An item used for covering or closing the end of a flanged pipe fitting. The face may be drilled for connecting bolts or studs. Excludes:FLANGE, PIPE.
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED03793*)
AKWEDFACE SEATING SURFACE CONDITION
THE CONDITION OF THE FACE SEATING SURFACE OF AN ITEM WHICH CONTACTS ANOTHER SURFACE.
Enter the applicable reply code from the table below
(AKWEDAS*;AKWEDAF$DAK*)
| Table 1 |
| Reply Code (AA41) | Reply |
| AF | GROUND |
| AS | MACHINED |
| AR | SERRATED |
| AK | UNFINISHED |
MATTDMATERIAL
THE CHEMICAL COMPOUND OR MECHANICAL MIXTURE PROPERTIES OF WHICH THE ITEM IS FABRICATED.
Enter the applicable reply code from the table below
(MATTDALA000*;MATTDZNB000$DST0304*;MATTDZNB000$$DST0304*)
| Table 1 |
| Reply Code (MA01) | Reply |
| ALA000 | ALUMINUM |
| ALB000 | ALUMINUM ALLOY |
| AL2024 | ALUMINUM ALLOY 2024 |
| AL0046 | ALUMINUM ALLOY 356.0 |
| AL0029 | ALUMINUM ALLOY 360.0 |
| AL0031 | ALUMINUM ALLOY 380.0 |
| AL0027 | ALUMINUM ALLOY 413.0 |
| AL0044 | ALUMINUM ALLOY 443.0 |
| AL6061 | ALUMINUM ALLOY 6061 |
| AL7075 | ALUMINUM ALLOY 7075 |
| A | ANY ACCEPTABLE |
| CUA000 | COPPER |
| CUB000 | COPPER ALLOY |
| CU0091 | COPPER ALLOY 360 |
| CU0715 | COPPER ALLOY 715 |
| CU0172 | COPPER ALLOY 836 |
| CU0195 | COPPER ALLOY 903 |
| CU0202 | COPPER ALLOY 922 |
| CU0027 | COPPER ALLOY CA360 |
| CPD000 | ELASTOMER POLYVINYL CHLORIDE |
| GSB000 | GLASS FIBER |
| FEA000 | IRON |
| MGA000 | MAGNESIUM |
| NLB000 | NICKEL ALLOY |
| NL0001 | NICKEL ALLOY A |
| NL0002 | NICKEL ALLOY B |
| NL0014 | NICKEL ALLOY C |
| NL0011 | NICKEL ALLOY D |
| NL0013 | NICKEL ALLOY E |
| NL0022 | NICKEL ALLOY F |
| NL0003 | NICKEL ALLOY H |
| NL0004 | NICKEL ALLOY L |
| NL0024 | NICKEL ALLOY S |
| PCA000 | PLASTIC |
| PCH000 | PLASTIC EPOXY |
| PCAJ00 | PLASTIC POLYVINYL CHLORIDE |
| STA000 | STEEL |
| ST1009 | STEEL COMP 1009 |
| ST1010 | STEEL COMP 1010 |
| ST1020 | STEEL COMP 1020 |
| ST1025 | STEEL COMP 1025 |
| ST1026 | STEEL COMP 1026 |
| ST1035 | STEEL COMP 1035 |
| ST1040 | STEEL COMP 1040 |
| ST1045 | STEEL COMP 1045 |
| ST1050 | STEEL COMP 1050 |
| ST0303 | STEEL COMP 303 |
| ST0304 | STEEL COMP 304 |
| ST0316 | STEEL COMP 316 |
| ST0321 | STEEL COMP 321 |
| ST0410 | STEEL COMP 410 |
| ST8740 | STEEL COMP 8740 |
| ST0037 | STEEL COMP F1 |
| STB000 | STEEL CORROSION RESISTING |
| TTB000 | TITANIUM |
| TTA000 | TITANIUM ALLOY |
| TT0052 | TITANIUM ALLOY UNS R56400 |
| ZNB000 | ZINC |
Reply to this requirement only if the MRC for Material has been answered and there is additional standard specifications that need to be identified on the Material reply.
MDCL*JMATERIAL DOCUMENT AND CLASSIFICATION
THE SPECIFICATION, STANDARD, OR MANUFACTURER'S REFERENCE AND THE CLASSIFICATION DESIGNATION, SUCH AS CLASS, CONDITION, TEMPER, AND THE LIKE, THAT IDENTIFIES THE MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(MDCLJEATEXT1234*;MDCLJEATEXT1234$$JEATEXT1234*;MDCLJEATEXT1234$JEATEXT1234*;MDCL1BJEATEXT1234*;MDCL1BJEATEXT1234$$JEATEXT1234*;MDCL1BJEATEXT1234$JEATEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| Q | AEROSPACE MATERIAL SPEC STD |
| J | AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP18) | Reply |
| M | 10TH MATERIAL RESPONSE |
| N | 11TH MATERIAL RESPONSE |
| P | 12TH MATERIAL RESPONSE |
| Q | 13TH MATERIAL RESPONSE |
| R | 14TH MATERIAL RESPONSE |
| S | 15TH MATERIAL RESPONSE |
| T | 16TH MATERIAL RESPONSE |
| U | 17TH MATERIAL RESPONSE |
| W | 18TH MATERIAL RESPONSE |
| X | 19TH MATERIAL RESPONSE |
| B | 1ST MATERIAL RESPONSE |
| Y | 20TH MATERIAL RESPONSE |
| Z | 21ST MATERIAL RESPONSE |
| V | 22ND MATERIAL RESPONSE |
| C | 2ND MATERIAL RESPONSE |
| D | 3RD MATERIAL RESPONSE |
| E | 4TH MATERIAL RESPONSE |
| F | 5TH MATERIAL RESPONSE |
| H | 6TH MATERIAL RESPONSE |
| J | 7TH MATERIAL RESPONSE |
| K | 8TH MATERIAL RESPONSE |
| L | 9TH MATERIAL RESPONSE |
| G | ALL MATERIAL RESPONSES |
| A | SINGLE MATERIAL RESPONSE |
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AHNX and ABKG and ABKK and AECS)
IF STYLE/REPLY CODE(s) 2 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AJEA and AJDY and AJDZ and ABKK and AJEB and AJEN and AJEP)
IF STYLE/REPLY CODE(s) 3 OR 4 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AJDX and ABKG and AGFF and AHNX and AFQN and AECS)
IF STYLE/REPLY CODE(s) 5 OR 6 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AHNX and ABKG and AFGG and AECS)
IF STYLE/REPLY CODE(s) 7 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AHNX and ABKG and AGFF and AECS)
IF STYLE/REPLY CODE(s) 9 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AHNX and ADVD and ADUZ and ADUY and ADVE and AGFF and AFQN and AECS)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKK)
IF STYLE/REPLY CODE(s) 11 OR 16 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AGFF and AFQN)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AGFF)
IF STYLE/REPLY CODE(s) 17 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (AFQN and AHNX and ADUZ and ADVD and AGFF)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL4)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1326 | 1 | ROUND, ONE BOLT HOLE CIRCLE |
| AAH1334 | 10 | ROUND, NO BOLT HOLES |
| AAH1335 | 11 | OVAL, NO BOLT HOLES |
| AAH1336 | 15 | SQUARE, NO BOLT HOLES |
| AAH1337 | 16 | IRREGULAR HEXAGON, NO BOLT HOLES |
| AAH1338 | 17 | BOLT HOLE CONNECTOR PLATE |
| AAH1327 | 2 | ROUND, TWO BOLT HOLE CIRCLES |
| AAH1328 | 3 | OVAL, ONE BOLT HOLE CIRCLE |
| AAH1329 | 4 | TRIANGULAR, ONE BOLT HOLE CIRCLE |
| AAH1330 | 5 | REGULAR HEXAGON, ONE BOLT HOLE CIRCLE |
| AAH1331 | 6 | OCTAGON, ONE BOLT HOLE CIRCLE |
| AAH1332 | 7 | SQUARE, ONE BOLT HOLE CIRCLE |
| AAH1333 | 9 | RECTANGULAR, WITH BOLT HOLES |
ABKG*JBOLT CIRCLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A BOLT CIRCLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKGJAA2.0*;ABKGJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKK*JFLANGE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A FLANGE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKKJAA2.0*;ABKKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUY*JCENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH
A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE BOLT HOLES ALONG THE WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUYJAA2.0*;ADUYJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADUZ*JCENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH
A MEASUREMENT OF THE CENTER TO CENTER DISTANCE BETWEEN THE BOLT HOLES ALONG THE LENGTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADUZJAA2.0*;ADUZJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVD*JOUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVDJAB2.0*;ADVDJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADVE*JOUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADVEJAC2.0*;ADVEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFGG*JFLANGE WIDTH ACROSS FLATS
THE SHORTEST STRAIGHT LINE BETWEEN FLATS, PERPENDICULIAR TO THE HEIGHT OF THE FLANGE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFGGJAB2.0*;AFGGJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFQN*JFLANGE LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF A FLANGE,IN DISTINCTION FROM WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFQNJAC2.0*;AFQNJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGFF*JFLANGE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A FLANGE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGFFJAB2.0*;AGFFJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AHNX*JBOLT HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE BOLT HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AHNXJAA2.0*;AHNXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJDX*JFLANGE END RADIUS
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJDXJAA2.0*;AJDXJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJDY*JOUTER BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJDYJAB2.0*;AJDYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJDZ*JINNER BOLT CIRCLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJDZJAC2.0*;AJDZJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEA*JOUTER BOLT CIRCLE HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEAJAB2.0*;AJEAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEB*JINNER BOLT CIRCLE HOLE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEBJAC2.0*;AJEBJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AECS*ABOLT HOLE QUANTITY
THE NUMBER OF BOLT HOLES PROVIDED ON THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AECSA10*)
AJEN*AOUTER BOLT CIRCLE HOLE QUANTITY
THE NUMBER OF HOLES PROVIDED ON THE OUTER BOLT CIRCLE OF THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJENA10*)
AJEP*AINNER BOLT CIRCLE HOLE QUANTITY
THE NUMBER OF HOLES PROVIDED ON THE INNER BOLT CIRCLE OF THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AJEPA10*)
IF STYLE/REPLY CODE(s) 1 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEE and AJED and ABNM and AJEG)
IF STYLE/REPLY CODE(s) 2 OR 13 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEE and AJED and ABNM and AJEG)
IF STYLE/REPLY CODE(s) 3 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABMH and ABMD and AJEE and AJED and ABNM and AJEG)
IF STYLE/REPLY CODE(s) 4, 23 OR 44 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and AJEG)
IF STYLE/REPLY CODE(s) 5, 22, 26 OR 28 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM)
IF STYLE/REPLY CODE(s) 6, 12 OR 17 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEG and ABNM)
IF STYLE/REPLY CODE(s) 6A WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEG and ABNM)
IF STYLE/REPLY CODE(s) 7 OR 7A WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABXP and AJEG and ABNM and AJED and AJEE and ABXV)
IF STYLE/REPLY CODE(s) 8 OR 9 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABMH and AJEG and AJED and ABNM and ABMD and AJEE)
IF STYLE/REPLY CODE(s) 10 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABMH and AJEG and ABNM and AJED and ABMD and AJEE)
IF STYLE/REPLY CODE(s) 11 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and AJED and AJEE)
IF STYLE/REPLY CODE(s) 14 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABXP and AJEG and ABNM and ABXN)
IF STYLE/REPLY CODE(s) 15 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ADCL and AJEG and ABNM)
IF STYLE/REPLY CODE(s) 16 OR 16A WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABXP and ABXV and AJEG and ABNM)
IF STYLE/REPLY CODE(s) 18 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABXP and AJEG and ABNM and AJED and AJEE and ABXN)
IF STYLE/REPLY CODE(s) 19 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABMH and ABNM and ABMD)
IF STYLE/REPLY CODE(s) 20 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABMD and ABNM and ABXN)
IF STYLE/REPLY CODE(s) 21 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABXP and AJEG and ABXN and ABNM and AJED and ABXV and AJEE)
IF STYLE/REPLY CODE(s) 24, 25 OR 29 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and AJED)
IF STYLE/REPLY CODE(s) 27 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and AJED and ABMD and AJEE)
IF STYLE/REPLY CODE(s) 30 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ADCL and AJEG and ABNM)
IF STYLE/REPLY CODE(s) 35 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (CQXL and AJEF and ABNM)
IF STYLE/REPLY CODE(s) 36 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (CQXL and AJEF and ABNM and AJEG)
IF STYLE/REPLY CODE(s) 38 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEG and ABNM and ABMD and ABMH)
IF STYLE/REPLY CODE(s) 39 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (CSRC and AJEF and ADCL and ABNM and AJEG)
IF STYLE/REPLY CODE(s) 41 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEG and ABNM)
IF STYLE/REPLY CODE(s) 42 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (CSRC and AJEF and AJEG and ABNM)
IF STYLE/REPLY CODE(s) 45 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and ABMH and ABMD)
IF STYLE/REPLY CODE(s) 46 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (CSRC and ABNM and AJEG and ADCL)
IF STYLE/REPLY CODE(s) 47 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEE and ABMD and ABMH and AJED and ABNM and AJEG and CSRC and ADCL)
IF STYLE/REPLY CODE(s) 48 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (CSRC and AGMH and ABNM and AJEG and ADCL)
IF STYLE/REPLY CODE(s) 49 OR 50 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and AJEG and CWWT)
IF STYLE/REPLY CODE(s) 51 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (ABNM and AJEG and ADCL)
IF STYLE/REPLY CODE(s) 52 WERE ENTERED FOR MRC AJEM, YOU MUST ANSWER MRC (AJEG and ABNM)
AJEMLFLANGE SECTION STYLE
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE FLANGE SECTION.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(AJEML39)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AAH1339 | 1 | RAISED FACE, RAISED NECK |
| AAH1348 | 10 | FEMALE FACE, RAISED NECK |
| AAH1349 | 11 | RAISED FACE, WELDING NECK |
| AAH1350 | 12 | PLAIN FACE, WELDING NECK |
| AAH1351 | 13 | RAISED FACE, WELDING NECK |
| AAH1352 | 14 | PLAIN FACE, SOCKET NECK |
| AAH1353 | 15 | PLAIN FACE, LONG NECK |
| AAH1354 | 16 | PLAIN FACE, SOCKET BRAZING NECK |
| AAH1386 | 16A | PLAIN FACE, SOCKET BRAZING NECK W/O BRAZING RING |
| AAH1355 | 17 | PLAIN FACE, WELDING NECK |
| AAH1356 | 18 | RAISED FACE, SOCKET NECK |
| AAH1357 | 19 | PLAIN RECESSED FACE |
| AAH1340 | 2 | RAISED FACE, WELDING NECK |
| AAH1358 | 20 | PLAIN FACE, SOCKET NECK |
| AAH1359 | 21 | RAISED FACE SOCKET NECK (BULK HEAD) |
| AAH1360 | 22 | PLAIN FACE (BLIND) |
| AAH1361 | 23 | PLAIN FACE, RAISED FACE (BLIND) |
| AAH1362 | 24 | RAISED FACE (BLIND) |
| AAH1363 | 25 | RAISED FACE DISHED (BLIND) |
| AAH1364 | 26 | RECESSED FACE (BLIND) |
| AAH1365 | 27 | TONGUED FACE (BLIND) |
| AAH1366 | 28 | PLAIN FACE, DISHED (BLIND) |
| AAH1367 | 29 | RAISED FACE WELDING (BLIND) |
| AAH1341 | 3 | RAISED AND RECESSED FACE, RAISED NECK |
| AAH1368 | 30 | PLAIN FACE, WELDING NECK |
| AAH1369 | 35 | BEVELED FACE |
| AAH1370 | 36 | BEVELED FACE, RAISED NECK |
| AAH1371 | 38 | RECESSED FACE, RAISED NECK |
| AAH1372 | 39 | PLAIN FACE, BEVELED RAISED NECK |
| AAH1342 | 4 | PLAIN FACE, RAISED NECK |
| AAH1373 | 41 | PLAIN FACE, WRENCHING NECK |
| AAH1374 | 42 | PLAIN FACE, RAISED NECK |
| AAH1375 | 44 | PLAIN FACE, LAPPED JOINT WELDING NECK |
| AAH1376 | 45 | RAISED FACED, DISHED |
| AAH1377 | 46 | RAISED FACE, THREADED NECK |
| AAH1378 | 47 | EXTERNAL FACE, THREADED NECK |
| AAH1379 | 48 | INTERNAL GROOVE, THREADED NECK |
| AAH1380 | 49 | RAISED FACE, THREADED CONICAL EXTERNAL |
| AAH1343 | 5 | PLAIN FACE |
| AAH1381 | 50 | RAISED FACE, THREADED CONICAL INTERNAL |
| AAH1382 | 51 | RAISED FACE, THREADED NECK |
| AAH1383 | 52 | PLAIN FACE WITH "O" RING |
| AAH1344 | 6 | PLAIN FACE, BRAZING NECK |
| AAH1384 | 6A | PLAIN FACE, BRAZING NECK W/O BRAZING RING |
| AAH1345 | 7 | RAISED FACE, BRAZING NECK |
| AAH1385 | 7A | RAISED FACE, BRAZING NECK (BULKHEAD) W/O BRAZING RING |
| AAH1346 | 8 | FEMALE FACE, WELDING NECK |
| AAH1347 | 9 | FEMALE FACE, WELDING NECK |
ABMD*JRECESS DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF THE RECESS,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMDJAA2.0*;ABMDJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMH*JRECESS DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE RECESS,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMHJAA2.0*;ABMHJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNM*JTHICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF AN ITEM,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNMJAC2.0*;ABNMJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXN*JSOCKET DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS ON THE SOCKET,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXNJAA2.0*;ABXNJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXP*JSOCKET DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SOCKET,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXPJAA2.0*;ABXPJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXV*JBORE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A CIRCULAR BORE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXVJAC2.0*;ABXVJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADCL*JNECK DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A NECK,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADCLJAA2.0*;ADCLJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AGMH*JGROOVE OUTSIDE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AGMHJAC2.0*;AGMHJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJED*JRAISED FACE HEIGHT
A MEASUREMENT FROM THE BOTTOM TO THE TOP SURFACE OF A RAISED FACE,IN DISTINCTION FROM DEPTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEDJAC2.0*;AJEDJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEE*JRAISED FACE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A RAISED FACE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEEJAC2.0*;AJEEJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEF*JBEVEL DEPTH
AN INSIDE MEASUREMENT BETWEEN SPECIFIED POINTS ON THE BEVEL,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEFJAC2.0*;AJEFJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEG*JNECK HEIGHT
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEGJAC2.0*;AJEGJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CWWT*JGAGE DIAMETER
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CWWTJAB2.0*;CWWTJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CQXL*JFACE BEVEL ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQXLJDC2.0*;CQXLJDC2.0$$JDC2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CSRC*JBOSS BEVEL ANGLE
NONE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSRCJDA2.0*;CSRCJDA2.0$$JDA2.1*)
| Table 1 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
SFTT*DSURFACE TREATMENT
THE METALLIC,NONMETALLIC,AND/OR CHEMICAL PROPERTIES WITH WHICH THE ITEM IS PLATED,DIPPED,AND/OR COATED.THE TREATMENT IS DESIGNED TO PROTECT THE SURFACE(S) AND CANNOT BE WIPED OFF.
Enter the applicable reply code from the table below
(SFTTDLQA000*;SFTTDENA000$DXXB000*;SFTTDENA000$$DXXB000*)
| Table 1 |
| Reply Code (SF01) | Reply |
| ANA000 | ANODIZE |
| A | ANY ACCEPTABLE |
| CDA000 | CADMIUM |
| CMA000 | CHROMATE |
| CMC000 | CHROMATE MAGNESIUM |
| CMB000 | CHROMATE ZINC |
| CRA000 | CHROMIUM |
| DCA000 | DICHROMATE |
| ENA000 | ENAMEL |
| ENB000 | ENAMEL LUSTERLESS |
| ENC000 | ENAMEL SYNTHETIC LUSTERLESS |
| LQA000 | LACQUER |
| NLA000 | NICKEL |
| XXB000 | OXIDE |
| XXA000 | OXIDE FILM |
| PNA000 | PAINT |
| PNB000 | PAINT HEAT RESISTANT |
| PSA000 | PASSIVATE |
| PHA000 | PHOSPHATE |
| PRA000 | PRIMER |
| ZNA000 | ZINC |
STDC*JSURFACE TREATMENT DOCUMENT AND CLASSIFICATION
THE SPECIFICATION,STANDARD,OR MANUFACTURERS REFERENCE,AND THE CLASSIFICATION DESIGNATION,SUCH AS TYPE,CLASS,GRADE,AND THE LIKE,THAT IDENTIFIES THE SURFACE TREATMENT MATERIAL.
Enter the applicable Reply Code from Tables 1 & 2 below followed by an alpha-numeric reply with a minimum of one character as in the first, second, and third examples. If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Tables 2 & 3 below followed by an alpha-numeric reply with a minimum of one character as in the fourth, fifth, and sixth examples.
(STDCJEGTEXT1234*;STDCJEGTEXT1234$$JEGTEXT1234*;STDCJEGTEXT1234$JEGTEXT1234*; STDC1BJEGTEXT1234*;STDC1BJEGTEXT1234$$JEGTEXT1234*;STDC1BJEGTEXT1234$JEGTEXT1234*)
| Table 1 |
| Reply Code (AP33) | Reply |
| G | ASSN STD |
| A | COMMERCIAL ITEM DESCRIPTION |
| K | DEF STAN/SPEC |
| B | FED SPEC |
| C | FED STD |
| L | GOVERNMENT STD/SPEC |
| N | INTERNATIONAL STD/SPEC |
| F | MFR REF |
| D | MIL SPEC |
| E | MIL STD |
| H | NATIONAL SPEC |
| P | NATIONAL STD |
| M | NATIONAL STD/SPEC |
| Table 2 |
| Reply Code (AP39) | Reply |
| M | 10TH TREATMENT RESPONSE |
| N | 11TH TREATMENT RESPONSE |
| P | 12TH TREATMENT RESPONSE |
| Q | 13TH TREATMENT RESPONSE |
| R | 14TH TREATMENT RESPONSE |
| S | 15TH TREATMENT RESPONSE |
| B | 1ST TREATMENT RESPONSE |
| C | 2ND TREATMENT RESPONSE |
| D | 3RD TREATMENT RESPONSE |
| E | 4TH TREATMENT RESPONSE |
| F | 5TH TREATMENT RESPONSE |
| H | 6TH TREATMENT RESPONSE |
| J | 7TH TREATMENT RESPONSE |
| K | 8TH TREATMENT RESPONSE |
| L | 9TH TREATMENT RESPONSE |
| G | ALL TREATMENT RESPONSES |
| A | SINGLE TREATMENT RESPONSE |
ACSU*JNOMINAL PIPE SIZE FOR WHICH DESIGNED
THE INDUSTRIAL DESIGNATION OR TERM USED TO DEFINE THE NOMINAL DIAMETER OF PIPE FOR WHICH THE ITEM IS DESIGNED.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ACSUJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
IF STYLE/REPLY CODE(s) AN, BR, BS, BW, NP, NT, PM, SC, SL, SM, SP OR SS WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (CQJX)
IF STYLE/REPLY CODE(s) NH WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX and TPMM)
IF STYLE/REPLY CODE(s) UN WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and TPMM and AAJD)
IF STYLE/REPLY CODE(s) NF WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (CQJX and AAJD)
IF STYLE/REPLY CODE(s) NJ WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and TPMM and AAJD)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC AJYP, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and CMLP and AAJE) or (CQJX and TPMM and AAJD) or (CQJX and TPMM and AAJE)
AJYP*DSCREW THREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF SCREW THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable reply code from the table below
(AJYPDSS)
| Table 1 |
| Reply Code (AH06) | Reply |
| AN | ANPT |
| BS | BSP.TR EXT |
| BR | BSP.TR INT |
| BW | BSW |
| SM | ISO M |
| SS | ISO S |
| NH | NH |
| SP | NPS |
| SC | NPSC |
| SL | NPSL |
| PM | NPSM |
| NP | NPT |
| NT | NPTF |
| UN | UN |
| NF | UNF |
| NJ | UNJ |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJXJA2.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the alpha-numeric reply with a minimum of one character.
(CMLPAH6)
TPMM*JTHREAD PITCH IN MILLIMETERS
THE DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(TPMMJB2.0*;TPMMJB2.0$$JB2.1*)
| Table 1 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the alpha-numeric reply with a minimum of one character.
(AAJDAP4)
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJEJAM32.0/P50.0*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQCJ*JMAXIMUM OPERATING PRESSURE AND MEDIA FOR WHICH DESIGNED
THE MAXIMUM PRESSURE AT WHICH AN ITEM IS RATED TO OPERATE FOR EACH TYPE OF SERVICE WITH WHICH AN ITEM MAY BE USED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQCJJPAAQ2.0*;CQCJJPAAQ2.0$$JPAAQ2.1*)
| Table 1 |
| Reply Code (AN71) | Reply |
| B | BAR |
| K | KILOGRAMS PER SQUARE CENTIMETER |
| N | NEWTONS PER SQUARE CENTIMETER |
| P | POUNDS PER SQUARE INCH |
| Table 2 |
| Reply Code (AN91) | Reply |
| AAE | AIR |
| AAA | ANY ACCEPTABLE |
| AAY | FUEL/OIL, HYDROCARBON |
| AAQ | GAS |
| ACJ | OIL |
| ABC | OIL, LUBRICATING, DIESTER BASE |
| ABK | OXYGEN, LIQUID |
| ABP | STEAM |
| ABR | WATER |
| ABT | WATER, SALT |
CRWH*JMAXIMUM OPERATING TEMP AND MEDIA FOR WHICH DESIGNED
A RATING WHICH EXPRESSES THE DEGREE OF HEAT OR COLD AS APPLIED TO THE OPERATION,OR LIMITATION OF OPERATION,FOR EACH TYPE OF SERVICE WITH WHICH AN ITEM MAY BE USED.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRWHJCAAQ2.0*;CRWHJCAAQ2.0$$JCAAQ2.1*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
| Table 2 |
| Reply Code (AN91) | Reply |
| AAE | AIR |
| AAA | ANY ACCEPTABLE |
| AAY | FUEL/OIL, HYDROCARBON |
| AAQ | GAS |
| ACJ | OIL |
| ABC | OIL, LUBRICATING, DIESTER BASE |
| ABK | OXYGEN, LIQUID |
| ABP | STEAM |
| ABR | WATER |
| ABT | WATER, SALT |
ABFF*DFURNISHED ITEMS
ITEMS FURNISHED AS ACCESSORIES WHICH ARE NOT SPECIFIED ELSEWHERE.
Enter the applicable reply code from the table below
(ABFFDAMX*;ABFFDABW$$DAFN*)
| Table 1 |
| Reply Code (AB28) | Reply |
| ABR | BOLT |
| ACN | GASKET |
| ABW | NUT |
| AQQ | PIPE PLUG |
| AMX | SCREW |
| AFJ | SETSCREW |
| AFN | STUD |
ABGA*JGROOVE DEPTH
A MEASUREMENT BETWEEN SPECIFIED POINTS OF A GROOVE,IN DISTINCTION FROM HEIGHT.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGAJAB2.0*;ABGAJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABGF*JGROOVE WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF A GROOVE,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABGFJAA2.0*;ABGFJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AJEY*JGROOVE PITCH DIAMETER
THE PITCH DIAMETER OF THE GROOVE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AJEYJAB2.0*;AJEYJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDBBA*;CBBLDBBE$$DBBD*)
| Table 1 |
| Reply Code (AN47) | Reply |
| BBA | COUNTERBORED BOLT HOLES |
| BBC | LIFTING RING |
| BBE | LIQUID OXYGEN PREPARED |
| BBD | PINHOLE GUIDE |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCF2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CF | CUBIC FEET |
| CM | CUBIC METERS |
BGTB*HSTORAGE FACILITY
THE STORAGE FACILITY STANDARDS ESTABLISHED TO ASSURE THE SERVICEABILITY OF SUPPLIES IN STORAGE.
Enter the applicable Reply Code from Tables 1 & 2 & 3 below.
(BGTBHCABAE2.0*;BGTBHCABAE2.0$HCABAE2.0*;BGTBHCABAE2.0$$HCABAE2.1*)
| Table 1 |
| Reply Code (AN11) | Reply |
| D | ALTERNATE |
| B | MANDATORY |
| C | PREFERRED |
| Table 2 |
| Reply Code (AM81) | Reply |
| AB | ABOVE GROUND MAGAZINE |
| AT | DOCK LEVEL HEATED WAREHOUSE |
| AX | DOCK LEVEL UNHEATED WAREHOUSE |
| AS | GROUND LEVEL HEATED WAREHOUSE |
| AW | GROUND LEVEL UNHEATED WAREHOUSE |
| AF | IGLOO MAGAZINE |
| AG | IMPROVED OPEN |
| AR | SHED |
| AK | UNIMPROVED OPEN |
| Table 3 |
| Reply Code (AN12) | Reply |
| AF | CHILL |
| AC | CONTROLLED HUMIDITY |
| AD | FLAMMABLE |
| AG | FREEZE |
| AB | GENERAL PURPOSE |
| AH | HEAVY DUTY |
| AE | SECURITY |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAUA000*;PRMTDAGA000$DPTA000*;PRMTDAGA000$$DPTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJIRA000E2.0*;PMWTJIRA000E2.0$$JIRA000E2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPTA0002.0*;PMLCJPTA0002.0$JPTA0002.0*;PMLCJPTA0002.0$$JPTA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(ZZZPJ81A37-30624A*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)
FSC Information