A component of an automatic pilot system designed to regulate the speed of a hydraulic servo cylinder's response to control signals by means of manual adjustments.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED05152*)
AZKQ*JTEMP RATING
A VALUE WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,OF AN ITEM.
Enter the applicable Reply Code from Tables 1 and 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit as in the first and second examples. For negative temperature values, precede the numeric portion of the reply with the letter “M” as in the third and fourth examples.
(AZKQJFA68.0*; AZKQJCB0.0$$JCC35.0*; AZKQJFCM15.0*; AZKQJFBM40.0$$JFC75.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEVZJMAXIMUM INLET PRESSURE RATING
THE MAXIMUM PRESSURE OF THE MEDIA ON THE INLET SIDE AT WHICH AN ITEM IS DESIGNED TO OPERATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEVZJV2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AEWA*JOUTLET PRESSURE SETTING
THE SET /NONADJUSTABLE/ PRESSURE OF THE MEDIA ON THE OUTLET SIDE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWAJV2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AEVA*JOUTLET PRESSURE RANGE
THE MINIMUM TO MAXIMUM LIMITS OF OUTLET PRESSURE OF THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AEVAJKM32.0/P50.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AEWBJOUTLET PRESSURE ACCURACY RATING
THE RATED VARIANCE OF THE OUTLET PRESSURE FROM THE SET PRESSURE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEWBJV2.0*)
| Table 1 |
| Reply Code (AB18) | Reply |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| V | POUNDS PER SQUARE INCH |
AEWFDFILTER
AN INDICATION OF WHETHER OR NOT A FILTER IS INCLUDED.
Enter the applicable reply code from the table below
(AEWFDB)
| Table 1 |
| Reply Code (AA49) | Reply |
| B | INCLUDED |
| C | NOT INCLUDED |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDYX*;ABFFDYN$DCW*;ABFFDYN$$DCW*)
| Table 1 |
| Reply Code (AB28) | Reply |
| CN | ADAPTER |
| YP | ADJUSTMENT STEM |
| CP | AUTOMATIC RELIEF VALVE |
| YT | BONNET |
| YK | BRAZING RING |
| YR | CRANK |
| CQ | CYLINDER GAGE |
| CR | DELIVERY GAGE |
| YZ | DIAL |
| YQ | DUMP VALVE |
| CS | EXTERNAL PILOT VALVE |
| CT | FLOWMETER |
| YV | INDICATOR |
| YL | INLET ADAPTER |
| CU | INLET PRESSURE GAGE |
| YM | INLET STRAINER |
| YN | INTERNAL BYPASS VALVE |
| CV | INTERNAL PILOT VALVE |
| ZA | LEVER HANDLE |
| CW | NEEDLE VALVE |
| ED | NUT |
| EE | NUT AND SLEEVE |
| CX | OUTLET PRESSURE GAGE |
| AFR | PANEL MOUNTING BRACKET |
| AFE | PREINSERTED BRAZING RING |
| CY | PRESSURE BREAKER |
| AFS | PUSHBUTTON CLEANING RESTRICTION |
| YW | STRAINER |
| YX | TAILPIECE |
| AFQ | TAILPIECE W/GROOVES |
| CZ | TEMPERATURE GAGE |
| CC | THERMOMETER |
| YY | UNION NUT |
| YS | WRENCH |
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CCFG*JVALVE SIZE
DESIGNATES THE SIZE OF THE VALVE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CCFGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ADQUDFLOW CONTROL DEVICE
THE PART THAT CONTROLS THE FLOW THROUGH THE ITEM.
Enter the applicable reply code from the table below
(ADQUDAQ*;ADQUDCM$DCK*;ADQUDCM$$DCK*)
| Table 1 |
| Reply Code (AC57) | Reply |
| AA | BALL |
| AB | BALL, PORTED |
| CT | BELLOWS |
| CV | BULB |
| AC | CONE |
| AD | CONE, BOTTOM GUIDED |
| AE | CONE, TOP GUIDED |
| AQ | DIAPHRAGM |
| BP | DISK |
| CL | DISK, BEVEL SEAT, BOTTOM GUIDED |
| CK | DISK, BEVEL SEAT, TOP GUIDED |
| AM | DISK, BOTTOM GUIDED |
| AF | DISK, CIRCULAR |
| AZ | DISK, DUAL |
| CM | DISK, DUAL, TOP GUIDED |
| AG | DISK, FLAT |
| AN | DISK, FLAT, BOTTOM GUIDED |
| AP | DISK, FLAT, TOP AND BOTTOM GUIDED |
| CN | DISK, GUIDED |
| AH | DISK, PLUG TYPE |
| AJ | DISK, SOLID WEDGE |
| AK | DISK, SPLIT WEDGE |
| AR | DISK, SWING TYPE |
| AL | DISK, TOP GUIDED |
| CP | DOUBLE SEATED |
| AS | NEEDLE |
| CR | PISTON, BOTTOM GUIDED |
| AT | PISTON, FREE TYPE |
| CH | PISTON, SPRING LOADED |
| CQ | PISTON, TOP GUIDED |
| AU | PISTON, WEIGHTED TYPE |
| AV | PLUG |
| AW | POPPET |
| CS | POPPET, DUAL DISK |
| AX | STEM AND INTEGRAL DISK |
BZRS*GEND CONNECTION SPEC/STD
THE SPECIFICATION AND/OR STANDARD OF THE END CONNECTION.
Enter clear text.
(BZRSGCLEARTEXT)
ADQZAEND CONNECTION QUANTITY
THE NUMBER OF END CONNECTIONS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ADQZA10*)
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLH and ACLL and ACLK) or (ACKN and ACLH and ACLL and ADRN)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLH)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLL)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLG)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACKT)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLE and ADRN and ACLL)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLE and ACLF)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLF and ADRN and ACLL)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLF)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ADRN and ACLL)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACKM, YOU MUST ANSWER MRC (ACKN and ACLL and ACLK) or (ACKN and ACLL and ADRN)
ACKM*DFIRST END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACKMDAW)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
IF STYLE/REPLY CODE(s) G3, G4, G5 OR G6 WERE ENTERED FOR MRC ACKN, YOU MUST ANSWER MRC (ACKP and ACKQ)
IF STYLE/REPLY CODE(s) G7, G8 OR G9 WERE ENTERED FOR MRC ACKN, YOU MUST ANSWER MRC (ACKR and ACKS)
ACKN*LFIRST END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACKNLE1)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAT |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
| AAU1449 | G3 | RAISED |
| AAU1450 | G4 | RAISED |
| AAU1451 | G5 | RAISED |
| AAU1452 | G6 | SWIVEL FLANGE RAISED |
| AAU1453 | G7 | RECESSED W/GASKET GROOVE |
| AAU1454 | G8 | RECESSED |
| AAU1455 | G9 | RECESSED |
ACKP*JFIRST END RAISED FACE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKPJAB2.0*;ACKPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKQ*JFIRST END RAISED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKQJAB2.0*;ACKQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKR*JFIRST END RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKRJAA2.0*;ACKRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKS*JFIRST END RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKSJAB2.0*;ACKSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKY and ACLA and ACLB and ACKZ)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (AAHF and ACKU and ACLA and ACLB and ACKZ)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW and ACLA and AFLN and AFLS and ACKZ)
IF STYLE/REPLY CODE(s) 1A OR 2A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKY)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (AAHF and ACKU)
IF STYLE/REPLY CODE(s) 4A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW)
IF STYLE/REPLY CODE(s) 6A WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKU and ACKV and ACKW and ACKX)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKZ and ACKU and ACKV and ACKW and ACLA and ACLB)
IF STYLE/REPLY CODE(s) 6 WERE ENTERED FOR MRC ACKT, YOU MUST ANSWER MRC (ACKZ and ACKU and ACKV and ACKX and ACLA and ACLB)
ACKT*LFIRST END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACKTL2)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02898 | 1 | HEXAGON W/ BOLT HOLES |
| DR02899 | 1A | HEXAGON |
| DR02906 | 2 | OCTAGON W/ BOLT HOLES |
| DR02907 | 2A | OCTAGON |
| DR02914 | 3 | ROUND W/ BOLT HOLES |
| DR02915 | 3A | ROUND |
| DR02922 | 4 | RECTANGULAR (INCLUDES SQUARE) W/ BOLT HOLES |
| DR02923 | 4A | RECTANGULAR (INCLUDES SQUARE) |
| DR02924 | 5 | TRIANGULAR W/ BOLT HOLES |
| DR02925 | 5A | TRIANGULAR |
| DR02932 | 6 | OVAL W/ BOLT HOLES |
| DR02933 | 6A | OVAL |
ACKZ*AFIRST END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACKZA10*)
AAHF*JFIRST END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHFJAB2.0*;AAHFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKU*JFIRST END FLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE FIRST END FLANGE, IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKUJAB2.0*;ACKUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKV*JFIRST END FLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE FIRST END FLANGE, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKVJAC2.0*;ACKVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKW*JFIRST END FLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE FIRST END FLANGE, IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKWJAB2.0*;ACKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKX*JFIRST END FLANGE END RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKXJAB2.0*;ACKXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKY*JFIRST END WIDTH ACROSS FLATS
THE DISTANCE FROM ONE FLAT TO THE OPPOSITE FLAT OF THE FIRST END.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACKYJAA2.0*;ACKYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLA*JFIRST END BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLAJAA2.0*;ACLAJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLB*JFIRST END BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLBJAA2.0*;ACLBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLN*JFIRST END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLNJAC2.0*;AFLNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLS*JFIRST END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLSJAB2.0*;AFLSJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLE*JFIRST END INSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLEJAA2.0*;ACLEJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLF*JFIRST END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLFJAA2.0*;ACLFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLG*JFIRST END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLGJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACLH*JFIRST END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLHJAA2.0*;ACLHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLK*AFIRST END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACLKAU8)
ADRN*JFIRST END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRNJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACLL*DFIRST END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACLLDR*;ACLLDL$DL*;ACLLDL$$DL*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTE*BFIRST END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTEB2.0)
ACTK*JFIRST END SEAT RADIUS
THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACTKJAC2.0*;ACTKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) F WERE ENTERED FOR MRC ACLR, YOU MUST ANSWER MRC (ACLS)
ACLR*DSECOND END RELATIONSHIP WITH FIRST END
INDICATES WHETHER OR NOT THE SECOND END IS IDENTICAL TO THE FIRST END. PLEASE USE MRC CQBB IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACLRDF)
| Table 1 |
| Reply Code (AB78) | Reply |
| B | IDENTICAL |
| F | NOT IDENTICAL |
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMP and ACMS and ACMR) or (ACLT and ACMP and ACMS and ADRP)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMP)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMS)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMN)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACLY)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACML and ADRP and ACMS)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACML and ACMM)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMM and ADRP and ACMS)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMM)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ADRP and ACMS)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACLS, YOU MUST ANSWER MRC (ACLT and ACMS and ACMR) or (ACLT and ACMS and ADRP)
ACLS*DSECOND END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACLSDWY)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
IF STYLE/REPLY CODE(s) G3, G4, G5 OR G6 WERE ENTERED FOR MRC ACLT, YOU MUST ANSWER MRC (ACLU and ACLV)
IF STYLE/REPLY CODE(s) G7, G8 OR G9 WERE ENTERED FOR MRC ACLT, YOU MUST ANSWER MRC (ACLW and ACLX)
ACLT*LSECOND END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACLTLE8)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAL |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
| AAU1449 | G3 | RAISED |
| AAU1450 | G4 | RAISED |
| AAU1451 | G5 | RAISED |
| AAU1452 | G6 | SWIVEL FLANGE RAISED |
| AAU1453 | G7 | RECESSED W/GASKET GROOVE |
| AAU1454 | G8 | RECESSED |
| AAU1455 | G9 | RECESSED |
ACLU*JSECOND END RAISED FACE HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLUJAA2.0*;ACLUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLV*JSECOND END RAISED FACE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLVJAA2.0*;ACLVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLW*JSECOND END RECESS DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLWJAA2.0*;ACLWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLX*JSECOND END RECESS DEPTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLXJAA2.0*;ACLXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) 1 OR 2 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMD and ACMG and ACMH and ACMF)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (AAHV and ACLZ and ACMG and ACMH and ACMF)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMA and ACMB and ACMG and AFLP and AFLT and ACMF)
IF STYLE/REPLY CODE(s) 1A OR 2A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMD)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (AAHV and ACLZ)
IF STYLE/REPLY CODE(s) 4A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMA and ACMB)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACLZ and ACMA and ACMB)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ACLY, YOU MUST ANSWER MRC (ACMF and ACLZ and ACMA and ACMB and ACMG and ACMH)
ACLY*LSECOND END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACLYL4A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02898 | 1 | HEXAGON W/ BOLT HOLES |
| DR02899 | 1A | HEXAGON |
| DR02906 | 2 | OCTAGON W/ BOLT HOLES |
| DR02907 | 2A | OCTAGON |
| DR02914 | 3 | ROUND W/ BOLT HOLES |
| DR02915 | 3A | ROUND |
| DR02923 | 4 | RECTANGULAR (INCLUDES SQUARE) W/ BOLT HOLES |
| DR02922 | 4A | RECTANGULAR (INCLUDES SQUARE) |
| DR02924 | 5 | TRIANGULAR W/ BOLT HOLES |
| DR02925 | 5A | TRIANGULAR |
ACMF*ASECOND END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACMFA10*)
AAHV*JSECOND END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAHVJAB2.0*;AAHVJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACLZ*JSECOND END FLANGE THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF THE SECOND END FLANGE, IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACLZJAA2.0*;ACLZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMA*JSECOND END FLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SECOND END FLANGE, IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMAJAC2.0*;ACMAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMB*JSECOND END FLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE SECOND END FLANGE, IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMBJAA2.0*;ACMBJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMD*JSECOND END WIDTH ACROSS FLATS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMDJAB2.0*;ACMDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMG*JSECOND END BOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMGJAA2.0*;ACMGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMH*JSECOND END BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMHJAA2.0*;ACMHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLP*JSECOND END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLPJAA2.0*;AFLPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLT*JSECOND END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLTJAA2.0*;AFLTJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMLJSECOND END INSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE INSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMLJAC2.0*;ACMLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMM*JSECOND END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMMJAA2.0*;ACMMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMN*JSECOND END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMNJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACMP*JSECOND END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACMPJAB2.0*;ACMPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACMR*ASECOND END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACMRAS5)
ADRP*JSECOND END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRPJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACMS*DSECOND END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION.
Enter the applicable reply code from the table below
(ACMSDR*;ACMSDL$DR*;ACMSDL$$DR*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTF*BSECOND END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CRCN OR CQRB WITH USE OF ISAC IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTFB2.0)
ACTL*JSECOND END SEAT RADIUS
THE RADIUS OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACTLJAC2.0*;ACTLJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) G WERE ENTERED FOR MRC ACMX, YOU MUST ANSWER MRC (ACMY)
ACMX*DTHIRD END RELATIONSHIP WITH PRECEDING ENDS
INDICATES WHETHER OR NOT THE THIRD END IS IDENTICAL WITH FIRST OR SECOND END.
Enter the applicable reply code from the table below
(ACMXDC)
| Table 1 |
| Reply Code (AB78) | Reply |
| C | IDENTICAL WITH FIRST END |
| D | IDENTICAL WITH SECOND END |
| G | NOT IDENTICAL WITH FIRST OR SECOND END |
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNW and ACNZ and ACNY) or (ACMZ and ACNW and ACNZ and ADRQ)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNW)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNZ)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNV)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNF)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ADRQ and ACNZ)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNU)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNU and ADRQ and ACNZ)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNU)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ADRQ and ACNZ)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACMY, YOU MUST ANSWER MRC (ACMZ and ACNZ and ACNY) or (ACMZ and ACNZ and ADRQ)
ACMY*DTHIRD END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACMYDAB)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
ACMZ*LTHIRD END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACMZLE5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAL |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMPRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
| AAU1449 | G3 | RAISED |
| AAU1450 | G4 | RAISED |
| AAU1451 | G5 | RAISED |
| AAU1452 | G6 | SWIVEL FLANGE RAISED |
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNG and ACNH and ACNP and ACNQ and ACNN)
IF STYLE/REPLY CODE(s) 4 WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK and ACNP and AFLQ and AFLU and ACNN)
IF STYLE/REPLY CODE(s) 3A WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNG and ACNH)
IF STYLE/REPLY CODE(s) 4A WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK)
IF STYLE/REPLY CODE(s) 5A WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK)
IF STYLE/REPLY CODE(s) 5 WERE ENTERED FOR MRC ACNF, YOU MUST ANSWER MRC (ACNH and ACNK and ACNP and ACNQ)
ACNF*LTHIRD END FLANGE SHAPE STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE SHAPE OF THE END FLANGE.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACNFL5A)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| DR02899 | 1A | HEXAGON |
| DR02907 | 2A | OCTAGON |
| DR02914 | 3 | ROUND W/ BOLT HOLES |
| DR02915 | 3A | ROUND |
| DR02922 | 4 | RECTANGULAR (INCLUDES SQUARE) W/ BOLT HOLES |
| DR02923 | 4A | RECTANGULAR (INCLUDES SQUARE) |
| DR02924 | 5 | TRIANGULAR W/ BOLT HOLES |
| DR02925 | 5A | TRIANGULAR |
ACNN*ATHIRD END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACNNA10*)
ACNG*JTHIRD END FLANGE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNGJAB2.0*;ACNGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNH*JTHIRD END FLANGE THICKNESS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNHJAA2.0*;ACNHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNK*JTHIRD END FLANGE WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNKJAB2.0*;ACNKJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNP*JTHIRD END BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNPJAA2.0*;ACNPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNQ*JTHIRD END BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNQJAA2.0*;ACNQJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLQ*JTHIRD END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLQJAC2.0*;AFLQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLU*JTHIRD END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLUJAA2.0*;AFLUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNU*JTHIRD END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNUJAA2.0*;ACNUJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNV*JTHIRD END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNVJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACNW*JTHIRD END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACNWJAC2.0*;ACNWJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACNY*ATHIRD END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACNYAF3)
ADRQ*JTHIRD END THREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(ADRQJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACNZ*DTHIRD END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. PLEASE USE MRC AAJF WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACNZDR*;ACNZDL$DR*;ACNZDL$$DR*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTG*BTHIRD END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTGB2.0)
IF STYLE/REPLY CODE(s) H WERE ENTERED FOR MRC ACPE, YOU MUST ANSWER MRC (ACPF)
ACPE*DFOURTH END RELATIONSHIP WITH PRECEDING ENDS
INDICATES WHETHER OR NOT THE FOURTH END IS IDENTICAL WITH THE FIRST,SECOND,OR THIRD END.
Enter the applicable reply code from the table below
(ACPEDH)
| Table 1 |
| Reply Code (AB78) | Reply |
| C | IDENTICAL WITH FIRST END |
| D | IDENTICAL WITH SECOND END |
| E | IDENTICAL WITH THIRD END |
| H | NOT IDENTICAL WITH FIRST, SECOND OR THIRD END |
IF STYLE/REPLY CODE(s) AA OR AC WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQC and ACQF and ACQE) or (ACPG and ACQC and ACQF)
IF STYLE/REPLY CODE(s) AB, AD OR BE WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQC)
IF STYLE/REPLY CODE(s) AE, AG OR AH WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF)
IF STYLE/REPLY CODE(s) AF, AJ OR BD WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQB)
IF STYLE/REPLY CODE(s) AK, AL OR AM WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG)
IF STYLE/REPLY CODE(s) AP WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF)
IF STYLE/REPLY CODE(s) AQ WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQA)
IF STYLE/REPLY CODE(s) AR WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQA)
IF STYLE/REPLY CODE(s) AS WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQA)
IF STYLE/REPLY CODE(s) AT OR AU WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF)
IF STYLE/REPLY CODE(s) AV OR AW WERE ENTERED FOR MRC ACPF, YOU MUST ANSWER MRC (ACPG and ACQF and ACQE) or (ACPG and ACQF)
ACPF*DFOURTH END CONNECTION TYPE
A NARRATIVE DESCRIPTION OF THE TYPE OF END CONNECTION.
Enter the applicable reply code from the table below
(ACPFDAD)
| Table 1 |
| Reply Code (AB76) | Reply |
| BD | BUTT WELD PIPE |
| BE | BUTT WELD TUBE |
| AM | PLAIN FACE FLANGE |
| AL | RAISED FACE FLANGE |
| AK | RECESSED FLANGE |
| WY | THREADED CARTRIDGE |
| AH | THREADED EXTERNAL AND INTERNAL PIPE |
| AW | THREADED EXTERNAL BOSS |
| AU | THREADED EXTERNAL GAS CYLINDER |
| AR | THREADED EXTERNAL HOSE |
| AG | THREADED EXTERNAL PIPE |
| AC | THREADED EXTERNAL TUBE |
| AV | THREADED INTERNAL BOSS |
| AT | THREADED INTERNAL GAS CYLINDER |
| AP | THREADED INTERNAL HOSE |
| AE | THREADED INTERNAL PIPE |
| AA | THREADED INTERNAL TUBE |
| WZ | UNTHREADED CARTRIDGE |
| AS | UNTHREADED EXTERNAL HOSE |
| AJ | UNTHREADED EXTERNAL PIPE |
| AD | UNTHREADED EXTERNAL TUBE |
| AQ | UNTHREADED INTERNAL HOSE |
| AF | UNTHREADED INTERNAL PIPE |
| AB | UNTHREADED INTERNAL TUBE |
ACPG*LFOURTH END STYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE END.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(ACPGLD5)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1389 | B1 | SWIVEL NUT, FLARE |
| AAU1398 | B10 | SWIVEL NUT, GAS |
| AAU1399 | B11 | PLAIN |
| AAU1400 | B12 | OPTIONAL END |
| AAU1401 | B13 | INVERTED FLARE |
| AAU1402 | B14 | GASKET SEAT |
| AAU1403 | B15 | DOUBLE COMPRESSION |
| AAU1404 | B16 | SWIVEL NUT, GASKET SEAL |
| AAU1405 | B17 | HIGH PRESSURE FLARE (USED WITH MALE THREADED STYLE NO. 39) |
| AAU1390 | B2 | SWIVEL NUT, INVERTED FLARE |
| AAU1391 | B3 | SWIVEL NUT, FLARE |
| AAU1392 | B4 | SWIVEL NUT, GASKET SEAL |
| AAU1393 | B5 | SWIVEL NUT, GASKET SEAL |
| AAU1394 | B6 | GASKET SEAL |
| AAU1395 | B7 | FLARE |
| AAU1396 | B8 | SWIVEL NUT, COMPRESSION |
| AAU1397 | B9 | SWIVEL NUT, FLARELESS |
| AAU1406 | C1 | SOCKET |
| AAU1415 | C10 | HOSE SOCKET |
| AAU1416 | C11 | SOCKET W/BRAZING RING |
| AAU1417 | C12 | GASKET SEAL |
| AAU1418 | C13 | BELL |
| AAU1419 | C14 | DRESSER TYPE |
| AAU1420 | C15 | DRESSER TYPE |
| AAU1407 | C2 | STREAMLINED WITH ONE BRAZING RING |
| AAU1408 | C3 | STREAMLINED WITH TWO BRAZING RINGS |
| AAU1409 | C4 | REDUCED SOCKET |
| AAU1410 | C5 | REDUCED SOCKET WITH ONE BRAZING RING |
| AAU1411 | C6 | REDUCED GASKET SEAL |
| AAU1412 | C7 | PLAIN |
| AAU1413 | C8 | CRIMPED |
| AAU1414 | C9 | GROOVED INSIDE |
| AAU1421 | D1 | GASKET SEAL COMPRESSION |
| AAU1430 | D10 | EXTERNAL SEAT FOR GASKET SEAL |
| AAU1431 | D11 | SWIVEL NUT, FLARED |
| AAU1432 | D12 | SWIVEL NUT, DOUBLE COMPRESSION |
| AAU1433 | D13 | DOUBLE THREADED SECTION BOSS FITTING GASKET WITH LOCKNUT SEALING |
| AAU1422 | D2 | INVERTED FLARE |
| AAU1423 | D3 | FLARED |
| AAU1424 | D4 | COMPRESSION |
| AAU1425 | D5 | FLARELESS |
| AAU1426 | D6 | PLAIN |
| AAU1427 | D7 | SWIVEL NUT INVERTED FLARE |
| AAU1428 | D8 | SWIVEL, PLAIN |
| AAU1429 | D9 | GASKET SEAL |
| AAU1434 | E1 | PLAIN |
| AAU1443 | E10 | KNURLED |
| AAU1435 | E2 | GROOVED |
| AAU1436 | E3 | BEADED |
| AAU1437 | E4 | BEADED |
| AAU1438 | E5 | SPIRALED |
| AAU1439 | E6 | BEVELED |
| AAU1440 | E7 | BARBED OR SERRATED |
| AAU1441 | E8 | MULTI-GROOVED |
| AAU1442 | E9 | MULTI-GROOVED |
| AAU1444 | F1 | BEVELED |
| AAU1445 | F2 | BEVELED |
| AAU1446 | F3 | BEVELED |
| AAU1447 | G1 | PLAIN |
| AAU1448 | G2 | SWIVEL FLANGE PLAIN |
ACPU*AFOURTH END BOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(ACPUA10*)
ACPV*JFOURTH END BOLT HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACPVJAC2.0*;ACPVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLR*JFOURTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLRJAA2.0*;AFLRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFLV*JFOURTH END CENTER TO CENTER DISTANCE BETWEEN HOLES ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFLVJAA2.0*;AFLVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACQA*JFOURTH END OUTSIDE DIAMETER HOSE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED HOSE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACQAJAC2.0*;ACQAJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACQB*JFOURTH END NOMINAL PIPE SIZE ACCOMMODATED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF THE PIPE THE END WILL ACCOMMODATE.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACQBJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
ACQC*JFOURTH END OUTSIDE DIAMETER TUBE ACCOMMODATED
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE ACCOMMODATED TUBE,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACQCJAB2.0*;ACQCJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACQE*AFOURTH END THREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(ACQEAV4)
ACQF*DFOURTH END THREAD DIRECTION
THE DIRECTION OF THE THREAD WHEN VIEWED AXIALLY. A RIGHT-HAND THREAD WINDS IN A CLOCKWISE DIRECTION WHILE A LEFT-HAND THREAD WINDS IN A COUNTERCLOCKWISE DIRECTION. PLEASE USE MRC AAJF WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACQFDR*;ACQFDL$DL*;ACQFDL$$DL*)
| Table 1 |
| Reply Code (AA38) | Reply |
| L | LEFT-HAND |
| R | RIGHT-HAND |
ACTH*BFOURTH END SEAT ANGLE IN DEG
THE ANGLE OF THE END SURFACE UPON WHICH THE MATED SURFACE SEATS,EXPRESSED IN DEGREES. PLEASE USE MRC CQRB WITH ISAC TABLE 0036 IN PLACE OF THIS DISCONTINUED MRC.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACTHB2.0)
IF STYLE/REPLY CODE(s) A4, A21, A22, A25, A28, A30 OR A31 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ADQR)
IF STYLE/REPLY CODE(s) A6, A14, A15, A16, A17, A26, A27, A29, A35, A36, A37, A38, A41 OR A42 WERE ENTERED FOR MRC AAQL, YOU MUST ANSWER MRC (ACSX)
AAQLLBODY STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE BODY.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AAQLLA44)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAU1343 | A1 | STRAIGHT THRU |
| AAU1352 | A10 | STRAIGHT THRU |
| AAU1353 | A11 | TEE |
| AAU1354 | A12 | ANGLE |
| AAU1355 | A13 | TEE ANGLE |
| AAU1356 | A14 | ANGLE W/OFFSET |
| AAU1357 | A15 | TEE W/OFFSET |
| AAU1358 | A16 | ANGLE W/OFFSET |
| AAU1359 | A17 | TEE W/OFFSET |
| AAU1360 | A18 | STRAIGHT THRU |
| AAU1361 | A19 | CROSS |
| AAU1344 | A2 | TEE |
| AAU1362 | A20 | STRAIGHT THRU |
| AAU1363 | A21 | TEE ANGLE |
| AAU1364 | A22 | TEE |
| AAU1365 | A23 | ANGLE |
| AAU1366 | A24 | ANGLE |
| AAU1367 | A25 | ANGLE |
| AAU1368 | A26 | TEE ANGLE W/OFFSET |
| AAU1369 | A27 | TEE W/OFFSET |
| AAU1370 | A28 | ANGLE |
| AAU1371 | A29 | TEE W/OFFSET |
| AAU1345 | A3 | CROSS |
| AAU1372 | A30 | STRAIGHT THRU |
| AAU1373 | A31 | STRAIGHT THRU |
| AAU1374 | A32 | STRAIGHT THRU |
| AAU1375 | A33 | STRAIGHT THRU |
| AAU1376 | A34 | TEE W/OFFSET |
| AAU1377 | A35 | ANGLE W/OFFSET |
| AAU1378 | A36 | ANGLE W/OFFSET |
| AAU1379 | A37 | ANGLE W/OFFSET |
| AAU1380 | A38 | ANGLE W/OFFSET |
| AAU1381 | A39 | ANGLE |
| AAU1346 | A4 | STRAIGHT THRU |
| AAU1382 | A40 | ANGLE W/OFFSET |
| AAU1383 | A41 | TEE W/OFFSET |
| AAU1384 | A42 | ANGLE W/OFFSET |
| AAU1385 | A43 | STRAIGHT THRU |
| AAU1386 | A44 | ANGLE |
| AAU1387 | A45 | SCREW-IN CARTRIDGE |
| AAU1388 | A46 | DROP-IN CARTRIDGE |
| AAU1347 | A5 | Y ANGLE |
| AAU1348 | A6 | STRAIGHT THRU W/OFFSET |
| AAU1349 | A7 | ANGLE |
| AAU1350 | A8 | STRAIGHT THRU Y |
| AAU1351 | A9 | Y ANGLE |
ADQL*JFACE TO FACE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQLJAB2.0*;ADQLJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQM*JFIRST CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQMJAC2.0*;ADQMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQN*JSECOND CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQNJAB2.0*;ADQNJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQP*JTHIRD CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQPJAC2.0*;ADQPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQQ*JFOURTH CONNECTION FACE TO CENTERLINE DISTANCE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQQJAC2.0*;ADQQJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADQR*JCENTER TO CENTER DISTANCE
THE CENTER TO CENTER DISTANCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADQRJAC2.0*;ADQRJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACSX*JOFFSET DISTANCE
THE DISTANCE OF OFFSET IN THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACSXJAB2.0*;ACSXJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACKL*DMEDIA FOR WHICH DESIGNED
THE TYPE OF SERVICE WITH WHICH THE ITEM IS DESIGNED TO BE USED. PLEASE USE MRC MEDA IN PLACE OF THIS DISCONTINUED MRC.
Enter the applicable reply code from the table below
(ACKLDAGQ*;ACKLDAR$DED*;ACKLDAR$$DED*)
| Table 1 |
| Reply Code (AB75) | Reply |
| AA | ACETYLENE |
| AB | AIR |
| AAJC | AIR, OIL PUMPED |
| AAJH | AIR, WATER PUMPED |
| AD | ALCOHOL, ETHYL |
| AE | ALCOHOL, METHYL |
| AG | AMMONIA, GASEOUS |
| AH | AMMONIA, LIQUID |
| AJ | ARGON |
| AAJD | ARGON, OIL PUMPED |
| AK | BROMOCHLOROMETHANE |
| AR | BUTANE |
| AS | CARBON DIOXIDE |
| DW | CARBON MONOXIDE |
| AT | CARBON TETRACHLORIDE |
| AV | CHLORINE |
| AAHT | DEUTERIUM |
| AACL | DICHLORODIFLUOROMETHANE |
| AGP | DIFLUOROMETHANE |
| AAHV | ETHANE |
| BB | ETHYLENE GLYCOL |
| ED | ETHYLENE OXIDE |
| AAHW | ETHYLENE, INDUSTRIAL |
| AAHX | ETHYLENE, MEDICAL |
| AAJF | FLUID, PETROLEUM BASE |
| AFE | FREON 12 USE REFRIGERANT R-12 |
| ADC | FREON USE REFRIGERANT |
| BD | GAS |
| AAJA | GAS, NONCORROSIVE |
| AADF | GENERAL |
| BL | HELIUM |
| AAJE | HELIUM, OIL PUMPED |
| AAHY | HEXAFLUOROETHANE |
| AAGJ | HYDRAULIC FLUID, MIL-H-5606 |
| AAGD | HYDRAULIC FLUID, PETROLEUM BASE |
| BN | HYDRAULIC FLUID, PHOSPHATE-ESTER BASE |
| BP | HYDRAULIC FLUID, SILICATE-ESTER BASE |
| BM | HYDRAULIC OIL |
| BQ | HYDRAZINE |
| BR | HYDRAZINE/UNSYMMETRIC DIMETHYL HYDRAZINE, 50/50- UDMH |
| BS | HYDROCARBON FUELS AND OILS |
| BT | HYDROGEN |
| BU | INGESTED LIQUIDS |
| NM | LIQUEFIED PETROLEUM GAS |
| GT | LIQUID, NONCORROSIVE |
| CD | LUBRICATING OIL, DIESTER BASE |
| AAJB | METHANE |
| HP | MONOCHLORODIFLUOROMETHANE |
| AADW | NATURAL GAS |
| CF | NITRIC ACID |
| CH | NITROGEN, GASEOUS |
| CJ | NITROGEN, LIQUID |
| AAHR | NITROGEN, OIL PUMPED |
| AAHS | NITROGEN, WATER PUMPED |
| AAEL | NITROUS OXIDE |
| AGQ | NONCORROSIVE FLUID |
| CL | OIL |
| CN | OXYGEN, GASEOUS |
| CP | OXYGEN, LIQUID |
| AGR | PETROLEUM BASE FLUID |
| CQ | PROPANE |
| AAW | REFRIGERANT R-22 |
| AAJG | REFRIGERANT, NONCORROSIVE |
| DC | STEAM |
| DD | SULPHUR DIOXIDE, GASEOUS |
| ABA | SULPHUR HEXAFLUORIDE |
| ET | SULPHUR HEXAFLUORIDE |
| DE | TRICHLORETHYLENE |
| DF | WATER |
| DH | WATER, FRESH |
| DK | WATER, OIL OR GAS |
| DL | WATER, SALT |
ADZJ*DMOUNTING FACILITY
THE MEANS OTHER THAN THE END CONNECTION/S/ BY WHICH THE ITEM MAY BE MOUNTED.
Enter the applicable reply code from the table below
(ADZJDJ*;ADZJDG$DF*;ADZJDG$$DF*)
| Table 1 |
| Reply Code (AC70) | Reply |
| K | BOLTS |
| F | BRACKET |
| B | CLAMP |
| H | EXTERNAL THREAD |
| G | FLANGE |
| J | INTERNAL THREAD |
| D | LUG |
| E | PANEL |
| L | STUD |
ADZH*DRENEWABLE SEAT RING TYPE
INDICATES THE TYPE OF RENEWABLE SEATING RING IN THE ITEM.
Enter the applicable reply code from the table below
(ADZHDAL*;ADZHDAC$DAE*;ADZHDAC$$DAE*)
| Table 1 |
| Reply Code (AC69) | Reply |
| A | ANY ACCEPTABLE |
| AA | BOLTED |
| AB | BONDED |
| AC | PRESSED-IN |
| AL | RETAINING RING |
| AD | RETAINING SCREW |
| AE | THREADED |
| AF | WELDED |
AEVNDREGULATION TYPE
INDICATES THE BASIC DESIGN TYPE USED FOR REGULATING THE ITEM.
Enter the applicable reply code from the table below
(AEVNDK*;AEVNDF$DE*;AEVNDF$$DE*)
| Table 1 |
| Reply Code (AD45) | Reply |
| E | 1ST STAGE AUTOMATIC, 2ND STAGE MANUAL |
| F | 1ST STAGE MANUAL, 2ND STAGE AUTOMATIC |
| C | AUTOMATIC DOUBLE STAGE |
| B | AUTOMATIC SINGLE STAGE |
| D | MANUAL SINGLE STAGE |
| K | MANUAL, DOUBLE STAGE |
AEVP*DMANUAL CONTROL METHOD
THE MEANS USED TO MANUALLY ADJUST THE ITEM.
Enter the applicable reply code from the table below
(AEVPDAT*;AEVPDAV$DAU*;AEVPDAV$$DAU*)
| Table 1 |
| Reply Code (AC58) | Reply |
| BK | KNOB |
| AH | LEVER |
| AAJR | LEVER W/WEIGHTS |
| AU | SCREW |
| AR | TEE HANDLE |
| AV | WHEEL |
| AT | WRENCH |
AEVQ*DVALVE STEM DESIGN
THE SEAT DESIGN OF THE VALVE STEM.
Enter the applicable reply code from the table below
(AEVQDB*;AEVQDC$DC*)
| Table 1 |
| Reply Code (AD46) | Reply |
| B | DOUBLE SEAT |
| C | SINGLE SEAT |
AEVRDVALVE LOADING METHOD
THE MEANS OF PROVIDING RESISTANCE TO THE MEDIA PASSING THROUGH A VALVE,WHEREBY THE VALVE IS ACTUATED TO REGULATE THE FLOW.
Enter the applicable reply code from the table below
(AEVRDC*;AEVRDF$DD*;AEVRDF$$DD*)
| Table 1 |
| Reply Code (AC63) | Reply |
| F | BELLOWS |
| D | DOME |
| B | SPRING |
| C | WEIGHT |
AEVS*DREMOTE ACTUATION METHOD
THE MEANS WHEREBY A VALVE IS ACTUATED OTHER THAN BY THE MEDIA PASSING THROUGH IT.
Enter the applicable reply code from the table below
(AEVSDL*;AEVSDJ$DB*;AEVSDJ$$DB*)
| Table 1 |
| Reply Code (AD04) | Reply |
| J | BELLOWS |
| B | DIAPHRAGM |
| D | PISTON |
| K | SOLENOID |
| L | SPOOL |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information