An item consisting of an inductance and a resistance normally in parallel. The inductance is usually wound around the resistor. Half of the turns may be wound to inductively oppose the other half. It is designed to be inserted in the circuit of a radio frequency stage to suppress high frequency parasitic oscillations. For items designed to widen the band width, or amplify a portion of the band in an amplifier circuit, see COIL, RADIO FREQUENCY.
ISAC Reply 3AEE added to MRC AKDX.
ISAC Reply 3EDH added to MRC AKDX.
ISAC Reply 3EDI added to MRC AKDX.
ISAC Reply 3HOU added to MRC AKDX.
ISAC Reply 1A deleted from MRC AKDX.
ISAC Reply 1B deleted from MRC AKDX.
ISAC Reply 1C deleted from MRC AKDX.
ISAC Reply 1D deleted from MRC AKDX.
ISAC Reply 1E deleted from MRC AKDX.
ISAC Reply 1F deleted from MRC AKDX.
ISAC Reply 1G deleted from MRC AKDX.
ISAC Reply 1H deleted from MRC AKDX.
ISAC Reply 1X deleted from MRC AKDX.
ISAC Reply 1Z deleted from MRC AKDX.
ISAC Reply 3AEE added to MRC BKPL.
ISAC Reply 3EAW added to MRC BKPL.
ISAC Reply 3EAX added to MRC BKPL.
ISAC Reply 3EBA added to MRC BKPL.
ISAC Reply 3EBH added to MRC BKPL.
ISAC Reply 3ECN added to MRC BKPL.
ISAC Reply 3ECT added to MRC BKPL.
ISAC Reply 3HOU added to MRC BKPL.
ISAC Reply 1A deleted from MRC BKPL.
ISAC Reply 1B deleted from MRC BKPL.
ISAC Reply 1C deleted from MRC BKPL.
ISAC Reply 1D deleted from MRC BKPL.
ISAC Reply 1E deleted from MRC BKPL.
ISAC Reply 1F deleted from MRC BKPL.
ISAC Reply 1G deleted from MRC BKPL.
ISAC Reply 1H deleted from MRC BKPL.
ISAC Reply 1X deleted from MRC BKPL.
ISAC Reply 1Z deleted from MRC BKPL.
ISAC Reply 1A deleted from MRC BKPL.
ISAC Reply 1B deleted from MRC BKPL.
ISAC Reply 1C deleted from MRC BKPL.
ISAC Reply 1D deleted from MRC BKPL.
ISAC Reply 1E deleted from MRC BKPL.
ISAC Reply 1F deleted from MRC BKPL.
ISAC Reply 1X deleted from MRC BKPL.
ISAC Reply 1Z deleted from MRC BKPL.
ISAC Reply 1A deleted from MRC BKPL.
ISAC Reply 1B deleted from MRC BKPL.
ISAC Reply 1C deleted from MRC BKPL.
ISAC Reply 1D deleted from MRC BKPL.
ISAC Reply 1E deleted from MRC BKPL.
ISAC Reply 1F deleted from MRC BKPL.
ISAC Reply 1G deleted from MRC BKPL.
ISAC Reply 3AEE added to MRC ABHY.
ISAC Reply 3EAW added to MRC ABHY.
ISAC Reply 3EBA added to MRC ABHY.
ISAC Reply 3EBH added to MRC ABHY.
ISAC Reply 3ECR added to MRC ABHY.
ISAC Reply 3ECT added to MRC ABHY.
ISAC Reply 3ECV added to MRC ABHY.
ISAC Reply 3HOU added to MRC ABHY.
ISAC Reply 1A deleted from MRC ABHY.
ISAC Reply 1B deleted from MRC ABHY.
ISAC Reply 1C deleted from MRC ABHY.
ISAC Reply 1D deleted from MRC ABHY.
ISAC Reply 1E deleted from MRC ABHY.
ISAC Reply 1F deleted from MRC ABHY.
ISAC Reply 1G deleted from MRC ABHY.
ISAC Reply 1H deleted from MRC ABHY.
ISAC Reply 1X deleted from MRC ABHY.
ISAC Reply 1Z deleted from MRC ABHY.
ISAC Reply 1A deleted from MRC ABHY.
ISAC Reply 1B deleted from MRC ABHY.
ISAC Reply 1C deleted from MRC ABHY.
ISAC Reply 1D deleted from MRC ABHY.
ISAC Reply 1E deleted from MRC ABHY.
ISAC Reply 1F deleted from MRC ABHY.
ISAC Reply 1X deleted from MRC ABHY.
ISAC Reply 1Z deleted from MRC ABHY.
ISAC Reply 1A deleted from MRC ABHY.
ISAC Reply 1B deleted from MRC ABHY.
ISAC Reply 1C deleted from MRC ABHY.
ISAC Reply 1D deleted from MRC ABHY.
ISAC Reply 1E deleted from MRC ABHY.
ISAC Reply 1F deleted from MRC ABHY.
ISAC Reply 1G deleted from MRC ABHY.
ISAC Reply 3AEE added to MRC CQPZ.
ISAC Reply 3EAW added to MRC CQPZ.
ISAC Reply 3EBA added to MRC CQPZ.
ISAC Reply 3EBH added to MRC CQPZ.
ISAC Reply 3HOU added to MRC CQPZ.
ISAC Reply 1A deleted from MRC CQPZ.
ISAC Reply 1B deleted from MRC CQPZ.
ISAC Reply 1C deleted from MRC CQPZ.
ISAC Reply 1D deleted from MRC CQPZ.
ISAC Reply 1E deleted from MRC CQPZ.
ISAC Reply 1F deleted from MRC CQPZ.
ISAC Reply 1G deleted from MRC CQPZ.
ISAC Reply 1H deleted from MRC CQPZ.
ISAC Reply 1X deleted from MRC CQPZ.
ISAC Reply 1Z deleted from MRC CQPZ.
ISAC Reply 1A deleted from MRC CQPZ.
ISAC Reply 1B deleted from MRC CQPZ.
ISAC Reply 1C deleted from MRC CQPZ.
ISAC Reply 1D deleted from MRC CQPZ.
ISAC Reply 1E deleted from MRC CQPZ.
ISAC Reply 1F deleted from MRC CQPZ.
ISAC Reply 1X deleted from MRC CQPZ.
ISAC Reply 1Z deleted from MRC CQPZ.
ISAC Reply 1A deleted from MRC CQPZ.
ISAC Reply 1B deleted from MRC CQPZ.
ISAC Reply 1C deleted from MRC CQPZ.
ISAC Reply 1D deleted from MRC CQPZ.
ISAC Reply 1E deleted from MRC CQPZ.
ISAC Reply 1F deleted from MRC CQPZ.
ISAC Reply 1G deleted from MRC CQPZ.
ISAC Reply 3AEE added to MRC ACYV.
ISAC Reply 3EAW added to MRC ACYV.
ISAC Reply 3EBA added to MRC ACYV.
ISAC Reply 3EBH added to MRC ACYV.
ISAC Reply 3HOU added to MRC ACYV.
ISAC Reply 1A deleted from MRC ACYV.
ISAC Reply 1B deleted from MRC ACYV.
ISAC Reply 1C deleted from MRC ACYV.
ISAC Reply 1D deleted from MRC ACYV.
ISAC Reply 1E deleted from MRC ACYV.
ISAC Reply 1F deleted from MRC ACYV.
ISAC Reply 1G deleted from MRC ACYV.
ISAC Reply 1H deleted from MRC ACYV.
ISAC Reply 1X deleted from MRC ACYV.
ISAC Reply 1Z deleted from MRC ACYV.
ISAC Reply 1A deleted from MRC ACYV.
ISAC Reply 1B deleted from MRC ACYV.
ISAC Reply 1C deleted from MRC ACYV.
ISAC Reply 1D deleted from MRC ACYV.
ISAC Reply 1E deleted from MRC ACYV.
ISAC Reply 1F deleted from MRC ACYV.
ISAC Reply 1X deleted from MRC ACYV.
ISAC Reply 1Z deleted from MRC ACYV.
ISAC Reply 1A deleted from MRC ACYV.
ISAC Reply 1B deleted from MRC ACYV.
ISAC Reply 1C deleted from MRC ACYV.
ISAC Reply 1D deleted from MRC ACYV.
ISAC Reply 1E deleted from MRC ACYV.
ISAC Reply 1F deleted from MRC ACYV.
ISAC Reply 1G deleted from MRC ACYV.
ISAC Reply 3AEE added to MRC ACZP.
ISAC Reply 3EDH added to MRC ACZP.
ISAC Reply 3EDI added to MRC ACZP.
ISAC Reply 3HOU added to MRC ACZP.
ISAC Reply 1A deleted from MRC ACZP.
ISAC Reply 1B deleted from MRC ACZP.
ISAC Reply 1C deleted from MRC ACZP.
ISAC Reply 1D deleted from MRC ACZP.
ISAC Reply 1E deleted from MRC ACZP.
ISAC Reply 1F deleted from MRC ACZP.
ISAC Reply 1G deleted from MRC ACZP.
ISAC Reply 1H deleted from MRC ACZP.
ISAC Reply 1X deleted from MRC ACZP.
ISAC Reply 1Z deleted from MRC ACZP.
ISAC Reply 3AEE added to MRC AXGY.
ISAC Reply 3EDP added to MRC AXGY.
ISAC Reply 3HOU added to MRC AXGY.
ISAC Reply 1A deleted from MRC AXGY.
ISAC Reply 1B deleted from MRC AXGY.
ISAC Reply 1C deleted from MRC AXGY.
ISAC Reply 1D deleted from MRC AXGY.
ISAC Reply 1X deleted from MRC AXGY.
ISAC Reply 1Z deleted from MRC AXGY.
ISAC Reply 3AEE added to MRC AKPV.
ISAC Reply 3EDJ added to MRC AKPV.
ISAC Reply 3EDL added to MRC AKPV.
ISAC Reply 3EDP added to MRC AKPV.
ISAC Reply 3HOU added to MRC AKPV.
ISAC Reply 1A deleted from MRC AKPV.
ISAC Reply 1B deleted from MRC AKPV.
ISAC Reply 1C deleted from MRC AKPV.
ISAC Reply 1D deleted from MRC AKPV.
ISAC Reply 1X deleted from MRC AKPV.
ISAC Reply 1Z deleted from MRC AKPV.
ISAC Reply 3AEE added to MRC ABTB.
ISAC Reply 3EDP added to MRC ABTB.
ISAC Reply 3HOU added to MRC ABTB.
ISAC Reply 1A deleted from MRC ABTB.
ISAC Reply 1B deleted from MRC ABTB.
ISAC Reply 1C deleted from MRC ABTB.
ISAC Reply 1D deleted from MRC ABTB.
ISAC Reply 1X deleted from MRC ABTB.
ISAC Reply 1Z deleted from MRC ABTB.
ISAC Reply 3AEE added to MRC AEJN.
ISAC Reply 3CVQ added to MRC AEJN.
ISAC Reply 3HOU added to MRC AEJN.
ISAC Reply 1A deleted from MRC AEJN.
ISAC Reply 1B deleted from MRC AEJN.
ISAC Reply 1C deleted from MRC AEJN.
ISAC Reply 1D deleted from MRC AEJN.
ISAC Reply 1X deleted from MRC AEJN.
ISAC Reply 1Z deleted from MRC AEJN.
ISAC Reply 1A deleted from MRC AEJN.
ISAC Reply 1B deleted from MRC AEJN.
ISAC Reply 1C deleted from MRC AEJN.
ISAC Reply 1D deleted from MRC AEJN.
ISAC Reply 1X deleted from MRC AEJN.
ISAC Reply 1Z deleted from MRC AEJN.
ISAC Reply 3AEE added to MRC ABKQ.
ISAC Reply 3CVQ added to MRC ABKQ.
ISAC Reply 3HOU added to MRC ABKQ.
ISAC Reply 1A deleted from MRC ABKQ.
ISAC Reply 1B deleted from MRC ABKQ.
ISAC Reply 1C deleted from MRC ABKQ.
ISAC Reply 1D deleted from MRC ABKQ.
ISAC Reply 1X deleted from MRC ABKQ.
ISAC Reply 1Z deleted from MRC ABKQ.
ISAC Reply 1A deleted from MRC ABKQ.
ISAC Reply 1B deleted from MRC ABKQ.
ISAC Reply 1C deleted from MRC ABKQ.
ISAC Reply 1D deleted from MRC ABKQ.
ISAC Reply 1X deleted from MRC ABKQ.
ISAC Reply 1Z deleted from MRC ABKQ.
MRC ABTD has been deleted
MRC THSD has been deleted
MRC CQJX has been deleted
MRC CMLP has been deleted
MRC ABKR has been deleted
MRC CSQJ has been deleted
MRC CQKH has been deleted
MRC AFFL has been deleted
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED04440*)
AKDXAWINDING QUANTITY
THE NUMBER OF INDIVIDUAL /NOT ELECTRICALLY CONNECTED/ WINDINGS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(AKDX3EDIA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EDH | SINGLE COMPONENT |
| 3EDI | ALL COMPONENTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AKNADINCLOSURE TYPE
INDICATES THE TYPE OF INCLOSURE PROVIDED TO COAT,COVER,PROTECT,OR ENCASE THE ITEM.
Enter the applicable reply code from the table below
(AKNADAF)
| Table 1 |
| Reply Code (AG85) | Reply |
| AH | FULLY INCLOSED |
| AJ | FULLY INCLOSED WITH OIL |
| AD | HERMETICALLY SEALED |
| AK | HERMETICALLY SEALED WITH OIL |
| AE | OPEN |
| AP | PARTIALLY INCLOSED |
| AF | PARTIALLY INCLOSED, DOUBLE SHELL |
| AG | PARTIALLY INCLOSED, HALF SHELL |
TTQYJTERMINAL TYPE AND QUANTITY
INDICATES THE TYPE AND NUMBER OF TERMINALS FOR PROVIDING ELECTRICAL CONNECTION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit.
(TTQYJAAM2*;TTQYJAAM2$$JAAM3*;TTQYJAAM2$JAAM2*)
| Table 1 |
| Reply Code (AN89) | Reply |
| AFZ | BANANA JACK |
| AAB | BANANA PLUG |
| ABL | BINDING POST |
| AAD | BONDING PAD |
| AGA | BUS (BAR) CONDUCTOR |
| AGB | BUSHING |
| AEP | CABLE W/CONNECTOR |
| ABN | CLAMP |
| ADB | CLIP |
| AGC | COLLAR/RING |
| ACT | COMPONENT SOCKET |
| AEB | COMPRESSION |
| ACN | CONNECTOR, PLUG |
| AAF | CONNECTOR, RECEPTACLE |
| AJT | ELECTRON TUBE BASE |
| ABR | EYELET |
| AGD | FEED THRU |
| AAH | FERRULE |
| AGE | FERRULE CLIP |
| AEC | KNIFE BLADE |
| AGF | LINE CORD |
| AGH | PHONE JACK |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| ADA | QUICK DISCONNECT, FEMALE |
| ACZ | QUICK DISCONNECT, MALE |
| AAR | RIBBON |
| ABQ | SCREW |
| AEF | SLOTTED LUG |
| ADC | SNAP-ON, FEMALE |
| ADF | SNAP-ON, MALE |
| AAS | SOLDER STUD |
| AEK | SOLDERLESS LUG |
| AGQ | STANDOFF CLIP |
| AGR | STANDOFF INSULATOR |
| AGS | STANDOFF, SCREW |
| AGT | STANDOFF, SOCKET |
| AAW | STANDOFF, SOLDER LUG |
| AGW | STANDOFF, SOLDERLESS LUG |
| AAY | STANDOFF, THREADED STUD |
| ABA | STANDOFF, WIRE LEAD |
| ABX | TAB W/SCREW |
| ABB | TAB, SOLDER LUG |
| AGX | TERMINAL BLOCK W/SCREWS |
| ABC | THREADED HOLE |
| ABD | THREADED STUD |
| AHA | THUMB SCREW |
| AHB | TIP JACK |
| ACB | TURRET |
| ACM | WIRE HOOK |
| ACC | WIRE LEAD |
| AGY | WIRE LEAD W/CLAMP |
| AEG | WIRE LEAD W/LUG |
| AGZ | WIRE LEAD W/TUBE CAP |
| ACD | WIRE LOOP |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
IF STYLE/REPLY CODE(s) AAH WERE ENTERED FOR MRC BKPL, YOU MUST ANSWER MRC (ABHY and CQPZ)
BKPLDRATING METHOD
THE MEANS BY WHICH THE RATING IS DETERMINED.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(BKPL3EBADAAH*;BKPL3EBADAAH$DAAG*;BKPL3EBADAAH$$DAAG*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EAW | SINGLE COMPONENT SINGLE PRIMARY |
| 3EAX | SINGLE COMPONENT SINGLE PRIMARY INPUT |
| 3EBA | SINGLE COMPONENT SINGLE WINDING |
| 3EBH | SINGLE COMPONENT ALL WINDING |
| 3ECN | ALL COMPONENTS SINGLE PRIMARY |
| 3ECT | ALL COMPONENTS ALL PRIMARY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN29) | Reply |
| AAG | ELECTRICAL |
| AAH | WINDING TURNS |
ABHY*ATURN QUANTITY
THE NUMBER OF TURNS OF CONDUCTIVE MATERIAL FORMING THE WINDING.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(ABHY3EBAAJ6)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EAW | SINGLE COMPONENT SINGLE PRIMARY |
| 3EBA | SINGLE COMPONENT SINGLE WINDING |
| 3EBH | SINGLE COMPONENT ALL WINDING |
| 3ECR | ALL COMPONENTS SINGLE WINDING |
| 3ECT | ALL COMPONENTS ALL PRIMARY |
| 3ECV | ALL COMPONENTS ALL PRIMARY OUTPUT |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CQPZ*JWINDING CONDUCTOR SIZE
THE SIZE OF THE CONDUCTOR WHICH FORMS THE WINDING ON THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQPZ3EAWJAG2.0*;CQPZ3EAWJAG2.0$JAG2.0*;CQPZ3EAWJAG2.0$$JAG2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EAW | SINGLE COMPONENT SINGLE PRIMARY |
| 3EBA | SINGLE COMPONENT SINGLE WINDING |
| 3EBH | SINGLE COMPONENT ALL WINDING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AB96) | Reply |
| F | AMERICAN WIRE GAGE |
| G | MILLIMETER WIRE GAGE |
| H | STANDARD WIRE GAGE |
ACYV*JINDUCTANCE RATING
THE VALUE(S) OF INDUCTANCE INHERENT IN THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACYV3EBAJLC2.0*;ACYV3EBAJLC2.0$JLC2.0*;ACYV3EBAJLC2.0$$JLC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EAW | SINGLE COMPONENT SINGLE PRIMARY |
| 3EBA | SINGLE COMPONENT SINGLE WINDING |
| 3EBH | SINGLE COMPONENT ALL WINDING |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AC31) | Reply |
| H | HENRY |
| U | MICROHENRIES |
| L | MILLIHENRIES |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ACZP*DCOIL FORM TYPE
INDICATES THE TYPE OF SUPPORT ON WHICH THE COIL IS WOUND.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(ACZP3EDHDB*;ACZP3EDHDB$DE*;ACZP3EDHDB$$DE*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EDH | SINGLE COMPONENT |
| 3EDI | ALL COMPONENTS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AC12) | Reply |
| E | AIR WOUND |
| B | HOLLOW |
| D | RESISTOR |
| C | SOLID |
AAPP*JELECTRICAL RESISTANCE
A MEASURE OF THE OPPOSITION TO THE FLOW OF ELECTRICAL CURRENT.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AAPPJQ2.0*)
| Table 1 |
| Reply Code (AA57) | Reply |
| G | GIGOHMS |
| K | KILOHMS |
| M | MEGOHMS |
| Q | OHMS |
ACZQ*BRESISTOR POWER DISSIPATION RATING IN WATTS
THE MAXIMUM AMOUNT OF ELECTRICAL ENERGY THAT CAN BE EXPENDED BY A RESISTOR,EXPRESSED IN WATTS.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ACZQB2.0)
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV)
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV and ABTB)
IF STYLE/REPLY CODE(s) AET OR AHF WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV)
IF STYLE/REPLY CODE(s) ACC WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AFHM)
IF STYLE/REPLY CODE(s) AEW WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AKPV)
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AXGY3AEEDBRZ*;AXGY3AEEDBRZ$DBEF*;AXGY3AEEDBRZ$$DBEF*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EDP | SINGLE GROUP |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AM39) | Reply |
| BDH | ADHESIVE |
| ABC | BRACKET |
| ABD | BUSHING |
| BRZ | CAPTIVE NUT |
| ABH | CLAMP |
| AEC | CLINCH NUT |
| AFL | CLIP |
| AFM | COLLAR |
| ABJ | CORE |
| BSB | EXPANSION PLUG |
| BSC | FERRULE |
| ACR | FLANGE |
| AEY | FOOT |
| ABL | FRICTION |
| BSD | HUB |
| ABP | PLUG-IN |
| BGC | RETAINING RING |
| BEF | SHANK |
| AKC | SLEEVE |
| ABY | SLOT |
| AEF | SOCKET |
| BSF | SPADE LUG |
| AER | SPRING |
| ACB | STRAP |
| ACC | TAB |
| ACD | TERMINAL |
| AES | THREADED BODY |
| AFA | THREADED BUSHING |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| ACQ | UNTHREADED HOLE |
| AEW | UNTHREADED STUD |
| BBP | YOKE |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AKPV*AMOUNTING FACILITY QUANTITY
THE NUMBER OF MOUNTING FACILITIES PROVIDED.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(AKPV3EDJA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EDJ | FIRST GROUP |
| 3EDL | THIRD GROUP |
| 3EDP | SINGLE GROUP |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABTB*JMOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTB3EDPJAB2.0*;ABTB3EDPJAB2.0$JAB2.0*;ABTB3EDPJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3EDP | SINGLE GROUP |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AFHM*JMOUNTING TAB WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A MOUNTING TAB,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFHMJAA2.0*;AFHMJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJN3CVQJAB2.0*;AEJN3CVQJAB2.0$JAB2.0*;AEJN3CVQJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CVQ | SINGLE MOUNTING FACILITY SINGLE CENTER GROUP |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABKQ*JCENTER TO CENTER DISTANCE BETWEEN MOUNTING FACILITIES PARALLEL TO LENGTH
THE DISTANCE BETWEEN THE CENTER OF ONE MOUNTING FACILITY AND THE CENTER OF THE ADJACENT MOUNTING FACILITY PARALLEL TO THE LENGTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKQ3AEEJAB2.0*;ABKQ3AEEJAB2.0$JAB2.0*;ABKQ3AEEJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3CVQ | SINGLE MOUNTING FACILITY SINGLE CENTER GROUP |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAQ*JBODY LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE BODY,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAQJAB2.0*;ADAQJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADAR*JBODY OUTSIDE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BODY,AND TERMINATES AT THE OUTSIDE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADARJAB2.0*;ADARJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADAU*JBODY HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP OF THE BODY,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAUJAB2.0*;ADAUJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADAT*JBODY WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE BODY,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADATJAB2.0*;ADATJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAB2.0*;ABHPJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAC2.0*;ADAVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAA2.0*;ABKWJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAC2.0*;ABMKJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDCND*;CBBLDCNH$$DCNJ*)
| Table 1 |
| Reply Code (AN47) | Reply |
| CNK | COLOR CODED LEAD |
| CNL | COLOR CODED TERMINAL |
| CNH | LEFT HAND WOUND COIL |
| CCS | PROTECTIVE COVER |
| CNJ | RIGHT HAND WOUND COIL |
| FNY | ROHS DIRECTIVE COMPLIANCE |
| BRP | SPECIAL MARKING |
| CAR | TINNED WIRE LEADS |
| CND | W/ARRESTOR |
| CNE | W/CAPACITOR |
| CNF | W/OVERLOAD PROTECTION |
| CNG | W/RECTIFIER |
| BZA | W/RESISTOR |
| AXJ | W/SWITCH |
IF STYLE/REPLY CODE(s) E WERE ENTERED FOR MRC AARG, YOU MUST ANSWER MRC (AARH)
AARG*DRELIABILITY INDICATOR
AN INDICATION THAT THE LEVEL OF PROBABILITY THAT AN ITEM WILL OPERATE WITHOUT FAILURE,AT A SPECIFIED RATED CAPABILITY,AT A SPECIFIED TEMPERATURE,AND FOR A SPECIFIED PERIOD OF TIME,HAS BEEN ESTABLISHED BY TESTING RANDOM SAMPLES OF PRODUCTION LOT.
Enter the applicable reply code from the table below
(AARGDE)
| Table 1 |
| Reply Code (AA61) | Reply |
| E | ESTABLISHED |
| N | NOT ESTABLISHED |
AARH*BRELIABILITY FAILURE RATE LEVEL IN PERCENT
THE RATE OF FAILURE DETERMINED UNDER SPECIFIED CONDITIONS TO ESTABLISH THE RELIABILITY OF AN ITEM,EXPRESSED IN PERCENT.
Enter a reply with a minimum of one digit on either side of the decimal point.
(AARHB2.0)
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
IF STYLE/REPLY CODE(s) BB OR BC WERE ENTERED FOR MRC ENAC, YOU MUST ANSWER MRC (ALAX)
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDBC)
| Table 1 |
| Reply Code (EN02) | Reply |
| GJ | DISTRIBUTION TRANSFORMERS - FEMP-SUSPENDED - ENERGY EFFICIENT PRODUCTS |
| BB | FLUID-FILLED TRANSFORMERS - SYNTHETIC ESTER-BASED - BIOBASED |
| BC | FLUID-FILLED TRANSFORMERS - VEGETABLE OIL-BASED - BIOBASED |
| NR | REVIEWED - DOES NOT MEET SOME ENAC CRITERIA |
ALAX*BBIOBASED CONTENT PERCENTAGE
THE STATED PERCENTAGE OF THE ITEM'S CONTENT THAT IS BIOBASED.
Enter a reply with a minimum of one digit on either side of the decimal point.
(ALAXB2.0)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
AEHZ*JMAXIMUM OPERATING TEMP
THE MAXIMUM TEMPERATURE AT WHICH THE ITEM IS RATED TO OPERATE FOR AN EXTENDED PERIOD OF TIME.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEHZJC2.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
BBRJ*DSPECIAL HANDLING FEATURE
THE UNUSUAL OR UNIQUE CHARACTERISTIC/S/ OR QUALITY/IES/ OF AN ITEM WHICH NECESSITATES THE ESTABLISHMENT OF A REQUIREMENT FOR SPECIAL HANDLING.
Enter the applicable reply code from the table below
(BBRJDAJ*;BBRJDAK$$DAZ*)
| Table 1 |
| Reply Code (AM83) | Reply |
| AJ | HAZARDOUS FOR AIR TRANSPORTATION, REGULATED BY DSAM 4145.3 OR ATARAT-TARIFF-6D |
| AZ | HAZARDOUS-CONTAINS POLYCHLORINATED BIPHENYLS |
| AK | MAGNETIC |
| AQ | PILFERABLE |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDPDA000*;PRMTDRTA000$DAZA000*;PRMTDRTA000$$DAZA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJAUA0002.0*;PMLCJAUA0002.0$JAUA0002.0*;PMLCJAUA0002.0$$JAUA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
ABFE*DHAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION
THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS.
Enter the applicable reply code from the table below
(ABFEDED*;ABFEDFM$$DDN*)
| Table 1 |
| Reply Code (AB27) | Reply |
| AA | ACID RESISTANT |
| BN | AIRTIGHT |
| FG | ALKALI RESISTANT |
| AB | CEMENT TIGHT |
| ED | CORROSION PROOF |
| DJ | CORROSION RESISTANT |
| CG | DRIPPROOF |
| FS | DRIPTIGHT |
| EF | DUST RESISTANT |
| CF | DUSTPROOF |
| DY | DUSTTIGHT |
| CE | EXPLOSION PROOF |
| FQ | EXPLOSION RESISTANT |
| FD | FIRE RESISTANT |
| FE | FIREPROOF |
| DN | FLAME RESISTANT |
| GF | FLAMEPROOF |
| DP | FUEL RESISTANT |
| DK | FUNGUS PROOF |
| CH | FUNGUS RESISTANT |
| AT | GASTIGHT |
| AP | GENERAL PURPOSE-NEMA TYPE 1 |
| GE | HUMIDITY RESISTANT |
| EC | LEAKTIGHT |
| CP | LIQUID TIGHT |
| DV | MOISTURE PROOF |
| BR | MOISTURE RESISTANT |
| DW | OIL RESISTANT |
| CJ | OILTIGHT |
| CK | RAINPROOF |
| EM | RAINTIGHT |
| GC | SALT SPRAY PROOF |
| FZ | SALT SPRAY RESISTANT |
| DT | SALT WATER RESISTANT |
| BT | SPLASHPROOF |
| CL | SPRAYTIGHT |
| DZ | SUBMERSIBLE |
| EK | VAPOR PROOF |
| ES | VAPORTIGHT |
| FM | VIBRATION PROOF |
| GB | VIBRATION RESISTANT |
| EA | WATER RESISTANT |
| CM | WATERPROOF |
| CN | WATERTIGHT |
| EG | WEATHER RESISTANT |
| DX | WEATHERPROOF |
| GG | WEATHERTIGHT |
HZRD*DHAZARDOUS SUBSTANCES
THE SUBSTANCES AND/OR MATERIALS CONTAINED IN THE ITEM THAT HAVE BEEN IDENTIFIED AS HAZARDOUS OR ENVIRONMENTALLY DAMAGING BY THE ENVIRONMENTAL PROTECTION AGENCY OR OTHER AUTHORIZED GOVERNMENT AGENCY.
Enter the applicable reply code from the table below
(HZRDDHAZ027*;HZRDDHAZ012$$DHAZ012*)
| Table 1 |
| Reply Code (HZ00) | Reply |
| HAZ012 | COPPER |
| HAZ027 | IRIDIUM |
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)