An electrical fitting designed to connect one or more lamps or lampbases to an electrical CONNECTOR (as modified). May include integral switch or side wire outlet. Excludes:ADAPTER, LAMPHOLDER TO CONNECTOR.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED05763*)
AEUHALAMP ACCOMMODATION QUANTITY
THE NUMBER OF LAMPS THAT CAN BE ACCOMMODATED BY THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AEUHA10*)
AZQCLLAMP BASE STYLE ACCOMMODATED
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE LAMP BASE THE ITEM IS DESIGNED TO ACCOMMODATE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AZQCL35)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAO1484 | 1 | MIDGET SCREW |
| AAO1492 | 10 | DOUBLE CONTACT CANDELABRA PREFOCUS |
| DR01123 | 11 | DOUBLE CONTACT BAYONET CANDELABRA SKIRTED |
| AAO1494 | 12 | SLIDE |
| AAO1495 | 13 | DOUBLE CONTACT BAYONET CANDELABRA |
| DR01223 | 14A | SINGLE PIN T-5 |
| DR01224 | 14B | SINGLE PIN T-6 |
| DR01225 | 14C | SINGLE PIN T-8 |
| DR01226 | 14D | SINGLE PIN T-12 |
| DR01127 | 15 | MEDIUM BIPOST |
| DR01242 | 16A | MINIATURE BIPIN |
| DR01243 | 16B | MEDIUM BIPIN T-8 |
| DR01244 | 16C | MEDIUM BIPIN T-12 |
| DR01245 | 16D | MOGUL BIPIN |
| AAO1497 | 17 | THREE CONTACT LUGS |
| DR01128 | 18 | 4-PIN |
| AAO1499 | 19 | SCREW TERMINALS |
| AAO1485 | 2 | MIDGET FLANGE |
| DR01161 | 20 | MOGUL BIPOST |
| DR01246 | 21A | THREE CONTACT MEDIUM SCREW |
| DR01247 | 21B | THREE CONTACT MOGUL SCREW |
| DR01248 | 22A | MINIATURE SCREW |
| DR01249 | 22B | CANDELABRA SCREW |
| DR01250 | 22C | INTERMEDIATE SCREW |
| DR01251 | 22D | MEDIUM SCREW |
| DR01252 | 22E | ADMEDIUM SCREW |
| DR01253 | 22F | MOGUL SCREW |
| DR01279 | 23A | MEDIUM PREFOCUS |
| DR01280 | 23B | MOGUL PREFOCUS |
| DR01281 | 24A | SINGLE CONTACT CANDELABRA PINLESS |
| DR01282 | 24B | MINIATURE PINLESS |
| DR01298 | 25A | CANDELABRA SCREW SKIRTED |
| DR01299 | 25B | MEDIUM SCREW SKIRTED |
| DR01300 | 25C | ADMEDIUM SCREW SKIRTED |
| AAO1501 | 26 | SPECIAL GUNSIGHT SCREW |
| DR01162 | 27 | SPECIAL 952 |
| AAO1537 | 28A | 3 PRONG |
| AAO1538 | 28B | 2 PRONG |
| AAO1503 | 29 | SPECIAL INSTRUMENT SLIDE |
| AAO1486 | 3 | KOLLSMAN |
| AAO1504 | 30 | MOUNTING LUGS AND BEADED WIRE LEADS |
| AAO1505 | 31 | BRASS FERRULE |
| AAO1506 | 32 | THREE CONTACT MEDIUM BAYONET |
| AAO1507 | 33 | FLEXIBLE LEAD |
| AAO1508 | 34 | DOUBLE CONTACT CANDELABRA PINLESS |
| AAO1509 | 35 | DOUBLE INTERMEDIATE SCREW |
| AAO1510 | 36 | SURGICAL FLANGE, STYLE 1 |
| AAO1511 | 37 | SURGICAL FLANGE, STYLE 2 |
| AAO1512 | 38 | SURGICAL SCREW |
| AAO1513 | 39 | DOUBLE CONTACT MEDIUM RING |
| AAO1487 | 4 | MINIATURE FLANGE |
| AAO1514 | 40 | B AND H RING |
| AAO1515 | 41 | SMALL INDEXING RING |
| AAO1516 | 42 | LARGE INDEXING RING |
| AAO1517 | 43 | VENTED LARGE INDEXING RING |
| AAO1539 | 44A | MOGUL END PRONG |
| AAO1540 | 44B | TWO CONTACT LUGS |
| AAO1518 | 45 | MEDIUM SIDE PRONG |
| DR01163 | 46 | GROOVED MIDGET |
| AAO1520 | 47 | UNTHREADED CYLINDER W/SCREW TERMINAL |
| DR01164 | 48 | 4-PIN INDEXING |
| DR01210 | 49 | MINIATURE 2 PIN |
| AAO1488 | 5 | DISK |
| AAO1523 | 50 | BRASS FERRULE, STYLE 2 |
| AAO1524 | 51 | POLARIZED SUBMINIATURE BIPIN |
| AAO1525 | 52 | TAB |
| DR01213 | 53 | GLASS GROOVE |
| AAO1527 | 54 | RECESSED SINGLE CONTACT |
| AAO1528 | 55 | RECESSED DOUBLE CONTACT |
| AAO1489 | 6 | SINGLE CONTACT BAYONET CANDELABRA INDEXING |
| DR01221 | 7A | SINGLE CONTACT BAYONET CANDELABRA |
| DR01222 | 7B | MINIATURE BAYONET |
| DR01117 | 8 | DOUBLE CONTACT BAYONET CANDELABRA |
| AAO1491 | 9 | SINGLE CONTACT CANDELABRA PREFOCUS |
AFRAACONTACT QUANTITY
THE NUMBER OF CONTACTS WHICH PROVIDE ELECTRICAL CONNECTION.
Enter the numeric reply with a minimum of one digit.
(AFRAA10*)
AAJS*DDESIGN CONFIGURATION
THE BASIC SHAPE,APPLICATION AND SURFACE FEATURES,AND THE LIKE,OF THE ITEM.
Enter the applicable reply code from the table below
(AAJSDAV*;AAJSDAU$$DAU*)
| Table 1 |
| Reply Code (AA43) | Reply |
| AV | FEMALE |
| AU | MALE |
AFRB*LCONTACT STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE CONTACT.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AFRBL9*;AFRBL1$$L6*)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAO1541 | 1 | FLAT |
| AAO1550 | 10 | ROUND OR PIN |
| AAO1551 | 11 | BANANA |
| AAO1552 | 12 | COAXIAL, PLAIN |
| AAO1553 | 13 | COAXIAL, OVERLAP |
| AAO1554 | 14 | TWINAXIAL |
| AAO1555 | 15 | CURVED BUTT |
| AAO1556 | 16 | SQUARE OR RECTANGULAR BUTTON |
| AAO1557 | 17 | ROUND BUTTON |
| AAO1558 | 18 | SCREW |
| AAO1559 | 19 | LEAF SPRING (PARTIAL SECTION) |
| AAO1542 | 2 | TEE |
| AAO1560 | 20 | WIRE SPRING (PARTIAL SECTION) |
| AAO1561 | 22 | TRIAXIAL |
| AAO1543 | 3 | ELL |
| AAO1544 | 4 | TOED ELL |
| AAO1545 | 5 | VEE |
| AAO1546 | 6 | U-HOLLOW |
| AAO1547 | 7 | U-SOLID |
| AAO1548 | 8 | CURVED, W/ OR W/O HEEL |
| AAO1549 | 9 | CURVED, LIPPED |
AZQE*DTWO FLAT CONTACT POSITION
A DESIGNATION THAT DESCRIBES THE BASIC ELECTRICAL CONFIGURATION OF THE TWO FLAT CONTACTS ARRANGEMENT.
Enter the applicable reply code from the table below
(AZQEDB*;AZQEDD$$DC*)
| Table 1 |
| Reply Code (AD19) | Reply |
| B | PARALLEL |
| D | RIGHT ANGLE |
| C | TANDEM |
AECQ*DELECTRICAL POLARIZATION
AN INDICATION OF WHETHER OR NOT THE ITEM NORMALLY WILL ACCEPT FLOW OF CURRENT IN ONE DIRECTION ONLY.
Enter the applicable reply code from the table below
(AECQDN*;AECQDP$$DN*)
| Table 1 |
| Reply Code (AC80) | Reply |
| N | NONPOLARIZED |
| P | POLARIZED |
AEEA*DSWITCH TYPE
INDICATES THE TYPE OF SWITCH INCLUDED IN THE ITEM.
Enter the applicable reply code from the table below
(AEEADAB*;AEEADAA$DAC*)
| Table 1 |
| Reply Code (AC82) | Reply |
| AA | PULL |
| AB | PUSH |
| AC | PUSH-PULL |
| AD | ROTARY |
| AG | TOGGLE |
APFY*BMAXIMUM VOLTAGE RATING IN VOLTS
THE MAXIMUM VOLTAGE RATING AT WHICH THE ITEM IS DESIGNED TO OPERATE,EXPRESSED IN VOLTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(APFYB2.0)
AEWK*JMAXIMUM CURRENT RATING
THE MAXIMUM CONTINUOUS CURRENT WHICH MUST NOT BE EXCEEDED IN ORDER TO AVOID DAMAGE TO THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWKJA2.0*)
| Table 1 |
| Reply Code (AC30) | Reply |
| A | AMPERES |
| U | MICROAMPERES |
| L | MILLIAMPERES |
AZQH*BMAXIMUM WATTAGE RATING IN WATTS
THE MAXIMUM RATED POWER THAT AN ITEM CAN SAFELY CONSUME OR PROVIDE,MEASURED IN WATTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AZQHB2.0)
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDPBB000*;MATTDST0347$DNLB000*;MATTDST0347$$DNLB000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL1100 | ALUMINUM ALLOY 1100 |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL0031 | ALUMINUM ALLOY 380.0 |
| AL5052 | ALUMINUM ALLOY 5052 |
| AL5083 | ALUMINUM ALLOY 5083 |
| AL5086 | ALUMINUM ALLOY 5086 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL6063 | ALUMINUM ALLOY 6063 |
| AL7075 | ALUMINUM ALLOY 7075 |
| CSA000 | CELLULOSE |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0059 | COPPER ALLOY 101 |
| CU0249 | COPPER ALLOY 102 |
| CU0286 | COPPER ALLOY 104 |
| CU0287 | COPPER ALLOY 105 |
| CU0288 | COPPER ALLOY 107 |
| CU0060 | COPPER ALLOY 11 |
| CU0063 | COPPER ALLOY 110 |
| CU0064 | COPPER ALLOY 111 |
| CU0289 | COPPER ALLOY 113 |
| CU0290 | COPPER ALLOY 114 |
| CU0291 | COPPER ALLOY 116 |
| CU0278 | COPPER ALLOY 125 |
| CU0315 | COPPER ALLOY 130 |
| CU0069 | COPPER ALLOY 172 |
| CU0233 | COPPER ALLOY 173 |
| CU0079 | COPPER ALLOY 260 |
| CU0080 | COPPER ALLOY 268 |
| CU0091 | COPPER ALLOY 360 |
| CU0103 | COPPER ALLOY 510 |
| CU0104 | COPPER ALLOY 511 |
| CU0670 | COPPER ALLOY 670 |
| CU0148 | COPPER ALLOY 745 |
| GSA000 | GLASS |
| GSB000 | GLASS FIBER |
| AUA000 | GOLD |
| FEA000 | IRON |
| FEB000 | IRON CAST |
| PBB000 | LEAD ALLOY |
| MGA000 | MAGNESIUM |
| NLA000 | NICKEL |
| NLB000 | NICKEL ALLOY |
| PCA000 | PLASTIC |
| PCD000 | PLASTIC ACRYLIC |
| PCH000 | PLASTIC EPOXY |
| PCJ000 | PLASTIC MELAMINE |
| PCK000 | PLASTIC METHYL METHACRYLATE |
| PCM000 | PLASTIC PHENOL-FORMALDEHYDE |
| PCN000 | PLASTIC PHENOLIC |
| PCP000 | PLASTIC POLYAMIDE |
| PCY000 | PLASTIC POLYETHYLENE TEREPHTHALATE |
| PCAD00 | PLASTIC POLYSTYRENE |
| PCAE00 | PLASTIC POLYSULFONE |
| PCAF00 | PLASTIC POLYTETRAFLUOROETHYLENE |
| PCAW00 | PLASTIC TETRAFLUOROETHYLENE |
| PTB000 | PLATINUM ALLOY |
| CLB000 | PORCELAIN |
| RSC000 | RESIN NATURAL |
| RSA000 | RESIN SYNTHETIC |
| RCE000 | RUBBER |
| AGA000 | SILVER |
| STA000 | STEEL |
| ST1008 | STEEL COMP 1008 |
| ST1009 | STEEL COMP 1009 |
| ST1015 | STEEL COMP 1015 |
| ST1018 | STEEL COMP 1018 |
| ST1020 | STEEL COMP 1020 |
| ST1045 | STEEL COMP 1045 |
| ST1050 | STEEL COMP 1050 |
| ST1055 | STEEL COMP 1055 |
| ST1065 | STEEL COMP 1065 |
| ST1075 | STEEL COMP 1075 |
| ST1085 | STEEL COMP 1085 |
| ST1095 | STEEL COMP 1095 |
| ST0301 | STEEL COMP 301 |
| ST0302 | STEEL COMP 302 |
| ST0303 | STEEL COMP 303 |
| ST0304 | STEEL COMP 304 |
| ST0347 | STEEL COMP 347 |
| ST0348 | STEEL COMP 348 |
| ST4130 | STEEL COMP 4130 |
| ST0416 | STEEL COMP 416 |
| STB000 | STEEL CORROSION RESISTING |
| ZNB000 | ZINC |
| ZNA000 | ZINC ALLOY |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| B | FED SPEC |
| C | FED STD |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| B | 1ST MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDZNA000*;SFTTDALA000$DCUA000*;SFTTDALA000$$DCUA000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ALA000 | ALUMINUM ALLOY |
| ANA000 | ANODIZE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| END000 | ENAMEL BAKED |
| AUA000 | GOLD |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PCH000 | PLASTIC VINYL |
| RHA000 | RHODIUM |
| AGA000 | SILVER |
| SNA000 | TIN |
| ZNA000 | ZINC |
| ZNB000 | ZINC ALLOY |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFQV*;CBBLDBAX$$DBAX*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BAX | COMPONENT SWITCH |
| FQV | SIDE WIRE OUTLET |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| CS | CONSTRUCTION |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| FN | FINISH |
| FM | FORM |
| FA | FORMULA |
| GR | GRADE |
| GP | GROUP |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| NR | NUMBER |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| QA | QUALITY |
| RN | RANGE |
| RT | RATING |
| RF | REFERENCE NUMBER |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCC2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CF | CUBIC FEET |
| CN | CUBIC INCHES |
| CM | CUBIC METERS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDPDA000$DPTA000*;PRMTDPDA000$$DPTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJAUA000E2.0*;PMWTJAUA000E2.0$$JAUA000E2.1*;PMWTJAUA000E2.0$JAUA000E2.0*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPDA000TEXT1234*;PMLCJPDA000TEXT1234$$JPDA000TEXT1234*;PMLCJPDA000TEXT1234$JPDA000TEXT1234*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
FCLS*AFUNCTIONAL CLASSIFICATION
THE ALPHA-NUMERIC DESIGNATION THAT IDENTIFIES THE CLASSIFICATION OF THE ITEM ACCORDING TO THE CATEGORY OF FUNCTIONS PERFORMED.
Enter the alpha-numeric reply with a minimum of one character.
(FCLSAH4)
FTLD*GFUNCTIONAL DESCRIPTION
DESCRIBES THE CAPABILITIES,INTENDED USE,AND/OR PURPOSE FOR WHICH THE ITEM IS PROVIDED.
Enter the reply from the applicable document.
(FTLDGUSED TO INSTALL/REMOVE ENGINE NACELLE*)
TMDN*ATYPE/MODEL DESIGNATION
THE ALPHA-NUMERIC-ALPHA DESIGNATION USED TO IDENTIFY THE TYPE AND/OR MODEL OF THE BASIC ITEM.
Enter the alpha-numeric reply with a minimum of one character.
(TMDNAM1)
RTSE*GRELATIONSHIP TO SIMILAR EQUIPMENT
INDICATES THE RELATIONSHIP,SUCH AS CONSTRUCTION,CAPABILITIES,AND THE LIKE,OF THE ITEM TO A SIMILAR ITEM.
Enter concise statement for similar item including name and identifying data.
(RTSEGSIMILAR TO LOCKHEED OVERWING ENGINE HOIST P/N 61521-58*)
RDAL*GREFERENCE DATA AND LITERATURE
LITERATURE AND REFERENCES AVAILABLE FOR INFORMATION PERTAINING TO THE ITEM.
Enter data appropriate and in a concise manner to identify informational references covering the item.
(RDALGNAAVAIROIA/VFK58 A-2.2.9*)
NTRD*AENTRY DATE
INDICATES THE DATE THE ITEM WAS ENTERED INTO MIL-HDBK-300.
Enter the date structured in three hyphenated 2 position segments to indicate the last 2 digits of the calendar year, month, and day.
(NTRDA80-05-28*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information