATION
THE DISTANCE FROM THE OUTSIDE FLANGE OR RIM TO THE HUB END, AND ITS LOCATION.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CLYSJAABCA2.0*;CLYSJAABCA2.0$$JAABCA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
| Table 3 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
IF YOU ANSWER MRC BSNP, YOU MUST ANSWER MRC (BYFF)
IF STYLE/REPLY CODE(s) AHF WERE ENTERED FOR MRC BSNP, YOU MUST ANSWER MRC (AHYF and ABUJ and BFYT) or (AHYF and BFYT and THSD)
IF STYLE/REPLY CODE(s) BFY WERE ENTERED FOR MRC BSNP, YOU MUST ANSWER MRC (AHYF and AGGP and BFYT) or (AHYF and BYFG and BFYT)
BSNP*DSECURING METHOD
THE MEANS BY WHICH THE ITEM IS SECURED.
Enter the applicable reply code from the table below
(BSNPDADC*;BSNPDAVV$DAAG*;BSNPDAVV$$DAAG*)
| Table 1 |
| Reply Code (AM39) | Reply |
| A | ANY ACCEPTABLE |
| BFT | AXIALLY LOCATED SCREW |
| BFW | BOLTED THROUGH BORE |
| ABD | BUSHING |
| ABH | CLAMP |
| AEM | COMPRESSION |
| BFX | COTTER PIN |
| BFY | DRILLED HOLE |
| BSD | HUB |
| BFG | KEY |
| BFD | KEYWAY |
| AVU | MACHINED RECESS |
| BFZ | MOUNTED BETWEEN BRACKETS |
| BGA | NUT |
| AAD | PIN |
| ADC | PRESS FIT |
| BGB | PRESS FIT BEARING |
| AVV | PULLEY SHAFT W/ HEX CAP NUT |
| AHK | RETAINING PLATE |
| BGC | RETAINING RING |
| AAG | RIVET |
| AAF | SETSCREW |
| ABX | SHAFT |
| BGD | SLOTTED |
| AVX | SLOTTED HUB CLAMP |
| AHL | SNAP RING |
| BGE | SOLDERED |
| ABZ | SPACER |
| AVW | SPINDLE ASSEMBLY |
| BGF | SPLIT-TAPERED BUSHING |
| BGG | STAKED |
| AAE | STUD |
| AVY | TAPER LOCK |
| BGH | TAPERED-LOCK BUSHING |
| AHF | THREADED HOLE |
| AKK | WELDED |
BFYT*GHOLE LOCATION
INDICATES THE LOCATION OF THE HOLE ON THE ITEM.
Enter clear text.
(BFYTGCLEARTEXT)
BYFF*DSECURING LOCATION
INDICATES THE LOCATION FOR SECURING THE ITEM.
Enter the applicable reply code from the table below
(BYFFDDKR*;BYFFDAUX$DBCA*;BYFFDAUX$$DBCA*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
| AHH | BOTH ENDS |
| DKR | KEYWAY TOP |
| AUX | OPPOSITE HUB END |
| ADM | PULLEY SURFACE |
| AUW | TOP OF HUB |
| APJ | WEB |
AHYF*ASECURING HOLE QUANTITY
THE NUMBER OF HOLES PROVIDED FOR SECURING THE ITEM IN A FIXED POSITION.
Enter the numeric reply with a minimum of one digit.
(AHYFA10*)
ABUJ*ATHREAD SIZE
DESIGNATES THE THREAD DIAMETER AND NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the alpha-numeric reply with a minimum of one character.
(ABUJAT7)
AGGP*JDRILLED HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A DRILLED HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGGPJAC2.0*;AGGPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
BYFG*ATAPERED HOLE SIZE
DESIGNATES THE STANDARD SIZE DESIGNATION OF THE TAPERED HOLE.
Enter the alpha-numeric reply with a minimum of one character.
(BYFGAF6)
IF YOU ANSWER MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJF and CQQR) or (CQJX and AAJF and AAJE)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(THSDDSJ)
| Table 1 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| SJ | SI |
| SK | SI-M |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(CQQRB2.0)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(AAJFDAAG)
| Table 1 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAB2.0*;ABKGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(CTTCJNTETEXT1234*)
| Table 1 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
AWPJ*DTAPER MAJOR DIAMETER LOCATION
INDICATES THE LOCATION OF THE TAPER MAJOR DIAMETER.
Enter the applicable reply code from the table below
(AWPJDBBZ*;AWPJDBCA$DBBZ*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
BYDX*DTAPERED SPLINE LARGEST MINOR DIAMETER LOCATION
INDICATES THE LOCATION OF THE TAPERED SPLINE LARGEST MINOR DIAMETER.
Enter the applicable reply code from the table below
(BYDXDBCA*;BYDXDBBZ$DBBZ*)
| Table 1 |
| Reply Code (AJ91) | Reply |
| BBZ | AA END |
| BCA | BB END |
BXSN*ASTANDARD V-BELT SECTION DESIGNATION FOR WHICH DESIGNED
THE ALPHA AND/OR NUMERIC SECTION DESIGNATION OF THE STANDARD V-BELT FOR WHICH DESIGNED.
Enter the alpha-numeric reply with a minimum of one character.
(BXSNAI4)
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPSA000*;SFTTDAAA002$DCMB000*;SFTTDAAA002$$DCMB000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| AAA002 | CHEMICAL |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CRB000 | CHROMIUM OXIDE |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| ENE000 | ENAMEL GLOSS |
| ENF000 | ENAMEL SEMIGLOSS |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PCS000 | PLASTIC EPOXY |
| PRD000 | PRIMER EPOXY-POLYAMIDE |
| MSJ000 | RUSTPROOF |
| VAA000 | VARNISH |
| ZNA000 | ZINC |
| AAAAAB | ZINC NICKEL |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
AGJS*JPITCH DIAMETER
A MEASUREMENT INDICATING THE DIAMETER-PITCH PER SPECIFIC MEASUREMENT SCALE OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGJSJAC2.0*;AGJSJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAVL*JPILOT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THAT PORTION USED TO GUIDE THE ITEM AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAVLJAA2.0*;AAVLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AKYN*GFURNISHED ITEMS AND QUANTITY
THE NAME AND NUMBER OF THOSE PARTS FURNISHED WITH THE ITEM OF SUPPLY THAT HAVE NOT BEEN SPECIFIED ELSEWHERE.
Enter clear text.
(AKYNGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
AWJN*JUNPACKAGED UNIT WEIGHT
THE MEASURED WEIGHT OF AN ITEM UNENCUMBERED BY PACKAGING OR PACKING MATERIAL. PLEASE USE MRC CTJS IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AWJNJAS2.0*)
| Table 1 |
| Reply Code (AG67) | Reply |
| AJ | KILOGRAMS |
| AS | POUNDS |
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDPDA000*;PRMTDIRA000$DAZA000*;PRMTDIRA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJIRA000R2.0*;PMWTJIRA000R2.0$$JIRA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(MATT3CYKDPCQ000*;MATT3CYKDPCQ000$DFE0044*;MATT3CYKDPCQ000$$DFE0044*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACU | FLANGE |
| 3AEE | OVERALL |
| 3CYK | HUB |
| 3CYY | RIM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2011 | ALUMINUM ALLOY 2011 |
| AL2014 | ALUMINUM ALLOY 2014 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0034 | ALUMINUM ALLOY 208.0 |
| AL0045 | ALUMINUM ALLOY 355.0 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL0043 | ALUMINUM ALLOY 520.0 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6062 | ALUMINUM ALLOY 6062 |
| AL7075 | ALUMINUM ALLOY 7075 |
| AL0002 | ALUMINUM ALLOY A356.0 |
| AL0030 | ALUMINUM ALLOY A413.0 |
| AL0060 | ALUMINUM ALLOY C355.0 |
| CSA000 | CELLULOSE |
| CUB000 | COPPER ALLOY |
| CU0074 | COPPER ALLOY 230 |
| CU0091 | COPPER ALLOY 360 |
| CU0099 | COPPER ALLOY 464 |
| CU0122 | COPPER ALLOY 630 |
| CU0197 | COPPER ALLOY 907 |
| CCA000 | COTTON |
| ZSF000 | FABRIC,REINFORCED PLASTIC |
| FBA000 | FIBER |
| GSB000 | GLASS FIBER |
| GFA000 | GRAPHITE |
| FEA000 | IRON |
| FE0019 | IRON ALLOY 660 |
| FEB000 | IRON CAST |
| FED000 | IRON CAST ALLOY |
| FE0117 | IRON CAST UNS F10006 |
| FE0044 | IRON CAST UNS F11401 |
| FE0045 | IRON CAST UNS F11701 |
| FE0046 | IRON CAST UNS F12101 |
| FE0052 | IRON CAST UNS F12401 |
| FE0047 | IRON CAST UNS F12801 |
| FE0048 | IRON CAST UNS F13101 |
| FE0049 | IRON CAST UNS F13501 |
| FE0050 | IRON CAST UNS F13801 |
| FE0051 | IRON CAST UNS F14101 |
| FE0038 | IRON CAST UNS F22200 |
| FE0039 | IRON CAST UNS F22400 |
| FE0053 | IRON CAST UNS F22830 |
| FE0065 | IRON CAST UNS F33100 |
| FEJ000 | IRON DUCTILE |
| FEC000 | IRON MALLEABLE |
| MGB000 | MAGNESIUM ALLOY |
| NLB000 | NICKEL ALLOY |
| NL0008 | NICKEL ALLOY 400 |
| PCA000 | PLASTIC |
| PCB000 | PLASTIC ACETAL |
| PCN000 | PLASTIC PHENOLIC |
| PCDS00 | PLASTIC PHENOLIC MOULDED |
| PCP000 | PLASTIC POLYAMIDE |
| PCQ000 | PLASTIC POLYCAPROLACTAM |
| PCR000 | PLASTIC POLYCARBONATE |
| PCW000 | PLASTIC POLYESTER |
| PCZ000 | PLASTIC POLYHEXAMETHYLENE ADIPAMIDE |
| PCAM00 | PLASTIC POLYHEXAMETHYLENE AMIDE |
| PCAA00 | PLASTIC POLYHEXAMETHYLENE SEBACAMIDE |
| PCAD00 | PLASTIC POLYSTYRENE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCDA01 | POLYAMIDE NYLON |
| RCE000 | RUBBER |
| RCB000 | RUBBER SYNTHETIC |
| STA000 | STEEL |
| ZSC000 | STEEL ALLOY |
| ST1006 | STEEL COMP 1006 |
| ST1008 | STEEL COMP 1008 |
| ST1010 | STEEL COMP 1010 |
| ST1015 | STEEL COMP 1015 |
| ST1018 | STEEL COMP 1018 |
| ST1020 | STEEL COMP 1020 |
| ST1022 | STEEL COMP 1022 |
| ST1035 | STEEL COMP 1035 |
| ST1040 | STEEL COMP 1040 |
| ST1042 | STEEL COMP 1042 |
| ST1045 | STEEL COMP 1045 |
| ST0530 | STEEL COMP 105-85 |
| ST1115 | STEEL COMP 1115 |
| ST1117 | STEEL COMP 1117 |
| ST1118 | STEEL COMP 1118 |
| ST1120 | STEEL COMP 1120 |
| ST1141 | STEEL COMP 1141 |
| ST0520 | STEEL COMP 120-95 |
| ST1212 | STEEL COMP 1212 |
| ST1213 | STEEL COMP 1213 |
| ST1215 | STEEL COMP 1215 |
| ST0531 | STEEL COMP 150-125 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0304 | STEEL COMP 304 |
| ST0316 | STEEL COMP 316 |
| ST0321 | STEEL COMP 321 |
| ST0324 | STEEL COMP 324 |
| ST0347 | STEEL COMP 347 |
| ST4130 | STEEL COMP 4130 |
| ST4140 | STEEL COMP 4140 |
| ST4150 | STEEL COMP 4150 |
| ST0416 | STEEL COMP 416 |
| ST0431 | STEEL COMP 431 |
| ST4340 | STEEL COMP 4340 |
| ST0107 | STEEL COMP 440C |
| ST4620 | STEEL COMP 4620 |
| ST0555 | STEEL COMP 60-30 |
| ST0630 | STEEL COMP 630 |
| ST0528 | STEEL COMP 80-40 |
| ST0184 | STEEL COMP 90-60 |
| ST0030 | STEEL COMP E52100 |
| ST0704 | STEEL COMP XM-12 |
| STB000 | STEEL CORROSION RESISTING |
| ST0586 | STEEL UNS J03001 |
| ST0594 | STEEL UNS J03008 |
| ST0587 | STEEL UNS J03501 |
| ST1598 | STEEL UNS J05002 |
| ST0626 | STEEL UNS J91152 |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TT0052 | TITANIUM ALLOY UNS R56400 |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCM2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CM | CUBIC METERS |
AAHJ*JFIRST END LENGTH FROM GROOVE TO END
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHJ3HMEJAA2.0*;AAHJ3HMEJAA2.0$JAA2.0*;AAHJ3HMEJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AEV | BOTH ENDS |
| 3HME | AA END |
| 3HMF | BB END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AAT | BODY |
| 3ACU | FLANGE |
| 3AEE | OVERALL |
| 3CYK | HUB |
| 3CYY | RIM |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 3 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)