A switch actuated by a definite angular rotation of the switch shaft about its axis. It consists of a BODY,SWITCH and a CONTROL,ROTARY SWITCH. For items having rated actuation travel and pressure characteristics, see SWITCH,SENSITIVE. Excludes RELAY,ROTARY; SWITCH,STEPPING; and SWITCH,TELEPHONE (as modified).
NAMEDITEM NAME
NOUN, WITH OR WITHOUT MODIFIERS, BY WHICH AN ITEM OF SUPPLY IS KNOWN.
Enter the item name code.
(NAMED02134*)
CQMKBCONTACT VOLTAGE RATING IN VOLTS
THE VOLTAGE FOR WHICH THE CONTACTS ARE RATED,EXPRESSED IN VOLTS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(CQMK3ARSB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ARP | AC AT SEA LEVEL |
| 3ARQ | AC AT ALTITUDE |
| 3ARR | DC AT SEA LEVEL |
| 3ARS | DC AT ALTITUDE |
| 3ART | HIGHEST AC VOLTAGE RATING AT SEA LEVEL |
| 3ARU | HIGHEST AC VOLTAGE RATING AT ALTITUDE |
| 3ARV | LOWEST AC VOLTAGE RATING AT SEA LEVEL |
| 3ARW | LOWEST AC VOLTAGE RATING AT ALTITUDE |
| 3ARX | HIGHEST DC VOLTAGE RATING AT SEA LEVEL |
| 3ARY | HIGHEST DC VOLTAGE RATING AT ALTITUDE |
| 3ARZ | LOWEST DC VOLTAGE RATING AT SEA LEVEL |
| 3ASA | LOWEST DC VOLTAGE RATING AT ALTITUDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CTHFJCONTACT LOAD CURRENT RATING
THE AMOUNT OF CURRENT THAT THE CONTACTS ARE RATED TO MAKE OR BREAK WITH A SPECIFIED LOAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CTHF3ARSJLAE2.0*;CTHF3ARSJLAE2.0$JLAE2.0*;CTHF3ARSJLAE2.0$$JLAE2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ARP | AC AT SEA LEVEL |
| 3ARQ | AC AT ALTITUDE |
| 3ARR | DC AT SEA LEVEL |
| 3ARS | DC AT ALTITUDE |
| 3ART | HIGHEST AC VOLTAGE RATING AT SEA LEVEL |
| 3ARU | HIGHEST AC VOLTAGE RATING AT ALTITUDE |
| 3ARV | LOWEST AC VOLTAGE RATING AT SEA LEVEL |
| 3ARW | LOWEST AC VOLTAGE RATING AT ALTITUDE |
| 3ARX | HIGHEST DC VOLTAGE RATING AT SEA LEVEL |
| 3ARY | HIGHEST DC VOLTAGE RATING AT ALTITUDE |
| 3ARZ | LOWEST DC VOLTAGE RATING AT SEA LEVEL |
| 3ASA | LOWEST DC VOLTAGE RATING AT ALTITUDE |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN86) | Reply |
| AM | AMPERES |
| UA | MICROAMPERES |
| LA | MILLIAMPERES |
| Table 3 |
| Reply Code (AD92) | Reply |
| C | INDUCTIVE LOAD |
| D | LAMP LOAD |
| E | MOTOR LOAD |
| B | RESISTIVE LOAD |
CSCFDTERMINAL TYPE
INDICATES THE TYPE OF TERMINAL FOR PROVIDING ELECTRICAL CONNECTION TO THE ITEM.
Enter the applicable reply code from the table below
(CSCFDAAF*;CSCFDACB$$DADA*)
| Table 1 |
| Reply Code (AN89) | Reply |
| ADB | CLIP |
| ACT | COMPONENT SOCKET |
| ACN | CONNECTOR, PLUG |
| AAF | CONNECTOR, RECEPTACLE |
| AJT | ELECTRON TUBE BASE |
| AAM | PIN |
| ACR | PRINTED CIRCUIT |
| ADA | QUICK DISCONNECT, FEMALE |
| ACZ | QUICK DISCONNECT, MALE |
| ABQ | SCREW |
| AAS | SOLDER STUD |
| ABX | TAB W/SCREW |
| ABB | TAB, SOLDER LUG |
| ABD | THREADED STUD |
| ACB | TURRET |
| ACM | WIRE HOOK |
| ACC | WIRE LEAD |
| ACD | WIRE LOOP |
Reference NotesRefer to Reference Drawings for assitance in answering this MRC.
CRJHASWITCH ACTUATOR INDEXING POSITION QUANTITY
THE NUMBER OF POSITIONS TO WHICH THE SWITCH ACTUATOR MAY BE INDEXED.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(CRJH3AMJA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMA | FOURTH ACTUATOR |
| 3AMB | FIFTH ACTUATOR |
| 3AMC | SIXTH ACTUATOR |
| 3AMD | SEVENTH ACTUATOR |
| 3AME | EIGHTH ACTUATOR |
| 3AMG | TENTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
IF STYLE/REPLY CODE(s) 1, 2, 3, 6, 7, 11, 13, 14, 15, 17, 21, 26, 27, 28, 29 OR 30 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABMK and ABKW and ABHP)
IF STYLE/REPLY CODE(s) 4, 5 OR 10 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABMK and ABKW and ABHP)
IF STYLE/REPLY CODE(s) 4A, 5A OR 10A WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABHP and ADAV)
IF STYLE/REPLY CODE(s) 8, 12, 16, 18, 19 OR 20 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and ABHP)
IF STYLE/REPLY CODE(s) 22 OR 25 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ABKW and ABMK and ADPR)
IF STYLE/REPLY CODE(s) 23 WERE ENTERED FOR MRC STYL, YOU MUST ANSWER MRC (ADAV and ADPR)
STYLLSTYLE DESIGNATOR
THE STYLE DESIGNATION INDICATING THE CONFIGURATION THAT MOST NEARLY CORRESPONDS TO THE APPEARANCE OF THE ITEM.
Review the representative drawings below, find the drawing which best represents your item.Use the Physical Drawing ID (eg: AAT1001) to identify the row(s) in the table which are applicable to your drawing.Enter the applicable reply code from the table below.
(STYLL11)
| Table 1 |
| Physical Drawing ID | Reply Code (STYL) | Reply |
| AJ10001 | 1 | TAP, CIRCUIT SELECTOR |
| DR03125 | 10 | TAP, CIRCULAR FRAME |
| DR03126 | 10A | TAP, CIRCULAR FRAME |
| AJ10011 | 11 | TAP, SQUARE FRAME |
| AJ10012 | 12 | SNAP OR LINE |
| AJ10013 | 13 | IN-LINE, PILE-UP, PANEL MOUNT |
| AJ10014 | 14 | IN-LINE, PILE-UP, BUSHING MOUNT |
| AJ10015 | 15 | IN-LINE, PILE-UP, BUSHING MOUNT |
| AJ10016 | 16 | CIRCULAR, CAM ACTUATED |
| AJ10017 | 17 | IN-LINE, CAM ACTUATED |
| AJ10018 | 18 | MINIATURE, BUSHING MOUNT |
| AJ10019 | 19 | MINIATURE, PIN MOUNT |
| AJ10002 | 2 | PARTIAL WAFER, BUSHING MOUNT |
| AJ10020 | 20 | MINIATURE, PIN MOUNT, INTEGRAL KNOB |
| AJ10021 | 21 | SQUARE WAFER, PANEL MOUNT |
| AJ10022 | 22 | SWITCH SECTION, ROTARY |
| AJ10023 | 23 | SWITCH SECTION, ROTARY |
| AJ10024 | 25 | SWITCH SECTION, ROTARY |
| AJ10025 | 26 | MINIATURE BUSHING MOUNT INTEGRAL KNOB |
| AJ10026 | 27 | RECTANGULAR PANEL MOUNT |
| AJ10027 | 28 | MINIATURE PANEL MOUNT |
| AJ10028 | 29 | RECTANGULAR INDICATING |
| AJ10003 | 3 | SEMI-CIRCULAR WAFER, BUSHING MOUNT |
| AJ10029 | 30 | RECTANGULAR INLINE INDICATING |
| DR03121 | 4 | CIRCULAR WAFER, BUSHING MOUNT |
| DR03122 | 4A | CIRCULAR WAFER, BUSHING MOUNT |
| DR03123 | 5 | CIRCULAR WAFER, PANEL MOUNT |
| DR03124 | 5A | CIRCULAR WAFER, PANEL MOUNT |
| AJ10006 | 6 | WAFER, PRINTED BOARD, BUSHING MOUNT |
| AJ10007 | 7 | STRAIGHT WAFER |
| AJ10008 | 8 | TAP, CIRCULAR, BUSHING MOUNT |
| AJ10009 | 9 | TAP, CIRCULAR, BUSHING MOUNT |
ABHP*JOVERALL LENGTH
THE DIMENSION MEASURED ALONG THE LONGITUDINAL AXIS WITH TERMINATED POINTS AT THE EXTREME ENDS OF THE ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABHPJAC2.0*;ABHPJAC2.0$$JAC2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABKW*JOVERALL HEIGHT
THE DISTANCE MEASURED IN A STRAIGHT LINE FROM THE BOTTOM TO THE TOP OF AN ITEM.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABKWJAB2.0*;ABKWJAB2.0$$JAB2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABMK*JOVERALL WIDTH
AN OVERALL MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF AN ITEM,IN DISTINCTION FROM THICKNESS.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABMKJAA2.0*;ABMKJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADAV*JOVERALL DIAMETER
A MEASUREMENT OF THE LONGEST STRAIGHT LINE ACROSS A CIRCULAR CROSS-SECTIONAL PLANE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADAVJAA2.0*;ADAVJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ADPR*JBODY THICKNESS
A MEASUREMENT OF THE SMALLEST DIMENSION OF A BODY,IN DISTINCTION FROM LENGTH OR WIDTH.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ADPRJAA2.0*;ADPRJAA2.0$$JAA2.1*)
| Table 1 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 2 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFBH*AINDIVIDUAL SECTION QUANTITY
THE NUMBER OF INDIVIDUAL SECTIONS INCLUDED IN THE ITEM.
Enter the numeric reply with a minimum of one digit.
(AFBHA10*)
IF STYLE/REPLY CODE(s) E WERE ENTERED FOR MRC AJZE, YOU MUST ANSWER MRC (CTZT)
AJZE*DSWITCH CONTACT BASIC DESIGN
THE GENERAL CONFIGURATION OF THE CONTACTS OF A SWITCH THAT DESCRIBES ITS BASIC SWITCHING STRUCTURE.
Enter the applicable reply code from the table below
(AJZEDD*;AJZEDB$$DE*)
| Table 1 |
| Reply Code (AD79) | Reply |
| E | CODED |
| D | NONPILE-UP NONSYMMETRICAL |
| C | NONPILE-UP SYMMETRICAL |
| B | PILE-UP |
IF STYLE/REPLY CODE(s) ADR WERE ENTERED FOR MRC CTZT, YOU MUST ANSWER MRC (STTB)
CTZT*DCONTACT ARRANGEMENT TRUTH TABLE
AN INDICATION OF THE CONFIGURATION OF THE CODED CONTACT SWITCHING STRUCTURE.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CTZT3AGKDADL*;CTZT3AGKDADL$DAEA*;CTZT3AGKDADL$$DAEA*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABU | SINGLE SECTION |
| 3ACU | FLANGE |
| 3AEE | OVERALL |
| 3AFU | NINTH SECTION |
| 3AGK | EACH SECTION |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP70) | Reply |
| ADY | 0-1-3-3' CODE, 10 POSITIONS |
| ADZ | 1 PAIR 5 POSITIONS REPEATING NO OUTPUT ON 0 OR 5, 10 POSITIONS |
| AEM | 1, 2, 4, 5, 6, 7, 8, 9 CODE, 10 POSITIONS |
| AFE | 10'S COMPLEMENT BCD WITH COMPLEMENT, 1 POLE - 10 POSITIONS |
| AFF | 10'S COMPLEMENT BCD WITH COMPLEMENT, 2 POLE - 10 POSITIONS |
| AFG | 10'S COMPLEMENT BCD, 1 POLE - 10 POSITIONS |
| AEC | 1-1'-2-5 CODE MODIFIED, 1 POLE - 10 POSITIONS |
| AEB | 1-1-2-5 CODE PLUS COMPLEMENT WITH SEPARATE COMMON TO NOT-TRUE BITS, 10 POSITIONS |
| AEA | 11'25 CODE, 1 POLE - 10 POSITIONS |
| AEF | 1-2-2'-4 BERKELEY CODE, 1 POLE - 10 POSITIONS |
| AEE | 1-2-2-4 CODE WITH SEPARATE TO NOT-TRUE BITS, 10 POSITIONS |
| AEG | 1234 CODE, 1 POLE - 10 POSITIONS |
| AEH | 1242' CODE, 1 POLE - 10 POSITIONS |
| AEJ | 1242' WITH COMPLEMENT, 1 POLE - 10 POSITIONS |
| AFL | 1-2-4-4' BINARY CODED DECIMAL, 12 POSITIONS |
| AEK | 1-2-4-4 CODE WITH COMPLEMENT, 11 POSITIONS |
| AEL | 1-2-4-5 CODE, 10 POSITIONS |
| AEN | 1-2-4-7 CODE WITH EVEN BIT PARITY, 10 POSITIONS |
| AEP | 1-2-4-7 CODE, 11 AT 0, WITH EVEN BIT PARITY, 10 POSITIONS |
| AEQ | 2 OF 6 CODES, 11 POSITIONS |
| AER | 2 OUT OF 5 LINE CODE, 2 POLE - 10 POSITIONS |
| AEU | 2 POLE - 2 THROW, 2 COMMONS, 10 POSITIONS |
| AEV | 2 POLE - 5 POSITIONS REPEATING |
| AES | 2 POLE CHANGEOVER SWITCH, 10 POSITIONS |
| AFM | 2 POLE, 1-1'-2-5 WITH COMPLEMENT |
| AET | 2 POLE, DOUBLE THROW REPEATING, 10 POSITIONS |
| AEW | 3 POLE SINGLE POLE DECIMAL, 10 POSITIONS |
| AEX | 5 LINE TELETYPE WITH EVEN BIT PARITY, 1 POLE - 1O POSITIONS |
| AEY | 5 LINE TELETYPE, 1 POLE - 10 POSITIONS |
| AEZ | 7 BAR DISPLAY, SINGLE POLE, 10 POSITIONS |
| AFA | 7 SEGMENT CODE, 10 POSITIONS |
| AFB | 9'S COMPLEMENT BCD WITH COMPLEMENT, 1 POLE - 10 POSITIONS |
| AFC | 9'S COMPLEMENT BCD WITH COMPLEMENT, 2 POLE - 10 POSITIONS |
| AFD | 9'S COMPLEMENT BCD, 1 POLE - 10 POSITIONS |
| AAB | AIKEN POSITIVE PLUS COMPLEMENT, 10 POSITIONS |
| AAC | AIKEN POSITIVE, 10 POSITIONS |
| AAD | BALANCE CODE, 10 POSITIONS |
| ABT | BCD 10 AT 0, WITH ODD BIT PARITY, 1 POLE - 10 POSITIONS |
| ABS | BCD 10 AT 0, WITH ODD BIT PARITY, MOD. 1 POLE - 10 POSITIONS |
| ABR | BCD 9'S COMPLEMENT, 2 POLE - 10 POSITIONS |
| AAE | BCD AND DECIMAL, 2 POLE - 10 POSITIONS |
| AAF | BCD BINARY 10 TO 0, 1 POLE - 10 POSITIONS |
| AAG | BCD COMPLEMENT ONLY AND DECIMAL, 1 POLE - 10 POSITIONS |
| AAJ | BCD COMPLEMENT ONLY, 1 POLE - 10 POSITIONS |
| AAH | BCD COMPLEMENT ONLY, 1 POLE - 8 POSITIONS |
| AAK | BCD COMPLEMENT WITH EVEN BIT PARITY, 1 POLE - 10 POSITIONS |
| AAL | BCD COMPLEMENT WITH ODD BIT PARITY, 1 POLE - 10 POSITIONS |
| AAM | BCD DUAL, 2 POLE - 10 POSITIONS |
| AAN | BCD EXCESS 3 WITH COMPLEMENT, 1 POLE - 10 POSITIONS |
| AAP | BCD EXCESS 3 WITH COMPLEMENT, 2 POLE - 10 POSITIONS |
| AAQ | BCD EXCESS 3, 1 POLE - 10 POSITIONS |
| AAR | BCD EXCESS 6 AND COMPLEMENT, 10 POSITIONS |
| ABL | BCD WITH 0 BIT, 10 POSITIONS |
| ABM | BCD WITH 0 BIT, 12 POSITIONS |
| ABK | BCD WITH 0 BIT, 7 POSITIONS |
| AAV | BCD WITH COMPLEMENT AND DECIMAL, 1 POLE - 10 POSITIONS |
| AAW | BCD WITH COMPLEMENT BINARY 10 TO 1, 1 POLE - 10 POSITIONS |
| AAY | BCD WITH COMPLEMENT, 1 POLE - 10 POSITIONS |
| AAZ | BCD WITH COMPLEMENT, 1 POLE - 16 POSITIONS |
| AAX | BCD WITH COMPLEMENT, 1 POLE - 8 POSITIONS |
| ABD | BCD WITH COMPLEMENT, 11 POSITIONS |
| ABB | BCD WITH COMPLEMENT, 2 POLE - 10 POSITIONS |
| ABA | BCD WITH COMPLEMENT, 2 POLE - 8 POSITIONS |
| ABC | BCD WITH COMPLEMENT, 3 POLE - 8 POSITIONS |
| ABE | BCD WITH EVEN BIT PARITY, 1 POLE - 10 POSITIONS |
| ABF | BCD WITH ODD BIT PARITY, 1 POLE - 10 POSITIONS |
| ABG | BCD WITH ODD BIT PARITY, 8 POSITIONS |
| ABH | BCD WITH SEPARATE COMMON TO NOT-TRUE BITS, 2 POLE - 12 POSITIONS |
| ABJ | BCD WITH SPECIAL R POSITION, 10 POSITIONS |
| ABP | BCD, 1 POLE - 10 POSITIONS |
| ABQ | BCD, 1 POLE - 16 POSITIONS |
| ABN | BCD, 1 POLE - 8 POSITIONS |
| AAU | BCD, SEPARATE COMMON TO NOT-TRUE BITS, 2 POLE - 10 POSITIONS |
| AAT | BCD, SEPARATE COMMON TO NOT-TRUE BITS, 2 POLE - 8 POSITIONS |
| ABU | BERKELEY CODE 1-2-2'4 PLUS COMPLEMENT, 1 COMMON - 10 POSITIONS |
| ABW | BINARY CODE WITH COMPLEMENT, 1 POLE - 12 POSITIONS |
| ABX | BINARY CODE WITH COMPLEMENT, 2 POLE - 12 POSITIONS |
| ABY | BINARY CODE WITH COMPLEMENT, 2 POLE - 16 POSITIONS WITH 2 COMMONS |
| AFK | BINARY CODE WITH COMPLEMENT, POSITION 11 OPEN, 1 POLE - 12 POSITIONS |
| ABZ | BINARY CODE, 1 POLE - 12 POSITIONS |
| ACA | BINARY CODED DECIMAL PLUS COMPLEMENT WITH OFF POSITION, 12 POSITIONS |
| ACB | BINARY CODED WITH PARITY, 11 POSITIONS |
| ACC | BINARY CODED, 11 POSITIONS |
| ACD | BINARY COMPLEMENT ONLY, 1 POLE - 16 POSITIONS |
| ACE | BINARY WITH COMMON NOT-TRUE BITS, 2 POLE - 16 POSITIONS |
| ACF | BIQUINARY, 1 POLE - 10 POSITIONS |
| ACG | BIQUINARY, 2 POLE - 10 POSITIONS |
| ACH | CAPACITANCE DECADE, 0.001 TO 0.009 UF IN 0.001 UF STEPS |
| ACJ | CAPACITANCE DECADE, 0.01 TO 0.9 UF IN 0.01 UF STEPS |
| ACK | CAPACITANCE DECADE, 0.1 TO 0.9 UF IN 0.1 UF STEPS |
| ACL | CAPACITANCE DECADE, 1 TO 9 UF RANGE IN 1 UF STEPS |
| ACM | CAPACITANCE DECADE, 10 TO 90 UF RANGE IN 10 UF STEPS |
| ACN | COMPLEMENT CODE, 10 POSITIONS |
| ACP | COMPLEMENT OF 9'S COMPLEMENT, 1 POLE - 10 POSITIONS |
| ACR | DECIMAL, 1 POLE - 10 POSITIONS |
| ACS | DECIMAL, 1 POLE - 11 POSITIONS |
| ACT | DECIMAL, 1 POLE - 12 POSITIONS |
| ACU | DECIMAL, 1 POLE - 16 POSITIONS |
| ACQ | DECIMAL, 1 POLE - 8 POSITIONS |
| ACX | DECIMAL, 2 POLE - 10 POSITIONS |
| ACY | DECIMAL, 2 POLE - 12 POSITIONS |
| ACV | DECIMAL, 2 POLE - 5 POSITIONS |
| ACW | DECIMAL, 2 POLE - 8 POSITIONS |
| ACZ | GRAY CODE PLUS COMPLEMENT, 10 POSITIONS |
| ADA | JOHNSON CODE, 10 POSITIONS |
| ADB | MODIFIED 1242' CODE, 1 POLE - 10 POSITIONS |
| ADC | MODIFIED 1242' WITH COMPLEMENT, 1 POLE - 10 POSITIONS |
| ADD | MODIFIED 5-BIT TELETYPE, 10 POSITIONS |
| ADE | NOT/NOR SWITCH, ALL POSITIONS SHORTED EXCEPT POSITION INDICATED ON DIAL, 1 POLE - 12 POSITIONS |
| ADF | RESISTANCE DECADE, 0 TO 9 KILOHM RANGE IN 1 KILOHM STEPS |
| ADG | RESISTANCE DECADE, 0 TO 9 MEGOHM RANGE IN 1 MEGOHM STEPS |
| ADH | RESISTANCE DECADE, 0 TO 9 OHM RANGE IN 1 OHM STEPS |
| ADJ | RESISTANCE DECADE, 0 TO 90 KILOHM RANGE IN 10 KILOHM STEPS |
| ADK | RESISTANCE DECADE, 0 TO 90 OHM RANGE IN 10 OHM STEPS |
| ADL | RESISTANCE DECADE, 0 TO 900 KILOHM RANGE IN 100 KILOHM STEPS |
| ADM | RESISTANCE DECADE, 0 TO 900 OHM RANGE IN 100 OHM STEPS |
| ADN | REVERSE BCD 10 AT 0, WITH EVEN BIT PARITY, 1 POLE - 10 POSITIONS |
| ADP | SINGLE POLE CHANGEOVER SWITCH, 10 POSITIONS |
| ADQ | SINGLE POLE, SINGLE THROW, DECIMAL, ALL POSITIONS SHORTED BUT ONE, 10 POSITIONS |
| ADR | SPECIAL |
| ADU | SPECIAL 4 POLE BCD WITH COMPLEMENT, 10 POSITIONS |
| ADS | SPECIAL, 2 POLE - 2 POSITIONS |
| ADT | SPECIAL, 3 POLE - 10 POSITIONS |
| ADV | VOLTAGE DIVIDER, EECO |
| ADW | VOLTAGE DIVIDER, KELVIN VARLEY |
| ADX | VOLTAGE DIVIDER, WOLFF-POGGENDORF |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQTH*AROTOR THROUGH CONNECTION QUANTITY
INDICATES THE NUMBER OF CONNECTIONS ON A ROTOR SEGMENT THAT ARE FRONT TO REAR SURFACE CONNECTED.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(CQTH3AGKA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABM | FIRST SECTION |
| 3ABN | SECOND SECTION |
| 3ABO | THIRD SECTION |
| 3ABP | FOURTH SECTION |
| 3ABQ | FIFTH SECTION |
| 3ABR | SIXTH SECTION |
| 3ABS | SEVENTH SECTION |
| 3ABT | EIGHTH SECTION |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3AFU | NINTH SECTION |
| 3AFV | TENTH SECTION |
| 3AFW | ELEVENTH SECTION |
| 3AFX | TWELFTH SECTION |
| 3AGK | EACH SECTION |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CQDK*APILE-UP CONTACT FORM ARRANGEMENT
THE BASIC CONTACT FORMS,IN THE ORDER OF ASSEMBLAGE,THAT COLLECTIVELY DESCRIBE THE SWITCHING STRUCTURE OF A PILE-UP CONTACT GROUP.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CQDK3AQBAG1)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3APM | FIRST SWITCH FIRST SECTION FRONT |
| 3APN | FIRST SWITCH FIRST SECTION IN-LINE |
| 3APS | FIRST SWITCH SINGLE SECTION IN-LINE |
| 3APY | SECOND SWITCH SECOND SECTION IN-LINE |
| 3AQB | SECOND SWITCH SINGLE SECTION IN-LINE |
| 3AQM | SINGLE SWITCH FIRST SECTION FRONT |
| 3AQN | SINGLE SWITCH FIRST SECTION IN-LINE |
| 3AQO | SINGLE SWITCH FIRST SECTION PERIPHERY |
| 3AQP | SINGLE SWITCH SECOND SECTION IN-LINE |
| 3AQQ | SINGLE SWITCH SECOND SECTION PERIPHERY |
| 3AQV | SINGLE SWITCH SINGLE SECTION FRONT |
| 3AQW | SINGLE SWITCH SINGLE SECTION IN-LINE |
| 3AQX | SINGLE SWITCH SINGLE SECTION PERIPHERY |
| 3AQY | SINGLE SWITCH SINGLE SECTION REAR |
| 3ARA | SINGLE SWITCH EACH SECTION IN-LINE |
| 3ARI | EACH SWITCH SINGLE SECTION IN-LINE |
| 3ARM | EACH SWITCH EACH SECTION IN-LINE |
| 3ARO | EACH SWITCH EACH SECTION REAR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
CQYS*JCAM ACTUATED SWITCH CONTACT ARRANGEMENT
THE DESIGNATION INDICATING THE ELECTRICAL CONFIGURATION OF A CAM ACTUATED SWITCH INCLUDING THE NUMBER OF SWITCHING POLES OR FORMS.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit.
(CQYS3ARGJAD2*;CQYS3ARGJAD2$$JAD3*;CQYS3ARGJAD2$JAD2*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3APN | FIRST SWITCH FIRST SECTION IN-LINE |
| 3APO | FIRST SWITCH FIRST SECTION PERIPHERY |
| 3APP | FIRST SWITCH SECOND SECTION IN-LINE |
| 3APQ | FIRST SWITCH SECOND SECTION PERIPHERY |
| 3APR | FIRST SWITCH THIRD SECTION PERIPHERY |
| 3APS | FIRST SWITCH SINGLE SECTION IN-LINE |
| 3APT | FIRST SWITCH SINGLE SECTION PERIPHERY |
| 3APU | FIRST SWITCH SINGLE SECTION REAR |
| 3APV | FIRST SWITCH EACH SECTION PERIPHERY |
| 3APW | SECOND SWITCH FIRST SECTION IN-LINE |
| 3APX | SECOND SWITCH FIRST SECTION PERIPHERY |
| 3APY | SECOND SWITCH SECOND SECTION IN-LINE |
| 3APZ | SECOND SWITCH SECOND SECTION PERIPHERY |
| 3AQA | SECOND SWITCH THIRD SECTION PERIPHERY |
| 3AQC | SECOND SWITCH SINGLE SECTION PERIPHERY |
| 3AQD | SECOND SWITCH SINGLE SECTION REAR |
| 3AQE | SECOND SWITCH EACH SECTION PERIPHERY |
| 3AQF | THIRD SWITCH FIRST SECTION PERIPHERY |
| 3AQG | THIRD SWITCH SECOND SECTION PERIPHERY |
| 3AQH | THIRD SWITCH THIRD SECTION PERIPHERY |
| 3AQI | THIRD SWITCH SINGLE SECTION PERIPHERY |
| 3AQJ | FOURTH SWITCH FIRST SECTION PERIPHERY |
| 3AQK | FOURTH SWITCH SECOND SECTION PERIPHERY |
| 3AQL | SIXTH SWITCH EACH SECTION IN-LINE |
| 3AQN | SINGLE SWITCH FIRST SECTION IN-LINE |
| 3AQO | SINGLE SWITCH FIRST SECTION PERIPHERY |
| 3AQP | SINGLE SWITCH SECOND SECTION IN-LINE |
| 3AQQ | SINGLE SWITCH SECOND SECTION PERIPHERY |
| 3AQR | SINGLE SWITCH THIRD SECTION IN-LINE |
| 3AQS | SINGLE SWITCH THIRD SECTION PERIPHERY |
| 3AQT | SINGLE SWITCH FOURTH SECTION IN-LINE |
| 3AQU | SINGLE SWITCH FOURTH SECTION PERIPHERY |
| 3AQV | SINGLE SWITCH SINGLE SECTION FRONT |
| 3AQW | SINGLE SWITCH SINGLE SECTION IN-LINE |
| 3AQX | SINGLE SWITCH SINGLE SECTION PERIPHERY |
| 3AQY | SINGLE SWITCH SINGLE SECTION REAR |
| 3AQZ | SINGLE SWITCH EACH SECTION FRONT |
| 3ARA | SINGLE SWITCH EACH SECTION IN-LINE |
| 3ARB | SINGLE SWITCH EACH SECTION PERIPHERY |
| 3ARC | SINGLE SWITCH EACH SECTION REAR |
| 3ARD | EACH SWITCH FIRST SECTION IN-LINE |
| 3ARE | EACH SWITCH FIRST SECTION PERIPHERY |
| 3ARF | EACH SWITCH SECOND SECTION IN-LINE |
| 3ARG | EACH SWITCH SECOND SECTION PERIPHERY |
| 3ARH | EACH SWITCH SINGLE SECTION FRONT |
| 3ARI | EACH SWITCH SINGLE SECTION IN-LINE |
| 3ARJ | EACH SWITCH SINGLE SECTION PERIPHERY |
| 3ARK | EACH SWITCH SINGLE SECTION REAR |
| 3ARL | EACH SWITCH EACH SECTION FRONT |
| 3ARM | EACH SWITCH EACH SECTION IN-LINE |
| 3ARN | EACH SWITCH EACH SECTION PERIPHERY |
| 3ARO | EACH SWITCH EACH SECTION REAR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AG28) | Reply |
| BB | FOUR THROW, DOUBLE MAKE, NORMALLY OPEN, MOMENTARY ACTION |
| BA | FOUR THROW, NORMALLY OPEN, MOMENTARY ACTION |
| BC | FOUR WAY |
| AH | POLE, DOUBLE THROW, BOTH POSITIONS MAINTAINED |
| AL | POLE, DOUBLE THROW, DOUBLE BREAK/DOUBLE MAKE, ONE POSITION MOMENTARY |
| AJ | POLE, DOUBLE THROW, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER, BOTH POSITIONS MAINTAINED |
| AM | POLE, DOUBLE THROW, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER, ONE POSITION MOMENTARY |
| AK | POLE, DOUBLE THROW, ONE POSITION MOMENTARY |
| AP | POLE, DOUBLE THROW, ONE POSITION MOMENTARY, TWO POSITIONS MAINTAINED |
| AR | POLE, DOUBLE THROW, PERMANENT INTERNAL JUMPERS, BOTH POSITIONS MAINTAINED |
| AN | POLE, DOUBLE THROW, THREE POSITIONS MAINTAINED |
| AQ | POLE, DOUBLE THROW, TWO POSITIONS MOMENTARY |
| AA | POLE, SINGLE THROW, BOTH POSITIONS MAINTAINED |
| AB | POLE, SINGLE THROW, DOUBLE MAKE, BOTH POSITIONS MAINTAINED |
| CB | POLE, SINGLE THROW, DOUBLE MAKE, BOTH POSITIONS MAINTAINED, WITH CONTACT ON ARM |
| AC | POLE, SINGLE THROW, DUAL CONTACT, BOTH POSITIONS MAINTAINED |
| AG | POLE, SINGLE THROW, NORMALLY CLOSED, DOUBLE BREAK, MOMENTARY ACTION |
| CG | POLE, SINGLE THROW, NORMALLY CLOSED, DOUBLE BREAK, MOMENTARY ACTION, WITH CONTACT ON ARM. |
| AF | POLE, SINGLE THROW, NORMALLY CLOSED, MOMENTARY ACTION |
| AE | POLE, SINGLE THROW, NORMALLY OPEN, DOUBLE MAKE, MOMENTARY ACTION |
| CE | POLE, SINGLE THROW, NORMALLY OPEN, DOUBLE MAKE, MOMENTARY ACTION, WITH CONTACT ON ARM |
| AD | POLE, SINGLE THROW, NORMALLY OPEN, MOMENTARY ACTION |
| AS | TWO CIRCUIT, BOTH POSITIONS MAINTAINED |
| AT | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, BOTH POSITIONS MAINTAINED |
| AW | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, ONE POSITION MOMENTARY |
| AU | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER WITH NO EXTERNAL TERMINAL, BOTH POSITIONS MAINTAINED |
| AX | TWO CIRCUIT, DOUBLE BREAK/DOUBLE MAKE, PERMANENT JUMPER WITH NO EXTERNAL TERMINAL, ONE POSITION MOMENTARY |
| AZ | TWO CIRCUIT, DOUBLE MAKE, TWO POSITIONS MOMENTARY |
| AV | TWO CIRCUIT, ONE POSITION MOMENTARY |
| AY | TWO CIRCUIT, TWO POSITIONS MOMENTARY |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AKPX*APOLE QUANTITY
THE NUMBER OF POLES INCLUDED IN THE ITEM.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(AKPX3AOVA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ANO | FIRST SECTION FRONT |
| 3ANP | FIRST SECTION IN-LINE |
| 3ANQ | FIRST SECTION PERIPHERY |
| 3ANR | FIRST SECTION REAR |
| 3ANS | SECOND SECTION FRONT |
| 3ANT | SECOND SECTION IN-LINE |
| 3ANU | SECOND SECTION PERIPHERY |
| 3ANV | SECOND SECTION REAR |
| 3ANW | THIRD SECTION FRONT |
| 3ANX | THIRD SECTION IN-LINE |
| 3ANY | THIRD SECTION PERIPHERY |
| 3ANZ | THIRD SECTION REAR |
| 3AOA | FOURTH SECTION FRONT |
| 3AOB | FOURTH SECTION IN-LINE |
| 3AOC | FOURTH SECTION PERIPHERY |
| 3AOD | FOURTH SECTION REAR |
| 3AOE | FIFTH SECTION FRONT |
| 3AOF | FIFTH SECTION IN-LINE |
| 3AOG | FIFTH SECTION PERIPHERY |
| 3AOH | FIFTH SECTION REAR |
| 3AOI | SIXTH SECTION FRONT |
| 3AOJ | SIXTH SECTION PERIPHERY |
| 3AOK | SIXTH SECTION REAR |
| 3AOL | SEVENTH SECTION FRONT |
| 3AOM | SEVENTH SECTION PERIPHERY |
| 3AON | SEVENTH SECTION REAR |
| 3AOO | EIGHTH SECTION FRONT |
| 3AOP | EIGHTH SECTION PERIPHERY |
| 3AOQ | EIGHTH SECTION REAR |
| 3AOR | NINTH SECTION FRONT |
| 3AOS | NINTH SECTION IN-LINE |
| 3AOT | NINTH SECTION PERIPHERY |
| 3AOU | NINTH SECTION REAR |
| 3AOV | TENTH SECTION FRONT |
| 3AOW | TENTH SECTION PERIPHERY |
| 3AOX | TENTH SECTION REAR |
| 3AOY | ELEVENTH SECTION FRONT |
| 3APA | ELEVENTH SECTION REAR |
| 3APB | TWELFTH SECTION FRONT |
| 3APD | TWELFTH SECTION REAR |
| 3APE | SINGLE SECTION FRONT |
| 3APF | SINGLE SECTION IN-LINE |
| 3APG | SINGLE SECTION PERIPHERY |
| 3APH | SINGLE SECTION REAR |
| 3API | EACH SECTION FRONT |
| 3APJ | EACH SECTION IN-LINE |
| 3APK | EACH SECTION PERIPHERY |
| 3APL | EACH SECTION REAR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AKPY*ATHROW QUANTITY
THE NUMBER OF POSITIONS TO WHICH THE ITEM MAY BE ACTUATED TO ENERGIZE ELECTRICAL CIRCUITS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a numeric reply with a minimum of one digit.
(AKPY3AOUA10)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ANO | FIRST SECTION FRONT |
| 3ANP | FIRST SECTION IN-LINE |
| 3ANQ | FIRST SECTION PERIPHERY |
| 3ANR | FIRST SECTION REAR |
| 3ANS | SECOND SECTION FRONT |
| 3ANT | SECOND SECTION IN-LINE |
| 3ANU | SECOND SECTION PERIPHERY |
| 3ANV | SECOND SECTION REAR |
| 3ANW | THIRD SECTION FRONT |
| 3ANY | THIRD SECTION PERIPHERY |
| 3ANZ | THIRD SECTION REAR |
| 3AOA | FOURTH SECTION FRONT |
| 3AOC | FOURTH SECTION PERIPHERY |
| 3AOD | FOURTH SECTION REAR |
| 3AOE | FIFTH SECTION FRONT |
| 3AOG | FIFTH SECTION PERIPHERY |
| 3AOH | FIFTH SECTION REAR |
| 3AOI | SIXTH SECTION FRONT |
| 3AOJ | SIXTH SECTION PERIPHERY |
| 3AOK | SIXTH SECTION REAR |
| 3AOL | SEVENTH SECTION FRONT |
| 3AOM | SEVENTH SECTION PERIPHERY |
| 3AON | SEVENTH SECTION REAR |
| 3AOO | EIGHTH SECTION FRONT |
| 3AOP | EIGHTH SECTION PERIPHERY |
| 3AOQ | EIGHTH SECTION REAR |
| 3AOR | NINTH SECTION FRONT |
| 3AOU | NINTH SECTION REAR |
| 3AOV | TENTH SECTION FRONT |
| 3AOX | TENTH SECTION REAR |
| 3AOY | ELEVENTH SECTION FRONT |
| 3APA | ELEVENTH SECTION REAR |
| 3APB | TWELFTH SECTION FRONT |
| 3APD | TWELFTH SECTION REAR |
| 3APE | SINGLE SECTION FRONT |
| 3APF | SINGLE SECTION IN-LINE |
| 3APG | SINGLE SECTION PERIPHERY |
| 3APH | SINGLE SECTION REAR |
| 3API | EACH SECTION FRONT |
| 3APJ | EACH SECTION IN-LINE |
| 3APK | EACH SECTION PERIPHERY |
| 3APL | EACH SECTION REAR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CSHW*DCONTACT SWITCHING ACTION
AN INDICATION OF THE SWITCHING ACTION BY THE CONTACTS OF THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CSHW3AOQDC*;CSHW3AOQDC$DB*;CSHW3AOQDC$$DB*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ANO | FIRST SECTION FRONT |
| 3ANP | FIRST SECTION IN-LINE |
| 3ANQ | FIRST SECTION PERIPHERY |
| 3ANR | FIRST SECTION REAR |
| 3ANS | SECOND SECTION FRONT |
| 3ANT | SECOND SECTION IN-LINE |
| 3ANU | SECOND SECTION PERIPHERY |
| 3ANV | SECOND SECTION REAR |
| 3ANW | THIRD SECTION FRONT |
| 3ANX | THIRD SECTION IN-LINE |
| 3ANY | THIRD SECTION PERIPHERY |
| 3ANZ | THIRD SECTION REAR |
| 3AOA | FOURTH SECTION FRONT |
| 3AOB | FOURTH SECTION IN-LINE |
| 3AOC | FOURTH SECTION PERIPHERY |
| 3AOD | FOURTH SECTION REAR |
| 3AOE | FIFTH SECTION FRONT |
| 3AOF | FIFTH SECTION IN-LINE |
| 3AOG | FIFTH SECTION PERIPHERY |
| 3AOH | FIFTH SECTION REAR |
| 3AOI | SIXTH SECTION FRONT |
| 3AOJ | SIXTH SECTION PERIPHERY |
| 3AOK | SIXTH SECTION REAR |
| 3AOL | SEVENTH SECTION FRONT |
| 3AOM | SEVENTH SECTION PERIPHERY |
| 3AON | SEVENTH SECTION REAR |
| 3AOO | EIGHTH SECTION FRONT |
| 3AOP | EIGHTH SECTION PERIPHERY |
| 3AOQ | EIGHTH SECTION REAR |
| 3AOR | NINTH SECTION FRONT |
| 3AOT | NINTH SECTION PERIPHERY |
| 3AOU | NINTH SECTION REAR |
| 3AOV | TENTH SECTION FRONT |
| 3AOW | TENTH SECTION PERIPHERY |
| 3AOX | TENTH SECTION REAR |
| 3AOY | ELEVENTH SECTION FRONT |
| 3AOZ | ELEVENTH SECTION PERIPHERY |
| 3APA | ELEVENTH SECTION REAR |
| 3APB | TWELFTH SECTION FRONT |
| 3APC | TWELFTH SECTION PERIPHERY |
| 3APD | TWELFTH SECTION REAR |
| 3APE | SINGLE SECTION FRONT |
| 3APF | SINGLE SECTION IN-LINE |
| 3APG | SINGLE SECTION PERIPHERY |
| 3APH | SINGLE SECTION REAR |
| 3API | EACH SECTION FRONT |
| 3APJ | EACH SECTION IN-LINE |
| 3APK | EACH SECTION PERIPHERY |
| 3APL | EACH SECTION REAR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD78) | Reply |
| C | BREAKS BEFORE MAKES |
| B | MAKES BEFORE BREAKS |
| D | MAKES BEFORE BREAKS, BREAKS BEFORE MAKES |
CSLC*JSWITCH ACTUATOR POSITIONING INCREMENT
THE INCREMENTS OF ANGULAR ROTATION THAT THE SWITCH ACTUATOR MOVES BETWEEN ADJACENT INDEX POSITIONS.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CSLC3ALZJR2.0*;CSLC3ALZJR2.0$JR2.0*;CSLC3ALZJR2.0$$JR2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMA | FOURTH ACTUATOR |
| 3AMB | FIFTH ACTUATOR |
| 3AMC | SIXTH ACTUATOR |
| 3AMD | SEVENTH ACTUATOR |
| 3AMF | NINTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
CQQT*DSWITCH ACTUATOR MOMENTARY POSITION
THE POSITION OF THE ACTUATOR,WITH RELATION TO THE EXTREMITY OF ROTATION,THAT IS MOMENTARY (SPRING LOADED).
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CQQT3AEEDB*;CQQT3AEEDB$DC*;CQQT3AEEDB$$DC*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AC84) | Reply |
| B | CLOCKWISE |
| C | COUNTERCLOCKWISE |
CTDN*DSWITCH ACTUATOR STOP DEVICE TYPE
INDICATES THE TYPE OF DEVICE INCLUDED IN THE SWITCH TO LIMIT THE ANGULAR ROTATION OF ITS ACTUATOR.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CTDN3AMKDB*;CTDN3AMKDB$DE*;CTDN3AMKDB$$DE*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMA | FOURTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD89) | Reply |
| D | ADJUSTABLE STOP |
| B | FIXED STOP |
| C | FIXED STOP-BREAKOFF TAB |
| E | FIXED-ADJUSTABLE STOPS |
CRSJ*DSHAFT TYPE
INDICATES THE TYPE OF SHAFT INCLUDED ON THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CRSJ3AEEDEM*;CRSJ3AEEDEM$DDJ*;CRSJ3AEEDEM$$DDJ*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AF58) | Reply |
| FA | RECTANGULAR/SQUARE, THREADED HOLE |
| BM | ROUND |
| DR | ROUND W/THROUGH HOLE |
| CP | ROUND, BREAKOFF |
| CQ | ROUND, CROSS SLOTTED |
| CR | ROUND, FLAT, UNDERCUT |
| BZ | ROUND, FLATTED |
| DZ | ROUND, FLATTED W/THROUGH HOLE |
| CS | ROUND, FLATTED, THREADED HOLE |
| CT | ROUND, FLUTED |
| CW | ROUND, FLUTED, THREADED HOLE |
| CX | ROUND, HOLLOWED |
| CY | ROUND, HOLLOWED, FLATTED |
| CZ | ROUND, HOLLOWED, SLOTTED |
| DY | ROUND, KNURLED |
| DA | ROUND, MILLED, SPRING SLIT |
| DB | ROUND, NONPARALLEL FLATTED |
| DC | ROUND, PARALLEL FLATTED |
| DD | ROUND, PARALLEL FLATTED, THREADED HOLE |
| DE | ROUND, SLOTTED |
| EA | ROUND, SLOTTED, FLAT UNDERCUT |
| DF | ROUND, SLOTTED, FLATTED |
| EB | ROUND, SLOTTED, KNURLED |
| DG | ROUND, SLOTTED, PARALLEL FLATTED |
| DN | ROUND, SLOTTED, UNDERCUT |
| DH | ROUND, SQUARE |
| EC | ROUND, SQUARE, CHANNELLED |
| ED | ROUND, SQUARE, SLOTTED |
| DJ | ROUND, SQUARE, THREADED HOLE |
| DW | ROUND, THREADED |
| EL | ROUND, THREADED HOLE |
| EM | ROUND, TRIPLE FLAT |
| EN | ROUND, TRIPLE FLAT, THREADED HOLE |
| DM | ROUND, UNDERCUT |
| EE | ROUND, V CHANNELLED |
| DK | ROUND, V FLATTED |
AATB*JWIDTH BETWEEN FLATS
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AATB3AMGJAA2.0*;AATB3AMGJAA2.0$JAA2.0*;AATB3AMGJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALY | SECOND ACTUATOR |
| 3AMG | TENTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNB*JFIRST FLAT LENGTH
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNB3ALXJLA2.0*;ABNB3ALXJLA2.0$JLA2.0*;ABNB3ALXJLA2.0$$JLA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3AMG | TENTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABNC*JFLAT HEIGHT
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABNC3ALYJLC2.0*;ABNC3ALYJLC2.0$JLC2.0*;ABNC3ALYJLC2.0$$JLC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABWV*JSHAFT DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF A SHAFT,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABWV3AMGJAA2.0*;ABWV3AMGJAA2.0$JAA2.0*;ABWV3AMGJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMG | TENTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABXF*JSHAFT LENGTH
A MEASUREMENT OF THE LONGEST DIMENSION OF THE SHAFT,IN DISTINCTION FROM WIDTH.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABXF3ALYJLB2.0*;ABXF3ALYJLB2.0$JLB2.0*;ABXF3ALYJLB2.0$$JLB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMC | SIXTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CRTY*JSQUARE SHAFT SIZE
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CRTY3ALXJAC2.0*;CRTY3ALXJAC2.0$JAC2.0*;CRTY3ALXJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CZGW*JLARGEST SHAFT WIDTH
NONE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CZGW3AEEJLB2.0*;CZGW3AEEJLB2.0$JLB2.0*;CZGW3AEEJLB2.0$$JLB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3AMJ | SINGLE ACTUATOR |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) D, E OR F WERE ENTERED FOR MRC AFDC, YOU MUST ANSWER MRC (AEFP)
AFDC*DNONTURN DEVICE TYPE
INDICATES THE TYPE OF DEVICE USED TO PREVENT PHYSICAL MOVEMENT OF THE ITEM ON ITS MOUNTING SURFACE.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AFDC3ASPDB*;AFDC3ASPDB$DD*;AFDC3ASPDB$$DD*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASB | AT 1:00 OCLOCK |
| 3ASC | AT 1:30 OCLOCK |
| 3ASD | AT 1:45 OCLOCK |
| 3ASE | AT 2:00 OCLOCK |
| 3ASF | AT 2:30 OCLOCK |
| 3ASG | AT 2:45 OCLOCK |
| 3ASH | AT 3:00 OCLOCK |
| 3ASI | AT 4:00 OCLOCK |
| 3ASJ | AT 4:30 OCLOCK |
| 3ASK | AT 5:00 OCLOCK |
| 3ASL | AT 6:00 OCLOCK |
| 3ASM | AT 7:00 OCLOCK |
| 3ASN | AT 7:30 OCLOCK |
| 3ASO | AT 8:00 OCLOCK |
| 3ASP | AT 8:30 OCLOCK |
| 3ASQ | AT 9:00 OCLOCK |
| 3ASR | AT 9:30 OCLOCK |
| 3ASS | AT 10:00 OCLOCK |
| 3AST | AT 10:30 OCLOCK |
| 3ASU | AT 11:00 OCLOCK |
| 3ASV | AT 11:30 OCLOCK |
| 3ASW | AT 12:00 OCLOCK |
| 3ASX | AT 12:15 OCLOCK |
| 3ASY | AT 12:30 OCLOCK |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD95) | Reply |
| C | FLATTED BUSHING |
| F | KEY |
| D | PIN |
| B | SLOTTED BUSHING |
| E | TAB |
AEFP*JNONTURN DEVICE RADIUS
THE LINEAR MEASUREMENT OF THE DISTANCE FROM THE ACTUATOR CENTERLINE TO THE CENTERLINE OF THE NONTURN DEVICE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEFP3ASIJLC2.0*;AEFP3ASIJLC2.0$JLC2.0*;AEFP3ASIJLC2.0$$JLC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASB | AT 1:00 OCLOCK |
| 3ASC | AT 1:30 OCLOCK |
| 3ASD | AT 1:45 OCLOCK |
| 3ASE | AT 2:00 OCLOCK |
| 3ASF | AT 2:30 OCLOCK |
| 3ASG | AT 2:45 OCLOCK |
| 3ASH | AT 3:00 OCLOCK |
| 3ASI | AT 4:00 OCLOCK |
| 3ASJ | AT 4:30 OCLOCK |
| 3ASK | AT 5:00 OCLOCK |
| 3ASL | AT 6:00 OCLOCK |
| 3ASM | AT 7:00 OCLOCK |
| 3ASN | AT 7:30 OCLOCK |
| 3ASO | AT 8:00 OCLOCK |
| 3ASP | AT 8:30 OCLOCK |
| 3ASQ | AT 9:00 OCLOCK |
| 3ASR | AT 9:30 OCLOCK |
| 3ASS | AT 10:00 OCLOCK |
| 3AST | AT 10:30 OCLOCK |
| 3ASU | AT 11:00 OCLOCK |
| 3ASV | AT 11:30 OCLOCK |
| 3ASW | AT 12:00 OCLOCK |
| 3ASY | AT 12:30 OCLOCK |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) ACQ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AEBV)
IF STYLE/REPLY CODE(s) ABY WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (ABTD)
IF STYLE/REPLY CODE(s) AET, AFA OR AJZ WERE ENTERED FOR MRC AXGY, YOU MUST ANSWER MRC (AASA)
AXGY*DMOUNTING METHOD
THE MEANS OF ATTACHING THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(AXGY3ASZDABB*;AXGY3ASZDABB$DABC*;AXGY3ASZDABB$$DABC*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AM39) | Reply |
| ABB | BASE |
| ABC | BRACKET |
| ACR | FLANGE |
| ADC | PRESS FIT |
| AEZ | PRINTED CIRCUIT |
| ABW | SCREW |
| ABY | SLOT |
| AJR | STRUT |
| ACD | TERMINAL |
| AFA | THREADED BUSHING |
| AJZ | THREADED BUSHING W/PANEL SEAL |
| AHF | THREADED HOLE |
| AET | THREADED STUD |
| ACQ | UNTHREADED HOLE |
AEBV*JUNTHREADED MOUNTING HOLE DIAMETER
THE LENGTH OF A STRAIGHT LINE WHICH PASSES THROUGH THE CENTER OF AN UNTHREADED MOUNTING HOLE,AND TERMINATES AT THE CIRCUMFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEBV3ATAJLC2.0*;AEBV3ATAJLC2.0$JLC2.0*;AEBV3ATAJLC2.0$$JLC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ABTD*JMOUNTING SLOT WIDTH
A MEASUREMENT TAKEN AT RIGHT ANGLES TO THE LENGTH OF THE MOUNTING SLOT,IN DISTINCTION FROM THICKNESS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ABTD3AEEJLB2.0*;ABTD3AEEJLB2.0$JLB2.0*;ABTD3AEEJLB2.0$$JLB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AASA*JTHREAD LENGTH
A MEASUREMENT OF THE EXTENT OF THREADS,INCLUDING INCOMPLETE THREADS,ALONG A LINE PARALLEL TO THE LONGITUDINAL AXIS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AASA3AEEJLC2.0*;AASA3AEEJLC2.0$JLC2.0*;AASA3AEEJLC2.0$$JLC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
IF STYLE/REPLY CODE(s) SM OR SS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CQQR) or (CQJX and CTTC) or (CQJX and AAJE)
IF STYLE/REPLY CODE(s) NC OR UN WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD)
IF STYLE/REPLY CODE(s) JC, JE, JF, NE, NF OR NJ WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and AAJD)
IF STYLE/REPLY CODE(s) NM WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP) or (CQJX and CQQR)
IF STYLE/REPLY CODE(s) NS WERE ENTERED FOR MRC THSD, YOU MUST ANSWER MRC (CQJX and CMLP and AAJD) or (CQJX and CMLP and AAJE)
THSD*DTHREAD SERIES DESIGNATOR
A DESIGNATION DISTINGUISHING ONE GROUP OF THREAD DIAMETER-PITCH COMBINATIONS FROM ANOTHER BY THE NUMBER OF THREADS PER MEASUREMENT SCALE FOR A SPECIFIC DIAMETER.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(THSD3ATDDJE*;THSD3ATDDJE$DUN*;THSD3ATDDJE$$DUN*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AH06) | Reply |
| SM | ISO M |
| SS | ISO S |
| UN | UN |
| NC | UNC |
| NE | UNEF |
| NF | UNF |
| NJ | UNJ |
| JC | UNJC |
| JE | UNJEF |
| JF | UNJF |
| NM | UNM |
| NS | UNS |
CQJX*JNOMINAL THREAD SIZE
A DESIGNATION THAT IS USED FOR THE PURPOSE OF GENERAL IDENTIFICATION OF THE THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQJX3ATBJA2.0*;CQJX3ATBJA2.0$JA2.0*;CQJX3ATBJA2.0$$JA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
AAJD*ATHREAD CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING THE PITCH DIAMETER TOLERANCE AND AN EXTERNAL OR INTERNAL THREAD.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(AAJD3ATAAJ0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CTTC*JTHREAD TOLERANCE CLASS
A NUMERIC-ALPHA DESIGNATOR INDICATING ESTABLISHED PITCH AND CREST DIAMETER TOLERANCE POSITION AND GRADE.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a alpha-numeric reply with a minimum of one character.
(CTTC3AEEJEXT2.0*;CTTC3AEEJEXT2.0$JEXT2.0*;CTTC3AEEJEXT2.0$$JEXT2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AN73) | Reply |
| EXT | EXTERNAL |
| NTE | INTERNAL |
CMLP*ATHREAD QUANTITY PER INCH
THE NUMBER OF THREADS ON THE ITEM PER LINEAR INCH MEASURED ON A LINE PARALLEL TO THE THREAD AXIS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a alpha-numeric reply with a minimum of one character.
(CMLP3ASZAJ6)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CQQR*BTHREAD PITCH IN MILLIMETERS
A MEASUREMENT OF DISTANCE BETWEEN CORRESPONDING POINTS ON TWO ADJACENT THREADS MEASURED PARALLEL TO THE THREAD AXIS,EXPRESSED IN MILLIMETERS.
Enter the applicable ISAC from the table below followed by the mode code, followed by a reply with a minimum of one digit on either side of the decimal point.
(CQQR3AEEB2.0)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
AAJE*JTHREAD PITCH DIAMETERS
THE MINIMUM AND MAXIMUM PITCH DIAMETER LIMITS OF A STRAIGHT SCREW THREAD.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AAJE3AEEJAM32.0/P50.0*;AAJE3AEEJAM32.0/P50.0$$JA*;AAJE3AEEJAM32.0/P50.0$JAM32.0/P50.0*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
CQYJ*DMOUNTING FACILITY PATTERN
THE GENERAL CONFIGURATION AND RELATIVE POSITION OF THE FACILITIES PROVIDED FOR MOUNTING THE ITEM.
Enter the applicable ISAC from Table 1 below followed by the mode code and applicable Reply Code from Table 2
(CQYJ3ATADBT*;CQYJ3ATADBT$DBY*;CQYJ3ATADBT$$DBY*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AD96) | Reply |
| CA | EIGHT POSITION CIRCULAR |
| BW | EIGHT POSITION RECTANGULAR |
| BY | FOUR POSITION CIRCULAR |
| BS | FOUR POSITION DIAMOND |
| BN | FOUR POSITION IN-LINE |
| CD | FOUR POSITION PARALLELOGRAM |
| BP | FOUR POSITION RECTANGULAR |
| CE | FOUR POSITION TRAPEZOID |
| BT | ISOSCELES TRIANGLE |
| CF | OBTUSE TRIANGLE |
| BZ | SIX POSITION CIRCULAR |
| CG | SIX POSITION PARALLELOGRAM |
| BR | SIX POSITION RECTANGULAR |
| BX | THREE POSITION CIRCULAR |
| BM | THREE POSITION IN-LINE |
| BQ | TWO POSITION DIAGONAL |
| BL | TWO POSITION IN-LINE |
Reference Notes Refer to Reference Drawings for assitance in answering this MRC.
AEJN*JDISTANCE BETWEEN MOUNTING FACILITY CENTERS
THE DISTANCE BETWEEN MOUNTING FACILITY CENTERS.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AEJN3ATAJAA2.0*;AEJN3ATAJAA2.0$JAA2.0*;AEJN3ATAJAA2.0$$JAA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATC | FOURTH MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDS*JLONGEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDS3AEEJLA2.0*;AFDS3AEEJLA2.0$JLA2.0*;AFDS3AEEJLA2.0$$JLA2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDT*JSHORTEST HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDT3ASZJLB2.0*;AFDT3ASZJLB2.0$JLB2.0*;AFDT3ASZJLB2.0$$JLB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDU*JINTERMEDIATE HORIZONTAL DISTANCE BETWEEN MOUNTING CENTERS
THE INTERMEDIATE DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE HORIZONTAL PLANE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDU3ASZJAC2.0*;AFDU3ASZJAC2.0$JAC2.0*;AFDU3ASZJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDV*JLONGEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS
THE LONGEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDV3ASZJLC2.0*;AFDV3ASZJLC2.0$JLC2.0*;AFDV3ASZJLC2.0$$JLC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
AFDW*JSHORTEST VERTICAL DISTANCE BETWEEN MOUNTING CENTERS
THE SHORTEST DISTANCE BETWEEN MOUNTING CENTERS PARALLEL TO THE VERTICAL PLANE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(AFDW3ATDJAC2.0*;AFDW3ATDJAC2.0$JAC2.0*;AFDW3ATDJAC2.0$$JAC2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
ALAQ*JMOUNTING FACILITY CIRCLE RADIUS
THE RADIUS OF THE CIRCLE IN WHICH THE MOUNTING FACILITIES OF AN ITEM ARE LOCATED.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(ALAQ3ATDJAB2.0*;ALAQ3ATDJAB2.0$JAB2.0*;ALAQ3ATDJAB2.0$$JAB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ASZ | FIRST MOUNTING FACILITY |
| 3ATA | SECOND MOUNTING FACILITY |
| 3ATB | THIRD MOUNTING FACILITY |
| 3ATD | SINGLE MOUNTING FACILITY |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA05) | Reply |
| A | INCHES |
| L | MILLIMETERS |
| Table 3 |
| Reply Code (AC20) | Reply |
| A | NOMINAL |
| B | MINIMUM |
| C | MAXIMUM |
CBBL*DFEATURES PROVIDED
THOSE FEATURES,NOT OTHERWISE SPECIFIED,WHICH MAY BE REQUIRED FOR PROPER FUNCTIONING OF THE ITEM.
Enter the applicable reply code from the table below
(CBBLDFNY*;CBBLDCLY$$DCMC*)
| Table 1 |
| Reply Code (AN47) | Reply |
| AND | ACTUATOR KNOB |
| BDR | ARC QUENCHING |
| CLW | CAM ACTUATED |
| CLX | DUMMY CONTACT |
| CLY | DUMMY SECTION |
| CLZ | DUMMY TERMINAL |
| CMA | ILLUMINATED |
| CMB | LEGEND PLATE |
| CMC | METALLIC INCLOSURE |
| CMD | PULL TO TURN |
| CME | PUSH TO TURN |
| AGQ | RFI SHIELDING |
| FNY | ROHS DIRECTIVE COMPLIANCE |
| CMF | SHAFT COUPLER |
| CMG | SHAFT THROUGH PIN |
| CMH | SPRING RETURN |
| ANF | VARIABLE RESISTOR |
| ANG | VARIABLE RESISTOR PROVISIONS |
| BPW | W/GEAR |
ENAC*DENVIRONMENTAL ATTRIBUTE CODE
INDICATES THE TYPE OF PRODUCT THAT MEETS OR EXCEEDS THE GOVERNMENT GUIDELINES FOR ENVIRONMENTALLY PREFERRED CHARACTERISTICS.
Enter the applicable reply code from the table below
(ENACDQH*;ENACDQD$DAK*;ENACDQD$$DAK*)
| Table 1 |
| Reply Code (EN02) | Reply |
| QD | HEXAVALENT CHROMIUM ALTERNATIVE |
| AK | NON-CADMIUM PRODUCT |
| QH | NON-LEAD ALTERNATIVE PRODUCTS |
TEST*JTEST DATA DOCUMENT
THE SPECIFICATION,STANDARD,DRAWING,OR SIMILAR INSTRUMENT THAT SPECIFIES ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS OR TEST CONDITIONS UNDER WHICH AN ITEM IS TESTED AND ESTABLISHES ACCEPTABLE LIMITS WITHIN WHICH THE ITEM MUST CONFORM IDENTIFIED BY AN ALPHABETIC AND/OR NUMERIC REFERENCE NUMBER. INCLUDES THE COMMERCIAL AND GOVERNMENT ENTITY (CAGE) CODE OF THE ENTITY CONTROLLING THE INSTRUMENT.
Enter the applicable Reply Code from the table below, followed by the 5-position CAGE Code, a dash, and the document identification number.
(TESTJA12345-CWX654321*; TESTJA1234A-654321$$JB5556A-663654*; TESTJAA2345-654321$JB55566-663654*)
| Table 1 |
| Reply Code (AC28) | Reply |
| A | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| B | STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| C | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
SPCL*GSPECIAL TEST FEATURES
TEST CONDITIONS AND RATINGS OR ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS THAT ARE DIFFERENT, MORE CRITICAL, OR MORE SPECIFIC THAN THOSE SPECIFIED IN A GOVERNING TEST DATA DOCUMENT.
Enter the reply in clear text.
(SPCLGSELECTED AND TESTED FOR NAVIGATIONAL SYSTEMS*)
ZZZV*GFSC APPLICATION DATA
THE JUSTIFICATION FOR THE ASSIGNMENT OF A FEDERAL SUPPLY CLASS /FSC/ TO AN ITEM BASED ON THE CLASSIFICATION OF THE NEXT HIGHER CLASSIFIABLE ASSEMBLY.
Enter the name of the next higher classifiable assembly in clear text.
(ZZZVGFUEL SYSTEM, GASOLINE ENGINE, NONAIRCRAFT*)
ZZZW*GDEPARTURE FROM CITED DOCUMENT
THE TECHNICAL DIFFERENTIATING CHARACTERISTIC(S) OF AN ITEM OF SUPPLY THAT DEPART(S) FROM THE TEXT OF A SPECIFICATION OR A STANDARD IN THAT IT REPRESENTS A SELECTION OF CHARACTERISTICS STATED IN THE SPECIFICATION OR STANDARD AS BEING OPTIONAL OR A VARIATION FROM ONE OR MORE OF THE STATED CHARACTERISTICS OR AN ADDITIONAL CHARACTERISTIC NOT STATED IN THE SPECIFICATION OR STANDARD.
Enter the reply in clear text.
(ZZZWGAS MODIFIED BY MATERIAL*)
ZZZX*GDEPARTURE FROM CITED DESIGNATOR
THE VARIATION WHEN THE ITEM IS IN CONFORMITY WITH A TYPE DESIGNATOR COVERED BY A SPECIFICATION OR STANDARD, EXCEPT IN REGARD TO ONE OR MORE TECHNICAL DIFFERENTIATING CHARACTERISTICS.
Enter the reply in clear text.
(ZZZXGAS MODIFIED BY MATERIAL*)
NHCF*DNUCLEAR HARDNESS CRITICAL FEATURE
AN INDICATION OF THE NUCLEAR HARDNESS CRITICALITY OF THE ITEM.
Enter the applicable reply code from the table below
(NHCFDCY)
| Table 1 |
| Reply Code (AD05) | Reply |
| CY | HARDENED |
ELCD*DEXTRA LONG CHARACTERISTIC DESCRIPTION
A DESCRIPTION THAT EXCEEDS 5000 CHARACTERS.
Enter the Reply Code from the table below.
(ELCDDA*)
| Table 1 |
| Reply Code (AN58) | Reply |
| A | ADDITIONAL DESCRIPTIVE DATA ON MANUAL RECORD |
ABFE*DHAZARDOUS LOCATIONS/ENVIRONMENTAL PROTECTION
THE SPECIFIC COMMERCIAL RATING WHICH CLASSES THE ITEM AS TO WHAT DEGREE THE ITEM WILL WITHSTAND ENVIRONMENTAL ELEMENTS AND/OR HAZARDOUS LOCATIONS.
Enter the applicable reply code from the table below
(ABFEDEP*;ABFEDEM$$DFM*)
| Table 1 |
| Reply Code (AB27) | Reply |
| ED | CORROSION PROOF |
| DJ | CORROSION RESISTANT |
| CG | DRIPPROOF |
| FS | DRIPTIGHT |
| EF | DUST RESISTANT |
| CF | DUSTPROOF |
| DY | DUSTTIGHT |
| CE | EXPLOSION PROOF |
| FQ | EXPLOSION RESISTANT |
| DK | FUNGUS PROOF |
| CH | FUNGUS RESISTANT |
| EB | HERMETICALLY SEALED |
| GE | HUMIDITY RESISTANT |
| DV | MOISTURE PROOF |
| BR | MOISTURE RESISTANT |
| DW | OIL RESISTANT |
| CJ | OILTIGHT |
| CK | RAINPROOF |
| EM | RAINTIGHT |
| GC | SALT SPRAY PROOF |
| FZ | SALT SPRAY RESISTANT |
| DT | SALT WATER RESISTANT |
| FY | SAND PROOF |
| EN | SANDTIGHT |
| EJ | SHOCK PROOF |
| EP | SHOCK RESISTANT |
| BT | SPLASHPROOF |
| CL | SPRAYTIGHT |
| FM | VIBRATION PROOF |
| GB | VIBRATION RESISTANT |
| EA | WATER RESISTANT |
| CM | WATERPROOF |
| CN | WATERTIGHT |
| EG | WEATHER RESISTANT |
| DX | WEATHERPROOF |
| GG | WEATHERTIGHT |
AFCZ*GKNOB SPECIAL MARKINGS
MARKINGS INCLUDED ON THE KNOB FOR THE PURPOSE OF OFFERING INSTRUCTIONS OR WARNINGS OR TO INDICATE THE PURPOSE,FUNCTION,OR APPLICATION OF THE ITEM. EXCLUDES MANUFACTURERS PART NUMBER,SYMBOLS,OR THE LIKE.
Enter clear text.
(AFCZGCLEARTEXT)
AFCQ*AKNOB MANUFACTURER CODE
THE IDENTIFYING CODE OF THE ORGINATOR THAT CONTROLS OR MANUFACTURERS THE KNOB.
Enter the alpha-numeric reply with five character(s) exactly.
(AFCQAJ5A4D)
AFCY*AKNOB MANUFACTURER PART NUMBER
THE IDENTIFYING PART NUMBER ASSIGNED TO THE KNOB.
Enter the alpha-numeric reply with a minimum of one character.
(AFCYAL0)
CQRQ*JSHAFT FLAT/SLOT ANGULAR LOCATION
THE ANGULAR DISTANCE OF THE SHAFT FLAT OR SLOT FROM THE POINT OF REFERENCE.
Enter the applicable ISAC from Table 1 below followed by the mode code, the applicable Reply Code from Tables 2 & 3 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CQRQ3AEEJRB2.0*;CQRQ3AEEJRB2.0$JRB2.0*;CQRQ3AEEJRB2.0$$JRB2.1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AP38) | Reply |
| D | DEGREES |
| R | RADIANS |
| Table 3 |
| Reply Code (AD94) | Reply |
| C | FROM CONTACT POSITION 1 |
| B | FROM NONTURN DEVICE |
AFGA*JOPERATING TEMP RANGE
THE MINIMUM AND MAXIMUM LIMITS OF TEMPERATURE AT WHICH THE ITEM IS RATED FOR OPERATION.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(AFGAJCM32.0/P50.0*)
| Table 1 |
| Reply Code (AB36) | Reply |
| C | CELSIUS |
| F | FAHRENHEIT |
CSMW*JDETENT ROTATIONAL TORQUE RANGE
THE MINIMUM AND MAXIMUM AMOUNT OF TURNING FORCE REQUIRED TO ROTATE AN ACTUATOR THROUGH THE DETENT POSITIONS.
Enter the applicable ISAC from Table 1 below followed by the mode code, applicable Reply Code from Table 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit. Precede negative values (below zero degrees) with the letter M, and positive values (zero and above) with the letter P.
(CSMW3ALYJDM32.0/P50.0*;CSMW3ALYJDM32.0/P50.0$$JD*;CSMW3ALYJDM32.0/P50.0$JDM32.0/P50.0*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3AEE | OVERALL |
| 3ALX | FIRST ACTUATOR |
| 3ALY | SECOND ACTUATOR |
| 3ALZ | THIRD ACTUATOR |
| 3AMD | SEVENTH ACTUATOR |
| 3AMJ | SINGLE ACTUATOR |
| 3AMK | ALL ACTUATORS |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
| Table 2 |
| Reply Code (AA56) | Reply |
| D | CENTIMETER-GRAMS |
| A | INCH-OUNCES |
| G | INCH-POUNDS |
PRMT*DPRECIOUS MATERIAL
IDENTIFICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM.
Enter the applicable reply code from the table below
(PRMTDAZA000*;PRMTDRHA000$DRTA000*;PRMTDRHA000$$DRTA000*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
PMWT*JPRECIOUS MATERIAL AND WEIGHT
AN INDICATION OF THE PRECIOUS MATERIAL CONTAINED IN THE ITEM,AND THE AMOUNT PER A MEASUREMENT SCALE.
Enter the applicable Reply Code from Tables 1 & 2 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(PMWTJIRA000R2.0*;PMWTJIRA000R2.0$JIRA000R2.0*;PMWTJIRA000R2.0$$JIRA000R2.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
| Table 2 |
| Reply Code (AG14) | Reply |
| C | CARAT |
| E | GRAINS, TROY |
| R | GRAMS |
| F | OUNCES, TROY |
PMLC*JPRECIOUS MATERIAL AND LOCATION
AN INDICATION OF THE PRECIOUS MATERIAL AND ITS LOCATION IN THE ITEM.
Enter the applicable Reply Code from Table 1 below followed by a alpha-numeric reply with a minimum of one character.
(PMLCJPDA0002.0*;PMLCJPDA0002.0$JPDA0002.0*;PMLCJPDA0002.0$$JPDA0002.1*)
| Table 1 |
| Reply Code (MA01) | Reply |
| AUA000 | GOLD |
| IRA000 | IRIDIUM |
| AZA000 | OSMIUM |
| PDA000 | PALLADIUM |
| PTA000 | PLATINUM |
| RHA000 | RHODIUM |
| RTA000 | RUTHENIUM |
| AGA000 | SILVER |
CBME*JCUBIC MEASURE
A MEASUREMENT OF VOLUME TAKEN BY MULTIPLYING THE LENGTH BY THE WIDTH BY THE HEIGHT OF AN ITEM AND RENDERED IN CUBIC UNITS.
Enter the applicable Reply Code from Table 1 below followed by a numeric reply with a minimum of one digit, a decimal and a minimum of one digit.
(CBMEJCN2.0*)
| Table 1 |
| Reply Code (AN76) | Reply |
| CC | CUBIC CENTIMETERS |
| CN | CUBIC INCHES |
This MRC replaced MRC ZZZP
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
PDNB*APURCHASE DESCRIPTION IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF A DOCUMENT USED IN LIEU OF A SPECIFICATION IN THE PROCUREMENT OF AN ITEM OF SUPPLY.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document, followed by a dash and the identifying number of the document.
(PDNBA81A37-30624A*)
SUPP*GSUPPLEMENTARY FEATURES
CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN ANY OTHER REQUIREMENT THAT ARE CONSIDERED ESSENTIAL INFORMATION FOR ONE OR MORE FUNCTIONS, EXCLUDING NSN ASSIGNMENT.
Enter the reply in clear text.Separate multiple replies with a semicolon.
(SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT* SUPPGMAY INCL HOLE IN UPPER SUPPORT FOR MTG DURING SHIPMENT; BLADE TIEDOWN*)
TEXT*GGENERAL CHARACTERISTICS ITEM DESCRIPTION
A RECORDING OF THE PHYSICAL,FUNCTIONAL,AND PERFORMANCE CHARACTERISTICS FOR AN ITEM OF SUPPLY.
Enter clear text.
(TEXTGCLEARTEXT)
Reply to this MRC in accordance with Volume 3.
AGAV*GEND ITEM IDENTIFICATION
THE NATIONAL STOCK NUMBER OR THE IDENTIFICATION INFORMATION OF THE END EQUIPMENT FOR WHICH THE ITEM IS A PART.
Enter the reply in clear text.
(AGAVG3930-00-000-0000*; AGAVGFORKLIFT TRUCK, SMITH CORPORATION, MODEL 12, TYPE A*)
Enter the word CAGE immediately followed by a colon, followed by a space then the 5 position Commercial and Government Entity (CAGE) Code, followed by a space and the letters PN immediately followed by a colon, a space and the part/model/reference number.
AVMF*AADDITIVE MANUFACTURING CAGE AND PART/MODEL NUMBER
THE ADDITIVE MANUFACTURER'S FIVE-DIGIT CAGE DESIGNATION AND THE PART/MODEL NUMBER.
CAGE: XXXXX PN: XXXXXXXXX
CAGE: XXXXX PN: XXXXXXXXX AND CAGE: XXXXX PN: XXXXXXXXX
(AVMFACAGE: 30003 PN: 4866113-485-AM*;AVMFACAGE: 30003 PN: 4866113-485-AM$$CAGE: 30003 PN: 5977224-120-AM)
FEAT*GSPECIAL FEATURES
THOSE UNUSUAL OR UNIQUE CHARACTERISTICS OR QUALITIES OF AN ITEM NOT COVERED IN THE OTHER REQUIREMENTS AND WHICH ARE DETERMINED TO BE ESSENTIAL FOR IDENTIFICATION ON ONE OR MORE OTHER FUNCTIONS.
Enter the reply in clear text. Separate multiple replies with a semicolon.
(FEATGADJUSTABLE NOSE CLIP*; FEATGADJUSTABLE NOSE PIECE; DISPOSABLE*)
Reply to this requirement only if the header record for the item identification for the item being identified has been coded as critical.
CRTL*ACRITICALITY CODE JUSTIFICATION
THE MASTER REQUIREMENT CODES OF THOSE REQUIREMENTS WHICH ARE TECHNICALLY CRITICAL BY REASON OF TOLERANCE,FIT,PERFORMANCE,OR OTHER CHARACTERISTICS WHICH AFFECT IDENTIFICATION OF THE ITEM.
Enter the Master Requirement Code for the requirement, the reply to which renders the item as being critical.
(CRTLAAKJA*; CRTLAAKJA$$ACSGS*)
If document availability code B, D, F, OR H, reply to MRC PRPY.
PRPY*APROPRIETARY CHARACTERISTICS
IDENTIFICATION OF THOSE CHARACTERISTICS INCLUDED IN THE DESCRIPTION FOR WHICH A NON-GOVERNMENT ACTIVITY HAS IDENTIFIED ALL OR SELECTED CHARACTERISTICS OF THE ITEM AS BEING PROPRIETARY AND THEREFORE RESTRICTED FROM RELEASE OUTSIDE THE GOVERNMENT WITHOUT PRIOR PERMISSION OF THE ORIGINATOR OF THE DATA.
Enter the MRC codes of the individual characteristics of the description which are marked proprietary on the technical data, using and coding ($) for multiple characteristics. If all the MRCS are proprietary, enter the reply PACS. If none of the MRCS is proprietary, enter the reply NPAC.
(PRPYAPACS*;PRPYANPAC*; PRPYAMATL$$ASURF*)
ELRN*GEXTRA LONG REFERENCE NUMBER
A REFERENCE NUMBER EXCEEDING 32 POSITIONS.
Enter the entire reference number. Do not include the 5-position Commercial and Government Entity (CAGE) Code unless there is more than one extra long reference number on the NSN.If there is more than one extra long reference number on the NSN, include the CAGE or NCAGE and separate each reference by using the "&" character.
(e.g., CAGE112036BIL060557LEN313605UZ62365 & CAGE112036BIL060557LEN313605UZ62365)
In determining quantity of characters in the reference number, count will be made after modification in accordance with Volume 2, Chapter 9, FLIS Procedures Manual, DoD 4100.39-M.
ZZZK*JSPECIFICATION/STANDARD DATA
THE DOCUMENT DESIGNATOR OF THE SPECIFICATION OR STANDARD WHICH ESTABLISHED THE ITEM OF SUPPLY.
Enter the applicable Reply Code from the table below, followed by the Commercial and Government Entity (CAGE) Code of the entity controlling the document, a dash, and the document designator. The agency that controls the limited coordination document must be preceded and followed by a slash following the designator. The word canceled or superseded must be preceded and followed by a slash for the designator. Professional and industrial association specifications/standards are differentiated from a manufacturer's specification in that the data has been coordinated and published by the professional and industrial association. Include amendments and revisions where applicable.
(ZZZKJT81337-30642B*;ZZZKJS81349-MIL-D-180 REV1/CANCELED/*;ZZZKJP80205-NAS1103*;ZZZKJS81349-MIL-C-1140C/CE/*;ZZZKJT81337-30642B$$JP80205-NAS1103*)
| Table 1 |
| Reply Code (AN62) | Reply |
| V | FEDERAL MOTOR VEHICLE SAFETY STANDARD |
| F | FLAMMABILITY STANDARD |
| S | GOVERNMENT SPECIFICATION |
| T | GOVERNMENT STANDARD |
| U | INTERNATIONAL STD/SPEC |
| D | MANUFACTURERS SOURCE CONTROL |
| R | MANUFACTURERS SPECIFICATION |
| N | MANUFACTURERS SPECIFICATION CONTROL |
| M | MANUFACTURERS STANDARD |
| B | NATIONAL STD/SPEC |
| A | PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| P | PROFESSIONAL/INDUSTRIAL ASSOCIATION STANDARD |
If the specification/standard cited in reply to MRC ZZZK is nondefinitive, reply to MRC ZZZT. This reply is the data which is not recorded in Segment C.
ZZZT*JNONDEFINITIVE SPEC/STD DATA
THE NUMBER, LETTER, OR SYMBOL INDICATING THE TYPE, STYLE, GRADE, CLASS, AND THE LIKE OF AN ITEM IN A NONIDENTIFYING SPECIFICATION OR STANDARD.
Enter the applicable Reply Code from the table below followed by the appropriate number, letter or symbol.
(ZZZTJTY1*; ZZZTJTY1$$JSTA*; ZZZTJTY1$JSTA*)
| Table 1 |
| Reply Code (AD08) | Reply |
| AL | ALLOY |
| BE | ANNEALED |
| AN | ANNEX |
| AP | APPENDIX |
| AC | APPLICABILITY CLASS |
| AR | ARRANGEMENT |
| AS | ASSEMBLY |
| AB | ASSORTMENT |
| BF | BOND |
| BX | BOX |
| CY | CAPACITY |
| CA | CASE |
| CT | CATEGORY |
| CF | CIRCUMFERENCE |
| CL | CLASS |
| CE | CODE |
| CR | COLOR |
| CC | COMBINATION CODE |
| CN | COMPONENT |
| CP | COMPOSITION |
| CM | COMPOUND |
| CD | CONDITION |
| AV | CONFIGURATION |
| CS | CONSTRUCTION |
| BG | CORE CONDITION |
| CB | CUT OFF |
| AM | DELAY CLASS |
| DE | DESIGN |
| DG | DESIGNATOR |
| DW | DRAWING NUMBER |
| DU | DUPLEX |
| EG | EDGE |
| EN | END |
| FY | FAMILY |
| FG | FIGURE |
| AK | FILE NUMBER |
| FN | FINISH |
| FB | FLAVOR |
| BH | FLUX PERCENTAGE |
| FM | FORM |
| FA | FORMULA |
| AJ | GAGE STOCK NUMBER |
| GR | GRADE |
| GA | GRADUATION |
| AX | GRANULES |
| AY | GRIT |
| GB | GROUND |
| GP | GROUP |
| HA | HEAVY DUTY |
| BA | IMAGE COLOR |
| NS | INSERT |
| TM | ITEM |
| KD | KIND |
| KT | KIT |
| LG | LENGTH |
| LV | LEVEL |
| LT | LIMIT |
| MK | MARK |
| AA | MARKER |
| AD | MASK APERTURE |
| ML | MATERIAL |
| BB | MAXIMUM DENSITY |
| TA | MEDIUM TEMPER |
| MH | MESH |
| ME | METHOD |
| BC | MINIMUM DENSITY |
| MD | MODEL |
| MT | MOUNTING |
| AQ | NATURAL |
| AU | NON-DELAY CLASS |
| NR | NUMBER |
| BL | OUTFIT NUMBER |
| PA | PARAGRAPH |
| PT | PART |
| PN | PATTERN |
| PC | PHYSICAL CONDITION |
| PS | PIECE |
| PL | PLAN |
| PR | POINT |
| PD | POLISHED |
| PB | PRESSURE RATING |
| QA | QUALITY |
| QB | QUENCHED |
| RN | RANGE |
| AE | RAPID |
| RT | RATING |
| RF | REFERENCE NUMBER |
| RA | REGULAR DUTY |
| BJ | RMA FLUX |
| SJ | SALIENT CHARACTERISTICS |
| SC | SCHEDULE |
| SB | SECTION |
| SL | SELECTION |
| BD | SERIALIZED |
| SE | SERIES |
| SV | SERVICE |
| SX | SET |
| SA | SHADE |
| SH | SHAPE |
| SG | SHEET |
| SZ | SIZE |
| AG | SLOW |
| TC | SOFT TEMPER |
| SK | SOURCE |
| PZ | SPECIES |
| SQ | SPECIFICATION SHEET |
| SD | SPEED |
| AW | STANDARD |
| SR | STRAIGHT |
| ST | STYLE |
| SS | SUBCLASS |
| SF | SUBFORM |
| SP | SUBTYPE |
| BK | SUPPORT |
| SN | SURFACE CONDITION |
| SY | SYMBOL |
| SM | SYSTEM |
| TB | TABLE |
| TN | TANNAGE |
| TP | TEMPER |
| TX | TEXTURE |
| TK | THICKNESS |
| TT | TREATMENT |
| TR | TRIM |
| TY | TYPE |
| YN | UNIT |
| AZ | UNSERIALIZED |
| VA | VARIETY |
| WT | WEIGHT |
| WD | WIDTH |
ZZZY*GREFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS
A FEATURE OF THE ITEM OF SUPPLY WHICH MUST BE SPECIFICALLY RECORDED WHEN THE REFERENCE NUMBER COVERS A RANGE OF ITEMS.
Enter the reply in clear text.
(ZZZYGCOLOR CODED LEADS*; ZZZYGAS DIFFERENTIATED BY MATERIAL*)
CXCY*GPART NAME ASSIGNED BY CONTROLLING AGENCY
THE NAME ASSIGNED TO THE ITEM BY THE GOVERNMENT AGENCY OR COMMERCIAL ORGANIZATION CONTROLLING THE DESIGN OF THE ITEM.
Enter the reply in clear text.
(CXCYGLINE PROCESSOR CONTROL BOARD*)
This MRC replaced MRC CTZZ
The FSCM identifies the manufacturer or Government agency whose number appears in the Part Number column. When an FSCM does not appear in the current issue of H4-1, H4-2, or H4-3 Cataloging Handbooks, the word "None" will appear in the FSCM column and the name and address of the manufacturer or Government agency will be shown in parentheses following the item description.
STTB*ASPECIAL TRUTH TABLE IDENTIFICATION
THE CONTROLLING ACTIVITY AND IDENTIFICATION OF THE SPECIAL CODED CONTACT SWITCHING STRUCTURE.
Enter the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document as in the first example.If ISAC coding is authorized for this requirement, enter the applicable ISAC from Table 1 below followed by the mode code and then the manufacturers 5-Digit Commercial and Government Entity (CAGE) Code listed in the FEDERAL SUPPLY CODE FOR MANUFACTURERS (FSCM) handbook, followed by a dash and the identifying number of the document as in the second example.
(STTBJ01963-SP35*; STTB1XJ19133-SPECIAL 0-1*)
| Table 1 |
| ISAC Field Indicator (5000) | Location |
| 3ABM | FIRST SECTION |
| 3ABN | SECOND SECTION |
| 3ABO | THIRD SECTION |
| 3ABP | FOURTH SECTION |
| 3ABQ | FIFTH SECTION |
| 3ABR | SIXTH SECTION |
| 3ABS | SEVENTH SECTION |
| 3ABT | EIGHTH SECTION |
| 3ABU | SINGLE SECTION |
| 3AEE | OVERALL |
| 3AFU | NINTH SECTION |
| 3AFV | TENTH SECTION |
| 3AFW | ELEVENTH SECTION |
| 3AFX | TWELFTH SECTION |
| 3AGK | EACH SECTION |
| 3HOU | LOCATION NOT OTHERWISE SPECIFIED |
CLQL*GCOLLOQUIAL NAME
A COMMON USAGE NAME BY WHICH AN ITEM IS KNOWN.
Enter the reply in clear text.
(CLQLGWOVEN WIRE CLOTH*)