An item fabricated in the form of an elbow and having both ends threaded female, or with unthreaded connecting facilities on both ends, or connecting facilities on both ends, one of which is a male thread without boss or shoulder. If a locknut or bondnut is included, it shall not be considered as a thread boss or shoulder. It is primarily intended to connect conduit to conduit. It may have a removable cover to facilitate pulling wires, but does not include facilities for mounting wiring devices. For items having a removable cover to facilitate pulling wires and specifically designed for close installation in exposed outdoor locations and which may have facilities for an outside driven ground, see ENTRANCE ELBOW, ELECTRICAL. For items with one end having a male thread with a boss or shoulder, see BOX CONNECTOR, ELECTRICAL. For items having a removable screw cap for pulling wires, with the cap positioned 45 degrees from the connection facilities, see ENTRANCE ELBOW, ELECTRICAL. For items fabricated in the form of an elbow having both ends threaded male, see BEND, ELECTRICAL CONDUIT.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED06944*)
APTDDEND TYPE
INDICATES THE TYPE OF END.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(APTD3AIFDAHM*;APTD3AIFDAHM$DAHT*;APTD3AIFDAHM$$DAHT*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AK84) | Reply |
| AHD | ADJUSTABLE CLAMP |
| AHE | ANGLE SETSCREW |
| AHF | CLAMP SQUEEZE |
| AHG | COMPRESSION RING AND NUT |
| AKF | CONVOLUTED |
| AHH | DOUBLE BIT SCREW CLAMP |
| AHJ | DOUBLE SETSCREW |
| AHK | DUPLEX CABLE |
| AKK | EXTERNAL CONVOLUTED SCREW IN |
| AKJ | EXTERNAL CONVOLUTIONS |
| AHL | EXTERNAL THREAD |
| AHN | FITTING/BOX CONNECTOR, 3 SECTION CABLE STOP |
| AHM | FITTING/BOX CONNECTOR, RING CABLE STOP |
| AHP | GLAND NUT W/EXTERNAL THREAD |
| AHQ | GLAND NUT W/INTERNAL THREAD |
| AHR | HINGED STRAP |
| AKL | INTERNAL CONVOLUTIONS |
| AHS | INTERNAL THREAD |
| AHT | OFFSET SCREW |
| AHW | ONE WAY BITE |
| AJQ | OVAL CONDUIT |
| AJR | REVERSIBLE CLAMP |
| AHX | RUBBER BUSHING, WATERTIGHT |
| AHY | RUBBER BUSHING, WATERTIGHT-1 HOLE |
| AHZ | RUBBER BUSHING, WATERTIGHT-2 HOLE |
| AJA | SCREW CLAMP |
| AHC | SELVAGED |
| AJB | SHOULDERED FERRULE W/HEXAGON NUT |
| AJC | SHOULDERED FERRULE W/ROUND NUT |
| AJD | SPANNER |
| AJE | SPLIT NIPPLE |
| AAL | SQUARE |
| AJF | SQUEEZE |
| AJG | STRAIGHT BITE |
| AJH | STRAIGHT BORE |
| AJJ | STRAIGHT SETSCREW |
| AJK | TAPER FIT |
| AJL | TRIPLE SETSCREW |
| AJM | TWO PIECE CLAMP |
| AJN | TWO SCREW CLAMP, CENTER CONNECTED |
| AJP | TWO SCREW CLAMP, END CONNECTED |
| ABF | UNTHREADED |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
AELSDCONDUIT TYPE ACCOMMODATED
INDICATES THE TYPE OF CONDUIT WHICH THE ITEM IS DESIGNED TO ACCOMMODATE.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AELS3AIFDD*;AELS3AIFDD$DY*;AELS3AIFDD$$DY*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AC23) | Reply |
| Y | ANY ACCEPTABLE |
| A | FLEXIBLE METALLIC |
| B | FLEXIBLE NONMETALLIC |
| D | RIGID METALLIC THICKWALL |
| C | RIGID METALLIC THINWALL |
| E | RIGID NONMETALLIC |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABEXJDEFLECTION ANGLE
THE DEGREE OF DEFLECTION BETWEEN TWO STRAIGHT LINES OF A CIRCLE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABEXJD2.0*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) A37, A38, A39, A40, A41 OR A38A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (CQMQ)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLLA41)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAQ1119 | A37 | PULLING-SIDE OPENING |
| AAQ1120 | A38 | PULLING-SCREW CAP |
| AAQ1162 | A38A | PULLING-TOP COVER PLATE |
| AAQ1121 | A39 | PULLING |
| AAQ1122 | A40 | COMPRESSION |
| AAQ1123 | A41 | STANDARD |
CQMQ*JLEG END TO PLANE OF BEND DISTANCE
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQMQ3AEUJAA2.0*;CQMQ3AEUJAA2.0$JAA2.0*;CQMQ3AEUJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDAL0024*;MATTDPPB000$DALA000*;MATTDPPB000$$DALA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2011 | ALUMINUM ALLOY 2011 |
| AL2017 | ALUMINUM ALLOY 2017 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6062 | ALUMINUM ALLOY 6062 |
| AL0024 | ALUMINUM ALLOY D712.0 |
| ALC000 | ALUMINUM-COPPER FREE |
| ASA000 | ASBESTOS |
| BRA000 | BRASS |
| BND000 | BRONZE |
| BNC000 | BRONZE SILICON |
| CDA000 | CADMIUM |
| CXA000 | CEMENT |
| CXC000 | CEMENT PORTLAND POZZUOLANA |
| CLA000 | CLAY |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0027 | COPPER ALLOY CA360 |
| CU1158 | COPPER ALLOY CU-AL9NI3FE2 |
| FBA000 | FIBER |
| FBR000 | FIBER ASBESTOS |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| FEF000 | IRON ALLOY |
| FEB000 | IRON CAST |
| FED000 | IRON CAST ALLOY |
| FEC000 | IRON MALLEABLE |
| NLA000 | NICKEL |
| PPA000 | PAPER |
| PPB000 | PAPER BARRIER |
| PCA000 | PLASTIC |
| PCH000 | PLASTIC EPOXY |
| PCCB00 | PLASTIC NYLON |
| PCM000 | PLASTIC PHENOL FORMALDEHYDE (PMO) |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE (NYLON) |
| PCR000 | PLASTIC POLYCARBONATE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE (PVC) |
| PCAS00 | PLASTIC POLYVINYLIDENE FLUORIDE |
| CLB000 | PORCELAIN |
| RCD000 | RUBBER CHLOROPRENE |
| RCB000 | RUBBER SYNTHETIC |
| SLD000 | SILICA |
| CXD000 | SILICA PORTLAND CEMENT |
| SLC000 | SILICON |
| SLE000 | SOAPSTONE |
| STA000 | STEEL |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1010 | STEEL COMP 1010 |
| ST1011 | STEEL COMP 1011 |
| ST1012 | STEEL COMP 1012 |
| ST1013 | STEEL COMP 1013 |
| ST1015 | STEEL COMP 1015 |
| ST1016 | STEEL COMP 1016 |
| ST1017 | STEEL COMP 1017 |
| ST1018 | STEEL COMP 1018 |
| ST1019 | STEEL COMP 1019 |
| ST1020 | STEEL COMP 1020 |
| ST1021 | STEEL COMP 1021 |
| ST1022 | STEEL COMP 1022 |
| ST1023 | STEEL COMP 1023 |
| ST1024 | STEEL COMP 1024 |
| ST1025 | STEEL COMP 1025 |
| ST1110 | STEEL COMP 1110 |
| ST1111 | STEEL COMP 1111 |
| ST1112 | STEEL COMP 1112 |
| ST1113 | STEEL COMP 1113 |
| ST1115 | STEEL COMP 1115 |
| ST1116 | STEEL COMP 1116 |
| ST1117 | STEEL COMP 1117 |
| ST1118 | STEEL COMP 1118 |
| ST1119 | STEEL COMP 1119 |
| ST0063 | STEEL COMP 12L14 |
| ST0016 | STEEL COMP B1113 |
| ST0046 | STEEL COMP MT1010 |
| ST0047 | STEEL COMP MT1015 |
| ST0048 | STEEL COMP MT1020 |
| ST0049 | STEEL COMP MTX1015 |
| ST0050 | STEEL COMP MTX1020 |
| STB000 | STEEL CORROSION RESISTING |
| STC000 | STEEL STAINLESS - USE STB000 |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
AARX*JINSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR FIGURE OR BODY,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AARX3AEUJAB2.0*;AARX3AEUJAB2.0$JAB2.0*;AARX3AEUJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIB | THIRD END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQYR*JITEM ACCOMMODATED TRADE SIZE
THE NOMINAL SIZE THAT INDICATES THE ACTUAL INSIDE DIAMETER OF THE ITEM ACCOMMODATED.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQYR3AETJA2.0*;CQYR3AETJA2.0$JA2.0*;CQYR3AETJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDPBA000*;SFTTDVAA000$DENA000*;SFTTDVAA000$$DENA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CDB000 | CADMIUM ALLOY |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| AUA000 | GOLD |
| LQA000 | LACQUER |
| LQC000 | LACQUER ALUMINUM |
| LQB000 | LACQUER ALUMINUM CELLULOSE |
| PBA000 | LEAD |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| AGA000 | SILVER |
| SNA000 | TIN |
| VAA000 | VARNISH |
| ZNA000 | ZINC |
IF YOU ANSWER MRC STDC, YOU MUST ANSWER MRC (SFTT)
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
IF STYLE/REPLY CODE(s) NS OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQRN)
IF STYLE/REPLY CODE(s) GA, SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQQR and CTTC)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(THSD3AEEDUN*;THSD3AEEDUN$DNT*;THSD3AEEDUN$$DNT*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH06) | Reply |
| GA | ARMOURED CONDUIT, DIN 40430 |
| CQ | BS CON |
| DX | FRENCH CONDUIT THREAD NF C68-190 |
| SM | ISO M |
| SS | ISO S |
| EM | M |
| MJ | MJ |
| SL | NPSL |
| NP | NPT |
| NT | NPTF |
| TS | NPTS |
| SJ | SI |
| SK | SI-M |
| AY | SPECIAL |
| UN | UN |
| NE | UNEF |
| NF | UNF |
| NC | UNIFIED NATIONAL COARSE (UNC) |
| JF | UNIFIED NATIONAL JOINT FINE (UNJF) |
| JC | UNJC |
| NS | UNS |
| WW | WHITWORTH |
CQRN*JTHREAD QUANTITY
THE NUMBER OF THREADS PER SPECIFIC MEASUREMENT SCALE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CQRN3AETJD2.0*;CQRN3AETJD2.0$JD2.0*;CQRN3AETJD2.0$$JD2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AB39) | Reply |
| D | PER CENTIMETER |
| C | PER INCH |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(CQQR3AEUB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AEU | SECOND END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CTTC3AEUJEXT2.0*;CTTC3AEUJEXT2.0$JEXT2.0*;CTTC3AEUJEXT2.0$$JEXT2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJX3AEUJA2.0*;CQJX3AEUJA2.0$JA2.0*;CQJX3AEUJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(AAJD3AEUAQ0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AAJF*DTHREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AAJF3AEEDAAL*;AAJF3AEEDAAL$DAAG*;AAJF3AEEDAAL$$DAAG*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3AIF | SINGLE END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA38) | Reply |
| AAG | LEFT-HAND |
| AAL | RIGHT-HAND |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASA3AETJAB2.0*;AASA3AETJAB2.0$JAB2.0*;AASA3AETJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AET | FIRST END |
| 3AEU | SECOND END |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADTS*DCONSTRUCTION TYPE
INDICATES THE TYPE OF CONSTRUCTION.
Enter the applicable reply code from the table below
(ADTSDAAJ)
| Table 1 |
| Reply Code (AC66) | Reply |
| AAJ | ONE PIECE |
| AAN | TWO PIECE |
ABFE*DHAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION
THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS.
Enter the applicable reply code from the table below
(ABFEDCK*;ABFEDAC$$DCF*)
| Table 1 |
| Reply Code (AB27) | Reply |
| AA | ACID RESISTANT |
| BN | AIRTIGHT |
| DM | AROMATIC HYDROCARBONS RESISTANT |
| AB | CEMENT TIGHT |
| GD | COLD RESISTANT |
| FW | CONDENSATION PROOF |
| ED | CORROSION PROOF |
| AC | DRIPTIGHT-NEMA TYPE 2 |
| EF | DUST RESISTANT |
| EH | DUST-IGNITION PROOF |
| CF | DUSTPROOF |
| AD | DUSTPROOF-NEMA TYPE 13 |
| DY | DUSTTIGHT |
| AE | DUSTTIGHT-NEMA TYPE 5 |
| FR | ELECTROMAGNETIC INTERFERENCE SHIELDED |
| CE | EXPLOSION PROOF |
| EY | EXPLOSION PROOF NEC CL. I, GP. ABCD;CL. II, GP. EFG |
| EZ | EXPLOSION PROOF NEC CL. I, GP. B |
| FA | EXPLOSION PROOF NEC CL. I, GP. CD |
| AF | EXPLOSION PROOF NEC CL.I, GP.ABCD;CL.II, GP.EFG;CL.III |
| AH | EXPLOSION PROOF NEC CL.I, GP.BC;CL.II, GP.EFG;CL.III |
| AG | EXPLOSION PROOF NEC CL.I, GP.BCD;CL.II, GP.EFG;CL.III |
| FT | EXPLOSION PROOF NEC CL.I, GP.CD;CL.I, II, III, GP.EFG |
| AW | EXPLOSION PROOF NEC CL.I, GP.CD;CL.II, GP.EFG |
| AJ | EXPLOSION PROOF NEC CL.I, GP.CD;CL.II, GP.EFG;CL.III |
| FK | EXPLOSION PROOF NEC CL.I, GP.CD;CL.II, GP.G;CL.III |
| AL | EXPLOSION PROOF NEC CL.I, GP.D;CL.II, GP.EFG |
| AK | EXPLOSION PROOF NEC CL.I, GP.D;CL.II, GP.EFG;CL.III |
| AM | EXPLOSION PROOF NEC CL.I, GP.D;CL.II, GP.G |
| FL | EXPLOSION PROOF NEC CL.II, GP.AB |
| AN | EXPLOSION PROOF NEC CL.II, GP.EFG;CL.III |
| GF | FLAMEPROOF |
| GL | FRACTUREPROOF |
| DP | FUEL RESISTANT |
| CH | FUNGUS RESISTANT |
| AT | GASTIGHT |
| AP | GENERAL PURPOSE-NEMA TYPE 1 |
| DQ | GREASE RESISTANT |
| DR | HEAT RESISTANT |
| GM | IMPACT RESISTANT |
| CP | LIQUID TIGHT |
| DV | MOISTURE PROOF |
| BR | MOISTURE RESISTANT |
| CJ | OILTIGHT |
| AQ | OILTIGHT-NEMA TYPE 11 |
| BL | RADIO FREQUENCY INTERFERENCE |
| CK | RAINPROOF |
| EM | RAINTIGHT |
| AR | RAINTIGHT-NEMA TYPE 3R |
| GC | SALT SPRAY PROOF |
| DT | SALT WATER RESISTANT |
| EJ | SHOCK PROOF |
| EP | SHOCK RESISTANT |
| AS | SUBMERSIBLE-NEMA TYPE 6 |
| FM | VIBRATION PROOF |
| EA | WATER RESISTANT |
| CN | WATERTIGHT |
| AU | WATERTIGHT-NEMA TYPE 4 |
| EG | WEATHER RESISTANT |
| DX | WEATHERPROOF |
| AV | WEATHERPROOF-NEMA TYPE 3 |
| GG | WEATHERTIGHT |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDACH*;ABFFDAWD$$DAFY*)
| Table 1 |
| Reply Code (AB28) | Reply |
| ACE | 4 HOLE INSULATOR DISK |
| ACH | ADAPTER |
| ATS | BASKET WEAVE GRIP |
| AJZ | BONDNUT |
| AJM | BUSHING |
| AKL | BUSHING INSULATOR |
| AWD | BUSHING W/HOLE |
| AKE | CABLE CLAMP |
| ATL | CLAMP RING |
| AQN | CLAMPING NUT |
| AKP | CLOSE NIPPLE |
| ATF | COLLAR |
| AWA | COLLAR ADAPTER |
| AJS | COMPRESSION RING |
| ATX | CONNECTOR ADAPTER |
| ATJ | COUPLING RING |
| AKG | COVER |
| AKR | DOWEL PIN |
| AKJ | DRAIN FITTING |
| ATT | EXTERNALLY THREADED HUB |
| ATH | EYELET |
| AKH | FERRULE |
| ACN | GASKET |
| AKK | GLAND |
| AES | GLAND NUT |
| AKY | GLAND WASHER |
| ADM | GROMMET |
| AKS | GROMMET RING |
| AKF | GROUNDING CONE |
| ATN | GROUNDING CONNECTOR |
| AKM | GROUNDING JUMPER |
| AKW | GROUNDING SCREW |
| ATM | HEX COUPLING NUT |
| AKA | INSULATED BUSHING |
| AKT | INSULATING RING |
| AKX | INSULATION SLEEVING |
| ATP | INSULATOR |
| AKD | KNOCKOUT CAP |
| ADW | LOCKNUT |
| AKN | NIPPLE |
| ABW | NUT |
| AKB | OVAL BUSHING |
| AKQ | PACKING |
| AEA | PLUG |
| ADZ | PREFORMED PACKING |
| AJX | REDUCING WASHER |
| AFF | RETAINING RING |
| AKC | ROUND BUSHING |
| AMX | SCREW |
| AJQ | SCREW IN GROUNDING CONE |
| AAG | SEALING RING |
| AJY | SEALING WASHER |
| AFJ | SETSCREW |
| AAH | SHELL GROUNDING LUG |
| AJP | SHORT COUPLING |
| ACX | SLEEVE |
| ACD | SLEEVE ASSEMBLY |
| ATG | SPLIT BUSHING |
| ATK | SPLIT CAP |
| AJT | SPLIT LEAD SLEEVE |
| ATZ | SWAGE NUT |
| AJN | TAPERED BUSHING |
| AFY | TAPERED PIN |
| ATY | THREAD ADAPTER |
| AJW | WASHER |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCVB*;CBBLDCUZ$$DAMZ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AMY | CRIMP CONNECTION |
| CUZ | INSIDE OPENING |
| CVA | OUTSIDE OPENING |
| BNY | REMOVABLE COVER |
| AMZ | SAFETY WIRE HOLE |
| CVB | TOP OPENING |
MARK*GSPECIAL MARKINGS
MARKINGS INCLUDED ON AN ITEM FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE, FUNCTION, OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURER'S PART NUMBERS, SYMBOLS, OR THE LIKE.
Enter clear text.
(MARKGCLEARTEXT)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
AFJQ*JSTORAGE TEMP RANGE
THE MINIMUM AND MAXIMUM TEMPERATURES AT WHICH AN ITEM CAN BE STORED WITHOUT DETRIMENTAL EFFECT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFJQJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
BBRG*DSTORAGE TYPE
INDICATES THE TYPE OF STORAGE SPACE REQUIRED FOR AN ITEM IN ORDER TO PROVIDE THE DEGREE OF PROTECTION NECESSARY TO MAINTAIN SERVICEABILITY STANDARDS.
Enter the applicable reply code from the table below
(BBRGDAR*;BBRGDAG$DAK*)
| Table 1 |
| Reply Code (AM81) | Reply |
| AE | GENERAL PURPOSE WAREHOUSE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AK | UNIMPROVED OPEN |
BBRH*JINSPECTION FREQUENCY
THE SPECIFIED TIME INTERVAL,FROM RECEIPT,NECESSARY TO DETECT MATERIAL DETERIORATION THAT WILL AFFECT STOCK READINESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit.
(BBRHJMHAB2*;BBRHJMHAB2$$JMHAB3*)
| Table 1 |
| Reply Code (AH68) | Reply |
| MH | MONTHS |
| YR | YEARS |
| Table 2 |
| Reply Code (AM82) | Reply |
| AB | FIRST INSPECTION |
| AC | REINSPECTION |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDAGA000$DPDA000*;PRMTDAGA000$$DPDA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAZA0002.0*;PMLCJAZA0002.0$JAZA0002.0*;PMLCJAZA0002.0$$JAZA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJRHA000E2.0*;PMWTJRHA000E2.0$JRHA000E2.0*;PMWTJRHA000E2.0$$JRHA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ011*;HZRDDHAZ042$$DHAZ012*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ042 | ASBESTOS |
| HAZ008 | CADMIUM |
| HAZ011 | CHROMIUM |
| HAZ012 | COPPER |
| HAZ029 | LEAD |
| HAZ052 | ZINC |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)